User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2869488 |
| Application ID | 8ZF68iGQhzMcut38qjPc/A== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 67.96kB (849480 bits) |
| Date Submitted | 2016-01-12 00:00:00 |
| Date Available | 2016-01-12 00:00:00 |
| Creation Date | 2015-11-12 15:26:20 |
| Producing Software | Adobe PDF Library 11.0 |
| Document Lastmod | 2015-11-12 15:27:34 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC (Windows) |
1M23N31002 R7006SB ◆ FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz ◆ S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver Thank you for purchasing a Futaba R7006SB FASSTest-2.4GHz compatible receiver. The R7006SB receiver features bi-directional communication with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output ports (1-6ch) and S.BUS output ports. The R7006SB can also be switched the FASST(Multi-ch/7-ch) System. ● Applicable systems: Futaba FASSTest-2.4GHz / FASST (Multi-ch,7ch) -2.4GHz system transmitter ■ The R7006SB has two antennas. In order to maximize signal reception and promote safe modeling Futaba has adopted a diversity antenna system. This allows the receiver to obtain RF signals on both antennas and fly problem-free. Usage precaution • Analog servos cannot be used with the R7006SB in the FASSTest 12CH / FASST High-speed mode. WARNING Antenna installation for carbon fuselage Changes or modification not especially approved by the party responsible for compliance could void the user’ s authority to operate the equipment. The R7006SB receiver should be protected from vibration by foam rubber, Velcro, or similar mounting methods. Protect from moisture. Keep away from conductive materials to avoid short circuits. Be careful of connector insertion Don't connect an S.BUS servo / gyro to S.BUS2 connector. Link precaution Antenna installation precaution Do not perform the linking procedure while the motor's main power connected or the engine is operating as it may result in serious injury. Do not cut or bundle the receiver antenna wire. Do not bend the coaxial cable. It causes damage. The antennas must be mounted in such a way to assure they are strain relieved. Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can. Be sure that the two antennas are placed at 90 degrees to each other. Compliance Information Statement (for U.S.A.) When the linking is complete, please cycle the receiver power and ensure the receiver is properly linked to the transmitter. Please power up your system in this order. Transmitter first, followed by the receiver. If the R7006SB receiver was previously linked to another transmitter, make sure that transmitter is not operating while linking the receiver to the new transmitter. Servo for conventional system Antenna installation S.BUS Gyros S.BUS servos 90˚ This device, trade name Futaba Corporation, model number R7006SB, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. (3) This module meets the requirements for a mobile device that may be used at separation distances of more than 20cm from human body. To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting device. The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc. com (Support) You must leave 30mm at the tip of the antenna fully exposed. The exposed antenna should be secured so that it cannot move around or back inside of your aircraft. Channel 1-6 Hub Telemetry sensor S.BUS Port (SB) Telemetry sensor S.BUS2 Port (SB2) R7006SB The receiver power supply can be connected to any port. Hub S.BUS2equipment When all ports are used. Servo Y-harness Switch Link LED Link/Mode switch System Mode LED FASSTest Green Solid Mode LED R7006SB Specifications FASSTest-2.4GHz system(18ch/12ch mode) FASST-2.4GHz system (Multi-ch/7ch mode) S.BUS2 and S.BUS port and 6ch for conventional system receiver • Dual antenna diversity • Size: 0.89 x 1.5 x 0.48 in. (22.5x38.1x12.2mm) • Weight: 0.28 oz. (8g) • Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V) • Battery F/S Voltage: FASSTest---It sets up with a transmitter FASST---3.8V FASST FASSTest FASST Off LED Indication Status No signal reception Receiving signals Waiting for link No signal reception Receiving signals Receiving signals but ID is unmatched Waiting for link Unrecoverable error (EEPROM, etc.) Battery 3.7 ～ 7.4V Link LED Red Solid Green Solid Start → 2second later → Red Blink （1second） Red Solid Green Solid Green Blink Red Blink Alternate blink *When on "FASST-7ch" mode, the fail safe function can be set for 3-channel only. *Be sure that when using ESCs regulated output the capacity of the ESC must meet your usage condition. *Never use dry batteries for the power supply of the R7006SB as they may cause difficulties. Channel Modes The R7006SB is capable of changing its channel allocations as described in the table below. This is especially important when using the receiver in a dual receiver mode. See your transmitter operation manual for complete details on operating in the dual receiver mode. Turn on the receiver. [Transmitter is always OFF] Press and hold the Mode/Link button for 5 seconds to 10 seconds. When the LED of the receiver changes from blinking red to blinking red with green, Mode/Link button is released. 4 The LED should now be blinking red in 2 times of the patterns described by the chart below. Each press of the Mode/Link button advances the receiver to the next mode. 6 When you reach the mode that you wish to operate in, press and hold the Mode/Link button for more than 2 seconds. When LED blinks in green with red, it is the completion of a mode change, Mode/Link button is released. Please cycle the receiver power off and back on again after changing the Channel mode. R7006SB CH Mode table Output connector 5/SB 6/SB2 Red LED blink Mode Ａ 1 time Channel Mode B S.BUS S.BUS2 2 times Mode C S.BUS2 3 times Mode D 10 11 12 S.BUS S.BUS2 4 times Default Systems (FASSTest ⇔ FASST) change method 1 Turn on the receiver. [Transmitter is always OFF] 2 Press and hold the Link/Mode button for more then 10 seconds. 3 When the LED begins to blink green the button may be released. 4 The LED should now be blinking green in one of the patterns described by the chart below. ( Default : FASSTest ) 5 Each press of the Mode/Link button advances the receiver to the next system. 6 When you reach the system that you wish to operate in, press and hold the Mode/Link button for more than 2 seconds. When LED blinks in green with red, it is the completion of a system change, Mode/Link button is released. 7 Please cycle the receiver power off and back on again after changing the system. Green LED blink 1 time 2 times 3 times 4 times 5 times R7006SB System table System Default FASSTest FASST Multi-ch Normal mode FASST Multi-ch High-speed mode FASST 7ch Normal mode FASST 7ch High-speed mode *The telemetry cannot be used with the FASST system. 本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文規定 1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加 大功率或變更原設計之特性及功能。 2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率 射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 FASSTest FASSTest is a bidirectional communication system between the R7006SB receiver and FASSTest capable transmitters. Multiple optional telemetry sensors may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter. Link to the transmitter : FASSTest Bring the transmitter and the receiver close to each other, within 20 inches (half meter). 2 Turn on the transmitter. linking mode. Place the transmitter into the receiver 3 Turn on the receiver. 4 The receiver will wait for the linking process to begin for 2 seconds. Following that it will return to the normal operation mode. 5 When the LED of the receiver changes from blinking red to solid green, linking is complete. (A link waiting state is ended in 1 second.) • Refer to the transmitters operation manual for complete details on how to place the transmitter into the linking mode. • If there are many FASSTest systems turned on in close proximity, your receiver might have difficulty establishing a link to your transmitter. This is a rare occurrence. However, should another FASSTest transmitter/receiver be linking at the same time, your receiver could link to the wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid the problem,we strongly recommend you to double check whether your receiver is really under control by your transmitter. • If the System Type of the transmitter is changed, the receiver will need to be re-linked to the transmitter. S.BUS2 S.BUS2 extends S.BUS and supports bidirectional communication. Sensors are connected to the S.BUS2 port. Link to the TMA-1 Telemetry Adapter 1 R7006SB has to be FASSTest. 2 First, a transmitter and a receiver are linked. 3 Transmitter is turned off. 4 Press and hold the Mode/Link button of R7006SB for 15 seconds. 5 When LED of R7006SB, Red Blink → Red with green Blink → Green Blink → Red Blink → Mode/Link button is released. 6 R7006SB was link mode with TMA-1. The LED blinks in green with red of R7006SB. 7 The link button of TMA-1 is pushed for a long time to LED blink. 8 Completion of a link will change LED of TMA-1 green from red only for a moment. 9 Please cycle the receiver power. FASST When switched, the R7006SB can use the FASST-Multi/7ch mode. When the FASST system is used, the telemetry cannot be used. The FASST system has a Normal mode and a High-speed mode. However, in the High-speed mode, analog servos cannot be used. Link to the transmitter : FASST Bring the transmitter and the receiver close to each other, within 20 inches (half meter). 2 Turn on the transmitter and receiver. 3 Link operation is performed by the Link/Mode switch. • When using TM-8 module, it's possible to set F/S position (only 3CH). 0 sec. Press and Hold time With TM-8 (not included in this set) 1 sec. 0 to 1 sec. No function Besides TM-8 2 sec. 1 to 2 sec. More than 2 sec. To set the F/S Re-link(ID set) and to position(No re-link) set the F/S position No function Re-link(ID set) *Refer to the instruction manual of the transmitter or module used for a description of the linking operation, F/S position setting methods and other details. FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 ©FUTABA CORPORATION 2015, 11 (1)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2015:11:12 15:26:20+09:00 Creator : Adobe InDesign CC (Windows) Modify Date : 2015:11:12 15:27:34+09:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2015:11:12 15:27:34+09:00 Creator Tool : Adobe InDesign CC (Windows) Instance ID : uuid:47a2cde9-b247-497f-9657-3bb4c3b5af19 Original Document ID : adobe:docid:indd:a388b311-cabe-11df-aedc-968d4bca4a31 Document ID : xmp.id:f5d09aae-1cbd-3042-951a-443555c56b84 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:392ae5bb-7003-3a40-b6d6-e813ce78efb9 Derived From Document ID : xmp.did:ceacd901-e25a-f542-969d-0814d39fce70 Derived From Original Document ID: adobe:docid:indd:a388b311-cabe-11df-aedc-968d4bca4a31 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Windows) History Changed : / History When : 2015:11:12 15:26:20+09:00 Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 2EXIF Metadata provided by EXIF.tools