Fujitsu 2012-001-SNB Communication Module User Manual ver1 3x

Download:
Mirror Download [FCC.gov]
Document ID	1781888
Application ID	7+MGFwoZeS3x0udjPBId4Q==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.03kB (175410 bits)
Date Submitted	2012-08-23 00:00:00
Date Available	2013-03-02 00:00:00
Creation Date	2012-08-28 16:44:24
Producing Software	PDF Printer / www.bullzip.com / CP / Freeware Edition
Document Lastmod	2012-08-28 16:44:24
Document Title	Microsoft Word - User manual_ver1.3.docx
Document Author:	00352273

User manual
User manual
Ver 1.3
1/10
User manual
Change history
revision
Updated date
1.0
Aug 1 2012
1.1
Aug 6 2012
1.2
August 15 2012
1.3
August 28 2012
summary
First edition
Modification
Page 6(DSSS/CCK->DSSS/BPSK),7(modification of consumption),
8(addition of following sentence)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
-Fixing of 3.1(delete comments of remarks)
- addition of 5.6 Indicating compliance with ICES-003
- Fixing of 4.3
2/10
User manual
Table of contents
1. Apprication .....................................................................................................................................4
2. System Configuration .....................................................................................................................4
3. Description of Meter (Host) ............................................................................................................5
3.1
Overview ....................................................................................................................................5
3.2
Operating Range ........................................................................................................................5
4. Description of Module ( Module) ....................................................................................................6
4.1
Overview ....................................................................................................................................6
4.2
Operating Range ........................................................................................................................6
4.3
Major element ............................................................................................................................6
4.4
Basic specification 【module】 ....................................................................................................7
5. Required FCC and IC statement ( Host ) .......................................................................................8
5.1
FCC §15.21 ................................................................................................................................8
5.2
FCC §15.105 ..............................................................................................................................8
5.3
RSS-Gen §7.1.2. ........................................................................................................................8
5.4
RSS-Gen §7.1.3. ........................................................................................................................8
5.5
Indicating safe separation distance warning ..............................................................................9
6. Required FCC and IC statement (Module)...................................................................................10
6.1
FCC §15.21 ..............................................................................................................................10
6.2
FCC §15.105 ............................................................................................................................10
6.3
RSS-Gen §7.1.2. ......................................................................................................................10
6.4
RSS-Gen §7.1.3. ......................................................................................................................10
3/10
User manual
1. Apprication
This document shows the description of wattmeter（hereinafter called meter）and mounted
communication board（hereinafter called module）.
target meters : GE I210+ Meter FM1S / FM2S / FM12S / FM25S
Module
: Fujitsu YAA75-0402
2. System Configuration
Fig2-1 is general system configuration of using meter.
Installed meters in each house is communicated to Center via Repeaters and Gateways and control
the meter-reading value etc.automatically.
Red line of Fig.2-1 is the applicable scope of this document.
Gateway
Switch
Repeaters
Meters
Fiber-opt
network Router
Server
…..
Router
DHCP Server
Center
Substation
Poles
Fig2-1 System configuration
4/10
Houses
User manual
3. Description of Meter (Host)
3.1 Overview
Form and overview of meter are as follows.
Category
Input voltage
FM1S
120VAC
enclosure
Meter panel
board
Meter socket
type
Mouted module
meter panel
interface
AC power
cable
Meter form
FM2S
FM12S
240VAC
120VAC
or 240VAC
Same form
Same board
Remark
FM25S
120VAC
or 240VAC
Different type
Same module
Same interface
Same cable
3.2 Operating Range
• Voltage
• Temperature
• Typical Starting Watts
• Typical Watts Loss
• Typical Accuracy
+ - 20% (or ±20%)
-40°C through +85°C
<=5.0 Watts (Form 2S 240V CL200)
0.7 Watts
Within +/- 0.2%
5/10
User manual
4. Description of Module ( Module)
4.1 Overview
The module mounted to each meter in paragraph 3 collects the meter-reading values etc.
with controlling Center.
4.2 Operating Range
Same as chapter 3.2.
4.3 Major element
Major elements of module are as follows.
No.
component
1 Radio element
Antenna
Meter panel
interface
element
Power element
Dispray element
２
summary
IEEE802. 11b
Transmission power:100mW
Modulation：DSSS / BPSK
Data rate ：1Mbps
This antenna made by printed-circuit in the module.
Communication between Meter panel.
Signals:refer to chapter 3.2
*AC cable(with ferrite bead) is connected to
this element.
*This element steps down AC input(120V/240V) to
+3.3VDC.
extinction power off or normal operation
blinking
No operation ( start-up firmware)
lighting
No operation(reset / no service)
extinction normal
blinking
fault
lighting
reset
remark
LED(green)
LED(red)
Meter
module
Meter
panel
*Display
*Meter
information
collection
UART/
Control
signal
Meter
panel
Interface
element
Radio
element
120/
240VAC
From electric pole
120VAC / 240VAC
Meter
Socket
+3.3VDC
AC cable with ferrite bead
Power
element
120VAC
/ 240VAC
6/10
antenna
element
User manual
4.4 Basic specification 【module】
】
No
1 External
interface
Item
Wireless
specification
IEEE802. 11b
Meter Panel
Connector（10pin）
Power
Input : AC85～264V
RESET
MB86C90
AR2315
LED
FRES1/2 Short-circuit
JTAG:×1
JTAG:×1
Status
：GREEN
Alarm
：AMBER
Program Deletion
AC-DC Conversion （120V/240V⇒3.3V）
50/60Hz
Input : Less than 8.49W(AC:120V/240V)
Output : Less than 5.94W(DC:+3.3V)
Debug
interface
Display
Security
Power
Tamper
Input
Frequency
consumption
Condition
Operating
temperature
Cooling method
Thunder surge
Protection fuse
-20℃～40℃
Air cooling without blower
varistor
fuse
7/10
User manual
5. Required FCC and IC statement ( Host )
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
5.1 FCC §15.21
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
5.2 FCC §15.105
For class B equipment:
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
5.3 RSS-Gen §7.1.2.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
5.4 RSS-Gen §7.1.3.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
8/10
User manual
5.5 Indicating safe separation distance warning
This equipment complies with radio frequency exposure limits set forth by the FCC and Industry
Canada for an uncontrolled environment. This equipment should be installed and operated with a
Minimum distance of 20cm between the device and the user or bystanders. This device must
Not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux radiofréquences définies par la FCC et
Industrie Canada pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre le dispositif et l'utilisateur ou des tiers. Ce dispositif ne doit pas
être utilisé a proximité d’une autre antenne ou d’un autre émetteur.
5.6 Indicating compliance with ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe or B est conforme à la norme NMB-003 du Canada
9/10
User manual
6. Required FCC and IC statement (Module)
6.1 FCC §15.21
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
6.2 FCC §15.105
For class B equipment:
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
6.3 RSS-Gen §7.1.2.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
6.4 RSS-Gen §7.1.3.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
10/10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 10
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
Producer                        : PDF Printer / www.bullzip.com / CP / Freeware Edition
Modify Date                     : 2012:08:28 16:44:24+09:00
Create Date                     : 2012:08:28 16:44:24+09:00
Creator Tool                    : UnknownApplication
About                           : af79be16-f33f-11e1-0000-f3b670f66d4.�^�.2012-08-28T16:44:24+09:00
Document ID                     : uuid:af79be16-f33f-11e1-0000-f3b670f66d4Ъ†^�c..
Format                          : application/pdf
Title                           : Microsoft Word - User manual_ver1.3.docx
Creator                         : 00352273
Author                          : 00352273

EXIF Metadata provided by EXIF.tools