Fuji Film 02100006 Wi-Fi Module User Manual

Fuji Film Corporation Wi-Fi Module

Users Manual

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO: AMPAK WSDB-741 Setup Guide Rev. 0.1
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1 1. WLAN Function HW Setup Guide Physical hardware configuration likes as figure1. Please follow the following procedure step by step to get starting WLAN and Bluetooth function. Pin Assignment PIN NAME TYPE DESCRIPTION 1 GND G Ground connections 2 GND G Ground connections 3 RF_ANT I/O RF I/O Port (Option) 4 GND G Ground connections 5 GND G Ground connections 6 WL_GPIO2 I/O WLAN GPIO2(Internal 10K PD ) 7 GND G Ground connections 8 SDIO_DATA_CLK I/O SDIO clock line 9 GND G Ground connections 10 SDIO_DATA_2 I/O SDIO data line 2 11 SDIO_DATA_CMD I/O SDIO command line 12 SDIO_DATA_0 I/O SDIO data line 0 13 SDIO_DATA_3 I/O SDIO data line 3 14 SDIO_DATA_1 I/O SDIO data line 1 15 GND G Ground connections SDIO Board LED
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2 16 WL_HOST_WAKE (WL_GPIO_0) O WLAN to wake-up HOST 17 WL_GPIO1 I/O WLAN GPIO1(Internal 10K PD ) 18 WL_REG_ON I Internal regulators power enable/disable Chip has an internal default 200k Ohm pull-down resistor. It can be disabled through programming. 19 VDDIO P I/O Voltage supply input 20 GND G Ground connections 21 VBAT P Main power voltage source input 22 VBAT P Main power voltage source input 23 GND G Ground connections 24 BT_REG_ON I Internal regulators power enable/disable Chip has an internal default 200k Ohm pull-down resistor. It can be disabled through programming. 25 LPO_IN I External Low Power Clock input (32.768KHz) 26 GND G Ground connections 27 GND G Ground connections 28 PCM_CLK I/O PCM clock 29 PCM_SYNC I/O PCM sync signal 30 PCM_OUT O PCM Data output 31 PCM_IN I PCM data input 32 UART_RTS_N O Bluetooth UART interface 33 UART_CTS_N I Bluetooth UART interface 34 UART_TXD O Bluetooth/FM UART interface 35 UART_RXD I Bluetooth/FM UART interface 36 GND G Ground connections 37 BT_DEV_WAKE UP I HOST wake-up Bluetooth device 38 BT_HOST_WAKE O Bluetooth device to wake-up HOST 39-50 GND G Ground connections H1~H9 GND G BOT GND PAD (with open 9 solder mask)
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 3 Application Schematic 1. Software wi-fi setup:(Ubuntu 12.04 LTS kernel Linux3.4.0) 1-1.Put four files in the select document. 1. bcmdhd.ko 2. Fw.bin 3. Nvram.txt 4.Insmod 1-2. You have to marked the path of three files.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 4 1-3.Enter ”sudo –s” to root. 1-4.Change directory to the select document.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 5 1-5.Enter “./Insmod” to execute the file Insmod. 1-6.It will show the messege means success.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 6 2. Software Bluetooth setup:(Ubuntu 12.04 LTS kernel Linux3.2.0) 2-1. Change directory to document “brcm_patchram_plus” 2-2. Enter “./brcm_patchram_plus”. 2-3. Enter “ls /dev/” and you will found the device “ttyUSB0”.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 7 3-3. Put the HCD file to the path ” /brcm_patchram_plus/ur/brcm_patchram_plus/” and enter “./brcm_patchram_plus --enable_hci --no2bytes --tosleep 200000 --baudrate 115200 --patchram bcm43438a1.hcd /dev/ttyUSB0 –d” to download firmware.
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 8
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning 7KHHTXLSPHQWFRPSOLHVZLWK)&&5)H[SRVXUHOLPLWVVHWIRUWKIRUDQXQFRQWUROOHGHQYLURQPHQW7KHHTXLSPHQWPXVWQRWEHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHU AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information 9 Doc. NO:
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: W2Z-02100006 "and "Contains IC: 7736B-02100006" Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. Canada, Industry Canada (IC) Notices This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.The Wireless Device should be used in such a manner such that the potential for human contact during normaloperation is minimized. This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (“SAR”)limits when operated in portable exposure conditions. Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal.Ce dispositif a été évalué pour et démontré conforme à la Taux IC d'absorption spécifique ("SAR") des limites lorsqu'il est utilisé dans des conditions d'exposition portatifs. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information 10 Doc. NO:

Navigation menu