Fuji Film 02100006 Wi-Fi Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3660287
Application ID	pWcQUAYO3qUJ1A7nxh5F5Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.81kB (922645 bits)
Date Submitted	2017-12-01 00:00:00
Date Available	2017-12-05 00:00:00
Creation Date	2017-11-27 13:30:42
Producing Software	GPL Ghostscript 9.21
Document Lastmod	2017-12-01 19:44:20
Document Title	Untitled
Document Creator	PDF24 Creator
Document Author:	bart.lin

AMPAK
WSDB-741
Setup Guide
Rev. 0.1
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
1. WLAN Function HW Setup Guide
Physical hardware configuration likes as figure1. Please follow the following procedure step by
step to get starting WLAN and Bluetooth function.
SDIO Board
Pin Assignment
PIN
NAME
TYPE
DESCRIPTION
GND
Ground connections
GND
Ground connections
RF_ANT
I/O
RF I/O Port (Option)
GND
Ground connections
GND
LED
Ground connections
WL_GPIO2
I/O
WLAN GPIO2(Internal 10K PD )
GND
Ground connections
SDIO_DATA_CLK
I/O
SDIO clock line
GND
Ground connections
10
SDIO_DATA_2
I/O
SDIO data line 2
11
SDIO_DATA_CMD
I/O
SDIO command line
12
SDIO_DATA_0
I/O
SDIO data line 0
13
SDIO_DATA_3
I/O
SDIO data line 3
14
SDIO_DATA_1
I/O
SDIO data line 1
15
GND
Ground connections
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
16
WL_HOST_WAKE
(WL_GPIO_0)
17
WL_GPIO1
WLAN to wake-up HOST
I/O
WLAN GPIO1(Internal 10K PD )
18
WL_REG_ON
Internal regulators power enable/disable
Chip has an internal default 200k Ohm
pull-down resistor. It can be disabled
through programming.
19
VDDIO
I/O Voltage supply input
20
GND
Ground connections
21
VBAT
Main power voltage source input
22
VBAT
Main power voltage source input
23
GND
Ground connections
24
Internal regulators power enable/disable
Chip has an internal default 200k Ohm
pull-down resistor. It can be disabled
through programming.
BT_REG_ON
LPO_IN
External Low Power Clock input
(32.768KHz)
26
GND
Ground connections
27
GND
Ground connections
28
PCM_CLK
I/O
PCM clock
29
PCM_SYNC
I/O
PCM sync signal
30
PCM_OUT
PCM Data output
31
PCM_IN
PCM data input
32
UART_RTS_N
Bluetooth UART interface
33
UART_CTS_N
Bluetooth UART interface
34
UART_TXD
Bluetooth/FM UART interface
35
UART_RXD
Bluetooth/FM UART interface
36
GND
Ground connections
37
BT_DEV_WAKE UP
HOST wake-up Bluetooth device
38
BT_HOST_WAKE
Bluetooth device to wake-up HOST
39-50
GND
Ground connections
H1~H9
GND
BOT GND PAD
25
(with open 9 solder mask)
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
Application Schematic
1. Software wi-fi setup:(Ubuntu 12.04 LTS kernel Linux3.4.0)
1-1.Put four files in the select document.
1. bcmdhd.ko
2. Fw.bin
3. Nvram.txt
4.Insmod
1-2. You have to marked
the path of three files.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
1-3.Enter ”sudo –s” to root.
1-4.Change directory to the select document.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
1-5.Enter “./Insmod” to execute the file Insmod.
1-6.It will show the messege means success.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
2. Software Bluetooth
setup:(Ubuntu 12.04 LTS kernel Linux3.2.0)
2-1. Change directory to document
“brcm_patchram_plus”
2-2. Enter “./brcm_patchram_plus”.
2-3. Enter “ls /dev/” and you will found the device “ttyUSB0”.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
3-3. Put the HCD file to the path ” /brcm_patchram_plus/ur/brcm_patchram_plus/” and enter
“./brcm_patchram_plus --enable_hci --no2bytes --tosleep 200000 --baudrate 115200
--patchram bcm43438a1.hcd /dev/ttyUSB0 –d” to download firmware.
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
AMPAK Technology Inc.
Doc. NO:
www.ampak.com.tw
Proprietary & Confidential Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
RF exposure warning
7KHHTXLSPHQWFRPSOLHVZLWK)&&5)H[SRVXUHOLPLWVVHWIRUWKIRUDQXQFRQWUROOHGHQYLURQPHQW
7KHHTXLSPHQWPXVWQRWEHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRU
WUDQVPLWWHU
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may
be maintained between the antenna and users. The final end product must be labeled in a visible area with the
following: "Contains FCC ID: W2Z-02100006 "and "Contains IC: 7736B-02100006"
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Canada, avis d'Industry Canada (IC)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.
The Wireless Device should be used in such a manner such that the potential for human contact during normal
operation is minimized.
This device has been evaluated for and shown compliant with the IC Specific Absorption Rate (“SAR”)limits when
operated in portable exposure conditions.
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio
d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du
fonctionnement normal.
Ce dispositif a été évalué pour et démontré conforme à la Taux IC d'absorption spécifique ("SAR") des limites
lorsqu'il est utilisé dans des conditions d'exposition portatifs.
AMPAK
Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : bart.lin
Create Date                     : 2017:11:27 13:30:42+08:00
Modify Date                     : 2017:12:01 19:44:20+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : GPL Ghostscript 9.21
Creator Tool                    : PDF24 Creator
Metadata Date                   : 2017:12:01 19:44:20+08:00
Document ID                     : uuid:9bf9b4a6-d58f-11e7-0000-4f66e5c0b468
Instance ID                     : uuid:cdb1146a-ad8f-4381-8ab5-539ee09a96ae
Format                          : application/pdf
Title                           : Untitled
Creator                         : bart.lin
Page Count                      : 11

EXIF Metadata provided by EXIF.tools