Furuno USA 9ZWFS1575 GMDSS SSB User Manual FS1575 2575 5075 OME Frontcover

Furuno USA Inc GMDSS SSB FS1575 2575 5075 OME Frontcover

users manual part 2

6. MENU OPERATION6-121) Rotate the ENTER knob to select [+0.00 kHz] then push the knob.2) Rotate the ENTER knob to adjust the receiving frequency (setting value: -0.20 to +0.20). 6.13 External Alarm SettingThe [EXTERNAL ALARM] menu enables/disables output of the contact signal for ur-gency, safety and routine frequencies to an external alarm system.1. Rotate the ENTER knob to select [SYSTEM] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [EXTERNAL ALARM] then push the knob.3. Rotate the ENTER knob to select [URGENCY], [SAFETY] or [ROUTINE], then push the knob.4. Rotate the ENTER knob to select [ON] or [OFF] then push the knob.6.14 NETWORK SettingView your network settings on the [NETWORK SETTING (VIEW)] screen.1. Rotate the ENTER knob to select [SYSTEM] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [NETWORK] then push the knob.
6. MENU OPERATION6-136.15 Address BookYou can register a maximum of 50 MMSI or the address name (max. 20 letters) in the memory.6.15.1 List for address data1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [ADDRESSBOOK] then push the knob.6.15.2 How to register addresses1. Open the [ADDRESS BOOK] screen.2. Press the 5 key to open the [ADDRESS DATA ENTRY] screen.Key/knob FunctionENTER • Move the cursor by rotating the ENTER knob.• Open the [ADDRESS DATA EDIT] screen by pushing the ENTER knob (see paragraph 6.15.3)..CANCEL Return to the [MENU] screen.1Go to the previous page.3Go to the next page.4Delete address (see paragraph 6.15.4).5Open the [ADDRESS DATA ENTRY] screen (see paragraph 6.15.2).6Switch the address type. Each press changes the type continuously (SHIP → COAST → GROUP → SHIP → ...).When 50 addresses are registered, this is not available.
6. MENU OPERATION6-143. With [NAME] selected, push the ENTER knob.4. Enter the address name (max. 20 letters) with the numeric keys then push the EN-TER knob.5. With [MMSI] selected, push the ENTER knob.6. Enter the MMSI with the numeric keys then push the ENTER knob.7. With [REGISTER] selected, push the ENTER knob.6.15.3 How to edit addresses1. Open the [ADDRESS BOOK] screen.2. Rotate the ENTER knob to select the address to edit then push the knob.3. Rotate the ENTER knob to select [NAME] or [MMSI] as appropriate then push the knob.4. Enter the address name or MMSI with the numeric keys then push the ENTER knob.5. Rotate the ENTER knob to select [REGISTER] then push the knob.Note: If the MMSI is already registered to another address, the error alarm sounds and a warning pop-up message appears when selecting [REGISTER].6. Rotate the ENTER knob to select [Yes] then push the knob.Push the ENTER knob.LIST: 24 : 20 : 6MMSI number overlaps. : Close window
6. MENU OPERATION6-156.15.4 How to delete addressesOpen the [ADDRESS BOOK] screen then follow the applicable procedure below.Individual address1. Rotate the ENTER knob to select the address to delete then press the 4 key.2. With [DELETE SELECTION] selected, push the ENTER knob.3. Rotate the ENTER knob to select [Yes] then push the knob.Address by type1. Press the 6 key several times to select desired type.2. Press the 4 key.3. Rotate the ENTER knob to select [DELETE LIST] then push the knob.4. Rotate the ENTER knob to select [Yes] then push the knob.All addresses1. Press the 4 key.2. Rotate the ENTER knob to select [DELETE ALL LISTS] then push the knob.3. Rotate the ENTER knob to select [Yes] then push the knob.6.15.5 How to create a DSC message with registered address1. Open the [ADDRESS BOOK] screen.2. Rotate the ENTER knob to select the address to use.3. Press the OTHER DSC MSG key to open the [COMPOSE MESSAGE] screen.Press the OTHER DSC MSG key.N06 HNKYULIST: 24 : 20 : 6
6. MENU OPERATION6-166.16 TX Message PreparationFor the individual, PSTN, group and test messages, you can create messages and store them in the memory for future use. You can edit, send or delete these messages. A maximum of 100 messages can be stored into the memory.6.16.1 List for message files1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [MSG FILE] then push the knob.Detailed information screen for message filesRotate the ENTER knob to se-lect the message file desired on the [MESSAGE FILE] list then push the knob. The de-tailed information screen for the selected message file ap-pears as shown right.Several functions can be done from this screen.• 1 key: Go to the detailed in-formation screen for the previous message file.Key/knob FunctionENTER • Move the cursor by rotating the ENTER knob.• Open the detailed information screen for the selected message file by pushing the ENTER knob (see the following "Detailed information screen for message files").CANCEL Return to the [MENU] screen.1Go to the previous page.3Go to the next page.4Delete messages (see paragraph 6.16.8).5Open the [MESSAGE FILE ENTRY] screen.6Switch the message type. Each press changes the type continuously (INDIVIDUAL → GROUP → PSTN → TEST → INDIVIDUAL → ...).When 100 messages are registered, this is not available.1070 29
6. MENU OPERATION6-17• 3 key: Go to the detailed information screen for the next message file.• 4 key: Delete the selected message file. The following message appears on the screen.Rotate the ENTER knob to select [Yes] then push the knob.6.16.2 Individual calls1. Open the [MESSAGE FILE] list.2. Press the 5 key to open the [MESSAGE FILE ENTRY] screen.3. With [MSG TYPE] selected, push the ENTER knob.4. Rotate the ENTER knob to select [INDIVIDUAL MSG] then push the knob.5. With [TO] selected, push the ENTER knob.6. Rotate the ENTER knob to select [DIRECT INPUT] or [ADDRESS BOOK DATA] then push the knob.[ADDRESS BOOK DATA]: Select a MMSI from the [ADDRESS BOOK] (see section 6.15) then push the ENTER knob.[DIRECT INPUT]: Enter the MMSI of coast station or ship station with the numeric keys then push the ENTER knob.7. With [COMM MODE] selected, push the ENTER knob.8. Rotate the ENTER knob to select the communication mode then push the knob.9. Rotate the ENTER knob to select [DSC FREQ] then push the knob.10. Rotate the ENTER knob to select DSC frequency referring to "How to set DSC fre-quency" on page 5-2 then push the knob. The communication frequency changes in conjunction with DSC frequency. If you change the communication frequency, go to step 11. If not, go to step 13.11. Rotate the ENTER knob to select [COMM FREQ] then push the knob.12. Set the communication frequency referring to "How to set working channel, fre-quency" on page 5-3 then push the ENTER knob.
6. MENU OPERATION6-1813. Rotate the ENTER knob to select [FILE NAME] then push the ENTER knob.14. Enter the file name (max. 20 letters) with the numeric keys.15. With [REGISTER] selected, push the ENTER knob.6.16.3 Group callsTo receive group calls, register the group MMSI as follows:1. Open the [MESSAGE FILE] list.2. Press the 5 key to open the [MESSAGE FILE ENTRY] screen.3. With [MSG TYPE] selected, push the ENTER knob.4. Rotate the ENTER knob to select [GROUP MSG] then push the knob.5. With [TO] selected, push the ENTER knob.6. Enter the group MMSI (eight digits) with the numeric keys then push the ENTER knob.7. With [COMM MODE] selected, push the ENTER knob.8. Rotate the ENTER knob to select [TELEPHONE] or [NBDP-FEC] then push the knob.9. Rotate the ENTER knob to select [DSC FREQ] then push the knob.10. Rotate the ENTER knob to select DSC frequency referring to "How to set DSC fre-quency" on page 5-2 then push the knob. The communication frequency changes in conjunction with DSC frequency. If you change the communication frequency, go to step 11. If not, go to step 13.11. Rotate the ENTER knob to select [COMM FREQ] then push the knob.12. Set the communication frequency referring to "How to set working channel, fre-quency" on page 5-3 then push the ENTER knob.13. With [FILE NAME] selected, push the ENTER knob.14. Enter the file name (max. 20 letters) with the numeric keys.15. With [REGISTER] selected, push the ENTER knob.6.16.4 PSTN calls1. Open the [MESSAGE FILE] list.2. Press the 5 key to open the [MESSAGE FILE ENTRY] screen.3. With [MSG TYPE] selected, push the ENTER knob.4. Rotate the ENTER knob to select [PSTN MSG] then push the knob.5. With [TO] selected, push the ENTER knob.6. Enter the MMSI of coast station (seven digits) with the numeric keys then push the ENTER knob.7. With [TEL] selected, push the ENTER knob.
6. MENU OPERATION6-198. Enter the telephone no. (up to 16 digits) with the numeric keys then push the EN-TER knob.9. With [DSC FREQ] selected, push the ENTER knob.10. Rotate the ENTER knob to select DSC frequency referring to "How to set DSC fre-quency" on page 5-2 then push the knob.11. With [FILE NAME] selected, push the ENTER knob.12. Enter the file name (max. 20 letters) with the numeric keys.13. With [REGISTER] selected, push the ENTER knob.6.16.5 Test call1. Open the [MESSAGE FILE] list.2. Press the 5 key to open the [MESSAGE FILE ENTRY] screen.3. With [MSG TYPE] selected, push the ENTER knob.4. Rotate the ENTER knob to select [TEST MSG] then push the knob.5. With [TO] selected, push the ENTER knob.6. Rotate the ENTER knob to select [DIRECT INPUT] or [ADDRESS BOOK DATA] then push the knob.[ADDRESS BOOK DATA]: Select a MMSI from the [ADDRESS BOOK] (see section 6.15) then push the ENTER knob.[DIRECT INPUT]: Enter the MMSI where to send the test message with the nu-meric keys then push the ENTER knob.7. With [DSC FREQ] selected, push the ENTER knob.8. Rotate the ENTER knob to select DSC frequency desired then push the knob.9. With [FILE NAME] selected, push the ENTER knob.10. Enter the file name (max. 20 letters) with the numeric keys.11. With [REGISTER] selected, push the ENTER knob.6.16.6 How to edit prepared messages1. Open the [MESSAGE FILE] list.2. Rotate the ENTER knob to select the message file to edit then push the knob.
6. MENU OPERATION6-203. Push the ENTER knob to open [MESSAGE FILE EDIT] screen.4. Rotate the ENTER knob to select the item to edit then push the knob.5. Change the setting accordingly.6. Rotate the ENTER knob to select [REGISTER] then push the knob.7. Rotate the ENTER knob to select [Yes] then push the knob.6.16.7 How to send prepared messagesHow to send without modification1. Open the [MESSAGE FILE] list.2. Rotate the ENTER knob to select the message file desired then press the OTHER DSC MSG key.3. Rotate the ENTER knob to select [GO TO CALL] then push the knob.Edit before sendingFollow the procedure in paragraph 6.16.6 and do the above procedure "How to send without modification".6.16.8 How to delete prepared messagesIndividual prepared messageOpen the [MESSAGE FILE] list then follow the applicable procedure below.1. Rotate the ENTER knob to select the file to delete then press the 4 key.2. With [DELETE SELECTION] selected, push the ENTER knob.3. Rotate the ENTER knob to select [Yes] then push the knob.
6. MENU OPERATION6-21Prepared messages by type1. Press the 6 key several times to select the desired type.2. Press the 4 key.3. Rotate the ENTER knob to select [DELETE LIST] then push the knob.4. Rotate the ENTER knob to select [Yes] then push the knob.All prepared messages1. Press the 4 key.2. Rotate the ENTER knob to select [DELETE ALL LISTS] then push the knob.3. Rotate the ENTER knob to select [Yes] then push the knob.6.17 How to Set the AUTO ACK DetailsThe acknowledgement message can be sent automatically when you receive an indi-vidual message or a PSTN message. You can also enable or disable it for position, polling and test messages. For PSTN, position and polling messages, automatic ac-knowledge is disabled with an active DSC session.Note 1: For individual message, the automatic acknowledgement is automatically dis-abled, as required by law, when an RX call contains an error.Note 2: For individual message, the auto acknowledgement message can not be sent when there are RT and/or DSC sessions.1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [ACK SETTINGS] then push the knob.Default:[AUTO (UNABLE)][AUTO (ABLE)]: Send ABLE acknowledgement automatically.[AUTO (UNABLE)]: Send UNABLE acknowledgement automatically.Sets reason for UNABLE. This menu item is only for use with PSTN. Default: [MANUAL] [AUTO (ABLE)]: Send automatic acknowledgement of position request.[AUTO (UNABLE)]: Send automatic acknowledgement of no position information.[MANUAL]: Send manual acknowledgement.Default: [AUTO][AUTO]: Send automatic acknowledgement of polling request.[MANUAL]: Send manual acknowledgement of polling request.Default: [AUTO][AUTO]: Send automatic acknowledgement of test call.[MANUAL]: Send manual acknowledgement of test call.Default: [NO REASON]Default:[AUTO (ABLE)]If you cannot use the frequency or mode specified by a sending station, [CAN'T USE CH] is automatically sent.
6. MENU OPERATION6-226.18 Special MessagesPermission to transmit NEUTRAL CRAFT and MEDICAL TRANSPORT is enabled or disabled as follows:1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [SPECIAL MSG] then push the knob.3. Rotate the ENTER knob to select [NEUTRAL] or [MEDICAL] then push the knob.4. Rotate the ENTER knob to select [ABLE] or [UNABLE] then push the knob.6.19 How to Set Scan FrequenciesThe [ROUTINE/DISTRESS SCAN] menus determine which DSC routine and distress frequencies to scan. Follow the instructions below to select/deselect DSC routine and distress frequencies to scan.Routine frequencies1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [ROUTINE SCAN] then push the knob.3. Rotate the ENTER knob to select [SCAN1] (2, 3, 4, 5 or 6) then push the knob.4. Rotate the ENTER knob to select frequency band then push the knob.5. Rotate the ENTER knob to select frequency desired then push the knob.[INTL]: International channels[LOCAL1/LOCAL2]: Local channels[DIST]: Distress channels
6. MENU OPERATION6-23Note: Distress frequencies can be stored on the routine frequency memory. This is convenient for backing up the watch-keeping receiver.Distress, urgency and safety frequencies1. Rotate the ENTER knob to select [DSC] on the [MENU] screen then push the knob.2. Rotate the ENTER knob to select [DISTRESS SCAN] then push the knob.3. Rotate the ENTER knob to select frequency band then push the knob.4. Rotate the ENTER knob to select [ON] or [OFF] as appropriate then push the knob.Note: Regulations require that 2 MHz and 8 MHz and one more DSC distress frequen-cy should be watched continuously. 2 MHz and 8 MHz cannot be turned off. Maximum three bands can be turned off.6.20 Sound SettingThe [AUDIO] menu lets you set the volume for the following items:Rotate the ENTER knob to select [AUDIO] on the [MENU] screen then push the knob.• Key click on (setting: [1] - [3]) or off (setting: [0]) (Two beeps sound when a key inop-erative in the ON mode (setting: [1] - [3]) is operated.)• Speaker on or off with off hook for handset• Volume of the receiving alarm for the safety and routine messages• Turn sound alarm on or off for the distress alarm received from a ship in distress which is more than 500 NM from your ship.
6. MENU OPERATION6-246.21 Alarm ListsThe [ALARM] menu shows all currently violated alarms. When an error occurs, a pop-up message and the flashing error icon appear on the screen. Press the CANCEL key to close the pop-up message and stop the flashng of the error icon. When the error is removed, the error icon disappears.Rotate the ENTER knob to select [ALARM] on the [MENU] screen then push the knob. The following screen appears.There are seven kinds of errors: TX PLL UNLOCK, RX PLL UNLOCK, WR1 PLL UN-LOCK, WR2 PLL UNLOCK, MAIN AMP HEATED, SHIP’S MAIN FAILURE, VC ER-ROR.Errors are displayed in the order shown above, not in the order of occurrence. An error is deleted from the list when the cause for the error is removed.Default: [2]Turn beep on (setting: [1] - [3]) or off (setting: [0]) when a key is pressed.Default: [MUTE]Turn the speaker on or off when the handset is off hook.Rotate the ENTER knob to set volume then push the knob.Default: [500NM]Turn sound alarm on or off for the distress alarm received from a ship in distress which is more than 500 NM from your ship.Error iconTX PLL UNLOCKWR1 PLL UNLOCK
7-17. NBDP SYSTEM OVERVIEW7.1 How to Turn on the NBDP SystemTurn on the terminal unit and the printer with their respective power switches.Note 1: To power on the system, turn on the control unit then turn on the NBDP ter-minal unit.Note 2: The printer PP-510 prints messages. Refer to its operator's manual for oper-ation.7.2 Description of Equipment7.2.1 Terminal unitThe terminal unit is a visual display incorporating a floppy disk drive (for IB-583) or an SD card drive (IB-585). To adjust the brilliance, press the Alt key while pressing the F6 key to lower the brilliance; the F7 key to raise it. Eight levels of brilliance are avail-able.When the terminal unit is turned on, the communication status screen, shown below, appears. This is where all phases of telex communications begin.Communication status screenTERMINAL UNIT IB-583Power switchFloppy disk drivePRINTER PP-510Power switchTERMINAL UNIT IB-585Power switchSD card drive“ ”
7. NBDP SYSTEM OVERVIEW7-2Features of the IB-583The IB-583 has a battery (Type: CR2450-F2ST2L, Code no.: 000-144-941) on its TERM/CPU Board (16P0209) and its life is about six years. When the voltage of the battery gets low, the time is wrong. When this occurs, contact your dealer about re-placement of the battery.Russian modeThe terminal unit is fitted with both English and Russian modes. Select the desired mode as below:"English-mode": Turn on the terminal unit while pressing the E key."Russian-mode": Turn on the terminal unit while pressing the R key.This mode is stored.In "Russian-mode", there are two input shift status; "English-shift" and "Russian-shift". In the "Russian-shift" status, the alphabet keys are used as Cyrillic keys.Note 1: To switch between Russian and English input, press the Alt key while holding down the Shift key. (This is available in Russian mode only.) "Eng" or "Rus" appears on the top right of the screen. This shift status is not stored. When you turn on the pow-er next time, you reset the shift status as necessary.Note 2: The comma and period can not be entered in the "Russian-shift" status. To enter these characters, switch to the "English-shift" status.Note 3: can not be entered in "Russian-mode". is replaced with "4" in NBDP communication.7.2.2 KeyboardThe terminal unit is operated from the keyboard. Operation is simplified by the use of menus which you access by pressing a function key, labeled F1-F10 at the top of the keyboard. The figures below show the function menus and their corresponding func-tion keys.Keyboard for IB-583Keyboard for IB-585“Ë” and “Ъ” “Ч”5!1@2#3$4%5^6+=&77(99Back-spaceHome88)0Pg UpQ W E R T Y I{[}]\TabU4O6P-Pg DnA S D F GH"'Enter EnterCapsLockJ1K2L3:;+EndShiftZ X C V B N<,?//>.M0ShiftCtrlCtrl FnAlt Alt Ins DelEsc F3 F4 F5 F6 F7 F8 F9 F10NumLockPrt ScSys RqScrollLock PauseBreakF1F11F2F125_-~,.F1: FILEF2: EDITF3: OPERATEF4: WINDOWF5: STATIONF6: SYSTEMF7: WRUF8: HRF9: OVERF10: BREAKFunction keysDo not use these keys.The indication “ScrLk” means the Russian shift is active. (It does not mean “scroll lock”.)F1: FILEF2: EDITF3: OPERATEF4: WINDOWF5: STATIONF6: SYSTEMF7: WRUF8: HRF9: OVERF10: BREAKFunction keys
7. NBDP SYSTEM OVERVIEW7-3Note 1: The correct letters may not be entered when connecting a keyboard except the supplied one.Note 2: Both Russian and English input are available in the Russian mode. Put the keytop label supplied on the keyboard during the Russian mode.Note 3: The carriage-return and line-feed codes "CR LF" are automatically sent with pressing the Enter key during NBDP communication. Press the ← or ↓ key if you want to send only "CR" or "LF".Note 4: "Letter Shift" and "Figure Shift" are automatically inserted if necessary. If you want to send them purposely, press the following keys:• "Letter Shift": Ctrl + Shift + L• "Figure Shift": Ctrl + Shift + F• "NOINF" ("Cyrillic Shift" in Russian mode): Ctrl + Shift + RNote 5: Do not connect or disconnect the keyboard during operating the terminal unit.7.3 Function Keys, Menu OperationThe function keys at the top of the keyboard control most of operations through a menu system. Most of the screenshots on this manual are for IB-585.7.3.1 Menu conventionsReverse highlightingThe cursor-selected menu item is displayed with white characters on a black back-ground.UnderlineThe underline shows the currently selected option. In the figure below, for example, [ARQ], [Channel] and [ON] are underlined.[Station Entry] screenReverse highlightingUnderlineStation
7. NBDP SYSTEM OVERVIEW7-47.3.2 Menu overviewMenu selectionPress a function key to open a menu. To display the [File] menu, for exam-ple, press the function key F1.Selection of menu items and op-tionsPress a numeric or alphabet key to se-lect a menu item. You can also select a menu item to press the ← or → key then press the Enter key. Menu op-tions can be selected by the ← or → key. After selecting an option, press the Enter key to register your selec-tion.How to close the menuPress and hold down the Esc key for over a second to close the menu.7.3.3 Function key descriptionFunction key F1: [File] menuThe [File] menu is where you create, open, save and print telex messages. Floppy disks or SD cards are also formatted by this menu.1: Open a new untitled window.2: Open files saved on floppy disks or SD cards.3: Close files with saving or discarding.4: Delete files on floppy disks or SD cards.5: Rename files on floppy disks or SD cards.6: Turn real time printing on or off.7: Print files on floppy disks or SD cards.8: Stop printing and clear the print buffer.9: Clear the communication buffer.0: Format an SD card for IB-585, or a floppy disk for IB-583.A: Execute this menu before removing an SD card.B: Open a macro window.*1*2*2*1: [Floppy Disk Format] for IB-583*2: Only for IB-585
7. NBDP SYSTEM OVERVIEW7-5Function key F2: [Edit] menuThe [Edit] menu provides a full line of editing features.Function key F3: [Operate] menuThe [Operate] menu mainly controls transmission and reception.1: Cancel the last change (cut, copy or paste).2: Remove the selected text and store it in the paste buffer. (Previous text in the paste buffer is cleared.)3: Copy the selected text and store it in the paste buffer. (Previous text in the paste buffer is cleared.)4: Insert the text stored in the paste buffer at the current location of the cursor.5: Select the entire current file for cut or copy.6: Search a word or a character string.7: Replace a word with a different word or char-acter string.8: Put the cursor to the top line of the current file.9: Put the cursor to the last line of the current file.0: Move the cursor to the desired line in the cur-rent file.A: Switch between the display window 1 and 2.1: Select a station on the station list.2: Enable macro operation. For details, see section 10.10.3: Select a file (to transmit).4: Stop sending a file.5: Start/stop frequency scanning.6: Select communication mode for reception; AUTO, ARQ, FEC.Note: Do not select DIRC.7: Timer programming.8: Set TX mode and subscriber's ID number and start manual calling.9: Set TX and RX frequencies and start waiting for reception.0: Set ITU or user channel and start waiting for reception.1: Call Station3: File to Send4: Cancel Sending5: Scan (Start/Stop)6: Manual Reception7: Timer Operation8: Manual Calling9: Set Frequency0: Set Channel*Operate2: Macro Operation *: Only for IB-585
7. NBDP SYSTEM OVERVIEW7-6Function key F4: [Window] menuThe [Window] menu lets you display the corresponding data of the window below.Function key F5: [Station] menuThe [Station] menu provides for storage of stations, timer program setup, user channel setup, and entry of various ID codes.1: Display desired calendar month and year. To change year or month, select item with the ↑ or ↓ key and change setting with the ← or → key.2: Display all distress frequencies (see the fol-lowing table).3: Turn on or off the screen saver function. For details, see section 8.7.1: Register stations.2: Register timer programs.3: Register scan groups for scanning.4: Register user channels.5: Register own ship's answerback code.6: Register own ship's group ID code (4 or 5 dig-its).7: Register own ship's group ID code (9 digits).8: Register own ship's selective ID code (4 or 5 digits).9: Register own ship's selective ID code (9 dig-its).Note: For IB-585, the numbers after 5 are moved up.**: Only for IB-5851: Station Entry2: Timer Operation Entry3: Scan Entry4: User Channel Entry*5: Answerback Code Entry6: Group ID Entry (4/5 digit)7: Group ID Entry (9 digit)8: Select ID Entry (4/5 digit)9: Select ID Entry (9 digit)Station*: Only for IB-583
7. NBDP SYSTEM OVERVIEW7-7Function key F6: [System] menuThe [System] menu is mainly for use by technicians and contains diagnostic tests. To change settings, select [Change] from the item [Setup] and operate the arrow keys to select item and option. Press the Enter key to register the selection and close the menu.Menu item Function[Setup] Lock, change settings, restore default system settings.[Slave Delay] Set the length of the slave delay timing from the end of RX to the start of TX in the ARQ mode. The default setting is suitable in most cases. This item cannot be adjusted by the user.[TX/RX MSG Save]Turn on to automatically save incoming and outgoing messages to a floppy disk or a SD card. "Log" appears at the top of the screen when on.[Edit Before sending][OFF] transmits key operation one by one. [ON] transmits message only when the Enter key is pressed after confirming text typed.[TX POWER] (only forIB-585)Change output power during transmission. ([HIGH], [MID], [LOW] (for FS-1575/2575), [LOW1] (for FS-5075), [LOW2] (for FS-5075))[Header/Foot-er] (only forIB-585)Turn on or off the indication of header and footer. When starting trans-mission, display time & date for starting transmission, MMSI for com-munication party, TX and RX frequencies. When ending transmission, display time & date for ending transmission.[Time System] Select time system.[OFF]: No time indication, [UTC]: Coordinated universal time,[SMT]: Local time, [JST]: Japan standard timeSetupSlave DelayTX/RX MSG SaveEdit before SendingTX Power*Header/Footer*Time SystemTime & DateWindow ColorSelf TestLock Change Default12 msec (10 - 50 msec)OFF ONOFF ONHIGH MID LOWOFF ONOFF UTC SMT JST10-Apr-2012 10:00:00System*: Only for IB-585ARQ mode signal sequence3 char. RX 3 char. RXSlave Delay TimingRX end TX startACK signal
7. NBDP SYSTEM OVERVIEW7-8Function key F7: WRU (Who Are You?)In the ARQ mode, request other station's answerback code.Function key F8: HR (Here Is)In the ARQ mode, send your ship's answerback code.Function key F9: OVERIn the ARQ mode, switch the direction of traffic; the information receiving station switches to the information sending station, the information sending station switches to the information receiving station.Function key F10: BreakDisconnect the line or cancel the standby.[Time & Date] Enter date and time manually. If a navigation device is connected, the time is automatically set when the power is turned on or whenever the time system is switched. Manual entry takes priority over automatic entry. This item cannot be adjusted when using [UTC] or [JST].[WindowColor]Select display colors. For details, see section 8.6.[Self Test] Start diagnostic test.Menu item Function
8-18. NBDP PREPARATIONSThis chapter provides the procedures necessary for preparing the NBDP terminal unit. For automatic telex, you need to register the following:• Your ship's ID and answerback codes mandatory• Stations• Timer programs• Scan channel groups• User channels8.1 Registration of Answerback & ID CodesEnter your ship's answerback and ID codes as shown below.Note: The answerback and ID codes cannot be changed once entered; be sure to cor-rectly enter the codes.8.1.1 How to register answerback code1. Press the function key F5 then the 4 key for IB-585 or the 5 key for IB-583 to open the [An-swerback Code Entry] screen.2. Enter your ship's answerback code (numbers, space, 4 capital letters, space, X) then press the Enter key. The prompt "OK/Cancel" asks for confirmation of the data.Example of answerback code: 123456789 FURU X.3. If the code is correct, press the Enter key again. For final confirmation of the data, the "Caution" shown in the illustration below appears.Message for confirmation of code entered4. If the code is correct, press the Enter key again.
8. NBDP PREPARATIONS8-28.1.2 How to register ID codes1. Press the function key F5 then the 5, 6, 7 or 8 key for IB-585 to enter the Group ID Code (4 or 5 digits), Group ID Code (9 digits), Select ID Code (4 or 5 digits) or Select ID Code (9 dig-its), respectively. (For IB-583, press the function key F5 then the 6, 7, 8 or 9 key.)2. Enter Group ID or Select ID then press the Enter key. A prompt asks for confir-mation of the data.3. If the ID is correct, press the Enter key. For final confirmation of the data, the "Caution" shown in the illustration below appears.Message for confirmation of code entered4. If the ID is correct, press the Enter key again.8.2 User ChannelsThe user channels can be used in scanning entry and station entry.For IB-585, the user channels are set by the transceiver unit. See section 6.2. For IB-583, the user channel list provides storage for up to 100 user channels, numbered 0 - 99. See the following paragraphs.8.2.1 How to register user channels1. Press the function key F5 then the 4 key to open the [User Channel Entry] screen.2. If [Create] is not underlined, press the →, ↑ and Enter keys to underline it. Channel
8. NBDP PREPARATIONS8-33. With [Channel] selected, enter a channel number.Note 1: 100 channels can be registered. When you attempt to register more, the message "Channel memory is full. Press any key to escape." appears. In this case delete unnecessary channels to register new ones.Note 2: If the channel entered already exists, the message "Channel by that num-ber already exists. Press any key to escape." appears. Press any key then enter another number.4. Press the ↓ key to select [Tx Freq]. Enter TX frequency.5. Press the ↓ key to select [Rx Freq]. Enter RX frequency.6. Press the Enter key. The [OK/Cancel] confirmation window appears.7. Press the Enter key. Channel number entered appears in the [Channel List].8. Press the Esc key to close the menu.8.2.2 How to edit/delete user channels1. Press the function key F5 then the 4 key to open the [User Channel Entry] screen.2. Press the ↓ key to select a channel from the [Channel List].3. Press the → key then the ↓ key to select [Change] and press the Enter key.4. Do one of the following:Edit channel: Use the ↑, ↓ and Backspace keys to make corrections.Delete channel: Erase channel number with the Backspace key.5. Press the Enter key twice.6. Press the Esc key.8.3 Station ListThe station list stores up to 50 stations, one frequency pair (RX and TX) per station. For stations which have more than one frequency pair, you can add a suffix to the sta-tion name to denote multiple frequency pairs. For example, station name FURUNO followed by -1, -2, -3, etc. for each frequency pair required.8.3.1 How to register stations1. Press the function key F5 then the 1 key to open the [Station Entry] screen. On the right side of the screen, [Create] and [Change] are shown.Station IB-583Station IB-585
8. NBDP PREPARATIONS8-42. If [Create] is not underlined, press the →, ↑ and Enter keys to underline it.3. With [Station] selected, enter station name using up to 18 characters.4. Press the ↓ key to select [ID Code]. Enter station ID code.5. Press the ↓ key to select [Mode]. Select either communication mode with the ← or → keys.[ARQ]: Automatic Retransmission Request[FEC]: Forward Error Correction6. Press the ↓ key to select [CH/Table]. Select [Channel] or [ScanTable].7. Press the ↓ key to select [Num/Table].If you selected [Channel] at step 6, enter ITU channel number (see Appendix 2) or User channel number. Go to step 10.If you selected [ScanTable] at step 6, press the → key to show the scan group list registered. For the scan group, refer to section 8.5.8. Select a scan group name by using the ↓ or ↑ key then press the Enter key. For IB-583, go to step 10. For IB-585, go to the next step.Example window for Scanning Group List9. Press the ↓ key to select [Rephasing]. Select [ON] or [OFF].Note: The default setting is [ON]. Select [ON] under normal use. The disconnec-tion by error is processed quickly with [OFF] when communicating with the party which does not have rephasing function.10. Press the Enter key. The prompt [OK/Cancel] asks for verification of data.11. If the data is correct, press the Enter key. (To cancel entry, press the ↓ key to se-lect [Cancel] then press the Enter key. Data entered are erased.) The station name entered at step 3 appears at the [Station List] window.12. To register other stations, press the Enter key twice then repeat steps 3 through 10.13. Press the ↓ key. Check data on the [Station List] for correctness. The stations dis-played in reverse video on the [Station List] are displayed on [Station Set Up].14. Press the Esc key to quit.Note 1: If you enter a station which already exists, the indication "Station by that name already exists. Press any key to escape." appears. Press any key to return to the [Sta-tion List]. Check the list.Note 2: The station entry beginning with "DSC" is special entry which is automatically registered by DSC function.INTREPID
8. NBDP PREPARATIONS8-58.3.2 How to edit/delete stations1. Press the function key F5 then the 1 key to open the [Station Entry] screen.2. Press the ↓ key to select a station name from the [Station List].3. Press the → key then the ↓ key to select [Change] and press the Enter key.4. Do one of the following;Edit station: Use the ↑, ↓ and the Backspace keys to make corrections.Delete station: Erase station name with the Backspace key.5. Press the Enter key twice.6. Press the Esc key.8.4 Timer ProgrammingA built-in timer allows you to automatically receive and transmit files. 10 timer pro-grams can be registered. To enable timer operation, see section 10.6.8.4.1 How to register timer programs1. Press the function key F5 then the 2 key to open the [Timer Operation Entry] screen.2. If [Create] is not underlined, press the →, ↑ and Enter keys to underline it.3. With [Operation] selected, enter a suitable operation name on the [Operation] line. Any alphanumeric characters can be used.Note: If the operation name entered already exists, the message "Operation name already exists. Press any key to escape." appears. Press any key and change the operation name.4. Press the ↓ key to select [Station].5. Press the → key to display [Station List] (which you registered stations in the pre-vious paragraph).6. Press the ↓ or ↑ key to select a station then press the Enter key.7. Press the ↓ key to select [Start Time]. Enter start time, in 24-hour notation. To have the operation start at 8:35 a.m., for example, the keying sequence would be0 8 3 5 0 0.Operation Press the  key to show the station list, the file list.
8. NBDP PREPARATIONS8-68. Press the ↓ key to select [Stop Time]. Enter stop time, in 24-hour notation.9. Press the ↓ key to select [Receive/Send]. Select operation category; [Receive] or [Send]. If you select [Send], go to step 10. For [Receive], go to step 12.10. For [Send], insert the floppy disk or the SD card to the drive then press the ↓ key to select [File to Send].11. Press the → key to open the TX window, select a file, then press the Enter key twice.12. Press the Enter key. A confirmation message appears.13. Press the Enter key. The operation name appears in [Timer Operation List].14. To enter another timer program, press the Enter key twice and repeat steps 3 to 13.15. Press the Esc key to close the menu.8.4.2 How to edit/delete timer programs1. Press the function key F5 then the 2 key to open the [Timer Operation Entry] screen.2. Press the ↓ key to select a timer program name from the [Timer Operation List].3. Press the → key then the ↓ key to select [Change] and press the Enter key.4. Do one of the following;Edit program: Use the ↓, ↑ and the Backspace keys to make corrections.Delete program: Erase operation name with the Backspace key.5. Press the Enter key twice.6. Press the Esc key.8.5 Scan Channel GroupsYou can store up to 10 scan groups, 20 channels per group.The NBDP terminal unit can control radio equipment through channel scanning. In the FEC mode, the radio equipment scans a number of channels (according to your se-lection), stopping when an synchronous code is found. In the ARQ mode it stops when your own ID code is detected in an incoming signal. Also, in the ARQ mode, the trans-mitter is then tuned to the corresponding transmitter frequency, the communication link is established and the traffic is automatically exchanged. Scanning resumes once the link is disconnected.
8. NBDP PREPARATIONS8-78.5.1 How to register scan channel groupsYou can register ITU and user scan channels as follows:1. Press the function key F5 then the 3 key to open the [Scan Entry] screen.2. If [Create] is not underlined, press the →, ↑ and Enter keys to underline it.3. With [Group Name] selected, enter a suitable group name.Note 1: 10 group names can be entered. If you attempt to enter more, the mes-sage "Scan group memory is full. Press any key to escape." appears. Press any key then delete unnecessary group names to enter new ones.Note 2: If the group name already exists, the message "Scan group by that name already exists. Press any key to escape." appears. Press any key and change the scan group name.4. Press the ↓ key to select [Ch Dwell Time]. Enter channel dwell time in seconds. Dwell time is the time in seconds the receiver waits on each channel in a scan group before it selects the next frequency.5. Press the ↓ key to select [(Receiving) Mode] then select the receiving mode;[AUTO], [ARQ] or [FEC].Note: [AUTO] is used to register a scanning channel group when both [ARQ] and [FEC] exist in the same Scanning Channel Group. When you select a scan group by the [Call Station] menu, the communication mode is controlled by the station entry’s mode.6. Press the ↓ key to select [Auto Search]. Select [ON] or [OFF].[ON]: The radio stops scanning when it finds the strongest signal (highest S/N ra-tio). To find the strongest signal, the radio scans all channels, which can take some time. Therefore, use this setting where the signal propagation is poor.[OFF]: The radio stops scanning on the first signal it finds. It is recommended to select [OFF] when the signal propagation is good.7. Press the ↓ key to select line No. 1 in the [Scanning Set Up] window.Group Name *: [Mode] for IB-583Press the  key to scroll the screen.
8. NBDP PREPARATIONS8-88. Enter the channel number (ITU or user channels) then press the → key to select [Scan].Note: If you enter an invalid channel, the message "Channel by that number does not exist. Press any key to escape." appears. Press any key then enter a valid channel.9. Press the ↓ key to select line No. 2. Enter a channel number.10. Enter other channel numbers then press the Enter key. A confirmation message appears.11. Press the Enter key again to save the data. The group name is displayed in the [Scanning Group List] window.12. To continue, press the Enter key twice then repeat steps 3 to 11.13. Press the Esc key to close the menu.Note 1: An ARQ from another station continues for 56 seconds. However, you cannot receive via ARQ if the number of registered scan frequencies multiplied by the channel dwell time is greater than 56 seconds.Note 2: The selective FEC mode requires authentication of call ID. However, you cannot receive via the selective FEC mode if the Call ID is not received with the frequency for scan detention time. If you might be called via the selective FEC mode, wait to receive the call on a single frequency, which you can set with the [Set Frequency] in the [Operate] menu.8.5.2 How to edit/delete scan channel groups1. Press the function key F5 then the 3 key to open the [Scan Entry] screen.2. Press the ↓ key to select scan group name from the [Scanning Group List].3. Press the → key then the ↓ key to select [Change] and press the Enter key.4. Press the ↓ key to place the cursor on the field (channel) to change.5. Do one of the following:Edit channels: Press the Backspace key to delete the channel number then enter a new channel number.Add channels: Enter a channel number on a blank line.Delete scan group: Delete the group name with the Backspace key.Disable channels temporarily: Press the ← key to underline [Pass].6. Press the Enter key twice.7. Press the Esc key to close the menu.8.6 How to Change the Window ColorYou can select and change the window color.IB-5831. Select [Change] from [Setup].2. Press the ↓ key to select [Window Color] then press the Enter key.Window Color Change Window Color SetupDefault ColorTo Change: ENTER To quit: ESC
8. NBDP PREPARATIONS8-93. With [Window Color Setup] selected, press the Enter key.4. Press the ← or → key to select the item to change: [BASE WINDOW], [BACK SCROLL], [EDIT 1-2], [FUNCTION], [SUB MENU 1-3], [MESSAGE].5. Press the ↓ key to select [Fore Color].6. Press the ← or → key to select color: [L-WHITE], [BLACK], [BLUE], [GREEN], [CY-AN], [RED], [MAGENTA], [BROWN], [WHITE], [GRAY], [L-BLUE], [L-GREEN], [L-CYAN], [L-RED], [L-MAGENTA], [YELLOW].7. Press the ↓ key to select [Back Color].8. Press the ← or → key to select color.9. Press the ↑ key to select [Window].10. Repeat the steps 4 to 9 to set other colors.11. Press the Enter key followed by the Esc key.IB-5851. Press the function key F6 to open the [System] menu.2. Press the → key to select [Change].3. Press the ↓ key to select [Window Color] then press the Enter key to open the [Window Color Edit] window.4. Press the ← or → key to select [1], [2] or [3]. The selected preset color is reflected on the [Window Color Edit] window. 5. Press the Enter key to reflect the selected preset color on the screen.If you want to reset or change the preset settings, do the following:1. Select [1], [2] or [3] then press the ↓ key.2. To reset the settings, press the Enter key with [Load Default] selected.To change the settings, press the ↓ key. Go to step 3.3. Press the ← or → key to select an option in [Window] and press the ↓ key.4. Press the ← or → key to select a color in [Fore Color] and press the ↓ key.5. Press the ← or → key to select a color in [Back Color] and press the ↓ key.Note: You cannot select the same color between [Fore Color] and [Back Color].6. To increase the brightness, press the F7 key while pressing and holding the Alt key. To decrease the brightness, press the F6 key while pressing and holding the Alt key. The changed brightness setting is underlined.7. To confirm the selections, press the Enter key. To cancel the selections, press the Esc key. The window closes.Window Color SetupWindow : [BASE WINDOW ] Fore Color : [L-WHITE ] Back Color : [BLUE ]To Change: ENTER To Change Value: L<=>RWindow Color EditTarget Preset 1 2 3Load DefaultEdit Color Window [ BASE WINDOW ] Fore Color [ BLACK ] Back Color [ WHITE ] Brightness 0 1 2 3 4 5 6 7 8 9 10To Change: ENTER To Change Value: L<=>R
8. NBDP PREPARATIONS8-10Default for each preset8.7 Screen Saver Function for IB-585Turn on or off the screen saver function for IB-585. When there are no operation for 10 minutes, the screen is black and "IB-585" appears at random.Note: This function is not available during standby and communication modes.1. Press the function key F4 then the 3 key to select [Screen Saver].2. Press the → key to select [ON].3. Press the Enter key to close the menu.Preset1 (original)Preset2(day)Preset3 (night)Brightness 10 10 5Base window Fore color L-White Black L-WhiteBack color Blue L-White BlackBack scroll Fore color L-White Black BlackBack color Blue White GrayEdit1 Fore color Black Black BlackBack color Green White GrayEdit2 Fore color Magenta Black WhiteBack color White L-Cyan BlueFunction Fore color Black Black L-WhiteBack color Cyan L-White BlackSub menu1 Fore color Black Blue L-CyanBack color White L-White BlackSub menu2 Fore color Blue Blue L-GreenBack color White White BlackSub menu3 Fore color White L-White L-MagentaBack color Black Blue BlackMessage Fore color White L-White WhiteBack color Magenta Blue Blue
9-19. NBDP FILE OPERATIONSThis chapter mainly describes how to create, save, open, edit and print files. The [Edit] menu provides a full lineup of editing facilities, including search and replace.9.1 How to Open and Close FilesTo create a telex message, you need to make a new file with the File Open command. When you open a new file, it is placed (opened) in one of two working areas. When both working areas are occupied, you must close a file to open a new file. This is done with the File Close command.How to open a file9.2 How to Create FilesThere are two modes for creating the files; for messages and for macros.• For messages: You can enter only the characters which are sendable in NBDP comminication. Press the function key F1 then the 1 key to create a message file.• For macros: You can enter only the characters ( ) which are used in a macro command. Press the function key F1 then the B key to create a macro file.1. Press the function key F1 to open the [File] menu.12Floppy Disk Memory or SD Card MemoryFile 1File 2File 3 Display Unit's Memory (Working area)One of two DisplaySwitchable. Select [Change Text] on the [Edit] menu.$ @ _ |*1*2*2*1: [Floppy Disk Format] for IB-583 *2: Only for IB-585
9. NBDP FILE OPERATIONS9-22. Press the 1 key to select [New]. The title bar shows [UNTITLED 1] or [UNTITLED 2]. The cursor marks the location where you can type text.3. Type your message.Note: Do not use the lower case letters, or the symbols #, &, *, $ and % in telex mes-sages. Also, do not put "$$$" in the middle of a TX message, but at the end. The com-munication line is automatically disconnected when this string is detected.To enter "$$$" when editing a message, press the Ctrl + Q keys for IB-585. For IB-583, enter "$$$" with using the $(4) key.9.3 How to Save a FileIB-583Use only 2HD type floppy disks. Insert the floppy disk with care. Rough handling can destroy the information stored inside. To eject the disk, press the Eject button on the left side of the floppy disk drive then remove the disk. Do not eject the disk while the operating lamp is lit, otherwise the contents of the disk can be damaged.IB-585Use SD cards 2GB or below, or SDHC cards 32GB or below. Insert or eject the SD card with care when the power is off. Rough handling can destroy the information stored inside. When ejecting the SD card with power-on, execute [Remove SD Card] in the [File] menu (see "Function key F1: [File] menu" on page 7-4) then remove the SD card.Note: When using the SD card after executing [Remove SD Card], remove the SD card then insert it.9.3.1 How to format floppy disks or SD cardsBefore you save a file to a floppy disk or an SD card, the disk or the card must be for-matted. Format the disk or the card as below.1. Press the function key F1 to open the [File] menu.2. Insert a new floppy disk or SD card in the drive.3. Press the 0 key to select [Floppy Disk Format] or [SD Card Format].4. Press the ↑ key to select [Yes] then press the Enter key. The screen shows for-matting progress as below. After formatting has been completed, control is re-turned to the standby screen.SD Card Format9% [Floppy Disk Format] for IB-583
9. NBDP FILE OPERATIONS9-39.3.2 How to save a file1. Press the function key F1 to open the [File] menu.2. Press the 3 key to select [Close]. The [Close Text] window appears.3. With [Yes] selected, press the Enter key.4. Enter the file name, using up to eight characters. You can use any alphabet or nu-meric on the keyboard. You can not use the symbols shown below. You can add an extension at the end of the file name, for example, .TXT, to distinguish text files from macro files.5. Press the Enter key.9.4 How to Edit Files9.4.1 How to cut and paste textYou can delete, move and copy text by using the [Cut], [Copy] and [Paste] functions in the [Edit] menu.| ! : " > < ;
9. NBDP FILE OPERATIONS9-4How to cut text1. Place the cursor on the first character of the text to cut.2. Highlight the text to cut by pressing and holding the Shift key while pressing the → key. If you highlighted the text which you do not want to cut by mistake, press the ← key to adjust the highlight.The highlight3. Press the function key F2 then the 2 key. Or press the Del key. The highlighted text is cut and the remaining text is reformatted.If you made a mistake, you can restore the text. Select [Undo] in the [Edit] menu.How to paste textTo paste the cut text to a new location, do the following:1. Place the cursor at the exact spot in the message where the cut text is to start.2. Press the function key F2 then the 4 key. Or press the Ins or Insert key.9.4.2 How to copy and paste textYou can copy a portion of text and paste it elsewhere.1. Select the text to copy (see "How to cut text" on page 9-4).2. Press the function key F2 then the 3 key. The text selected is copied to the paste buffer memory where the cut or copied text is stored. The screen returns to the normal screen.3. Place the cursor at the exact spot in the message where the copied text is to start.4. Press the function key F2 then the 4 key.9.4.3 Select allThe [Select All] feature lets you select all of the file currently displayed. This feature is useful when you want to combine the files. The procedure below explains how to place the file loaded in working area 1 onto the end of the file loaded in working area 2.1. Load the file to copy from a floppy disk or an SD card in working area 1.2. Press the function key F2 then the 5 key. The entire file appears in reverse video.3. Press the function key F2 then the 3 key. The file is placed in the paste buffer memory.4. Load the file to combine in working area 2.
9. NBDP FILE OPERATIONS9-55. Place the cursor at the exact spot in the message where the text now in the paste buffer memory is to start then press the Ins or Insert key.Copy and paste flow diagram9.4.4 How to search textThe [Search] feature lets you search for text in a forward or backward direction.1. Display a text and press the function key F2 then the 6 key. The [Search] window appears.2. Type the word to find.3. Press the → key.4. Press the ↑ or ↓ key to select [Forward] or [Backward] to search the file in a for-ward or backward direction respectively from the cursor position.5. Press the Enter key to begin the search.When the unit finds the word, the cursor stops at the first character of the word. Press the Enter key to continue the search. If the string could not be found, the message "Not Found (To quit: ESC)" appears. Press the Esc key to quit.9.4.5 How to replace textThe [Replace] feature helps you to replace a word or phrase with another word or phrase in a file.1. Press the function key F2 then the 7 key. The [Replace] window appears.2. Type a word to replace on the [Search string] line.1324Floppy Disk or SD cardWorking Area 1Working Area 2Paste Buffer MemoryOpen fileOpen fileTransfer (copy)Paste (Combine) Forward
9. NBDP FILE OPERATIONS9-63. Press the ↓ key to select [Replace with] then type a new word.4. Press the → key.5. Press the ↑ or ↓ key to select [Forward] or [Backward] to search the file in a for-ward or backward direction respectively from the cursor position.6. Press the → key.7. Press the ↑ or ↓ key to select whether you want to be queried or not each time the word is found.[Query]: Stop at each occurrence of the word to answer yes or no for replacement.[All]: Replace every occurrence of the word without confirmation.8. Press the Enter key to start the replacement.9.4.6 Goto lineThe [Goto Line] feature places the cursor at the head of a line desired.1. Press the function key F2 then the 0 key. The [Goto Line] window appears.2. Key in a line number then press the Enter key. The cursor shifts to the head of the line selected.9.4.7 Goto top, Goto bottomYou can easily go to the top or bottom line of a file. Press the function key F2 then the 8 key to go to the top line; press the function key F2 then the 9 key to go to the bottom line. Note that this feature can also be executed on the editor screen by pressing the Home or End key.9.5 How to Open FilesTwo working areas (called working area 1 and working area 2) are provided to which you can load a file, and one file can be displayed on the LCD.9.5.1 Open a file1. Insert the floppy disk or the SD card which contains the file to open.2. Press the function key F1 to open the [File] menu.
9. NBDP FILE OPERATIONS9-73. Press the 2 key. A list of files on the floppy disk or the SD card appears.4. Press the ↑ or ↓ key to select a file.5. Press the Enter key. The file appears and the title bar shows the file name. You can repeat this procedure to load another file into a working area.Note: When two working areas have been opened, the close confirmation window ap-pears. In this case, select [Yes] or [No] then press the Enter key to close an open file in order to open another file.9.5.2 Switch between filesTwo files can be opened and one file is displayed on the LCD. To switch between files, do the following:1. Press the function key F2.2. Press the A key to switch between the files.9.6 How to Rename FilesTo rename a file, do the following:1. Press the function key F1.2. Press the 5 key.3. Press the ↑ or ↓ key to select a file to rename then press the Enter key.4. Enter a new name.5. Press the Enter key.9.7 How to Save a File Under a New NameYou can save a file under a new name as follows:1. Open a file.2. Edit the file as necessary.
9. NBDP FILE OPERATIONS9-83. Press the function key F1.4. Press the 3 key to save the file.5. Press the Y key.6. Press the Backspace key to erase the original name then enter a new name.7. Press the Enter key.9.8 How to Delete FilesInsert the floppy disk or the SD card in the drive and do the following to delete unnec-essary files.1. Press the function key F1.2. Press the 4 key.3. Press the ↑ or ↓ key to select the file to delete then press the Enter key.4. Press the Enter key again. (To cancel, press the ↓ key to select [NO] then the En-ter key.)9.9 Real Time PrintingAn incoming or outgoing message can be printed out while it is being received or transmitted.1. Press the function key F1 to open the [File] menu.2. Press the 6 key to turn real time printing on or off.When the real time printing is on, "Print" appears in reverse video at the top of the screen. The sent messages are printed in bold face and the received messages are printed in normal type face.9.10 How to Print FilesYou can print files stored on the floppy disks or the SD cards as follows:1. Press the function key F1.2. Press the 7 key.3. Press the ↑ or ↓ key to select a file then press the Enter key.4. Press the Y key.To stop printing at any time, press the function key F1 then the 8 key. If the file could not be printed, the message "Cannot print. Check connection between printer and ter-minal. Press any key to escape." is displayed.
10-110. NBDP TRANSMISSION,RECEPTIONThis chapter mainly shows you how to transmit and receive telex messages.10.1 Manual CallingThe simplest way to communicate with a telex subscriber is manual calling. For the ARQ mode, you can display beforehand the message to send, or type your message manually.1. Press the function key F3 to open the [Operate] menu.2. For IB-583:Press the 9 key to select [Set Frequency].Before calling, watch the intended TX frequency carefully to confirm that is unoccupied.NOTICE1: Call Station3: File to Send4: Cancel Sending5: Scan (Start/Stop)6: Manual Reception7: Timer Operation8: Manual Calling9: Set FrequencyOperate2: Macro Operation 1: Call Station3: File to Send4: Cancel Sending5: Scan (Start/Stop)6: Manual Reception7: Timer Operation8: Manual Calling9: Set Frequency0: Set ChannelOperate2: Macro Operation For IB-583For IB-585

Navigation menu