Furrion FOD43TA-BL Digital wireless observation system User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2708345
Application ID	QtMru4FLU1ZFey+btQcIDQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	335.6kB (4195036 bits)
Date Submitted	2015-08-08 00:00:00
Date Available	2015-08-08 00:00:00
Creation Date	2015-01-12 15:17:20
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-02-10 10:29:49
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Windows)

Digital Wireless Observation System
Operating and Installation
Instructions
This manual is for use with
Furrion FOS48TA-BL
Digital Wireless Observation System
Furrion FOS48TAPK-BL
Digital Wireless Observation System
With FRCBRKT-BL Mounting Bracket pre-installed.
Welcome
Furrion FOS48TAPK-BL Digital Wireless Observation System
Includes FRCBRKT-BL Mounting Bracket
Furrion FRCBRKT-BL Digital Wireless Observation System
For vehicles with FRCBRKT-BL Mounting Bracket pre-installed.
Thank you for purchasing a Furrion Digital Wireless Observation System.
Furrion’s digital wireless observation system is one of the easiest rear view camera
systems to install in your trailer, truck or RV. All that is required is a connection of a
single DC power supply to the rear camera from a running light power source.
The Furrion digital wireless observation system uses digital wireless technology
giving the major benefit of superior signal transmission with low interference on
a single bandwidth channel. This means the Furrion camera unit eliminates the
interferences which other analogue signal systems are subject to, meaning the
Furrion digital system gives you a clearer picture of what is behind you no matter
where you are.
This Furrion system with integrated antenna attached to the camera has been
specifically designed for use on trailers, trucks, 5th wheels, caravans and RV’s.
This system has been designed for extended range applications or security
monitoring.
Before installation and use, please read all instructions carefully. This will ensure
safe use and reduce the risk of injury to persons.
Contents
IMPORTANT SAFETY INSTRUCTIONS.................................................................4
System Parts............................................................................................................5
Installation Mounting Bracket...................................................................................6-7
Installation Camera Wiring..........................................................................................7
Installation Mounting Bracket cont..............................................................................8
Camera Installation..................................................................................................9
Camera Positioning...............................................................................................10
Monitor Installation................................................................................................11
Pairing..............................................................................................................12
Picture Control.......................................................................................................13
Trouble Shooting....................................................................................................14
Specifications....................................................................................................15
IMPORTANT SAFETY INSTRUCTIONS
READ THESE INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR USING THE SYSTEM
Electrical Safety
Installation
A battery or 12 or 24V DC electrical
system presents a risk of electrical
shock or burn hazard. Ensure all power
sources are isolated before installation.
Installation & wiring of this product
require specialist skill. To ensure proper installation and to ensure safety,
please seek a specialist technician.
Insulate unconnected wires with vinyl
tape or similar.
Use insulated tools when working
with a power supply.
Use watertight connectors for
camera power supply cable to power
source.
Caution
Use 16AWG or larger cables to supply power to the camera unit.
There are no user serviceable parts
in the Furrion Digital Wireless Observation System. Do not disassemble or
attempt any repairs.
There are no fuses or disconnects
in the Furrion Digital Wireless Observation System. Install external fuses/
breakers as required.
Care
Do not wash the vehicle with an
automatic car wash or high pressure
water. This may damage the camera.

bre cloth, do not use course or abrassive materials.
Do not use alcohol or amonia based
products to clean the LCD screen.
Only use specialist screen cleaning
products.
Use a wet cloth to clean the camera lens. A dry cloth may scratch the
camera lens.
Only use parts supplied or recommended.
Connect rear the camera to a 830V DC circuit only.
Ensure correct polarity of DC power
supply to the camera

camera only to a circuit provided with
a maximum branch-circuit over current
protection device.
Don’t route wiring in areas that may
get hot.
Take necessary precautions when
working at elevated levels.
System Parts
FOS48TAPK-BL
Digital Wireless
Observation System
LCD Monitor
Monitor Stand
Monitor Power Cable
Camera
FRCBRKT-BL
Digital Wireless
Observation System
Camera Bracket
Camera Bracket
Gasket
Camera Power
Cable
Installation
Mounting Bracket
(If the FRCBRKT-BL Mounting is pre-installed please go to page 9)
Caution
• E
 nsure there are no electrical
cables, gas lines, pipes or other important parts behind where the drill
holes will be.
• During installation, remove the key
from the ignition & isolate the 12v or
24v power source.
Suitable installation position
• W
 here practical, as high as possible
at the rear of the vehicle.
• In the horizontal centre of the vehicle or as close as.
Vehicle Centre
Camera
Bracket
Vehicle Roof
Suitable installation position..
• Mount the camera directly above
the red running lights.
• At least 2” away from any lighting.
Close proximity to lights may cause
image blooming, blurring and reduced night vision performance.
• The area should be flat with enough
surface area to accommodate the
bracket.
• The surface area should be clean &
dry for a watertight installation.
• Ensure that power can be fed to
the installation area from within the
vehicle.
Installation
Mounting Bracket
1 Use the Bracket Gasket to
mark and outline where the centre
hole will be drilled then drill a 5/8th”
hole.
2 Feed the supplied 6ft Camera
Power Cable through the gasket.
Ensure the bare wire end of the cable
goes into the vehicle and the flat side
of the gasket faces inward.
Vehic
le
Wall
Camera Power
Cable
Bracket
Gasket
Wiring the Camera
Electrical Power
• To use the Digital Wireless Observation System for observation purposes, it
needs to be wired to a constant 12V/ 24V power source. e.g If connected to runnig lights, the running lights must be on for the system to operate.
• To use it as a reversing camera, it can be wired to a circuit that comes on when
the vehicle is reversing.e.g reversing lights
Connects to
Camera
Connects to
12V/ 24V
Power Supply
• Ensure correct polarity when wiring
the cables. RED + BLACK • Wire connections & terminals must
be sealed to be waterproof.
•  When connecting wires, ensure
the circuit is isolated by disconnecting the - negative terminal on the
battery.
Installation
Mounting Bracket
3 Mount the gasket & bracket to the
rear of the vehicle. Ensure that the
Camera Power Cable does not get
caught between the vehicle wall &
gasket or the Bracket & Gasket.
3 Fix the Gasket & Bracket to the
rear of the vehicle using 4 x #2 head
3/4” self tapping screws. (other screws
can be used depending on side wall
material.) Ensure the sealing lip
around the edge of the gasket is seated over the edge of the bracket before
fully tightening the screws.
Vehic
le
Wall
Bracket
Mounting Bracket
If only installing the FRCBRKT-BL
Mounting Bracket, secure the Camera
Power Cable inside the mounting and
attach the cover.
Installation
Camera Installation
FRCBRKT-BL Pre-install only
If installing to a pre-installed
FRCBRKT-BL Mounting Bracket,
remove the cover by unscrewing the 2
screws.
1 Locate the Camera Power Con-
2 Ensure the camera antenna is
nector from within the Bracket and
connect it to the Camera Plug.
secured tight.
2 Secure the camera to the Bracket
using the 4 screws.
Camera
Power
Connector
Camera
Plug
Installation
Camera Positioning
The camera can be tilted up & down to
obtain the best viewing angle.
Positioning the Camera
• Adjust the camera up or down then
check the view via the monitor.
• If the camera is to be used as parking camera, part of the vehicle, such
as the bumper, should be visible on
the monitor.
10
Installation
Monitor Installation
Positioning the Monitor
• Ensure the the is placed so that it does not obstruct vision when driving.
• Do not place in an area where it might interfere with driving.
• The surface area should be clean, smooth & flat.
With the lock open,
position the mount.
Press mount down
against the surface.
Adjusting the View Angle
• Swivel & Tilt the mount to set the
optimum viewing angle.
• Lock the position by tightening the
locking screws. 1
Push the mount lock
down.
Connecting the Monitor
• Route the power cable to the vehicle’s cigarette lighter socket/12/24V power
outlet. The cable must not interfere with the safe operation of the vehicle.\
• Insert the small 12/24 Volt DC plug of the power cable into the right side of the
monitor.
• Plug the 12/24 Volt cigarette lighter plug into the vehicle’s cigarette lighter
socket.
11
Operation
Pairing
After installation, the camera & monitor need to be paired.
This only needs to be done once.
Menu
Up
Menu/ Return
Up
Power/ Confirm
Down
Line
Down
Line
Pairing procedure
Ensure both the camera and monitor have power supplied.
The vehicle may need to be running
1. Bring the monitor to within close proximity for pairing.
2. Press the Power button to turn on the monitor.
3. Press the Menu button, this will bring up 4 icons on the screen.
4. Use the Up & Down buttons to scroll across to the Pair icon.
5. Press the Power/ Confirm button to start pairing. A Pair icon will be displayed.
6. Press the small button on the underside of the camera for 2 seconds.
7. An OK Pair icon will be displayed once pairing is complete.
12
Operation
Pairing
PAIRING FAILED will appear on the monitor after 13 seconds if the pairing procedure has been unsuccessful.
*For better pairing results, bring the monitor closer to the camera.
Unpairing
To unpair the camera from the monitor, exit the menu, press & hold Down for 5
seconds.
Picture Control
Using the Up & Down buttons to navigate and adjust and the Power/ Confirm button to confirm selections, the monitors view settings can be adjusted to suit various
viewing preferences.
Picture Settings
Brightness
Contrast
Color
Picture Rotation
13
Troubleshooting
Problem
Solution / Issue
Monitor won’t turn on
-Check that power cable is connected
-Check the cigarette lighter has 12-14V DC Output
-Check the fuse in the cigarette socket adaptor
Camera & Monitor won’t
pair
-Check if the camera is receiving power
-Reduce the distance between the camera & moni
tor during pairing.
-Make sure to hold the camera pairing button for 2
seconds.
Intermittent/ Weak signal
icon appears
correctly - it should be vertical.
Distance between camera & monitor is too great.
Interference from overhead power lines may be
affecting the signal.
Try unpairing and pairing.
14
Camera
Monitor
Voltage
DC8-30V
DC8-30V
Current
≤300mA
≤200mA
≤300M (outdoors)
≤300M (outdoors)
Standby Current
Wireless Range
≤1mA
Wireless Frequency
Image Sensor
2.4Ghz
1/4” Color CMOS VGA
LCD Display
Camera
4.3” 480*272
Max 25frames/sec VGA
f1.7mm, F2.0
IR
View Distance ≥1.5m
Brightness ≥ 2Lux
Receiver Sensitivity
Working Temperature
-78±3dBm
-10/+50
-10/+50
15
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment .This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This product is backed by Furrions 12 month product warranty
See warranty card for terms & conditions.
16
Furrion reserve the right to alter the information in this document without prior notice.
Furrion shall not be liable for technical or editorial errors or omissions contained herein.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2015:01:12 15:17:20+08:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2015:02:10 10:29:49+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2015:02:10 10:29:49+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Thumbnail Width                 : 180
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 7381 bytes, use -b option to extract)
Instance ID                     : uuid:b7d4c3a3-e545-4ded-8189-c2d228cbcd7b
Original Document ID            : xmp.did:752968BAFE94E411A8B3F180F715042A
Document ID                     : xmp.id:5D5812D62A9AE4119800ECF47434F6DF
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:01:12 15:17:20+08:00
Derived From Instance ID        : xmp.iid:5C5812D62A9AE4119800ECF47434F6DF
Derived From Document ID        : xmp.did:752968BAFE94E411A8B3F180F715042A
Derived From Original Document ID: xmp.did:752968BAFE94E411A8B3F180F715042A
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : True
Max Page Size W                 : 148.000269
Max Page Size H                 : 210.000102
Max Page Size Unit              : Millimeters
Font Name                       : ArialMT, Arial-BoldMT
Font Family                     : Arial, Arial
Font Face                       : Regular, Bold
Font Type                       : Open Type, Open Type
Font Version                    : Version 5.10, Version 5.08
Font Composite                  : False, False
Font File Name                  : arial.ttf, arialbd.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : 默认色板组
Swatch Groups Group Type        : 0
Page Count                      : 16

EXIF Metadata provided by EXIF.tools