GEMMY 113341 Orchestra of Lights-Lightshow Tree and Speaker User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3907344
Application ID	p6bEcLQhNaZdFCgI7+IWKA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.18kB (539783 bits)
Date Submitted	2018-06-29 00:00:00
Date Available	2018-06-29 00:00:00
Creation Date	2018-06-20 19:34:34
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-06-29 09:41:42
Document Title	User manual
Document Creator	Adobe InDesign CC 13.0 (Macintosh)

Orchestra of LightsLightshow Tree and Speaker
SAFETY INFORMATION
WA R N I N G : R E A D A N D U N D E R S TA N D A L L
INSTRUCTIONS.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious
personal injury.
ELECTRIC PRODUCT. Keep away from children. Not recommended for children
WARNING:
under 3 years of age. As with all electrical products, precautions should be observed during handling
and use to reduce the risk of electric shock. If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. To avoid
the risk of electrical shock, always make sure the figure is unplugged from the electrical outlet before
assembling, disassembling, or relocating.
WARNING: This product is to be assembled by adults only.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed, including the following:
•T
 his is an electrical product - not a toy! To avoid risk of fire, burns, personal injury, and electric
shock, it should not be played with or placed where small children can reach it.
• Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
•T
 his seasonal use product is not intended for permanent installation or use.
•D
 o not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of
heat.
•D
 o not secure product wiring with staples or nails or place on sharp hooks or nails.
•D
 o not let lamps rest on the supply cord or on any wire.
•U
 nplug the product when leaving the house, when retiring for the night, or if left unattended.
•D
 o not use this product for other than its intended purpose.
•D
 o not hang ornaments or other objects from cord, wire, or light string.
• Do not close doors or windows on the product, or extension cords, as this may damage the wire
insulation.
•D
 o not cover the product with a cloth, paper, or any material not part of the product when in use.
•D
 o not place the product against carpeting, furniture, or any other fabric when in use.
•R
 ead and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
SAFETY INFORMATION
CAUTION
This d evice complies with P art 15 o f the FCC Rules. O peration is subject to t he f ollowing t wo
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION:
compliance could void the user’s authority to operate the equipment.
T his equipment has been t ested and f ound t o comply w ith the limits for a Class
NOTE:
B digital device, pursuant to P art 15 o f the FCC Rules. These limits are designed t o provide
reasonable protection against harmful i nterference in a r esidential i nstallation. This equipment
generates, uses, and c an r adiate radio frequency energy and, if n ot i nstalled and u sed in
accordance w ith the instructions, may cause harmful i nterference to r adio communications.
Howeve r, t here is n o guarantee that i nterference will n ot o ccur i n a particular i nstallation. If
this equipment does cause harmful i nterference to r adio or t elevision reception, which c an b e
determined b y turning the equipment off and o n, t he user i s encouraged t o try to correct t he
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15-20 minutes.
PACKAGE CONTENTS
PART
DESCRIPTION
F/G
QUANTITY
Base				
Support Rings 			
Controller 			
Plastic covers			
Base Connector ring
Star Topper with Light Strings
PART
QUANTITY
Speaker stake			
Speaker
UL-listed Adaptor			
Metal stakes
Poles				
DESCRIPTION
ASSEMBLY INSTRUCTIONS
1. Set bases (A) out in a clear and flat area. Unfold each base (A)
to allow it to stand up.
2. Attach support rings (B) on each base (A).
3.Use controller ( C ) for the larger tree and begin attaching the
plastic covers (D) and place over base (A). Attach plastic covers
(D) for the smaller tree and place over base (A).
4. Attach base connector ring ( E ) over the top of the assembled
base.
ASSEMBLY INSTRUCTIONS
5. Assemble 2 support poles (L) for the larger tree and 1 support
pole (L) for the smaller tree.
6. Begin staking each tree into ground using the metal stakes (K).
7. Take the Star Topper marked “F” and place on the taller
support pole (L). Take the Star Topper marked “G” and place
on the shorter support pole (L).
8. Carefully drape light strings down toward the ground based
on their number order in a clockwise direction. Use the plastic
clip to secure the light strings to the arched areas along the
support ring (B), being careful to secure them in a clockwise
numbered order. Tighten each with the cinch clip until taught.
ASSEMBLY INSTRUCTIONS
9. Connect the two trees together by attaching the cables.
10. Connect the UL listed adapter (J) to the main control box.
10
11. Connect the speaker wire to the control box.
11
12. Slide stake into the bottom of the speaker and insert into
ground.
12
CARE AND MAINTENANCE
• When the product is placed on a live tree, the tree should be well-maintained and fresh. Do not
place on live trees in which the needles are brown or break off easily. Keep the tree holder filled
with water.
• If the product is placed on a tree, the tree should be well-secured and stable.
• Before using and reusing, inspect the product carefully. Discard any products that have cut,
damaged or frayed wire insulation cords, cracks, lamp holders or enclosures, loose connections, or
exposed copper wire.
• When storing the product, carefully remove the product from wherever it is placed, including trees,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections
and wires.
• When not in use, store neatly in a cool, dry location protected from sunlight.
• Do not discard box as it should be used for storage.
• Return all parts to the original packaging, if possible.
•T
 he remote control is not weatherproof. Please operate and store in a dry environment.
TROUBLESHOOTING
If you have any questions regarding the product, please call customer service at 1-877-250-9032,
9 a.m. - 5 p.m., CST, Monday-Friday.
The product is 1. T h e p o w e r s o u r c e m a y
be disabled or the cord is
not operating
unplugged.
properly.
1. Check all power cords to ensure that they
are properly connected.
THESE INSTRUCTIONS ARE FOR THESE ITEM NUMBERS
113341
QD ID：91274
Visit WWW.GEMMY.COM for more information.
©2018 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 (877) 250-9032
MADE IN CHINA / PRINTED IN CHINA

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2018:06:20 19:34:34+08:00
Creator                         : Adobe InDesign CC 13.0 (Macintosh)
Modify Date                     : 2018:06:29 09:41:42+08:00
Has XFA                         : No
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:47e9356f-0095-4dbd-927c-0637f2206826
Original Document ID            : adobe:docid:indd:c0d6b7d0-8648-11df-81ea-e04dc8a0db03
Document ID                     : xmp.id:111c669e-1dec-4f26-a3fd-e2ed4c4be5a4
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4cc0a593-364c-4820-9b9e-06ef375d0435
Derived From Document ID        : xmp.did:4cc0a593-364c-4820-9b9e-06ef375d0435
Derived From Original Document ID: adobe:docid:indd:c0d6b7d0-8648-11df-81ea-e04dc8a0db03
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.0 (Macintosh)
History Changed                 : /
History When                    : 2018:06:20 19:34:34+08:00
Metadata Date                   : 2018:06:29 09:41:42+08:00
Creator Tool                    : Adobe InDesign CC 13.0 (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 7

EXIF Metadata provided by EXIF.tools