Fuji Film 02000002 WIRELESS LAN MODULE User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1808523
Application ID	5q7fN4FN1/Ke3uioxSSNag==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.89kB (86101 bits)
Date Submitted	2012-10-04 00:00:00
Date Available	2013-04-02 00:00:00
Creation Date	2012-10-03 10:43:36
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2012-10-03 10:43:36
Document Title	User Manual
Document Creator	PScript5.dll Version 5.2.2

User Manual
WIRELESS LAN MODULE
MODEL FZ09913-200
The purpose of this manual is to explain correct way how to integrate module FZ09913-200 to the
end product. It includes procedures that shall assist you to avoid unforeseen problems. This
manual presents information that shows how module and OEM product, where module integrated,
complies with regulations in certain regions. Any modifications, not expressly approved by the
manufacturer could void the authority to operate in these regions.
The wireless LAN module, model FZ09913-200 has to be installed and used in accordance with the
technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this module is already
pre-approved) please contact the authorized local distributor or the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any wireless LAN
product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency
division multiplexing (OFDM) radio technology and to comply with the following standards.
･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11ｎ Standard on 2.4GHz Wireless LAN
Safety
The end product integrating this module, like other radio devices, emits radio frequency
electromagnetic energy. The level of energy emitted by this device, however, is less than the
electromagnetic energy emitted by other wireless devices such as mobile phones. The end product
integrating this module operates within the guidelines found in radio frequency safety standards
and recommendations.
These standards and recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who continually review and
interpret the extensive research literature. In some situations or environments, the use of the end
product integrating this module may be restricted by the proprietor of the building or responsible
representatives of the applicable organization. Examples of such situations include the following:
･Using the end product integrating this module onboard airplanes, or
･Using the end product integrating this module in any other environment
where the risk of interference with other devices or services is perceived or identified as being
harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific organization or
environment (an airplane, for example), ask for authorization to use the end product integrated into
this module before turning it on.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by tuning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Labeling:
Wireless LAN module FZ09913-200 labeled as below.
FCC ID: W2Z-02000002
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when
the module is installed into the system, “Contains FCC ID:
W2Z-02000002” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements and conditions
that must be observed to ensure compliance with the above-mentioned FCC RF Exposure
guideline.
If this module is intended for use in a portable device, integrators are responsible for separate
evaluation and/or approval to satisfy FCC RF Exposure requirements.
The antenna used this module is as follows;
Antenna Type: PCB printed antenna
Antenna Gain: -4.14dBi
If an antenna with higher gain or new antenna type is used with this module, integrators must
contact to manufacture for additional testing and submission to the FCC.
If other radio devices are to be integrated with this module, an additional evaluation and FCC
submission may be required. Integrators are responsible for such additional evaluation and FCC
submission.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of this device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for
successful communication.
Labeling:
Wireless LAN module FZ09913-200 labeled as below.
IC: 7736B-02000002
The proposed with IC ID label format is to be placed on the module. If IC ID is not visible when the
module is installed in to the system, “Contains IC: 7736B-09000002” shall be placed on the outside
of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with IC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating requirements and conditions
that must be observed to ensure compliance with the above-mentioned IC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible for separate
evaluation and/or approval to satisfy IC RF Exposure requirements.
The antenna used this module is as follows;
Antenna Type: PCB printed antenna
Antenna Gain: -4.14dBi
If an antenna with higher gain or new antenna type is used with this module, integrators must
contact manufacture for additional testing and submission to the IC.
If other radio devices are to be integrated with this module, an additional evaluation and IC
submission may be required. Integrators are responsible for such additional evaluation and IC
submission.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 
Create Date                     : 2012:10:03 10:43:36+09:00
Modify Date                     : 2012:10:03 10:43:36+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:785f65a2-2266-4136-b1fd-e5aa36e0a42b
Instance ID                     : uuid:50853602-9405-4a93-8e78-13b2632cce7b
Page Count                      : 6

EXIF Metadata provided by EXIF.tools