Futaba T6K-24G Radio Control User Manual MANUAL 6K E 0521

Download:
Mirror Download [FCC.gov]
Document ID	2668325
Application ID	64irsWq143legyBTW6YIZQ==
Document Description	User Manual-Part II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	302.34kB (3779226 bits)
Date Submitted	2015-07-06 00:00:00
Date Available	2015-07-07 00:00:00
Creation Date	2015-06-25 17:20:16
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2015-06-25 17:22:39
Document Title	MANUAL_6K(E)_0521.pdf
Document Author:	minchih

Various telemetry sensors (optional) information display and alarm setting
Various telemetry sensors (sold separately) are connectable to the S.BUS2 port of the R3006SB through
a 3-way hub and relay terminals. The information of sensors connected at initialization can be viewed as
long as 2 or more of the same kind of sensor are not used (for example, 2 temperature sensors).
● Sensors that can be used with the T6K: Futaba SBS-01T, SBS-01RM, SBS-01RO, SBS-01A
● Robbe sensors that can be used with the T6K: Robbe TEMP125, VARIO-1712, VARIO-1672 (Setting change is needed in a
SENSOR screen.)
*Futaba does not sell Robbe sensor.
Sensor Connection
6%86 6%%
&RQQHFWRU
7(036HQVRU
6%677(
530‫ق‬PDJQHW‫ك‬6HQVRU
6%650 5%
530‫ق‬RSWLFV‫ك‬6HQVRU
6%652
+8%
5HIHUWRWKHPDQXDORIHDFKVHQVRUIRUWKH
PRXQWLQJLQVWUXFWLRQWRWKHPRGHORIVHQVRU
Method
Sensor information can be viewed by calling telemetry from the menu and calling the connected
sensor display page. The detailed setting screen of that sensor can be called by selecting and
pressing the sensor you want to select with the Jog key.
Common function
$OWLWXGH6HQVRU
6%6$
+8%
● Refer to the receiver battery (RX-BATT) item for a description of key operation.
① Select "TELEMETRY" from the
menu with the Jog key.
② The sensor item of your choice
is chosen by Jog key, and Jog
key is pressed.
Sensor set up
81
TEMP : Display of SBS-01T/TE(Option), and alarm setup
*A temperature sensor must be installed in the aircraft.
● Conversion of a display unit is performed by "TELEMETRY
UNIT" of "PARAMETER".
TEMP is a screen which displays/sets up
the temperature information from an optional
temperature sensor.
The temperature of the model (engine, motor,
   #      
         
alarm and/or vibration will ALARM you.
%\'Z[] '^V^Z^'_    
   
        X 
J
'/ 
' / //  ///
   ?W 

Z // ///date reset
by pressing the Jog key for 1 second.
 `{[`
   
 /     
 /   
    
Common function
"VIB" type
If the following types are selected, the
transmitter will vibrate during the warning.
`zW`
  
 /     
     /       
       
 
TYPE 1
TYPE 2
TYPE 3
 _          
/      
      #
     % 
! 
%   
OFF
OFF
OFF
ON
ON
2 Position
82
3 Position
ALARM set : Hot warning
D@   = D!P    !   #
|Z     {[}&QVQZ*/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  }|℃
 Q@ /  };~℃ ‚~℃
&{[}&V+Z+'*≧zW}&V+Z+'**
|Z     zW}&QV^Z*/
~% Q'/   ;J
<Z     zW}&V+Z+'*\ ]/
€Q@     ;J
 +  }℃
 Q@ /  };~℃ ‚~℃
&{[}&V+Z+'*≧zW}&V+Z+'**
*When the + - key simultaneous press, the rate is reset to the
initial value.
*When the + - key simultaneous press, the rate is reset to the
initial value.
&'  /          
    #   ^WzJ*
&'  /          
    #   ^WzJ*
R.P.M : Display of SBS-01RM/RO/RB(Option), and alarm setup
*A RPM sensor must be installed in the aircraft.
RPM is a screen which displays / sets up the
RPM information from an optional RPM sensor.
The RPM of the model (engine, motor, etc.)
     
         
alarm and/or vibration will ALARM you.
%\[Z] '^V^Z^'_ 
     

   X J
 '   /   /  /    
  ?W 

  Z   /  /  dat e r e s e t b y
[Z
pressing the Jog key for 1
second.
{[} +      
 /     
  [Z     
   
"VIB" type
If the following types are selected, the
transmitter will vibrate during the warning.
TYPE 1
zW}+    
 /     
  [Z !    
   
TYPE 3
`ZQƒ&ZQƒW^'+*` `?['
&?['+QV*`     
      
+ `?['+QV`#   / !
  &`+W`* !  & 
 * /  
%„%;|Z}ZQƒW^'+
%„%;|?}?['+QV
+ `ZQƒW^'+`#       
!     &/  *   
   
%   
OFF
OFF
Common function
 _          
[Z      
 
 
    #
Q   % 
! 
TYPE 2
OFF
ON
2 Position
ON
3 Position
D@   = *    
ALARM set : Under rotations
|Z     {[}QVQZ/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  }~/
 Q@ /  }/‚< #/
&{[}&V+Z+'*≧zW}&V+Z+'**
|Z     zW}QVQZ/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  }/
 Q@ /  }/‚< #/
&{[}&V+Z+'*≧zW}&V+Z+'**
*When the + - key simultaneous press, the rate is reset to the
initial value.
*When the + - key simultaneous press, the rate is reset to the
initial value.
&'  /          
    #   ^WzJ*
&'  /          
    #   ^WzJ*
83
ALTITUDE : Display of SBS-01A (Option), and alarm setup
*An altitude sensor must be installed in the aircraft.
@**]$^     ) 
the altitude information from an optional altitude
   %&  *        
         
(low) than preset altitude, you can be told by alarm.
To show warning by vibration can also be chosen.
$        <
m, and it displays the altitude which changed from
there. Even if the altitude of an airfield is high,
that shall be 0 m and the altitude difference from
 ,   *      
altitude from atmospheric pressure. Atmospheric
pressure will get lower as you go up in altitude,
using this the sensor will estimate the altitude.
Please understand that an exact advanced display
cannot be performed if atmospheric pressure
changes in a weather situation.
● Conversion of a display unit is performed by "TELEMETRY
UNIT" of "PARAMETER".
'  / //    ///
   ?W 

 Z //  ///    
   Jog key! |  
% \QV'+'{z^]    '^V^Z^'_    
   
   X J
Q
$/7,78'(
P
 ` { [ `          
 /      0,10$;

        $/$50  9,%  /,0,7
    
83㌣,1+㌣2))㌣岜
Common function
'1㌣,1+㌣2))㌣
 ` z W `            5()(5(1&(㌣(;(&
 /      63((&+㌣,1+6:㌣18//
      
    
%   
 _          
Q      
 
    #
Q   % 
! 
& "   
       Q
|'  /     /       
      
~Z     \^^^W^] !`^†^`
/
<[  X J&|  /  *
*Atmospheric pressure is changed according to the weather also
 
 , }       
ALARM set : High side
|Z     {[}&QVQZ*/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  }~&/*
 Q@ /  };‡‚‡&/*
&{[}&V+Z+'*≧zW}&V+Z+'**
*When the + - key simultaneous press, the rate is reset to the
initial value.
&'  /          
    #   ^WzJ*
84
"VIB" type
If the following types are selected, the
transmitter will vibrate during the warning.
OFF
TYPE 1
TYPE 2
TYPE 3
OFF
OFF
ON
ON
2 Position
3 Position
ALARM set : Low side
|Z     zW}&QVQZ*/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  };‡&/*
 Q@ /  };‡‚‡&/*
&{[}&V+Z+'*≧zW}&V+Z+'**
*When the + - key simultaneous press, the rate is reset to the
initial value.
&'  /          
    #   ^WzJ*
VARIO : Display of SBS-01A (Option), and alarm setup
*An altitude sensor must be installed in the aircraft.
● Conversion of a display unit is performed by "TELEMETRY
UNIT" of "PARAMETER".
†W5     )  
variometer information from an optional altitude
sensor.
*          
be known.
         
alarm and/or vibration will ALARM you.
'  / //    ///
   ?W 

Z // ///date reset by
pressing the Jog key for 1 second.
%\>Q+?] '^V^Z^'_     
 
   X J
>  /
9$5,2
PV
`{[`     /
               0,10$;

          $/$50  9,%  /,0,7
   
83㌣,1+㌣2))㌣岜
"VIB" type
If the following types are selected, the
transmitter will vibrate during the warning.
 _          
>          
 
    #
Q   % 
! 
OFF
TYPE 1
TYPE 2
TYPE 3
OFF
OFF
ON
ON
2 Position
3 Position
ALARM set : Rise side
ALARM set : Low side
|Z     {[}&QVQZ*/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  }‡&/$ *
 Q@ /  };|‡‚|‡&/$ *
&{[}&V+Z+'*≧zW}&V+Z+'**
|Z     zW}&QVQZ*/
~% Q'/   ;J
<Z     {[}&V+Z+'*\ ]/
€Q@     ;J
 +  };‡&/$ *
 Q@ /  };|‡‚|‡&/$ *
&{[}&V+Z+'*≧zW}&V+Z+'**
*When the + - key simultaneous press, the rate is reset to the
initial value.
*When the + - key simultaneous press, the rate is reset to the
initial value.
&'  /          
    #   ^WzJ*
&'  /          
    #   ^WzJ*
Common function
'1㌣,1+㌣2))㌣
 ` z W `            
 /      63((&+㌣,1+6:㌣18//
        
    
%   
85
SENSOR Sensor
(Common)
Function
When using sensor to which the slot number
was changed by other transmitters or Robbe sensor
"*^7%?=9 †W5(?E?= ?BE=#     
registered here.
This screen registers the telemetry sensors used
with the transmitter. When Futaba SBS-01T/E,
SBA-01RO/RM/RB and SBS-01A sensor is used,
this setting is unnecessary and the sensor can be
used by simply connecting it to the S.BUS2 port of
the receiver.
[What is a slot?]
&    , 'sensors   ,   "slot". There are slots
from No. 1 to No. 31. Altitude sensors units may use  .
T6K can use 1 of temperature, RPM and altitude sensor respectively. Any more sensor can't
be used.
Method
Calling the setting screen
Common function
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "SENSOR"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
Change the sensor
① In the SENSOR screen state, select
(sensor) from the menu with the
Jog key.
② Select the sensor by pressing
the + key or ‒ key.
＋
● The "SENSOR" of a menu is chosen, and Jog key
press.
or
−
● The kind of sensors.
● SBS-01T, SBS-01TE is used.
● SBS-01RO, SBS-01RM, SBS-01RB is used.
● OFF → R3008SB：EXT battery voltage can be indicated.
● R3008SB Receiver, CA-RVIN-700 (external voltage input cable sold
separately) is necessary.
● Soldered wiring work is necessary.
86
● REGISTER（When using sensor to which the slot number was changed by other transmitters.）
This function resets a starting slot of a sensor and registers with a transmitter.
'      ,       
Sensor connect
Receiver battery
Hub
Sensor
Connect a sensor to add
T10J
Method
Calling the setting screen
＋
② Select "SENSOR"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
Common function
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
（1 second）
④ Jog key presses side
and makes it 6pages.
Left 1-time
press
Sensor register
① "REGISTER" in SENSOR SLOT page
2 is chosen by Jog key.
② Press the Jog key for 1 second.
● Confirmation message
"sure?" blinks.
③ Press the Jog key.
● A confirmation "beep"
sounds when complete.
● "COMU-ERROR" : When the number of slots
needed in registration is insufficient, an error is
displayed and registration cannot be performed.
87
S.BUS
S.BUS servo link
(Common)
Function
An S.BUS(2) servo can memorize the channel
and various settings you input. Servo setting can
be performed on the T6K screen by wiring the
    , 
* With some S.BUS(2) servos, there are some functions with
                  
screen will change. (Only the function which can be used by
a servo is displayed.)
’         , 
if a stick is moved, the test of operation of the servo can be
operated and carried out.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "S.BUS"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
Common function
④ Connect a S.BUS servo to
set up.
Receiver battery
HUB
S.BUS/
S.BUS Servo setting
⑤ "READ" is chosen by Jog key, Press
the Jog key for 1 second.
S.BUS2 Servo
T6K
⑥ READ is completed and
the item in which data of
S.BUS servo and a setup
are possible is displayed.
* "COMU-ERROR" :
It is failure of READ. Check a
servo and connection.
⑦ S.BUS servo is set up.
⑧ "WRITE" is chosen and Jog key
is pressed for 1 second.
The writing is done when
"COMPLETE" is shown.
Next page S.BUS servo function
88
S.BUS Servo Description of function of each parameter
*There are a function which can be used according to the kind of servo, and an impossible
function.
ID =
[ ID ]
Displays the ID of the servo whose parameters are to be read. It cannot be changed.
CHAN ▶
[ Channel ]
Channel of the S.BUS system assigned to the servo. Always assign a channel before use.
NEUT ▶
[ Neutral Offset ]
EPA ▶
[ Travel Adjust ]
The left and right travels centered about the neutral position can be set independently.
DEAD ▶
[ Dead band ]
The dead band angle at stopping can be specied.
[Relationship between dead band set value and servo operation]
Common function
The neutral position can be changed. When the neutral offset is large value, the servo's range
of travel is restricted on one side.
Small ÂŚ Dead band angle is small and the servo is immediately operated by a small signal
change.
Large ÂŚ Dead band angle is large and the servo does not operate at small signal changes.
(Note) If the dead band angle is too small, the servo will operate continuously and the
current consumption will increase and the life of the servo will be shortened.
REVE ▶
[ Reverse ]
The direction in which the servo rotates can be changed.
STRE ▶
[ Stretcher ]
The servo hold characteristic can be set. The torque which attempts to return the servo to the
target position when the current servo position has deviated from the target position can be
adjusted.
This is used when stopping hunting, etc., but the holding characteristic changes as shown
below.
[Relationship between stretcher and servo operation]
Small ÂŚ Servo holding force becomes weaker.
Large ÂŚ Servo holding force becomes stronger.
(Note) When this parameter is large, the current consumption increases.
89
BOST ▶
[ Boost ]
The minimum current applied to the internal motor when starting the servo can be set. Since
a small travel does not start the motor, it essentially feels like the dead band was expanded.
The motor can be immediately started by adjusting the minimum current which can start the
motor.
[Relationship between boost set value and servo operation]
Small ÂŚ Motor reacts to a minute current and operation becomes smooth.
Large ÂŚ Initial response improves and output torque increases. However, if the torque is too
large, operation will become rough.
DAMP ▶
[ Damper ]
The characteristic when the servo is stopped can be set.
When smaller than the standard value, the characteristic becomes an overshoot
characteristic. If the value is larger than the standard value, the brake is applied before the
stop position.
Common function
Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting
may occur, depending on the conditions. If hunting (phenomena which cause the servo
to oscillate) occurs even though the Dead Band, Stretcher, Boost and other parameters are
suitable, adjust this parameter to a value larger than the initial value.
[Relationship between damper set value and servo operation]
Small ÂŚ When you want to overshoot. Set so that hunting does not occur.
Large ÂŚ When you want to operate so that braking is not applied. However, it will feel like
the servo response has worsened.
(Note) If used in the hunting state, not only will the current consumption increase, but the
life of the servo will also be shortened.
BSTM ▶ ON/OFF
[ Boost ON/OFF ]
OFF : It is the boost ON at the time of low-speed operation.(In the case of usual)
ON : It is always the boost ON.(When quick operation is hope)
SPED ▶
[ Speed Control ]
Speeds can be matched by specifying the operating speed. The speed of multiple servos can
be matched without being affected by motor fluctuations. This is effective for load torques
below the maximum torque.
However, note that the maximum speed will not be exceed what the servo is capable of even
if the servos operating voltage is increased.
STAR ▶
[ Soft Start ]
Restricts operation in the specied direction the instant the power is turned on. By using this
setting, the rst initial movement when the power is turned on slowly moves the servo to the
specied position.
SMOT ▶
[ Smoother ]
This function changes smoothness of the servo operation relative to stick movement
changes. Smooth setting is used for normal flight. Select the "OFF" mode when quick
operation is necessary such as 3D.
90
M TRANS Model transfer
(Common)
Function
TRANSFER
RECEIVE
Transmission of model data is possible with T6K
   $        * 
7$@(*W>&           
you are using in the transmitter. As for the receiving
transmitter, any data on the current model that is receiving
the information will be over-written.
Model Data
*T6K does not carry out normal operation during data transfer.
T6K-1
Method
T6K-2
Calling the setting screen
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "M TRANS"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
Execution of transmission/
reception
Model transfer
● MDL-TRANS between two T6K radios should be performed within
① In each T6K, the ＋ or − key is pressed and it is
made "TRANSFER" and "RECEIVE".
＋
Common function
MODE：
T R A N S F E RT6K o f d a t a
origin ）
／
RECEIVE
T6K which receives
data）
2-meter range.
② Select "Execute" with the Jog key.
−
or
● "TRANSFER"：T6K of data origin
"RECEIVE"：T6K which receives data
Selection range：TRANSFER, RECEIVE
CAUTION
③ Hold down the Jog key [ each T6K ].
1 second )
）
● "COMPLETE" is displayed and the mode
transfer is nished.
● If data is not being transmitted, the receiving transmitter
returns to normal operation 10 seconds after execution. At
this time, "Failure" (not transmitting) is displayed.
!  " <        
#" 
       
      "< 
    Q
NOTE: 7$@(*W>&     *BŠ    
be performed within a 2-meter range.
91
Timer
TIMER
(Common)
Function
The timer is convenient during a competition to
   ,     
on a full tank of fuel.
'  /      !     /  %  
/    /   / #   
    / /    
'   ! /     ! / /  
 &{[*#   &z?W*#      &zW;%'[*
' /  ! /    
/      '  / 
  ! /  /  /  
/          '     
/      ^  /  
  / ‡    
%   Q   z#    J &%';'*#   
  &[;%*         $
    &?W;%* '  ?W$?    
   #      
# /         
 
  /       
 X J  X J  ! |  
  / # /  %  Q 
z       &%;%*' 
?W$?     
'  $  /   /     
/   #    
 ~      ! / ~    !   
/#        |  
 ! /|   !   /
Method
Common function
Calling the setting screen
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "TIMER"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
● When the throttle switch is
● Select the item with the
Jog key.
Time set up
Mode selection
ON Switch selection
Reset Switch selection
Switch direction
selected at switch selection,
hold the throttle stick in the
position you want to set the
ON/OFF point at ON direction
setting and set the ON/OFF
position by pressing the Jog key
for 1 second. The timer is turned
ON at points higher than this
position. The ON direction can
be switched by pressing the +
key or ‒ key.
Timer
■ Mode selection
① Select timer mode
from the "MODE"
with the ＋ or − key.
＋
−
or
（Range）
UP, DOWN, DN-STP
92
■ Timer time setting
■ Switch selection and ON direction setting
② Set the time by
pressing the + key or
‒ key at each TIME
(minutes):(second)
item.
③ Select the switch by pressing the + key or ‒ key at the
START or RESET item and set the ON direction by pressing
the + key or ‒ key at the ON direction setting item.
(Switch setting range)
START: SwA ∟ D, THR, PWR
RESET: SwA ∟ D
(Switch ON direction)
3P SW: NULL (normally off), UP, UP&D, UP&C, CNTR, C&DN,
DOWN
2P SW: NULL, UP, DOWN
（Range）
0 ∟ 99 m i n u t e s 59
seconds
Displaying the timer on the home screen
The set timer can be displayed on the home screen. (When a user name is not set, the Futaba logo is
displayed.) When the home screen display is changed to timer by PARAMETER, the set timer is displayed.
Calling the setting screen
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "PRMTR"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
② Select "TIMER" by pressing
the + key or ‒ key.
③ End setting by pressing the
END key.
（1 second）
① Select "HOME-DSP" from the
parameter 2 page with the Jog key.
＋
−
END
Common function
Parameter
93
TRAINR Trainer
(Common)
Function
&                  ,   
to match the student’s level.
The trainer function can be used by connecting the instructor’s transmitter to the student’s transmitter
     "    #&       
the student enters a dangerous situation, control can be immediately switched to the instructor.
● Four operation modes can be selected at each channel.
● The trainer switch is set to switch D.
Trainer code
When the trainer function is used, cancel the function
assigned to the switch D. THR-HOLD of a helicopter can't
be used.
Teacher
Student
CAUTION
Use the trainer function under the following conditions:
Common function
● When the instructor uses a T6K transmitter, set the student s transmitter modulation to PPM (for
conventional frequency transmitter). (When the student uses a T6K transmitter, the modulation
mode does not have to be changed. A PPM signal is always output from the trainer jack.)
● Before flight always confirm that all the instructor and student channels operate normally as set.
● Always insert the trainer cord as far as it will go and take measures so that the cord will not work
loose during use.
● Always remove the high frequency module of the student s transmitter. (For module type)
● Never turn on the student s transmitter power switch.
Trainer function operation modes
● FNC mode: The channel set to this mode can be controlled by the student using the mixing set at
the instructor s transmitter. *Student settings are returned to their initial value in advance. Next,
reverse function makes all channels normal.
● NOR mode: The channel set to this mode is controlled by signals from the student s transmitter. (The
instructor and student settings must be the same.)
● OFF mode: The channel set to this mode cannot be controlled by the student. It can only be controlled
by the instructor.
However, channels not provided at the student s transmitter are controlled by the instructor regardless of the above
settings.
When other models are selected, the trainer function is deactivated, but the channel settings remain.
Example of use
● When the FUNC mode is set at the stick channel, helicopter stick operation training is possible even
with a 4EX transmitter (4 channels for aircraft).
● Control by the instructor is possible by setting only the training channel matched to the student s
level to the NORM mode and setting the other channels to the OFF mode.
◆ Trainer Cords
Instructor
Student
Trainer Cords
T12FG (FUTM4405)
6K
10C, 9C, 7C, 6EX, 4EX
18MZ, 18SZ, 14MZ,
14SG, FX-22, 12Z,
12FG, 8FG, 6K, 8J, 6J
18MZ, 18SZ,
14MZ, 14SG, FX22, 12Z, 12FG,
8FG, 10C, 9C, 7C,
8J, 6J, 4EX
94
6K
T12FG (FUTM4405) and 9C
(FUTM4415) Trainer Cords
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the + key
for 1 second.
＋
② Select "TRAINR"
from the menu with the Jog
key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
（Trainer function）
● Select the item with the
Jog key.
● If a trainer cable was
connected, it indicates "ON
LINE".
Function activation
Channel Select
● Channel setting mode display
AIRPLANE (2AIL1FLP)
1: AI1（Aileron1）
2: ELE（Elevator）
3: THR（Throttle）
4: RUD（Rudder）
5: FLP（Flap）
6: AI6（Aileron6）
HELICOPTER
1: AIL（Aileron）
2: ELE（Elevator）
3: THR（Throttle）
4: RUD（Rudder）
5: GYR（Gyro）
6: PIT（Pitch）
GLIDER (2AIL2FLP)
1: AI1（Aileron1）
2: ELE（Elevator）
3: FL3（Flap3）
4: RUD（Rudder）
5: FL5（Flap5）
6: AI6（Aileron6）
MULTICOPTER
1: AIL（Aileron）
2: ELE（Elevator）
3: THR（Throttle）
4: RUD（Rudder）
5: AUX
6: MOD（Mode）
Trainer function
■ Function activation
① Select the "OFF" by
pressing the + key
or ‒ key.
＋
−
or
● When you do not want to use the
function select INH.
■ Mode setting
② The mode of the channel of hope
is chosen by pressing the + key
or ‒ key.
−
or
Selection range：OFF,
NOR, FNC
When the switch D of
teacher's transmitter
is turned off, it'll be
teacher's control.
When the switch D of
teacher's transmitter
is turned on at the
front, it'll be student's
control.
嵉崳嵍
嵤岜岜
岜岜

㌣崮

嵔

㌣崣 嵉崰嵒嵤
嵛
㌣6% 崝嵤
㌣'
5
㌣嵊
㌣崣 (;3
ĺ´Ż ĺ´Łĺ´Ť
嵛崧嵤 2
㌣崰 嵓崰嵑嵛 崮崌
嵔
ĺ´Ą
崊嵑嵤
㌣崠 嵤崲嵤
很
嵋崌嵕
崣嵛崡
＋
Common function
● Select CH mode Display
＜ ChannelDisplay ＞
嵉崳嵍
嵤岜岜
岜岜

㌣崮

嵔

㌣崣 嵉崰嵒嵤
嵛
㌣6% 崝嵤
㌣'
5
㌣嵊
㌣崣 (;3
ĺ´Ż ĺ´Łĺ´Ť
嵛崧嵤 2
㌣崰 嵓崰嵑嵛 崮崌
嵔
ĺ´Ą
崊嵑嵤
㌣崠 嵤崲嵤
很
嵋崌嵕
崣嵛崡
The switch D isn't
the return switch, so
be careful.
95
Airplane Function
The setting screen of each function is called from the following menu. The function when
the model type was set to airplane (AIRPLANE) is displayed here.
Power ON
● First set the
throttle to slow.
● Then turn on the
power.
（Home screen）
● When t h e E N D k e y i s
pressed, the display returns
to the home screen.
END
The wing type
is indicated
every several
seconds.
To menu screen
by holding down
the + key
$)
● When the + key is pressed for
1 second, the menu screen is
（1 second）
displayed.
＋
MENU
Airplane
MENU
1/4
MENU
2/4
MENU
3/4
（Selection）
● Move the cursor
(highlighted) up and down
and to the left and right
with the Jog key and select
the function.
The cursor can be moved
over several pages.
（Calling the setting screen）
MENU
4/4
96
● Press the Jog key to open the
setting screen.
■ The menu items can be changed according to the WING type. For example, if
WING type is 1AIL, since the item blinks, reference only the item of the WING
type used.
Relevant WING type display → WING TYPE
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
Refer to "Common Functions"
previously described for a
description of this function.
■ Function
◆ MENU 1/4
◆ MENU 2/4
◆ MENU 3/4
P.50
PRMTR
P.63
TIMER
P.92
MDL TYP
P.53
P.MIX
P.68
TRAINER
P.94
MDL NAM
P.55
AUX CH
P.71
F/S
P.57
SERVO
P.72
THR CUT
P.98
 POINT
P.59
TLMTRY
P.73
DR EXP
P.100
TRIM
P.60
SENSOR
P.86
THR CRV
P.102
SUB TRM
P.61
S.BUS
P.88
IDL DWN
P.103
REVERS
P.62
ďź­ TRANS
P.91
GYRO
P.104
Airplane
MDL SEL
◆ MENU 4/4
AIL DIF
P.105
ďźś TAIL
P.106
CAMBER
P.107
AIR BRK
P.108
EL → FLP
P.110
FLP → EL
P.111
key ／ LCD
●＋ key
●END key
ELEVON
●− key
●Jog key
P.112
97
THR CUT Throttle cut
(AIRPLANE)
WING TYPE
Function
This function cuts (stops) the engine or motor
by stick operation. At throttle operation, the rate is
adjusted to the position which completely cuts the
throttle servo or ESC when the throttle is operated.
When THR CUT is active, the throttle position is
held regardless of the throttle stick position.
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
           J        
    #   !   
 !      ?%   !
    &   *
&W?$^%/   ! *
      ! / /  
  Q ∟ z
%   ! !  !  
'            !     
       /      
             ! 
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "THR CUT"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Activating the function
Airplane
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Mode
Cut Position rate
Throttle Position
Switch selection
● Select the setting item
with the Jog key.
● Adjusts the rate to the position
that completely cuts the
throttle servo or ESC.
● The value in parentheses is the
current throttle stick position.
● Sets the ON/OFF direction of the selected switch.
○ 2P SW：NULL, UP, DOWN
○ 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN
Throttle Cut
■ Mode
① Select the "MODE" item and then select the
mode by pressing the + key or ‒ key.
＋
−
＋
−
or
or
Range：NOR, ESC
Default：NOR
● When you do not use a function, set to the
"INH" side.
● "NOR"：Engine plane
"ESC"：Electric motor plane
98
■ Activating the function
② Select the "MIX" item and then select the off
by pressing the + key or ‒ key.
Throttle Cut
■ Switch selection
③ Select the "SW" item and then select
the switch by pressing the + key or ‒
key.
＋
■ Switch direction
④ Select the "POSI" by pressing the + key or ‒ key at
the ON direction selection item.
＋
−
−
or
or
Range：
Range：SwA ∼ SwD
● 2P SW：NULL, UP, DOWN
● 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN,
DOWN
Default：SwA
■ Cut Position rate
⑤ Select the "RATE" item and then select
the cht position by pressing the + key or
‒ key (motor stop).
＋
−
（In the case of ESC ）
■ Function release Throttle Position
⑥ Select the "THR" item and then select the release
position by THR stick is lowered and Jog key is
pressed for 1 second.
or
● It adjusts to the position where an engine
is cut.
Range：-30 ∼ 0 ∼ +30%
Default：0%
● Set to a safe low throttle position.
● When you want to return the set value
to the initial value, press the + key and ‒
key simultaneously.
Range：0 ∼ 100%
Default：15%
Airplane
NOR MODE（Engine）
ESC MODE（Motor）
THR CHT
THR CHT
OFF
OFF
ON
ON
Cut switch ON
Cut switch ON
Motor Stop
THR stick LOW
(It's possible to do
positional change.）
Engine
stop
Release
OFF
Release
ON
THR stick
middle-high
(Besides the slow)
OFF
ON
Cut switch OFF
THR stick LOW
Cut switch OFF
Motor Stop
OFF
THR Active
(It's possible to do
positional change.）
ON
THR stick
LOW
Cut switch
OFF
(It's possible to do
positional change.）
Slow→High
Start
99
DR EXP
Dual rate ／ EXPO
WING TYPE
Function
(AIRPLANE)
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
D/R
The aileron, elevator and rudder channel control surface angle can be switched in 2(3) steps
'    !     @     !   '   !     
  
EXP
This function makes operation more pleasant by changing the operating curve so that servo movement
is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral
position. Adjustments can be made in 2(3) steps according to the control surface angle.
' ˆ;‰ / J   /
   ^ 
   /   
%      
   ! 
/     ˆ‰ / J   / /    
          ˆ‰   # 
      /   
   !  &z$*  &^  *'   !  
&  *  !      
Switch selection（SW）
Switches A to D can be selected as the aileron channel, elevator channel, and rudder channel dual rate
(exponential) switch.
z! ：Q ：% z ／ ^  ：% Q ／ ：% „
Method
Airplane
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "DR EXP"
from the menu with the
Jog key.
＋ （1 second）
● The channel under selection is
underlined.
Channel selection
Dual rate
（Switch Direction）
EXPO
● The dual rate and exponential
settings are displayed by a
curve.
Switch selection
● Channel selection/Select
the setting item with the
Jog key.
（Switch No.）
（D/R and EXPO rate display）
Top row；Left side ／ down
Bottom row；Right side ／ up
Select the ( ← ) ⇔ ( → ) L,R/U,D
with the stick .
100
③ Open the setting screen by
pressing the Jog key.
＜ Channel ＞
1：Aileron
2：Elevator
3：Throttle
4：Rudder
D/R
① A channel is chosen by Jog
key.
Range：1, 2, 4
② Adjust the rate by moving the cursor
to D/R with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：
0 ∟ 140%
Default：100%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the same
channel is possible by Jog key.
EXPO
① Select the "EXP" item and
then select the channel with
the Jog key.
② Adjust the rate by moving the cursor
to EXP with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：1 ∼ 4
Range：
-100 ∟ +100%
Default：0%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
● Moving to another setting item of the
same channel is possible by Jog key.
Airplane
Adjust the rate of each direction of the dual rate switch and stick by repeating step
Switch Change
① Select the "SW" item and then select
the channel with the Jog key.
② A switch is chosen by + key or -key.
＋
−
or
Range：1, 2, 4
Range：SwA ∼ SwD
101
THR CRV Throttle curve
(AIRPLANE)
WING TYPE
Function
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
This function sets a 5 point throttle curve so that
the engine/motor speed relative to movement of the
         
Q  !     
 
However, this function cannot be used when the throttle EXP function was set. When this function is set,
the throttle EXP function cannot be used.
Method
Calling the setting screen
② Select "THR CRV"
from the menu with the
Jog key.
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Activating the function
Switch selection
● The set-up curve is shown
Airplane
5 point curve
set
（Present switch position）
● Select the setting item
with the Jog key.
Throttle curve
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
● When you do not use a function, set to the
"INH" side.
■ Switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
＋
or
Range：SwA ∼ SwD、Default：SwC
■ 5 point curve set
③ By Jog key, either of P-1 to P-5 is chosen. The + key or - key is pressed and a
rate is set up.
Range：0 ∼ 100%
Default：P-1:0%, P-2:25%, P-3:50%, P-4:75%, P-5:100%
102
−
＋
−
or
IDL DWN Idle down
(AIRPLANE)
WING TYPE
Function
This function is linked to the air brake switch
and gear switch and lowers the engine idle. It is
used when engine idle is set high to prevent the
      
lower engine idle when landing.
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
'  /      
Q     #    @   
  / 
      ! / /  
  Q ∼ z'       

Method
Calling the setting screen
② Select "IDL DWN"
from the menu with the
Jog key.
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Activating the function
Idle down rate
● Select the setting item
with the Jog key.
● Sets the ON/OFF direction of the selected switch.
○ 2P SW：NULL, UP, DOWN
○ 3P SW：NULL, UP, UP&DWN, UP&CNT, CENTER, CNT&DN, DOWN
Idle down
■ Activating the function
① Select the "MIX" item
and then select the on
or off by pressing the +
key or ‒ key.
＋
■ Switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
−
or
● When you do not use a function, set to the
"INH" side.
■ Switch direction
③ Select the "POSI" by pressing the
+ key or ‒ key at the ON direction
selection item.
Range：
● 2P SW：NULL, UP, DOWN
● 3 P S W ： N U L L , U P, U P & D W N ,
UP&CNT, CENTER, CNT&DN, DOWN
＋
Airplane
Switch selection
Switch direction
−
or
Range：SwA ∼ SwD、Default：SwC
■ Idle down rate
④ Select the "RATE" item and
then ad just the idle down
rate by pressing the + key or
‒ key.
＋
−
or
Range：0 ∼ 40%
Default：0%
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
● The idle down amount is usually 10% ∼ 20%. Hold down the aircraft and set the throttle switch to the maximum
slow position while the engine is running and adjust the idle drop amount while turning the switch on and off.
103
Gyro sensor
GYRO
(AIRPLANE)
WING TYPE
Function
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
  /      ! !# 
 //  ?&‹*     
   <    
'Œ |    
<     !  Ž  

This function is dedicated mixing for switching
the gyro sensitivity and gyro mode (AVCS/
NORMAL) of Futaba airplane use gyros.
'            
  !    !    
 &%   Q   z* +!         
! #           !    Š 
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "GYRO"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Activating the function
Gain switch selection
Switch position
C u r r e n t s w i t c h o p e r a t i n g
direction）
Airplane
● Select the setting item
with the Jog key.
（Gyro type）
● Switches to the
sensitivity setting
screen of each switch
direction when the
Jog key is pressed.
（Gyro Gain）
GYRO
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
■ Gain switch selection
② Select the "SW" item and then select the
switch by pressing the + key or ‒ key.
＋
−
or
● When you do not use a function, set to the
"INH" side.
Range：SwA ∼ SwD, Default：SwB
■ Gyro mode and gain setting
③ UP, CNT, DWN, shows the switch position. Set the respective positional gain and mode.
GAIN=OFF
104
AVC 100%
AVCS
When a ＋ key is
pressed, gain of the
AVCS side is UP.
＋
0%
Normal
−
NOR 100%
When a − key is
pressed, gain of the
Normal side is UP.
AIL DIF
Aileron differential
(AIRPLANE)
WING TYPE
Function
The left and right aileron differential can be
adjusted independently. This function is restricted
to 2 servo aileron.
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
CH1
CH6
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "AIL DIF"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Aileron1（CH1）
rate
L：Aileron stick Left side rate
R：Aileron stick Right side rate
Aileron6（CH6）rate
● Select the setting item with
the Jog key.
Airplane
（Aileron）
Select the Left/Right with the
aileron stick .
Aileron Differential
■ Activating the function
① Select the "2AIL" or "2AIL1FLP"
by WING type (MDL TYP).
■ Aileron rate
② Select the "AIL1" item and move the
aileron stick to the left and right and
adjust the travel of each servo by
pressing the + key or ‒ key.
＋
−
or
Range：-120 ∼ +120%
Default：+100%
● When you want to return to the initial value, press the + key
and ‒ key simultaneously. However, when the polarity is
changed only the number returns to the initial value.
（Adjust the "AIL6" item in the same way as ② .）
105
V-Tail
V-TAIL
(AIRPLANE)
WING TYPE
Function
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
This mixing is used with V tail aircraft that
combine the elevator and rudder functions.
CH2 (CH4)
CH4 (CH2)
(Stick mode 2)
Method
Elevator UP
Elevator DOWN
Rudder Right
Rudder Left
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "V-TAIL"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Airplane
● When INH is selected, the
function cannot be used. To use
the function, select ACT.
Activating the function
ELE2 rate
ELE4 rate
（Rate adjustment）
RUD2 rate
RUD4 rate
● Select the setting item with
the Jog key.
V-TAIL
■ Activating the function
① Select the "MIX" item and then
select the "ACT" by pressing
the + key or ‒ key.
＋
−
or
● When you do not use a
function, set to the "INH" side.
■ Rate adjustment
② Select the value item and then adjust
the mixing rate by pressing the + key or
‒ key.
＋
−
or
Range：-100 ∼ +100%
Default：+50%
（only ELE4 : -50%）
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.However, polarity does not
return.
NOTE：We recommend that setting be performed while moving the stick and checking the amount of movement. If
the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range
will be exceeded and a dead band in which the servo will not operate may be created.
106
CAMBER Camber
(GLIDER)
WING TYPE
Function
The up/down travel of each flap/aileron (
flaps: FLP5, ailerons: AIL1/6) can be adjusted
independently for each servo according to the
wing type. The camber operates by switch A.
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
CH5
Flap 5
CH1
Aileron 1
'    !     !
'        
CH6
Aileron 6
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "CAMBER"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● Select the setting item
with the Jog key.
＋
● Current switch position
−
Airplane
● Switch position
● Aileron 1
● Aileron 6
● Elevator
● Flap
● Activating the function
● Switch selection
● The value is changed by
+ key or ‒ key.
107
AIR BRK Air brake
(AIRPLANE)
WING TYPE
Function
This function is used when the air brake is
necessary during landing and is turned on and off
by switch C (initial setting).
W /                J#
    &{[ *
       /    ˆ?%'‰ & !! *#  
  J             
    /  ˆV+W‰& *#   J
         ?W  ! /  
   J   
(Example)
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
+! ˆV+W‰/   #    J
    <      J   # 
       ! / <     <
        ! / J   J   
> J    #       J  
#      /  !   
!     
       ˆV+W‰ / # @     
       J    / //   
& J  / / //*
Flap down
WING type 1AIL1FLP or
2AIL1FLP
5CH
6CH
1CH
Switch C
Ailerons up
● Adjustment item for every wing type
Airplane
Display
1AIL1FLP
2AIL
2AIL1FLP
AIL1(1CH)
ELEV(2CH)
FLAP(5CH)
AIL6(6CH)
----Elevator
Flap
-----
Aileron1
Elevator
----Aileron6
Aileron1
Elevator
Flap
Aileron6
WING type 2AIL or
2AIL1FLP
ELEVON
----Elevator
Flap
-----
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "AIR BRK"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Activating the function
Rate set
Elevator delay rate set
● Select the setting item
with the Jog key.
108
$,5%5.
3CH Control set (LINR mode)
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Switch selection
Switch direction
Mode
● When the LINR operation mode was selected, the current throttle stick position is displayed
at the operation reference point and in the bottom row parentheses.
Air brake
■ Activating the function
① Select the "MIX" item and then select
the "ON" or "OFF" by pressing the +
key or ‒ key.
＋
■ Rate set
② Select the "rate" item and
adjust the servo travel by
pressing the + key or ‒ key.
−
＋
−
or
Range：-100 ∼ +100%
Default：+50%（ELEV only -10%）
or
● When you do not use a function, set
to the "INH" side.
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
However, polarity does not return.
■ Delay Rate set
③ Select the "delay" item and adjust the elevator
operation delay by pressing the + key or ‒ key.
＋
−
or
● The amount of delay is large at 100%.
Range：0 ∼ 100% Default：0%
● When you want to return the set value to the initial value, press the + key
and ‒ key simultaneously.
（In the case of change of a switch）
■ Switch selection
① Select the "SW"
i tem an d t h e n
select the switch
by pressing the
+ key or ‒ key.
＋
−
or
＋
−
or
Range：
● 2P SW：NULL, UP, DOWN
● 3P SW：NULL, UP, UP&DN, UP&CT, CENTR, CT&DN,
DOWN
（In the case of change of a mode）
■ Mode
①S e l e c t t h e ＋
−
"MOD" item
or
and select the
operation mode
by pressing the + key or the ‒ key.
Range：OFST, LINR
Default：OFST
Airplane
Range：SwA ∼ SwD
Default：SwC
■ Switch direction
② Select the ON direction by
pressing the + key or ‒ key at
the ON direction selection item.
■ Operation reference point setting ("LINR" mode
only)
② Select the operation reference point setting
item newly displayed at the bottom row
of "MOD" and hold the throttle stick at the
air brake start point and set the reference point by
pressing the Jog key for 1 second.
Range：0 ∼ 100%
（When 3CH control is changed at the time of "LINR"）
■ "LINR" mode 3CH control
① Select the "CH3" item and select control by pressing the +key or ‒
key.
Range：THR, SwA ∼ SwD, VR
Default：THR
109
EL → FLP Elevator → Flap mixing
(AIRPLANE)
WING TYPE
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
Function
This mixing is used when you want to apply
+     ]  +
          
elevator. When used with Fun Fly and other
aircraft, small loops are possible.
CH5
Flap 5
'             
@ 
CH2
Elevator
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "EL → FLP"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Select the ↑ / ↓ with the
elevator stick .
Mixing rate
（Elevator up side rate）
（Elevator down side rate）
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Activating the function
Airplane
Switch selection
Switch direction
● Select the setting item
with the Jog key.
● Sets the ON/OFF direction of the selected switch.
○ 2P SW：NULL, UP, DOWN
○ 3P SW：NULL, UP, UP&DWN, UP&CNT, CENTER, CNT&DN, DOWN
Elevator → Flap Mixing
■ Activating the function
① Select the "MIX" item
and then select the ON
or OFF by pressing the
+ key or ‒ key.
＋
■ Switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
−
or
● When you do not use a function, set to the
"INH" side.
■ Switch direction
③ Select the "POSI
" by pressing the
+ key or ‒ key at
the ON direction
selection item.
＋
−
or
Range：
● 2P SW：NULL, UP, DOWN
● 3 P S W ： N U L L , U P, U P & D W N ,
UP&CNT, CENTER, CNT&DN, DOWN
110
＋
−
or
Range：SwA ∼ SwD
■ Mixing rate
④ S e l e c t t h e " R AT E " i t e m a n d
then adjust the mixing rate by
pressing the + key or ‒ key.
Range：-100 ∼ +100%
＋
−
or
Default：+50%
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
However, polarity does not return.
● RATE ↑ / ↓ cursor position operates and chooses an
elevator stick.
FLP → EL Flap → Elevator mixing
(AIRPLANE)
WING TYPE
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
Function
This mixing is used to compensate for pitch
  "    #    
CH5
Flap 5
    /          
J  @ /      
   
'  /  !      !
&?%^'*
CH2
Elevator
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "FLP → EL"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Activating the function
Mixing rate
P r e s e n t f l a p o p e r a t i n g
position）
● Select the setting item
with the Jog key.
Airplane
Mixing offset rate
Flap → Elevator Mixing
■ Activating the function
① Select the "MIX" item and then select
the "ON" by pressing the + key or ‒
key.
＋
■ Mixing rate
② S e l e c t t h e " R AT E " i t em a n d
then adjust the mixing rate by
pressing the + key or ‒ key.
−
−
or
Range：-100 ∼ +100%
Default：0%
or
● When you do not use a function, set
to the "INH" side.
＋
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
（When changing the mixing reference point）
■ Mixing reference point offset setting
① Select the "OFFSET" item and turn the Flap knob to the
point you want to make the mixing reference point and
set the reference point by pressing the Jog key for 1
second.
（1 second）
Range：-100 ∼ +100% Default：0%
111
ELEVON Elevon
(AIRPLANE)
WING TYPE
Function
This mixing is used with delta wing, tailess, and
disk shaped airplanes that combine the aileron and
elevator functions.
Connect the CH1 servo to the left aileron and the
CH2 servo to the right aileron.
1AIL 1AIL1FLP 2AIL 2AIL1FLP ELEVON
CH2
'             @ 
 
CH1
Pitch (Elevator operation)
CH2
CH1
Roll (Aileron operation)
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "ELEVON"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Airplane
Select the Left/
Right with the
aileron stick .
Aileron1
（CH1）rate
（Aileron rate）
Aileron2
（CH2）
rate
L：Aileron stick Left side rate
R：Aileron stick Right side rate
Elevator2（CH1）rate
（Elevator rate）
Elevator1
（CH2）rate
● Select the setting item with
the Jog key.
ELEVON
■ Activating the function
① Select the "ELEVON" by WING
type (MDL TYP).
■ Rate set
② Select the "RATE" item and then adjust
the mixing rate by pressing the + key or
‒ key.
＋
−
or
Range：-120 ∼ +120%
Default：+100%
（only ELE1 : -100%）
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.However, polarity does not
return.
NOTE：We recommend that setting be performed while moving the stick and checking the amount of movement. If
the amount of movement is too large, elevator and aileron operation will be compounded and the servo travel range
will be exceeded and a dead band in which the servo will not operate may be created.
112
HELICOPTER Function
The setting screen of each function is called from the following menu. The function when
the model type was set to helicopter is displayed here.
PowerON
● First set the
throttle to slow.
The SWSH type
is indicated
every several
seconds.
● Then turn on the power.
● When t h e E N D k e y i s
pressed, the display
returns to the home
screen.
+5
（Home screen）
END
To menu screen
by holding down
the + key
● When the + key is pressed for
（1 second） 1 second, the menu screen is
displayed.
＋
MENU
MENU
1/4
MENU
3/4
（Selection）
● Move the cursor
( h i g h l i g ht e d ) u p a n d
down and to the left and
right with the Jog key and
select the function.
The cursor can be moved
over several pages.
Helicopter
MENU
2/4
（Calling the setting screen）
MENU
4/4
● Press the Jog key to open the
setting screen.
113
key ／ LCD
●＋ key
Refer to "Common Functions"
previously described for a
description of this function.
●− key
●Jog key
●END key
■ Function
◆ MENU 1/4
Helicopter
114
◆ MENU 2/4
◆ MENU 3/4
MDL SEL
P.50
PRMTR
P.63
TIMER
P.92
MDL TYP
P.53
P.MIX
P.68
TRAINER
P.94
MDL NAM
P.55
AUX CH
P.71
CONDIT
P.115
F/S
P.57
SERVO
P.72
THR CUT
P.116
 POINT
P.59
TLMTRY
P.73
DR EXP
P.118
TRIM
P.60
SENSOR
P.86
OFFSET
P.120
SUB TRM
P.61
S.BUS
P.88
DELAY
P.121
REVERS
P.62
ďź­ TRANS
P.91
GYRO
P.122
◆ MENU 4/4
SWH AFR
P.123
SWH MIX
P.124
THR CRV
P.126
PIT CRV
P.128
REVO MX
P.130
TH HOLD
P.132
HOV THR
P.133
HOV PIT
P.134
Condition switching at each
setting screen）
● Press the jog button for 1 second.
When setting conditions with the
following function, each setting can
be made by switching the condition
by pressing the Jog key for 1 second.
Throttle curve, Pitch curve,
Pitch → Rudder, Gyro sens, OFFSET,
Swash MIX
CONDIT Condition select (Idle-upポThrottlehold) (HELICOPTER)
Function
The condition switches (idle up 1/2 and throttle
hold switch) are not operative at initial setting.
Switch setting is performed in advance with the
condition select function.
+       |} %Q &!  *#   ~}
%„&!  *#   }%&!  *
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "CONDIT"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Idle-up
setting
Throttlehold
setting
● Select the setting item
with the Jog key.
（Activating thefunction） （Switch direction ）
（Switch selection ）
■ Activating the function
① Select the "INH" item of the
condition you want to use and set
it to "ON" or "OFF" by pressing the
+ key or ‒ key.
＋
Helicopter
Condition select
−
or
● Set conditions you do not want to use to "INH".
（In the case of change of a switch）
■ Switch selection
② A cursor is moved to ＋
"Switch selection" and
or
a switch is changed by
＋ key or − key.
−
Range：SwA ∼ SwD
Default：SwA（IDLE-UP1）,
SwB
（IDLE-UP2）
, SwC（THR-HOLD）
■ Switch direction
③ A cursor is moved to
"Switch direction" and
a switch direction is
changed by ＋ key or −
key.
＋
−
or
Range：
● 2P SW：NULL, UP, DOWN
● 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN,
DOWN
115
THR CUT Throttle cut
(HELICOPTER)
Function
This function cuts (stops) the engine or motor
by stick operation. At throttle operation, the rate is
adjusted to the position which completely cuts the
throttle servo or ESC when the throttle is operated.
When THR CUT is active, the throttle position is
held regardless of the throttle stick position.
           J        
    #   !   
 !      ?%   !
    &   *
&W?$^%/   ! *
      ! / /  
  Q ∟ z
%   ! !  !  
'            !     
       /      
             ! 
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "THR CUT"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Activating the function
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
Helicopter
Mode
Cut Position rate
Throttle Position
Switch selection
● Select the setting item with
the Jog key.
● Adjusts the rate to the position
that completely cuts the
throttle servo or ESC.
● Sets the ON/OFF direction of the selected switch.
○ 2P SW：NULL, UP, DOWN
○ 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN
Throttle Cut
■ Mode
① Select the "MODE" item and then select the
mode by pressing the + key or ‒ key.
＋
−
■ Activating the function
② Select the "MIX" item and then select the off
by pressing the + key or ‒ key.
＋
−
or
or
Range：NOR, ESC
Default：NOR
● When you do not use a function, set to the
"INH" side.
● "NOR"：Engine plane
"ESC"：Electric motor plane
116
● The value in parentheses is the
current throttle stick position.
Throttle Cut
■ Switch selection
③ Select the "SW" item and then select
the switch by pressing the + key or ‒
key.
＋
■ Switch direction
④ Select the "POSI" by pressing the + key or ‒ key at
the ON direction selection item.
＋
−
−
or
or
Range：
Range：SwA ∼ SwD
● 2P SW：NULL, UP, DOWN
● 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN,
DOWN
Default：SwA
■ Cut Position rate
⑤ Select the "RATE" item and then select
the cht position by pressing the + key or
‒ key (motor stop).
＋
−
（In the case of ESC ）
■ Function release Throttle Position
⑥ Select the "THR" item and then select the release
position by THR stick is lowered and Jog key is
pressed for 1 second.
or
● It adjusts to the position where an engine
is cut.
Range：-30 ∼ 0 ∼ +30%
Default：0%
● Set to a safe low throttle position.
● When you want to return the set value
to the initial value, press the + key and ‒
key simultaneously.
Range：0 ∼ 100%
Default：15%
NOR MODE（Engine）
ESC MODE（Motor）
THR CHT
THR CHT
ON
ON
Cut switch ON
Cut switch ON
Motor Stop
THR stick LOW
(It's possible to do
positional change.）
Engine
stop
Release
Helicopter
OFF
OFF
OFF
Release
ON
THR stick
middle-high
(Besides the slow)
OFF
ON
Cut switch OFF
THR stick LOW
Cut switch OFF
Motor Stop
OFF
THR Active
(It's possible to do
positional change.）
ON
THR stick
LOW
Cut switch
OFF
(It's possible to do
positional change.）
Slow→High
Start
117
DR EXP
Dual rate ／ EXPO
(HELICOPTER)
Function
D/R
The aileron, elevator and rudder channel control surface angle can be switched in 2 (3) steps
'    !     @     !      ' ! 
 &  *  !       
EXP
This function makes operation more pleasant by changing the operating curve so that servo movement
is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral
position. Adjustments can be made in 2 (3) steps according to the control surface angle.
' `;` / J   /
   ^ 
   /   
%      
   ! 
/     `` / J   / /    
          ``   # 
      /   
   !  &z$*  &^  *'   !  
&  *  !      
Switch selection（SW）
Switches A to D can be selected as the aileron channel, elevator channel, and rudder channel dual rate
(exponential) switch.
%：% Q ∼ % z ／   ： 
z! ：Q ：% z ／ ^  ：% Q ／ ：% „
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "DR EXP"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Helicopter
● The channel under selection is
underlined.
Channel selection
Switch direction
（present switch position ）
Dual rate
EXPO
● The dual rate and exponential
settings are displayed by a
curve.
Switch selection
● Channel selection/Select
the setting item with the
Jog key.
● Jog key is pushed for 1
second, a condition screen
will change.
118
（Switch number）
（Rate）
＜ Channel ＞
1：Aileron
2：Elevator
4：Rudder
Dual rate
■ Channel selection
① A channel is chosen
by Jog key.
■ Switch direction
② Select the "No" item and
then select the switch
direction or condition by
pressing the + key or ‒
key.
＋
Range：1, 2, 4
■ D/R Setup of rate
③ Select each function item of "D/R" and
set the rate by pressing the + key or ‒
key.
＋
−
or
−
or
Range：0 ∼ 140% Default：100%
● When you want to return the set value
to the initial value, press the + key and ‒
key simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the same
channel is possible by Jog key.
EXPO
■ Channel selection
① A channel is chosen
by Jog key.
■ Switch direction
② Select the "No" item and
then select the switch
direction or condition by
pressing the + key or ‒
key.
Range：1, 2, 4
＋
■ EXP Setup of rate
③ Select the "EXP" item and then adjust
the rate by pressing the + key or ‒ key.
＋
−
or
−
Range：-100 ∼ +100%、Default：0%
or
● When you want to return the set value
to the initial value, press the + key and ‒
key simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
Switch Change
■ Channel selection
① Select the "SW" item and then select
the channel with the Jog key.
Helicopter
● Moving to another setting item of the same
channel is possible by Jog key.
■ Switch selection
② A switch or Cond is chosen by + key or
‒ key.
＋
−
or
Range：1, 2, 4
Range：SwA ∼ SwD, Cond
● When "Cond" is chosen, a setup is
possible for every condition.
119
OFFSET
Trim offset
(HELICOPTER)
Function
If this trim offset function is used, independent
trim adjustments can be made during hovering and
in the air. This function can offset the ailerons,
elevators, and rudder neutral position by linking
to the set switch or condition. A habit that tends
to appear from the standpoint of helicopter
characteristics when flying at high speed is
possible. This function can correct this habit.
   J      #    
      #   !! ! 
     
           
    ! %     !        
!!   @ / !   !#
     !   
    Q>%/   ##
  !!   / ‹&   * / J
        
      | !!   / 
 !  ~     ~ !!   / 
    !   <      VJ   
   &+zV|,~,?Vz*    
   !! !   #   @ / 
   /' / @  
   &   !! !  ?W#
   /   J*
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "OFFSET"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this Function
select INH. The display of On/Off is
shown when active and assigned
to a switch.
● Select the setting item with
the Jog key.
Activating the function
Switch direction,
Selection of condition
Offset rate
（Present condition ）
Helicopter
● When "Cond" is chosen,
if Jog key is pushed for
1 second, it will change
to each condition
setting screen.
Switch selection
Trim offset
■ Activating the function
① Select the "MIX" item
an d t h e n select the
"ON" or "OFF" by
pressing the + key or ‒
key.
＋
■ Switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
−
or
● When you do not use a function, set to the
"INH" side.
■ Switch direction and condition
selection
③ Select the switch direction and
condition you want to set at the switch
direction and
＋
−
condition items.
or
120
＋
−
or
Range：Cond, SwA ∼ SwD
■ Offset rate
④ Select the "RATE" item and then adjust the offset rate
by pressing the + key or ‒ key.
Range：-120 ∼ +120%
Default：0%
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
DELAY
Delay
(HELICOPTER)
Function
This function prevents sudden offset changes
when the offset, condition functions are turned on
and off.
z       #  ##
  #  
'     //    !! #  ;
 !  
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "DELAY"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● Select the setting item
with the Jog key.
Delay rate
● The delay is maximum at 100%
(slowly).
Delay rate
＋
−
or
Range：0 ∼ 100%
Default：0%
Helicopter
■ Delay rate setup
① Select the "RATE" item and then adjust
the delay rate by pressing the + key or ‒
key.
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.
121
GYRO
Gyro mixing
(HELICOPTER)
Function
         
'        
'Œ |    
<     !  Ž  

This mixing adjusts the gyro sensitivity from the
transmitter. The AVCS gyro (AVC mode) or normal
gyro (NOR mode) can be selected.
'   J    & * 
      
  ƒ_/   #`Q>` `W?`
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "GYRO"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Activating the function
Gain switch selection
（Present switch position）
Condition
● Select the setting item
with the Jog key.
（Gyro type）
（Gyro Gain set）
● Swit c h e s t o t h e
gain setting
screen of each
condition when
the Jog key is pressed.
● When a Futaba GY gyro is used, gyro type "GY" is selected. This switches the gyro gain setting
item to the mode and gain direct reading display.
Helicopter
Gyro setup
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
■ Gain switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
● When you do not use a function, set to the
"INH" side.
＋
−
or
Range：Cond, SwA ∼ SwD
■ Gyro mode and gain setting
③ When choosing Cond. → Set a mode and gain every each condition.
When choosing Switch → UP, CNT, DWN, shows the switch position. Set the respective
positional gain and mode.
GAIN=OFF
122
AVC 100%
AVCS
When a ＋ key is
pressed, gain of the
AVCS side is UP.
＋
0%
Normal
−
NOR 100%
When a − key is
pressed, gain of the
Normal side is UP.
SWH AFR Swash AFR
(HELICOPTER)
（When swash type is H-1, this setting screen is not displayed.）
Function
This is the adjustable function rate (AFR) function when HR3, H-3, HE3, HN3 or H-2 is selected
as the swash type. The ailerons, elevators, and pitch
steering angle and direction can be adjusted.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "SWH AFR"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● Depending on the swash type the
screen display is different.
● Select the setting item
with the Jog key.
● When the polarity is changed, the
direction of operation is reversed.
Rete
NOTE：If the steering angle is too large, linkage binding may occur .
■ Travel adjustment of each function
① Select each function item of "RATE" and
set the rate by pressing the + key or ‒
key.
＋
−
or
Helicopter
Swash AFR
Range：-100 ∼ +100%
Default：+50%
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously. However, polarity does not
return.
123
SWH MIX Swash mixing
(HELICOPTER)
Function
This mixing is used to correct the bad tendencies
of the swash plate in the aileron direction and
elevator direction relative to aileron, elevator, and
pitch operations. It adjusts the rate of the direction
that requires correction so that the servo operates
smoothly in the proper direction relative to each
operation.
'    /  !     

'  !    &   *   
/   !     
Example of use: Using to correct bad roll tendencies
① AIL → ELE is set to ON.
② ACTION/ON is common to all conditions. The rate of unused conditions is set to 0%.
③ When the nose drops at right roll and the right side rate is adjusted in the "+"
direction, the elevators move to the up side when the right aileron is deflected.
Left roll can be adjusted by left side rate.
However, since the left and right ailerons polarity and elevators operating direction
relationship is reversed; check the correction direction by swash plate operation.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "SWH MIX"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● Select the setting item
with the Jog key.
Helicopter
Condition
Mixing master direction
Mixing rate
（Rate）
● When not using this function,
select INH.
Activating the function
124
（Present condition）
Swash mixing
■ Activating the function
① Select the "MIX" item and then select the
"ON" by pressing the + key or ‒ key.
＋
■ Setup of rate
② Select the "RATE" item and then adjust the mixing
rate by pressing the + key or ‒ key.
−
Range：-100 ∼ +100%
Default：0%
or
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
● When you are not using a function, set
this to INH.
● ON/OFF of a function, setup of rate, and a trim, Jog key is pushed and
setting condition can be chosen.
Range：
NORM, IDL1, IDL2, HOLD
Helicopter
125
THR CRV Throttle curve
(HELICOPTER)
Function
The throttle curve function sets a 5 point curve in
relation to the throttle stick movement and adjusts
each point over the 0 ∟ 100% range so that the
     
W /  &W?*#   | &+zV|*#   ~ &+zV~*
     
'  / &W?*#|&+zV|*#~&+zV~*
     ;         

（Normal throttle curve adjustment method）
The normal throttle curve creates a basic throttle curve centered near hovering. This curve is
adjusted together with the normal pitch curve so that engine speed is constant and up/down
control is easiest. The normal throttle function is always on.
（Idle up 1/2 throttle curve adjustment method）
The idle up curves are set so that the engine maintains a constant speed even when the pitch is
reduced during flight. Curves matched to the purpose such as loop, roll and 3D are created and idle
up curves 1/2 are by aerobatics.
CAUTIONS
Operation precautionsWhen starting the engine, always set idle up
sticks 1/2 to OFF and start the engine at idling.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "THR CRV"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Helicopter
● When not using this Function
select INH. The display of On/
Off is shown when active
and assigned to a switch. A
display when normal is "---"
（alwaysON）
Activating the function
Setting condition
5point curve
rate
● The THR-CURVE settings are
displayed by a curve.
● Select the setting item
with the Jog key.
（Rate） （Present condition）
126
Throttle curve
■ Activating the throttle curves (ID1/2)
① Select the "MIX" item and set to ＋
"ON" or "OFF" by pressing the +
key or ‒ key.
−
or
● For the normal condition, "---" is displayed. (Always ON)
Range：NOR, ID1, ID2
● When you do not want to use an idle up curve, set to
"INH".
■ 5 point curve setting
② Select the setting item of each point (P-1 ∼ P-5)
with the Jog key and set the travel of each point by
pressing the + key or ‒ key.
＋
−
Default：
P-5: 100%
P-4: 75%
P-3: 50%
P-2: 25%
P-1: 0%
Range：0 ∼ 100%
or
● When you want to return the set value to
the initial value, press the + key and ‒ key
simultaneously.
■ Curve copying method
① Select the "CND" item
and switch to the curve
copy mode by pressing
the Jog key.
② Press the + key or ‒
key and select the copy
destination condition.
＋
③ Copy the condition by
pressing the Jog key for
1 second.
−
（1 second）
or
● Throttle curve setting examples
50
25
P1
50
P3
P4
STICK
（Normal）
P5
P1
P5=100.0%
P4= 75.0%
P3= 65.0%
P2= 65.0%
P1= 67.0%
75
50
25
25
P2
（The example of a setting ）
100
P5=100.0%
P4= 75.0%
P3= 50.0%
P2= 54.0%
P1= 56.0%
75
RATE
RATE
75
（The example of a setting ）
100
P2
P3
P4
P5
P1
P2
STICK
（Idle-up1）
P3
P4
P5
Helicopter
P5=100.0%
P4= 65.0%
P3= 50.0%
P2= 30.0%
P1= 0.0%
RATE
（The example of a setting ）
100
STICK
（Idle-up2）
NOTE：Set the actual value of the throttle curve according to the fuselage
specications.
127
PIT CRV Pitch curve
(HELICOPTER)
Function
The pitch curve function allows setting by a 5
point curve in relation to throttle stick movement
and adjustment of each point over the -100% ∟
+100% range so that the pitch enters the optimum
   
W / &W?*#|&+zV|*#~&+zV~*# 
&Vz*    
'  / &W?*#|&+zV|*#~&+zV~*#
  &?Vz*       ;    
      
NOTE：When the hold switch is on, the hold function has
priority even though an idle up switch is in any position.
（Normal curve adjustment method）
The normal pitch curve creates a basic pitch curve centered near hovering. This curve is adjusted
together with the throttle pitch curve so that engine speed is constant and up/down control is
easiest.
（Idle up 1/2 curve adjustment method）
The high side pitch curve sets the maximum pitch that does not apply a load to the engine. The low
side pitch curve is created to match the purpose such as loop, roll, and 3D. The idle up 1/2 curves are
used by aerobatics.
（Throttle hold curve adjustment method）
The throttle hold curve is used when performing auto rotation dives. Set the intermediate pitch to
match the stick work at pitch up.
Method
Calling the setting screen
Helicopter
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "PIT CRV"
from the menu with the
Jog key.
＋ （1 second）
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch. When
normal,"---" (always ON) is
displayed.
Activating the function
Condition
5point curve
rate
● Select the setting item
with the Jog key.
● The PIT-CURVE settings are
displayed by a curve.
（Rate）
128
③ Open the setting screen by
pressing the Jog key.
（Present condition）
Pitch curve
■ Activating the pitch curves
（ID1/2, HLD）
① Select the "MIX" item and then ＋
select the "ON" or "OFF" by
or
pressing the + key or ‒ key.
−
● For the normal condition, "---" is displayed. (Always ON)
Range：NOR, ID1, ID2, HLD
● When you do not want to use an idle up, hold curve, set
to "INH".
Default：
P-5: +100%
P-4: +50%
P-3: 0%
P-2: -50%
P-1: -100%
■ 5 point curve setting
② Select the setting item of each point (P-1 ∼ P-5)
with the Jog key and set the travel of each point by
pressing the + key or ‒ key.
＋
−
Range：-100 ∼ +100%
or
● When you want to return the set value to
the initial value, press the + key and ‒ key
simultaneously.
■ Curve copying method
① Select the "CND" item
and switch to the curve
copy mode by pressing
the Jog key.
② Press the + key or ‒
key and select the copy
destination condition.
＋
③ Copy the condition by
pressing the Jog key for
1 second.
−
（1 second）
or
● Pitch curve setting examples
-50
-100
P1
P5= +40%
P4= +10%
P3= -10%
P2= -40%
P1= -70%
P2
P3
P4
-100
P1
P5
（Normal）
P2
P3
STICK
P4
（Idle-up1）
（The example of a setting ）
+100
+50
+50
P5= +40%
P4= +10%
P3= -10%
P2= -50%
P1= -80%
-50
-50
STICK
RATE
+50
RATE
P5= +70%
P4= +50%
P3= +6%
P2= -40%
P1= -70%
（The example of a setting ）
+100
P5
-100
P1
P2
P3
P4
P5
STICK
Helicopter
RATE
+50
（The example of a setting ）
+100
RATE
（The example of a setting ）
+100
（Idle-up2）
NOTE：Set the actual value of the pitch curve according to
the fuselage specications.
P5= +100%
P4= +50%
P3=
0%
P2= -50%
P1= -100%
-50
-100
P1
P2
P3
STICK
P4
P5
（Hold）
129
REVO MX Pitch → Rudder mixing
(HELICOPTER)
Function
*   ÂŚ  +  
the pitch of the tail rotor to suppress the reaction
torque (force that attempts to swing the helicopter
in the direction opposite the direction of rotation
of the main rotor) generated by the main rotor
pitch and speed. It is adjusted so that the pitch of
the tail rotor is also changed when the main rotor
pitch changes and reaction torque appears and so
that the nose does not swing to the left and right.
However, when the AVCS mode is used with a GY
&   ÂŚ  +   
'  / &W?*|$~&+zV|#~*   

'           @ 
    J        #     
             /   
           /     
   J        #      
  '           
    
   }V  &V?*;|‡#   &+ƒ*
|‹
    } V   &V?* |‹#   
&+ƒ*;|‹
*'                
 /        
Adjustment procedure
First, trim at hovering and then adjust the neutral position.
（Normal pitch → rudder mixing）
Helicopter
● Throttle low side (slow while hovering) adjustment
Repeatedly hover from take off and land from hovering at a constant rate matched to your own rhythm, and
adjust pitch → rudder mixing so that the nose does not deflect when the throttle is raised and lowered.
If the nose points to the left when landing from hovering or points to the right when taking off, when hovering
stabilizes and the stick moves to the neutral position, low side mixing rate is probably too large and when
the nose points in the opposite direction, low side rate is probably too small. However, when landing, the
direction of the nose may not stabilize depending on the state on the ground. The direction of the nose may
also become unstable when rotation of the rotor does not rise.
● Throttle high (up to climbing from hovering and diving hovering) adjustment
Repeat up to climbing from hovering and diving hovering matched to your own rhythm and adjust
pitch → rudder mixing so that the nose does not deflect to the left and right when the throttle is raised and
lowered. If the nose points to the right when climbing from hovering, the high side mixing rate is too large and
if the nose points to the right, the mixing rate is too small. Repeat climbing and diving and make adjustment
while taking the balance.
（idle-up1/2 Pitch → Ruddermixing）
This mixing sets the mixing rate so that the rudder direction is straight forward at high speed flight.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
＋ （1 second）
130
② Select "REVO MX"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
● When not using this function,
select INH.
Activating the function
Selection of condition
High side Setup of rate
Low side Setup of rate
（present switch position ）
● Select the setting item
with the Jog key.
（Rate）
Pitch → Rudder mixing
■ Activating the function
① Select the "MIX" ＋
item and then
select the "ON" by
pressing the + key
or ‒ key.
■ Selection of condition
② Select the "COND" item
and selection of condition
by pressing the + key or ‒
key.
−
or
−
or
Range：NORM, IDL1/2
● When you do not use a function, set to
the "INH" side.
■ Setup of rate
③ Select each function item of "HI"or
"LO" and set the rate by pressing the
+ key or ‒ key.
＋
＋
−
or
Range：-100 ∼ +100%
Default(NORM)：-20%(LOW) +20%(HIGH)
Default(IDL1/2)：0%(LOW) 0%(HIGH)
● When you want to return the set value to the initial value,
press the + key and ‒ key simultaneously.
Helicopter
131
TH HOLD Throttle hold
(HELICOPTER)
Function
The throttle hold function fixes or stops the
engine throttle position by hold switch operation
during an auto rotation dive. Operation can be
set within the -50% ∟ +50% range based on the
throttle trim position.
The switch is changed at the conditions selection
screen. (Initial setting: SwD)
CAUTIONS
NOTEPriority is given to throttle hold over idle-up.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "TH HOLD"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Activating the function
● When not using this Function
select INH. The display of On/
Off is shown when active and
assigned to a switch.
hold throttle position
● Select the setting item with
the Jog key.
Throttle hold
Helicopter
■ Activating the function
① Select the "MIX" item and then
select the "ON" or "OFF" by
pressing the + key or ‒ key.
＋
−
or
■ Hold throttle position
② Select the "RATE" item and then adjust
the rate by pressing the + key or ‒ key.
＋
−
or
Range：-50 ∼ +50%
Default：0%
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.
● When you do not use a
function, set to the "INH" side.
● Function ACT ↔ INH is linked to 【Hold position adjustment method】
condition THR-HOLD, and can be set ● When you want to lower the engine idling, set to the "+" direction and
at any screen.
adjust so that the carburetor is full open.
● When maintaining idling, set the throttle stick to the slow position and
turn the hold switch on and off and set to the number at which the servo
does not operate.
NOTE：When connecting the throttle linkage, lower the digital trim to the
slowest and adjust so that the carburetor is full open.
132
HOV THR Hovering throttle
(HELICOPTER)
Function
The hovering throttle function trims the throttle
near the hovering point.
When the hovering throttle knob is turned
clockwise, the speed increases and when it is turned
counterclockwise, the speed decreases. Rotor
speed changes due to changes in the temperature,
humidity, and other flying conditions can be
trimmed. Adjust for the most stable rotor speed.
More precise trimming is possible by using this
function together with the hovering pitch function.
'        ! / 
 /   / $|
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "HOV THR"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When "INH", the function
cannot be used. To use the
function, switch to "ON".
Activating the function
Trim memory settting
Compensation amount at trim
memory）
VR setting
Selection of condition
Actual compensation amount
including the hovering throttle
VR）
● Select the setting item
with the Jog key.
● NORM：Only the normal condition operates
● NORM/IDL1：It operates by normal condition and
idle-up1.
● The VR operating direction is
different depending on the
polarity.
Hovering Throttle
−
or
● When you do not use a function, set to
the "INH" side.
■ VR setting
③ Select the "VR" item and then select the
"VR" by pressing the + key or ‒ key.
Range：NULL
（OFF）
, +VR, -VR
Default：NULL
■ Selection of condition
② Select the "MODE" item
and then select condition
by pressing the + key or ‒
key.
＋
−
or
Range：NORM, NORM/IDL1
Default：NORM
Helicopter
■ Activating the function
① Select the "MIX" ＋
item and then
select the "ON" by
pressing the + key
or ‒ key.
（Memorizing the hovering throttle adjustment position）
■ Memory setting
④ Select the "RATE" item and memorize the
current trim position by pressing the Jog
key.
● When the knob is returned to the center after
memorization, the trim position returns to its
previous position.
NOTEIf memorization is repeated at the same
position, the value is cumulated.
133
HOV PIT Hovering pitch
(HELICOPTER)
Function
The hovering pitch function trims the pitch near
the hovering point.
When the hovering pitch knob is turned
clockwise, the pitch gets stronger and when it is
turned counterclockwise, the pitch gets weaker.
Rotor speed changes due to changes in temperature,
humidity, and other flying conditions can be
trimmed. Adjust for the most stable rotor rotation.
Method
More precise trimming is possible by using
this function together with the hovering throttle
function.
'            ! /
 /    / $|
'  /       //  +!   
// !  / //    #
    /   /
    J           /
    
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "HOV PIT"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When "INH", the function
cannot be used. To use the
function, switch to "ON".
Activating the function
Trim memory settting
Compensation amount at trim
memory）
VR setting
Selection of condition
Actual compensation amount
including the hovering pitch
VR）
● Select the setting item
with the Jog key.
● NORM：Only the normal condition operates
● NORM/IDL1：It operates by normal condition and
idle-up1.
● The VR operating direction is
different depending on the
polarity
Helicopter
Hovering Pitch
■ Activating the function
① Select the "MIX" ＋
item and then
select the "ON" by
pressing the + key
or ‒ key.
−
or
● When you do not use a function, set to
the "INH" side.
■ VR setting
③ Select the "VR" item
and then select the
"VR" b y p r e s s i n g
the + key or ‒ key.
＋
Range：NULL
（OFF）
, +VR, -VR
Default：-VR
−
or
■ Selection of condition
② Select the "MODE" item
and then select condition
by pressing the + key or ‒
key.
＋
−
or
Range：NORM, NORM/IDL1
Default：NORM
（Memorizing the hovering pitch adjustment position）
■ Memory setting
④ Select the "RATE" item and memorize the current
trim position by pressing the Jog key.
● When the knob is returned to the center after
memorization, the trim position returns to its
previous position.
NOTEIf memorization is repeated at the same
position, the value is cumulated.
134
Glider function
The setting screen of each function is called from the following menu. The function when
the model type was set to glider (2AIL4FLP) is displayed here.
Power ON
● First set the
throttle to slow.
● Then turn on
the power.
● W hen t h e E N D k e y i s
pressed, the display
returns to the home
screen.
END
The wing type
is indicated
every several
seconds.
To menu screen
by holding down
the + key
$)
（Home screen）
＋
（1 second） ● When the + key is pressed for
1 second, the menu screen is
displayed.
MENU
MENU
1/4
MENU
2/4
Glider
MENU
3/4
（Selection）
● Move the cursor
( h i g h l i g ht e d ) u p a n d
down and to the left and
right with the Jog key and
select the function.
The cursor can be moved
over several pages.
（Calling the setting screen）
MENU
4/4
§Press the Jog key to open the
setting screen.
135
■ The menu items can be changed according to the WING type. For example, if
WING type is 1AIL, since the item blinks, reference only the item of the WING
type used.
Relevant WING type display → WING TYPE
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
Refer to "Common Functions"
previously described for a
description of this function.
■ Function
◆ MENU 1/4
◆ MENU 2/4
◆ MENU 3/4
MDL SEL
P.50
PRMTR
P.63
TIMER
P.92
MDL TYP
P.53
P.MIX
P.68
TRAINER
P.94
MDL NAM
P.55
AUX CH
P.71
CONDIT
P.137
F/S
P.57
SERVO
P.72
 POINT
P.59
TLMTRY
P.73
DR EXP
P.138
TRIM
P.60
SENSOR
P.86
SUB TRM
P.61
S.BUS
P.88
MOT SW
P.140
REVERS
P.62
ďź­ TRANS
P.91
GYRO
P.141
◆ MENU 4/4
Glider
136
AIL DIF
P.142
ďźś TAIL
P.143
BUTFLY
P.144
TRM MIX
P.145
EL → CMB
P.146
CMB MIX
P.148
AL → CMB
P.149
Key ／ LCD
●＋ key
●END key
●− key
●Jog key
CONDIT Condition
(GLIDER)
WING TYPE
Function
The condition function lets you change multiple
settings by one switch operation. Different
settings can be made immediately by switching 2
conditions.
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
'  !   
are:
    
     
・Camber MIX ・„
・^V^‘ / ・Q+V‘ /
ポTrim mix
Method
Calling the setting screen
② Select "CONDIT"
from the menu with the
Jog key.
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this
Function select INH.
The display of On/Off is
shown when active and
assigned to a switch.
Condition1
● Priority is given to the
condition 2 when the
condition 1 and 2 is turned on
simultaneously.
Condition2
● Select the setting item
with the Jog key.
（Activating the function）
（Switch direction）
（Switch selection）
CONDITION
＋
−
or
Glider
■ Activating the function
① Select the "INH" item of the
condition you want to use and
then set that condition to "ON" or
"OFF" by pressing the + key or ‒
key.
● Set conditions you do not want to use to "INH".
（Changing the switch）
■ Switch selection
② Change the switch by
pressing the + key or
‒ key at the switch
selection item.
＋
−
or
■ Switch direction
③ Select the ON direction
by pressing the + key or
‒ key at the ON direction
selection item.
＋
−
or
Range：
Range：SwA ∼ SwD
Default：SwA
● 2P SW：NUL, UP, DWN
● 3P SW：NULL, UP, U&D, U&C, CNT, C&D, DWN
137
DR EXP
Dual rate ／ EXPO
WING TYPE
Function
(GLIDER)
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
D/R
The aileron, elevator and rudder channel control surface angle can be switched in 2(3) steps
'    !     @     !   '   !     
  
EXP
This function makes operation more pleasant by changing the operating curve so that servo movement
is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral
position. Adjustments can be made in 2(3) steps according to the control surface angle.
' ˆ;‰ / J   /
   ^ 
   /   
%      
   ! 
/     ˆ‰ / J   / /    
          ˆ‰   # 
      /   
   !  &z$*  &^  *'   !  
&  *  !      
Switch selection（SW）
Switches A to D can be selected as the aileron channel, elevator channel, and rudder channel dual rate
(exponential) switch.
z! ：Q ：% z ／ ^  ：% Q ／ ：% „
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "DR EXP"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● The channel under selection is
underlined.
Channel selection
Glider
Dual rate
（Switch Direction）
EXPO
● The dual rate and exponential
settings are displayed by a
curve.
Switch selection
● Channel selection/Select
the setting item with the
Jog key.
（Switch No.）
（D/R and EXPO rate display）
Top row；Left side ／ down
Bottom row；Right side ／ up
Select the ( ← ) ⇔ ( → ) L,R/U,D
with the stick .
138
＜ Channel ＞
1：Aileron
2：Elevator
3：Throttle
4：Rudder
D/R
① A channel is chosen by Jog
key.
Range：1, 2, 4
② Adjust the rate by moving the cursor
to D/R with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：
0 ∟ 140%
Default：100%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the same
channel is possible by Jog key.
EXPO
① Select the "EXP" item and
then select the channel with
the Jog key.
② Adjust the rate by moving the cursor
to EXP with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：1 ∼ 4
Range：
-100 ∟ +100%
Default：0%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the
same channel is possible by Jog key.
Switch Change
① Select the "SW" item and then select
the channel with the Jog key.
② A switch is chosen by + key or -key.
＋
−
or
Range：SwA ∼ SwD
Glider
Range：1, 2, 4
139
MOT SW Motor switch
(GLIDER)
WING TYPE
Function
This function sets the operating motor when
the EP glider with motor is started by switch. The
operating speed can individually set in 2 ranges
of high from slow and slow from high. If you do
motor control with a throttle stick, you should
set this function to INH.
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
  !# ?W$?   !   ! !
  
+!   /       
  /   %
  ?W#      
 „         
 /  ;    ?
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "MOT SW"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● Present motor
control position
● OFF-position
(0% : OFF)
6$)(
● ON-position
(100% : High)
67$57
● Decelerating speed setting
6:㌣6Z$
㌣'2:1
6:㌣6Z'
㌣'2:1
● If this safety switch
is not ON, the
motor will not start
even if the starter
switch is turned on.
In "NULL", a safe
function does not
work.
● Start SW
● Accelerating speed setting
Motor
■ Activating the function
① Select the "MODE" item
and then select the
"OFF" by pressing the
+ key or ‒ key.
＋
■ Switch selection
② Change the switch by
pressing the + key or
‒ key a t t h e s w i t c h
selection item.
−
or
● When you do not use a function, set to the
"INH" side.
Glider
■ Switch direction
③ Select the ＋
" D O W N " it em
or
and then select
the position by
pressing the + key or ‒ key.
−
＋
or
Range：SwA ∼ SwD
■ Speed setting
④ Select "SPEED " next to (OFF) and (ON) by Jog key.
Range：OFF, 1 ∼ 10 (more slowly)
● (ON) is the acceleration speed setting.
● (OFF) is the deceleration speed setting.
● 2P SW：UP, DOWN
● 3P SW： UP, UP&D, UP&C, CNTR,
C&DN, DOWN
DANGER
Always remove the propeller from the motor during setting and at operation checks.
¨*         +      V
140
−
GYRO
Gyro sensor
(GLIDER)
WING TYPE
Function
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
  /      ! !# 
 //  ?&‹*     
   <    
This function is dedicated mixing for switching
the gyro sensitivity and gyro mode (AVCS/
NORMAL) of Futaba airplane use gyros.
'            
  !    !    
 &%   Q   z* +!         
! #           !    Š 
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "GYRO"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Gain switch selection
Each switch position
Gyro type / Gain rate
C u r r e n t s w i t c h o p e r a t i n g
direction）
● Select the setting item
with the Jog key.
（Gyro type）
● Switches to the
sensitivity setting
screen of each switch
direction when the
Jog key is pressed.
（Gyro Gain）
GYRO SENS
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
■ Gain switch selection
② Select the "SW" item and then select the
switch by pressing the + key or ‒ key.
＋
−
or
● When you do not use a function, set to the
"INH" side.
Default：SwB
■ Gyro mode and gain setting
③ UP, CNT, DWN, shows the switch position. Set the respective positional gain and mode.
Glider
Range：SwA ∼ SwD
GAIN=OFF
AVC 100%
AVCS
When a ＋ key is
pressed, gain of the
AVCS side is UP.
＋
0%
Normal
−
NOR 100%
When a − key is
pressed, gain of the
Normal side is UP.
141
AIL DIF
Aileron differential
(GLIDER)
WING TYPE
Function
Two servos can be used for ailerons and a
differential can be applied to left and right aileron
operation. The left and right aileron differential can
be adjusted independently. This function is restricted
to 2 servo aileron.
Connect the left aileron to CH1 (AIL) and the right
aileron to CH6.
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
Aileron 1
(CH1)
Aileron 6
(CH6)
'      ! !    
   !   @  
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "AIL DIF"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Aileron 1
（CH1）
rate
Aileron 6
（CH6）
rate
● Select the setting item with
the Jog key.
（Aileron rate）
L：Aileron Stick Left side rate
R：Aileron Stick Right side rate
Select the Left/Right with the
aileron stick .
Aileron Differential
Glider
■ Activating the function
① Select the "2AIL" or "2AIL1FLP"
"2AIL2FLP" by WING type (MDL
TYP).
■ Aileron rate
② Select the "AIL1" item and move the
aileron stick to the left and right and
adjust the travel of each servo by
pressing the + key or ‒ key.
＋
−
or
Range：-120 ∼ +120%
Default：+100%
● When you want to return to the initial value, press the + key
and ‒ key simultaneously. However, when the polarity is
changed only the number returns to the initial value.
（Adjust the "AIL6" item in the same way as ② .）
142
V-Tail
V-TAIL
(GLIDER)
WING TYPE
Function
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
This mixing is used with V tail aircraft that
combine the elevator and rudder functions.
CH2 (CH4)
CH4 (CH2)
(Stick mode 2)
Method
Elevator UP
Elevator DOWN
Rudder Right
Rudder Left
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "V-TAIL"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When INH is selected, the
function cannot be used. To use
the function, select ACT.
Activating the function
ELE2 rate
ELE4 rate
（Rate adjustment）
RUD2 rate
RUD4 rate
● Select the setting item with
the Jog key.
V-TAIL
＋
−
or
● When you do not use a
function, set to the "INH" side.
■ Rate adjustment
② Select the value item and then adjust
the mixing rate by pressing the + key or
‒ key.
＋
−
or
Range：-100 ∼ +100%
Default：+50%
（only ELE4 : -50%）
Glider
■ Activating the function
① Select the "MIX" item and then
select the "ACT" by pressing
the + key or ‒ key.
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.However, polarity does not
return.
NOTE：We recommend that setting be performed while moving the stick and checking the amount of movement. If
the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range
will be exceeded and a dead band in which the servo will not operate may be created.
143
BUTFLY Butterfly mixing
(GLIDER)
WING TYPE
Function
This function is utilized to quickly slow the
aircraft and reduce altitude by simultaneously
raising the left and right ailerons and lowering the
 
Butterfly (Crow) produces an extremely
,  ,    
the following:
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
|%    !Š  
~[   
            
   
<   /  !       !    
        
 Z    !      ?W$? 
    
 '          !   
!   !! 
' !!    @ 
OFF
ON
Switch set to ON
Resistance increased by raising
the elevators and lowering the
flaps
THR stick lowered
Fine tuning of an elevator
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "BUTFLY"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Amount of movement setting
● Butterfly : ACT/INH
● When MIX is set to ACT, the amount of MIX(s)
according to stick operation is displayed.
● Can be either
set to a switch
or when NULL
is controlled
by the THR
stick.
● Aileron
● Flap
● Elevator
● It can't be set.
＜ It's caused by the
wing type. ＞
● Current THR stick position
0％ : Low 100％ : High
（Currently selected condition）
Glider
● Offset setting ‒Select "OFST" XX%.
Brake amount
MAX
● Select the setting item
with the Jog key.
OFST ▶ 100%
At THR stick high
＋
press the Jog key for 1 second
Brake amount
MAX
OFST ▶60%
At THR stick 60%
press the Jog key for 1 second
● The value is changed by
+ key or ‒ key.
Start from
60%
High
Slow
THR stick operation
144
−
High
Slow
THR stick operation
● When offset is set below a center, the
mixing of THR stick operates by the high
side.
TRM MIX Trim mix
(GLIDER)
WING TYPE
Function
This function shifts the ailerons, elevator, and
      
 
switch.
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
'       /    
  
OFF
 
Aileron 1
(CH1)
ON
Flap
(CH5)
Set the switch to ON
Trim of each control surface is
moved to the set value.
Aileron 6
(CH6)
Elevator
(CH2)
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "TRM MIX"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
[TRIM MIX page1]
● When condition is used, the display
can be switched and each connection
can be set by switching the condition
switch.
● Select the setting item
with the Jog key.
＋
−
● Sets the trim neutral position of each
control surface.
Range：-100 ∼ +100
Returned to 0 by pressing the + key
and ‒ key simultaneously.
[TRIM MIX page2]
● The value is changed by
+ key or ‒ key.
● When not using this
function, select INH.
Glider
● The ON/OFF switch can be changed.
(Selected with the Jog key and
changed with the +key)
● Sets the ON/OFF direction of the
selected switch.
Activating the function
3 Position Switch
NULL
ON
ON
ON
UP
ON
OFF
OFF
2 Position Switch
NULL
UP
UP&DWN
ON
OFF
ON
UP&CNT
ON
ON
OFF
CENTER
OFF
ON
OFF
CNT&DN
OFF
ON
ON
DOWN
OFF
OFF
ON
DOWN
ON
ON
OFF
ON
OFF
ON
145
EL → CMB
Elevator → Camber mixing
WING TYPE
Function
This function is used when you want to mix the
         3  
the flaps are lowered by up elevator, and lift is
increased.
(GLIDER)
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
+; /  ?W$?   
      &Q  ?W %\W{VV]  *
' /    @ 
%            
 !      &QWƒ^*
Up the elevator
Aileron 1
(CH1)
Aileron 6
(CH6)
Flap
(CH5)
flap is down
Method
Elevator
(C )
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "EL → CMB"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
（Currently selected condition）
Mixing rate
● Select the setting item
with the Jog key.
● Aileron 1
＋
● Aileron 6
−
● Flap 5
● Flap 3
● It can't be set.
＜ It's caused by the
wing type. ＞
● The value is changed by
+ key or ‒ key.
● (RT1) and (RT2) show the
direction of elevator of
operation.
Glider
[ELE → Camber ２page]
（Currently selected condition）
● Camber MIX ACT/INH
● Can be either set to a
switch or when NULL is
always active.
● Sets the ON/OFF direction of
the selected switch.
● Described on
the next page.
146
● Current position of the
elevator stick
[ELE → Camber ２page]
● When MIX is set to ACT, the
amount of MIX(s) according to
stick operation is displayed.
● Setting that inhibits camber mixing near the elevator center position. Setting so
that camber mixing is performed only when the elevators were operated greatly
is possible.
RANGE setting
■ Setting state
① Select the "0%" item next to
RANGE with the Jog key.
■ To setting value
② Move the elevator stick to the position you
want operation to begin.
Can be either up or down. When set
to down, the up side is also set by the
same amount.
■ Set value memorization
③ Press the Jog key for 1 second.
Hold the stick in
position.


When elevator operation exceeds the range,
the stick position is displayed and mixing is
performed.
● When a RANGE number is selected and the
Jog key is pressed for 1 second, RANGE is
reset to 0% and normal mixing is performed.
Glider
● Use example of RANGE
Elevator Operation
Only an elevator moves in case of a little operation.
Elevator and flap move in case of big operation.
147
CMB MIX Camber mixing
(GLIDER)
WING TYPE
Function
This function adjusts the rate of camber
     "   #
the negative and positive directions. The aileron,
flap, and elevator rates can also be adjusted
independently and attitude changes caused by
camber operation can be corrected.
All the wing control surfaces are
lowered and the camber is increased
(lift increases)
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
*Initial setting assigns camber operation to VR.
?      !! 
>   Q{† ‡
All the wing control surfaces are
raised and the camber is
decreased (lift decreases)
Turn the VR
Attitude changes are compensated for by setting the
amount of elevator movement.
Attitude changes are compensated for by setting the
amount of elevator movement.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "CMB MIX"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
（Currently selected condition）
Sets the amount of
movement when
the VR was turned.
● Select the setting item
with the Jog key.
● Aileron 1
＋
● Aileron 6
−
● Flap 5
● Flap 3
● The value is changed by
+ key or ‒ key.
Glider
(RT1)：The amount of
operations when VR is turned to
the right.
[CMB MIX ２page]
(RT2)：The amount of
operations when VR is turned to
the left.
（Currently selected condition）
● Amount of compensation
of the elevator when the
camber changed.
● Camber MIX ACT/INH
● Can be set to operate from
a switch. When NULL, it is
operated by a VR.
148
● Sets the ON/OFF direction of
the selected switch.
AL → CMB Aileron → Camber mixing
WING TYPE
Function
*  +        
operation (stick). It is used when you want to
increase roll axis maneuverability.
(GLIDER)
1AIL 1AIL1FLP 2AIL 2AIL1FLP 2AIL2FLP
    /          
J # @ /     /      
    
Flaps and ailerons
operate
OFF
ON
Set switch to ON
Roll is corrected by using
the ailerons to control the
camber FLP.
Ailerons operation
Method
Calling the setting screen
② Select "AL → CMB"
from the menu with the
Jog key.
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Mixing rate
● When condition was used, the
display can be switched and
each connection can be set by
switching the condition switch.
Activating the function
● Select the setting item
with the Jog key.
3 Position Switch
NULL
ON
ON
ON
UP
UP&DWN
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
2 Position Switch
NULL
UP
UP&CNT
CENTER
OFF
ON
CNT&DN
OFF
ON
OFF
ON
DOWN
OFF
OFF
ON
● The ON/OFF switch can be changed.
( S e l e c t e d w i t h t h e Jog key a n d
changed with the +key)
● Sets the ON/OFF direction of the
selected switch.
DOWN
ON
OFF
ON
OFF
ON
Glider
ON
AIL → Camber mixing
■ Activating the function
① Select the "MIX" item and then select
the "ON" by pressing the + key or ‒
key.
＋
−
or
● When you do not use a function, set
to the "INH" side.
■ Mixing rate
② Select the value item and then
adjust the mixing rate by pressing
the + key or ‒ key.
＋
−
or
Range：-120 ∼ +120%
Default：0%
● When you want to return the set value to the initial value,
press the + key and ‒ key simultaneously.
149
Multicopter Function
The setting screen of each function is called from the following menu. The function when
the model type was set to multicopter (MULTI COPT) is displayed here.
Power ON
To menu screen
by holding down
the + key
（Home screen）
● When t h e E N D k e y i s
pressed, the display returns
to the home screen.
END
● When the + key is pressed for
1 second, the menu screen is
（1 second）
displayed.
＋
MENU
MENU
1/3
（Selection）
Multicopter
● Move the cursor
(highlighted) up and down
and to the left and right
with the Jog key and select
the function.
The cursor can be moved
over several pages.
MENU
2/3
（Calling the setting screen）
MENU
3/3
● Press the Jog key to open the
setting screen.
150
key ／ LCD
●＋ key
●END key
●− key
●Jog key
Refer to "Common Functions"
previously described for a
description of this function.
■ Function
◆ MENU 1/3
◆ MENU 2/3
◆ MENU 3/3
P.50
PRMTR
P.63
TIMER
P.92
MDL TYP
P.53
P.MIX
P.68
TRAINER
P.94
MDL NAM
P.55
AUX CH
P.71
FLY MOD
P.152
F/S
P.57
SERVO
P.72
CNT ALM
P.153
 POINT
P.59
TLMTRY
P.73
DR EXP
P.154
TRIM
P.60
SENSOR
P.86
THR CRV
P.156
SUB TRM
P.61
S.BUS
P.88
THR DLY
P.157
REVERS
P.62
ďź­ TRANS
P.91
GYRO
P.158
Multicopter
MDL SEL
151
FLY MOD Flight mode
(MULTICOPT)
Function
This flight mode is used for a controller of the
multi-copter connected to 6CH.
4 can be changed to a flight mode by the
chosen switch. It's used in case of a controller of
          
can be changed.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "FLY MOD"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this Function
select INH. The display of
On/Off is shown when active
and assigned to a switch.
● NOR is setting of CH6
of the state that SW is
off. 0 is usually used in
this state neutrally. Even
if the numerical value
is changed in case of
INH, movement doesn't
reflect 1-4.
Flight mode
● Select the setting item
with the Jog key.
（Activating the function）
（Switch direction）
（Switch selection）
● Priority is given to the
mode 2 when the mode
1 and 2 is turned on
simultaneously.
Multicopter
Flight mode
■ Activating the function
① Select the "INH" item of the
condition you want to use and
then set that flight mode to "ON"
or "OFF" by pressing the + key or
‒ key.
＋
−
or
● Set conditions you do not want to use to "INH".
（Changing the switch）
■ Switch selection
② Change the switch by
pressing the + key or
‒ key at the switch
selection item.
＋
−
or
■ Switch direction
③ Select the ON direction
by pressing the + key or
‒ key at the ON direction
selection item.
＋
−
or
Range：
Range：SwA ∼ SwD
Default：SwA
152
● 2P SW：NULL, UP, DOWN
● 3P SW：NULL, UP, UP&D, UP&C, CNTR, C&DN,
DOWN
CNT ALM Center alarm
(MULTICOPT)
Function
   "  #      ,    
Q /! ?W$?    
Beep sounds
When the THR stick
is set to the
specied position.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "CNT ALM"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When INH is selected, the function cannot be used. When
ON or OFF is selected, the function is activated. ON and OFF
changes are linked to the switch.
● Select the item
with the Jog
key.
● The number in parenthesis
is the current throttle stick
position.
● This is a throttle stick position alarm.
When a throttle stick was besides the slow position
and a transmitter was turned on. → Alarm start
Position setting
① Stick position is chosen by
Jog key.
OFF
② Set the throttle stick to the
position at which you want
to generate the alarm.
THR Stick
Multicopter
INH ⇔ ON/OFF
Switch selsction
Switch direction
Stick position
③ When the Jog key is held
down the alarm sounds at
that position.
Memorize the position at
which the beep is to sound.
153
DR EXP
Dual rate ／ EXPO
(MULTICOPT)
Function
D/R
The aileron, elevator and rudder channel control surface angle can be switched in 2(3) steps
'    !     @     !   '   !     
  
EXP
* 
              

                      
position. Adjustments can be made in 2(3) steps according to the control surface angle.
' ˆ;‰ / J   /
   ^ 
   /   
%      
   ! 
/     ˆ‰ / J   / /    
          ˆ‰   # 
      /   
   !  &z$*  &^  *'   !  
&  *  !      
Switch selection（SW）
Switches A to D can be selected as the aileron channel, elevator channel, and rudder channel dual rate
(exponential) switch.
z! ：Q ：% z ／ ^  ：% Q ／ ：% „
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "DR EXP"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
Multicopter
● The channel under selection is
underlined.
Channel selection
Dual rate
（Switch Direction）
EXPO
● The dual rate and exponential
settings are displayed by a
curve.
Switch selection
● Channel selection/Select
the setting item with the
Jog key.
（Switch No.）
（D/R and EXPO rate display）
Top row；Left side ／ down
Bottom row；Right side ／ up
Select the ( ← ) ⇔ ( → ) L,R/U,D
with the stick .
154
＜ Channel ＞
1：Aileron
2：Elevator
3：Throttle
4：Rudder
D/R
① A channel is chosen by Jog
key.
Range：1, 2, 4
② Adjust the rate by moving the cursor
to D/R with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：
0 ∟ 140%
Default：100%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the same
channel is possible by Jog key.
EXPO
① Select the "EXP" item and
then select the channel with
the Jog key.
② Adjust the rate by moving the cursor
to EXP with the Jog key, switching the
dual rate switch to the direction you
want to set, moving the stick to the left
(down) or right (up) side and pressing
the + key or ‒ key.
−
＋
Range：1 ∼ 4
Range：
-100 ∟ +100%
Default：0%
● When you want to
return the set value to
the initial value, press
the + key and ‒ key
simultaneously.
Adjust the rate of each direction of the dual rate switch and stick by repeating step
● Moving to another setting item of the
same channel is possible by Jog key.
① Select the "SW" item and then select
the channel with the Jog key.
② A switch is chosen by + key or -key.
＋
−
or
Range：1, 2, 4
Multicopter
Switch Change
Range：SwA ∼ SwD
155
THR CRV Throttle curve
(MULTICOPT)
Function
This function sets a 5 point throttle curve so that
the engine/motor speed relative to movement of the
         
Q  !     
 
However, this function cannot be used when the throttle EXP function was set. When this function is set,
the throttle EXP function cannot be used.
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "THR CRV"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Activating the function
Switch selection
● The set-up curve is shown
5 point curve
set
（Present switch position）
● Select the setting item
with the Jog key.
Throttle curve
Multicopter
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
● When you do not use a function, set to the
"INH" side.
■ Switch selection
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
＋
Range：SwA ∼ SwD、Default：SwC
■ 5 point curve set
③ By Jog key, either of P-1 to P-5 is chosen. The + key or - key is pressed and a
rate is set up.
Range：0 ∼ 100%
Default：P-1:0%, P-2:25%, P-3:50%, P-4:75%, P-5:100%
156
−
or
＋
−
or
THR DLY
Throttle delay
(MULTICOPT)
Function
When this function is used, the throttle operating
speed can be slowed down.
When the motor response is too sensitive, it's
used.
'  /  !   
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "THR DLY"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When INH is selected, the
function cannot be used. To use
the function, select ACT.
Activating the function
Delay Rate set
（Throttle delay rate）
● It can be set to slow the throttle
movement up to +100%
● Select the setting item with
the Jog key.
■ Activating the function
① Select the "MIX" item and then
select the "ACT" by pressing
the + key or ‒ key.
＋
−
or
■ Delay Rate set
② Select the "RATE" item and then adjust
the rate by pressing the + key or ‒ key.
＋
−
or
Multicopter
THR DELAY
Range：0 ∼ 100%
Default：0%
● When you want to return the set value to the initial value, press
the + key and ‒ key simultaneously.
● When you do not use a
function, set to the "INH" side.
157
GYRO
Gyro sensor
(MULTICOPT)
Function
This function is dedicated mixing for switching
the gyro sensitivity and gyro mode (AVCS/
NORMAL) of Futaba airplane use gyros.
'    !  Ž !   Q   
  ’     /  & #  
 J !  / #Ž  *
Method
Calling the setting screen
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
② Select "GYRO"
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
＋ （1 second）
● When not using this function,
select INH.
Gain switch selection
Each switch position
Gyro type / Gain rate
C u r r e n t s w i t c h o p e r a t i n g
direction）
● Select the setting item
with the Jog key.
（Gyro type）
● Switches to the
sensitivity setting
screen of each switch
direction when the
Jog key is pressed.
（Gyro Gain）
GYRO SENS
Multicopter
■ Activating the function
① Select the "MIX" item
and then select the
"ON" by pressing the +
key or ‒ key.
＋
−
or
■ Gain switch selection
② Select the "SW" item and then select the
switch by pressing the + key or ‒ key.
＋
−
or
● When you do not use a function, set to the
"INH" side.
Range：SwA ∼ SwD
Default：SwB
■ Gyro mode and gain setting
③ UP, CNT, DWN, shows the switch position. Set the respective positional gain and mode.
GAIN=OFF
158
AVC 100%
AVCS
When a ＋ key is
pressed, gain of the
AVCS side is UP.
＋
0%
Normal
−
NOR 100%
When a − key is
pressed, gain of the
Normal side is UP.
TX SETTING
The settings here are special settings that are unnecessary during normal use. The stick mode can be
changed and stick adjustment (calibration), throttle lever reverse, and language can be set.
Turn on the power switch with the + key
and ‒ key pressed in the power off state. The
screen shown at the left appears. To return
to the home screen, turn off the power
and then turn the power back on without
pressing the keys.
7;6(77,1*
67.02'(
67.$'7+55(9
1(;7
125
/$1*8$*(
(QJOLVKá´ž
■ STK-MODE
AIL
RUD
ELE THR
THR ELE
MODE 1
RUD
AIL
AIL
RUD
MODE 2
RUD
AIL
ELE THR
This is the MODE1 ∟ MODE4 setting. The
initial state is MODE2. To change the mode
the stick ratchet must be changed. Request
that this be done by Futaba Service. (Charged
modication)
THR ELE
MODE 4
MODE 3
■ STK-ADJ
This function is normally not used. If stick deviation should occur, make this adjustment.
Do not use it in the normal state.
Calling the setting screen
① Turn off the power and then
turn the power back on while
pressing the + key and ‒ key
simultaneously.
＋
② Select STK-ADJ → NEXT
in the menu with the Jog
key.
③ Enter the setting screen by
pressing the Jog key.
② Press the Jog key down
and select NEUT ■ .
③ Set the stick to the neutral
position and press the Jog
key.
−
Stick adjustment
① Select the stick you want to
adjust with 1 ∟ 4 with the +
key.
＋
159
④ Swing the selected stick fully
to the left and right (up and
down).
⑤ ■ appears next to "LEFT"
and "RGHT". Press the Jog
key.
⑥ When "COMPLETE" is
displayed, adjustment is
complete.
END
■ THR-REV
This function is not used. When you want to use full throttle with the throttle stick down
and slow with the throttle stick up, select REV. When the stick is up, trim is effective and
when the stick is down, trim is not effective.
*Throttle servo operation reversed by the linkage is usually performed by reverse in the
normal menu. When throttle servo operation is reversed with the THR-REV function, trim
becomes ineffective at slow.
THR-REV
① Turn off the power and then
turn on the power while
pressing the + key and ‒ key
simultaneously.
＋
② Select THR-REV → NOR
in the menu with the Jog
key.
③ Select NOR or REV by
pressing the + key or ‒ key.
Setting is ended by power
off.
＋
−
−
■ LANGUAGE
The language displayed at proportional can be changed. The initial setting is English, but
can be selected from among 7 languages.
LANGUAGE
① Turn off the power and then
turn on the power while
pressing the + key and ‒ key
simultaneously.
＋
② Select
LANGUAGE → English in
the menu with the Jog
key.
③ Select NOR or REV by
pressing the + key or ‒ key.
Setting is ended by power
off.
＋
−
−
Return from the transmitter setting screen to the normal menu by turning on the power
without pressing a key.
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
2015, 5 (1)
160

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Keywords                        : 
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2015:06:25 17:20:16+08:00
Modify Date                     : 2015:06:25 17:22:39+08:00
Metadata Date                   : 2015:06:25 17:22:39+08:00
Document ID                     : uuid:F5BDE7611B1BE5118FEE9BA4EF790A8E
Instance ID                     : uuid:994ce3c1-1b2b-4812-9cc6-6ad542ddce8d
Derived From Instance ID        : uuid:4e4000fd-96f6-4838-bd7d-a88d911e7961
Derived From Document ID        : uuid:5413fa09-3bdd-46df-a2b8-ccf79273561e
Format                          : application/pdf
Description                     : 
Creator                         : minchih
Title                           : MANUAL_6K(E)_0521.pdf
Has XFA                         : No
Page Count                      : 80
Subject                         : 
Author                          : minchih

EXIF Metadata provided by EXIF.tools