GUANGZHOU TAIMA TI4520 Wireless 2D Barcode Scanner User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3421900
Application ID	bt1YcLQgxs8M1UM2TJHCKA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.45kB (418077 bits)
Date Submitted	2017-06-12 00:00:00
Date Available	2017-06-12 00:00:00
Creation Date	2017-03-20 10:37:53
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2017-05-24 10:37:10
Document Title	User Manual
Document Creator	Acrobat PDFMaker 11 Word 版
Document Author:	微软中国

Handset & Cradle
Installation
Step 3. Press the cradle①(P button) and hold till the Dee-Doo-Doo
sound is out. Then the handset and cradle are well paired.
Connection and Pairing
2D Wireless Barcode Scanner
Remark: 1 cradle can support maximum 100 handsets. The handset
Step 1. Refer to the below pictures, firstly connect the cradle⑧ to host
cannot upload data if the handset and cradle were not well paired.
(e.g. PC or POS) with cables of different interface：
Quick Guide
Usage of Scanner
USB: Plug the RJ45 in cradle⑧, and plug the USB end into the host.
Power On / Off
RS232 Cable
Typically the cradle will auto identify the interface type (COM) and
cradle⑤ gets green on. In extreme case the cradle fails to identify
(green flash of cradle⑤), please scan the barcode to set it manually.
Auto identifying (Default)
① Power Indicator
③ Trigger
② Data Indicator
④ View window of capture
out, the handset is power on. If handset is not used for 60sec (default),
the handset will auto turn off. The timing can be reset to your need.
Code capture
In the standby mode, pull the trigger to capture code. Make sure the
USB Mode
USB Cable
When trigger (handset①) is pulled and a Beep-Deep sound comes
green aiming line is covering the full code, as in picture below
Correct way
Keyboard (PS/2) Mode
Keyboard PS/2：Plug the RJ45 to cradle⑧, and connect the male PS/2
end to host port and the female end with keyboard wire.
RS232 Mode
Wrong way
Note: The auto setting of interface type will only be activated when
the pairing is well done. Please refer to the Step2 and Step3 for pairing.
Step 2. Place the handset onto the cradle. As in the picture below, firstly
place the head of handset onto the wider end of cradle. Then press the
other end onto the cradle till a “Pa” sound is out. It means well locked.
Reset to Default
Remark: 1.Once the code is well captured, the handset② will turn red
and up for 1sec, and a “Dee” sound will come out.
2. To capture codes of different density, please move the handset
forward and backward to gain a proper position.
Keyboard P/S 2
Remark：This pamphlet is for quick guidance only. Please refer to
the Uses’ Manual for more detail instructions.
VER: TI4520_QG_EN_V1.00
① Pairing
⑥ Reserved
② Channel Up
⑦ Power Interface
③ Channel Down
⑧ Data Interface to PC
④ Power Indicator
⑨ Wall-mounted Adjusting
⑤ Data Indicator
⑩ Antenna
Recharging
RS232：Plug the RJ45 into the cradle⑧, and plug the RS232 into the PC
Place the handset back to cradle as Step2 to start recharging.
port. The DC power should be plugged into the RS232 connector.
Remark: 1. Green flash of handset① means low power.
2. Red flash means recharging and it turns to yellow on once finished.
Handset onto Cradle
Built-in Data Memory
If the handset is out of limit to wireless contact radius, or it works in
code data will be ignored and alarm of “Dee-Dee-Dee” will come out.
LF
Auto Storage Mode (Default): The data will be stored in the handset
CR+LF
the Manual Upload Mode, the captured code data will be stored in the
memory in case of upload failure to cradle. And the data will be
handset memory. The Data Indicator (handset②) will be red on if data
uploaded to cradle once the contact connection come back normal. It’s
stored. It will turn green on once the data is well uploaded.
the default working mode.
Manual Mode: The code data will firstly be stored in the built-in
No Suffix
Multi-Cradles Working
handset memory once well captured. It can store up to 10,000pcs code
In case two or more cradles working in the same room, please set
the channel will be displayed on the PC.)
2．Redo the pairing of handset and cradle to reset it to new channel.
Upload Start Code is manually triggered.
Setting the Torch
Indicators
Caution: Please check with your local authority and set the power of
wireless communication according to local rules and regulations.
Loud (default)
Upload Start code is triggered, all code data stored in handset will be
Torch off
will slow down upload speed. However, they won’t jam with each other.
uploaded again.
Status
Meanings
Green
Started normally
Power
Green flash
Power low, need to recharge
(handset①)
Red flash
Recharging
Yellow
Recharge finished
Green
All data uploaded
Data
Red
Stored data pending to upload
(handset②)
Red flash
Data storage is full
Yellow flash
Data is uploading
Mid
Possibility of upload failures: Cradle disconnected to PC; Exceeding
Auto Storing (Default)
No Storing
Start QR
Firmware Version
distance limit; Handset working in Manual Mode (e.g. checking stock).
Low
Common Symbol Setting
Information Check
Handset Indicators
Power-Low（0dBm）
Setting the Volume of the Beeper
During the process of uploading or after upload well finished, if the
Torch on when scanning*
Remark: If two or more cradles working in the same signal channel, it
Common Settings
Indicators and Buttons
data. The data would be uploaded to cradle in one time once the
them to different channels to ensure high upload efficiency as follow.
1．Press the “+” or “-” buttons (Cradle②, ③) on the cradle. (The No. of
Power-Mid (7dBm)
Mute
Manual Mode
Setting the Scanning Mode
Stop QR
Upload Start (in Manual Mode)
Handset Serial No.
Manual Scanning*
Start Data Matrix
Auto Scanning Mode
Cradle Serial No.
Stop Data Matrix
data stored in handset will be uploaded again. To avoid duplicating
Start PDF417
upload data, please trigger Erase Storage code to clear handset data.
Channel and Handset ID
Stop PDF417
Erase Storage
Indicators
CR (Default)
Setting the Data Upload Mode
Multiple upload modes are available for different usages:
No Storing Mode: Every code data will be uploaded instantly to the
Flashing
Identifying interface
(Right, Green)
Green on
Started normally
Data -Cradle⑤
Red flash
Receiving data
(Middle, Red)
Red on
Stored data pending to upload
Rev
-Cradle⑥
cradle once they are well captured. In case of unsuccessful upload, the
Reserved
Cradle Button
Power Off
Power off at once
Button
Position(Button)
Function
Channel
Cradle③
For channel setting. One press to
Down
Setting Power of Wireless Communication
Power-High (Default 14dBm)
Meanings
Power -Cradle④
Pairing
Suffix Quick Setup
Status
(Left, Green)
Remark: In the Manual Mode, all stored code data will be kept until
manually erased. Every time the Upload Start code is triggered, all code
Battery Power
Cradle Indicators
Channel
Up
Right (-)
Cradle①
Mid (P)
Cradle②
Left (+)
turn down one channel
Press and hold 4secs to pair the
handset and cradle. Once it’s
done, “Dee-Doo-Dee” alarm will
For channel setting. One press to
turn up one channel
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 微软中国
Create Date                     : 2017:03:20 10:37:53+08:00
Modify Date                     : 2017:05:24 10:37:10+08:00
Has XFA                         : No
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:05:24 10:37:10+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:1939a6c5-8e40-43b5-89cc-fb5f798dbd15
Instance ID                     : uuid:61600916-b067-454c-9eff-09a18cc8bcd4
Subject                         : 4
Format                          : application/pdf
Creator                         : 微软中国
Producer                        : Adobe PDF Library 11.0
Source Modified                 : D:20170318034458
Company                         : Microsoft
Page Layout                     : OneColumn
Page Count                      : 3

EXIF Metadata provided by EXIF.tools