Furrion FOD43TA-BL Digital Wireless Observation System User Manual instruction manual
Furrion Ltd. Digital Wireless Observation System instruction manual
Furrion >
Contents
- 1. instruction manual
- 2. User Manual
instruction manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2556372 |
| Application ID | A3XBOndocaB19rX9IBMpRw== |
| Document Description | instruction manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 335.64kB (4195441 bits) |
| Date Submitted | 2015-03-16 00:00:00 |
| Date Available | 2015-03-17 00:00:00 |
| Creation Date | 2015-01-12 15:17:20 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2015-02-10 10:29:49 |
| Document Title | instruction manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Digital Wireless Observation System Operating and Installation Instructions This manual is for use with Furrion FOS48TA-BL Digital Wireless Observation System Furrion FOS48TAPK-BL Digital Wireless Observation System With FRCBRKT-BL Mounting Bracket pre-installed. Welcome Furrion FOS48TAPK-BL Digital Wireless Observation System Includes FRCBRKT-BL Mounting Bracket Furrion FRCBRKT-BL Digital Wireless Observation System For vehicles with FRCBRKT-BL Mounting Bracket pre-installed. Thank you for purchasing a Furrion Digital Wireless Observation System. Furrion’s digital wireless observation system is one of the easiest rear view camera systems to install in your trailer, truck or RV. All that is required is a connection of a single DC power supply to the rear camera from a running light power source. The Furrion digital wireless observation system uses digital wireless technology giving the major benefit of superior signal transmission with low interference on a single bandwidth channel. This means the Furrion camera unit eliminates the interferences which other analogue signal systems are subject to, meaning the Furrion digital system gives you a clearer picture of what is behind you no matter where you are. This Furrion system with integrated antenna attached to the camera has been specifically designed for use on trailers, trucks, 5th wheels, caravans and RV’s. This system has been designed for extended range applications or security monitoring. Before installation and use, please read all instructions carefully. This will ensure safe use and reduce the risk of injury to persons. Contents IMPORTANT SAFETY INSTRUCTIONS.................................................................4 System Parts............................................................................................................5 Installation Mounting Bracket...................................................................................6-7 Installation Camera Wiring..........................................................................................7 Installation Mounting Bracket cont..............................................................................8 Camera Installation..................................................................................................9 Camera Positioning...............................................................................................10 Monitor Installation................................................................................................11 Pairing..............................................................................................................12 Picture Control.......................................................................................................13 Trouble Shooting....................................................................................................14 Specifications....................................................................................................15 IMPORTANT SAFETY INSTRUCTIONS READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE SYSTEM Electrical Safety Installation A battery or 12 or 24V DC electrical system presents a risk of electrical shock or burn hazard. Ensure all power sources are isolated before installation. Installation & wiring of this product require specialist skill. To ensure proper installation and to ensure safety, please seek a specialist technician. Insulate unconnected wires with vinyl tape or similar. Use insulated tools when working with a power supply. Use watertight connectors for camera power supply cable to power source. Caution Use 16AWG or larger cables to supply power to the camera unit. There are no user serviceable parts in the Furrion Digital Wireless Observation System. Do not disassemble or attempt any repairs. There are no fuses or disconnects in the Furrion Digital Wireless Observation System. Install external fuses/ breakers as required. Care Do not wash the vehicle with an automatic car wash or high pressure water. This may damage the camera. bre cloth, do not use course or abrassive materials. Do not use alcohol or amonia based products to clean the LCD screen. Only use specialist screen cleaning products. Use a wet cloth to clean the camera lens. A dry cloth may scratch the camera lens. Only use parts supplied or recommended. Connect rear the camera to a 830V DC circuit only. Ensure correct polarity of DC power supply to the camera camera only to a circuit provided with a maximum branch-circuit over current protection device. Don’t route wiring in areas that may get hot. Take necessary precautions when working at elevated levels. System Parts FOS48TAPK-BL Digital Wireless Observation System LCD Monitor Monitor Stand Monitor Power Cable Camera FRCBRKT-BL Digital Wireless Observation System Camera Bracket Camera Bracket Gasket Camera Power Cable Installation Mounting Bracket (If the FRCBRKT-BL Mounting is pre-installed please go to page 9) Caution • E nsure there are no electrical cables, gas lines, pipes or other important parts behind where the drill holes will be. • During installation, remove the key from the ignition & isolate the 12v or 24v power source. Suitable installation position • W here practical, as high as possible at the rear of the vehicle. • In the horizontal centre of the vehicle or as close as. Vehicle Centre Camera Bracket Vehicle Roof Suitable installation position.. • Mount the camera directly above the red running lights. • At least 2” away from any lighting. Close proximity to lights may cause image blooming, blurring and reduced night vision performance. • The area should be flat with enough surface area to accommodate the bracket. • The surface area should be clean & dry for a watertight installation. • Ensure that power can be fed to the installation area from within the vehicle. Installation Mounting Bracket 1 Use the Bracket Gasket to mark and outline where the centre hole will be drilled then drill a 5/8th” hole. 2 Feed the supplied 6ft Camera Power Cable through the gasket. Ensure the bare wire end of the cable goes into the vehicle and the flat side of the gasket faces inward. Vehic le Wall Camera Power Cable Bracket Gasket Wiring the Camera Electrical Power • To use the Digital Wireless Observation System for observation purposes, it needs to be wired to a constant 12V/ 24V power source. e.g If connected to runnig lights, the running lights must be on for the system to operate. • To use it as a reversing camera, it can be wired to a circuit that comes on when the vehicle is reversing.e.g reversing lights Connects to Camera Connects to 12V/ 24V Power Supply • Ensure correct polarity when wiring the cables. RED + BLACK • Wire connections & terminals must be sealed to be waterproof. • When connecting wires, ensure the circuit is isolated by disconnecting the - negative terminal on the battery. Installation Mounting Bracket 3 Mount the gasket & bracket to the rear of the vehicle. Ensure that the Camera Power Cable does not get caught between the vehicle wall & gasket or the Bracket & Gasket. 3 Fix the Gasket & Bracket to the rear of the vehicle using 4 x #2 head 3/4” self tapping screws. (other screws can be used depending on side wall material.) Ensure the sealing lip around the edge of the gasket is seated over the edge of the bracket before fully tightening the screws. Vehic le Wall Bracket Mounting Bracket If only installing the FRCBRKT-BL Mounting Bracket, secure the Camera Power Cable inside the mounting and attach the cover. Installation Camera Installation FRCBRKT-BL Pre-install only If installing to a pre-installed FRCBRKT-BL Mounting Bracket, remove the cover by unscrewing the 2 screws. 1 Locate the Camera Power Con- 2 Ensure the camera antenna is nector from within the Bracket and connect it to the Camera Plug. secured tight. 2 Secure the camera to the Bracket using the 4 screws. Camera Power Connector Camera Plug Installation Camera Positioning The camera can be tilted up & down to obtain the best viewing angle. Positioning the Camera • Adjust the camera up or down then check the view via the monitor. • If the camera is to be used as parking camera, part of the vehicle, such as the bumper, should be visible on the monitor. 10 Installation Monitor Installation Positioning the Monitor • Ensure the the is placed so that it does not obstruct vision when driving. • Do not place in an area where it might interfere with driving. • The surface area should be clean, smooth & flat. With the lock open, position the mount. Press mount down against the surface. Adjusting the View Angle • Swivel & Tilt the mount to set the optimum viewing angle. • Lock the position by tightening the locking screws. 1 Push the mount lock down. Connecting the Monitor • Route the power cable to the vehicle’s cigarette lighter socket/12/24V power outlet. The cable must not interfere with the safe operation of the vehicle.\ • Insert the small 12/24 Volt DC plug of the power cable into the right side of the monitor. • Plug the 12/24 Volt cigarette lighter plug into the vehicle’s cigarette lighter socket. 11 Operation Pairing After installation, the camera & monitor need to be paired. This only needs to be done once. Menu Up Menu/ Return Up Power/ Confirm Down Line Down Line Pairing procedure Ensure both the camera and monitor have power supplied. The vehicle may need to be running 1. Bring the monitor to within close proximity for pairing. 2. Press the Power button to turn on the monitor. 3. Press the Menu button, this will bring up 4 icons on the screen. 4. Use the Up & Down buttons to scroll across to the Pair icon. 5. Press the Power/ Confirm button to start pairing. A Pair icon will be displayed. 6. Press the small button on the underside of the camera for 2 seconds. 7. An OK Pair icon will be displayed once pairing is complete. 12 Operation Pairing PAIRING FAILED will appear on the monitor after 13 seconds if the pairing procedure has been unsuccessful. *For better pairing results, bring the monitor closer to the camera. Unpairing To unpair the camera from the monitor, exit the menu, press & hold Down for 5 seconds. Picture Control Using the Up & Down buttons to navigate and adjust and the Power/ Confirm button to confirm selections, the monitors view settings can be adjusted to suit various viewing preferences. Picture Settings Brightness Contrast Color Picture Rotation 13 Troubleshooting Problem Solution / Issue Monitor won’t turn on -Check that power cable is connected -Check the cigarette lighter has 12-14V DC Output -Check the fuse in the cigarette socket adaptor Camera & Monitor won’t pair -Check if the camera is receiving power -Reduce the distance between the camera & moni tor during pairing. -Make sure to hold the camera pairing button for 2 seconds. Intermittent/ Weak signal icon appears correctly - it should be vertical. Distance between camera & monitor is too great. Interference from overhead power lines may be affecting the signal. Try unpairing and pairing. 14 Camera Monitor Voltage DC8-30V DC8-30V Current ≤300mA ≤200mA ≤300M (outdoors) ≤300M (outdoors) Standby Current Wireless Range ≤1mA Wireless Frequency Image Sensor 2.4Ghz 1/4” Color CMOS VGA LCD Display Camera 4.3” 480*272 Max 25frames/sec VGA f1.7mm, F2.0 IR View Distance ≥1.5m Brightness ≥ 2Lux Receiver Sensitivity Working Temperature -78±3dBm -10/+50 -10/+50 15 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Product: Digital Wireless Observation System(FOS48TA-BL) Trade Name: FURRION Model Name: FOS48TA-BL Serial Model: FOD43TA-BL, FOC48TA-BL This product is backed by Furrions 12 month product warranty See warranty card for terms & conditions. 16 Furrion reserve the right to alter the information in this document without prior notice. Furrion shall not be liable for technical or editorial errors or omissions contained herein.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2015:01:12 15:17:20+08:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2015:02:10 10:29:49+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2015:02:10 10:29:49+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Thumbnail Width : 180 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 7381 bytes, use -b option to extract) Instance ID : uuid:b7d4c3a3-e545-4ded-8189-c2d228cbcd7b Original Document ID : xmp.did:752968BAFE94E411A8B3F180F715042A Document ID : xmp.id:5D5812D62A9AE4119800ECF47434F6DF Rendition Class : proof:pdf History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2015:01:12 15:17:20+08:00 Derived From Instance ID : xmp.iid:5C5812D62A9AE4119800ECF47434F6DF Derived From Document ID : xmp.did:752968BAFE94E411A8B3F180F715042A Derived From Original Document ID: xmp.did:752968BAFE94E411A8B3F180F715042A Derived From Rendition Class : default Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 148.000269 Max Page Size H : 210.000102 Max Page Size Unit : Millimeters Font Name : ArialMT, Arial-BoldMT Font Family : Arial, Arial Font Face : Regular, Bold Font Type : Open Type, Open Type Font Version : Version 5.10, Version 5.08 Font Composite : False, False Font File Name : arial.ttf, arialbd.ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Page Count : 16EXIF Metadata provided by EXIF.tools