GIGA TMS UM800L UHF RFID Reader Module User Manual Visio UM800L MENU 20150511 vsd

GIGA-TMS INC. UHF RFID Reader Module Visio UM800L MENU 20150511 vsd

Users Manual

Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:. Reorient or relocate the receiving antenna.. Increase the separation between the equipment and receiver.. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.. Consult the dealer or an experienced radio/TV technician for help.FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: “Contains FCC ID: __ WXAUM800L___””End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
FEATURESPIN DIAGRAMSAPPLICATIONSTop View34-PIN SMD1213141530292827PIO3PIO2PIO1PIO4GNDGNDGNDANTGIGA-TMSP R O M A GUM800LEmbedded UHF RFID Read/Write Module DESCRIPTIONAccess Control SystemSecurity System RFID PrinterMobile PhonePoint of SalePatrol SystemUM800L is a compact and practical embedded UHF reader module which compliant with EPC Global Class1 Gen2. With small dimensions (30x20x3.6mm) and low power consumption ( 380mA, 27dBm for output) make UM800L an ECO friendly choice for your system.With adjustable frequency (840~960 Mhz), adjustable transmit output (10 to 27dBm), optional interface (USB or UART TTL) and 14 GPIO enable you the flexibility for various applications under different environments.UHF is one of the best solutions for middle and long range RFID applications.Such as access control, parking, logistic and vehicle tracking etc.Using UM800L, you can extend the wonderful experience to portable or mobile devices.GIGA-TMS makes what you need and customizes what you want.Low cost ,Small Outline 30x20x3.6mmCompliant with EPCglobal Class1 Gen2 (ISO18000-6C)Operating Frequency 840 ~ 960 MHzAdjustable Transmit Output Power from +10 to +27dBmOperate voltage range 2.7~5.0 VLow power consumption: 50mA@ standby, 380mA @27dBm OutputUSB HID or UART TTL Interface14 GPIO for Customize Application No RF Connect and Cable requestSupport In-System Programmable and Self Firmware UpdateProvides Development Kit - UM800LDKCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW PreliminaryPIN #1IDENTIFY31GND11PIO5910PIO6PIO78PIO83332 GNDVDD34GNDUM800LPortable Battery Device12345671617242322212019182526RXDTXDD+D-/RSTC2DC2CKPIO11GNDGNDPIO12PIO13PIO9PIO10VRFPIO0 GNDGND
UM800LCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW PreliminaryFUNCTION DESCRIPTIONPIN FUNCTIONSTop View Bottom ViewUART asynchronous input.USB Differential Plus Line ( Option )[ Note 1 ] I: Input , O: Output , I/O : Input or Output , P: Power , A: AntennaUART asynchronous transmit.D+C2DPIO2PIO8PIO7PIO6/RSTC2CKPIO3PIN NAMETXDRXDPIO4PIO5D-GNDPIO1I/OI/OI/OI/OI/OI/OPI/OI/OI/OOII/OI/OI/OI/OI/O1PINUSB Differential Minus Line ( Option )Reset PinGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentISPPower GroundGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentISPPIO0GPIO , 5 V tolerant with high sink currentP2678910131453121141532~3316PVRFPA Power Supply Input 3.0~5.0v +/- 5% ( 5V Full power for 27dBm )17PIO11PIO10I/OI/OI/OGPIO , 5 V tolerant with high sink currentGPIO , 5 V tolerant with high sink currentPIO9GPIO , 5 V tolerant with high sink current181920PGNDPower Ground23~30ANT AConnect To Antenna 31VDD P2.7V~3.6V power supply (For optimal power supply rejection and performance a supply voltage of at least 3.3V is required.)34Pin1PIO13I/OI/OGPIO , 5 V tolerant with high sink currentPIO12GPIO , 5 V tolerant with high sink current2122GIGATEKMODEL NO.:UM800LPART NO.:UM800L-00FCC ID : WXAUM800LMFG. NO.:REV.XXXXX XXX XXXXmade in Taiwan
UM800LCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW PreliminaryAPPLICATION CIRCUITVbusD-D+GNDUSB1213141530292827PIO3PIO2PIO1PIO4GNDGNDGNDANT 31GND11 PIO5910 PIO6PIO78PIO83332GNDVDD 34GNDUM800L12345671617242322212019182526RXDTXDD+D-/RSTC2DC2CKPIO11GNDGNDGNDGNDPIO9PIO10VRFPIO0 GNDGNDVRFVinTXDRXDGNDUART TTLVRFAntenna/RSTC2DC2CKGNDISP50 ohm RF track1. VRF = 3.0~5.0V +/- 5% (5.0V Full Power Output)[ Note ]2. VDD = 2.7~3.6V +/- 5%*Note1*Note1*Note1LpVRFVDDVDDVRFLow-Dropout RegulatorVDD*Note1*Note 2VDD
34-Pin SMD PackageDimensions in Millimeters UM800LCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW PreliminaryPACKAGE DESCRIPTIONSPECIFICATIONSPOWER REQUIREMENTS 3.0V ~ 5.0V regulated for VRF. A linear regulator is recommended.2.7V ~ 3.6V regulated for VDD.CURRENT CONSUMPTION 380 mA @ 27dBm RF Power OutputHOST INTERFACE UART ( Default : 115200 Baud rate ) ProgrammableUSB HIDFREQUENCY 840 ~ 960MHz DEMODULATION PRASKCONFIGURE INTERFACE UART , 115200 bps, 8N1 DIMENSIONS 30 x 20 x 3.6 mmWEIGHT < 10 gmENVIRONMENT Operating Temp : -0℃~ +60℃Humidity : 10 ~ 90 % Non-condensingSUPPORT EPC DRM YesRFID PROTOCOL SUPPORT EPC Class 1 Gen 2, ISO18000-6CDATA ENCODING FM0 or Miller codeBIT RATE Supports uplink data rate of 40,160,320 KbpsTX OUTPUT POWER 10 ~ 27 dBmANTENNA TYPE Mono-staticINPUT / OUTPUT PIN Programmable 12 Input / Output Pin by Customer25188Top View3020PIN12.54 T=0.83.2
UM800LCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW PreliminaryExample Board LayoutPackage Drawings and MarkingsUM800GIGATEKMODEL NO.:UM800LPART NO.:UM800L-00FCC ID : WXAUM800LMFG. NO.:REV.XXXXX XXX XXXXmade in Taiwan
Reflow ProfileUM800LCopyright 2012 by GIGA-TMS Corporation. HTTP://WWW.GIGATMS.COM.TW Preliminary

Navigation menu