Contents
- 1. Users Manual-statements
- 2. Users Manual
Users Manual
®
FUSION® A-Class Infotainment System
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Failure to follow these cautions could result in damage to the
vehicle or poor product performance.
This device must be installed according to these instructions.
Disconnect the vehicle's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded according to the installation instructions.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact FUSION Product Support.
Installing the Infotainment System
1If necessary, remove the dashboard bezel around the stereo
or stereo installation location.
2If necessary, remove the existing stereo or infotainment
system.
3Insert the included bracket À into the dashboard Á.
4Secure the bracket to the dashboard using screws (not
included) through the inner holes Â.
5Connect the included wiring harnesses to the vehicle wiring
harness and other A/V connectors as needed.
You can consult the wiring diagrams to identify specific
connectors and wires (Wiring Harnesses, page 1).
6Route all harnesses and other wiring through the opening in
the bracket, and make all necessary wiring connections to
the back of the infotainment system (Connector Identification,
page 1).
7Insert the infotainment system à into the bracket.
8Secure the infotainment system to the bracket and
dashboard using screws (not included) through the outer
holes Ä.
9Install the included dashboard bezel around the infotainment
system.
Connector Identification
Item Connector Notes
ÀUSB This connector is compatible with the two
included USB cables.
ÁGPS This port is for the included active GPS
antenna.
ÂAM/FM antenna You may need the included antenna
connector adapter to connect the vehicle
antenna to the system.
ÃPrimary wiring
harness
This harness contains power and speaker
wiring.
ÄSecondary wiring
harness
This harness contains additional audio/
video connectors.
Wiring Harnesses
Primary Wiring Harness
The primary wiring harness contains the main power and
speaker connections for the system. The harness connects
directly to the stereo and to the vehicle wiring harness without
modification. You can use this diagram to troubleshoot or to
address non-default installation requirements.
NOTE: The power and rear speaker wires in the wiring harness
have inline connectors. These connectors can be used when
you need an alternative power source to power the infotainment
system, or when the vehicle ISO 10487 connector does not
connect to the rear speakers.
March 2016 Printed in Taiwan 190-02062-02_0A
Item Description
ÀVehicle ISO 10487 standard wiring harness connector
Á and ÂInfotainment system connectors
Wire Color Wire Function
Red 12 Vdc battery (constant)
Yellow 12 Vdc battery (switched)
Black Ground
Orange Illumination
Blue Antenna power
Gray Speaker, front right +
Gray/black Speaker, front right -
White Speaker, front left +
White/black Speaker, front left -
Purple Speaker, rear right +
Purple/black Speaker, rear right -
Green Speaker, rear left +
Green/black Speaker, rear left -
Secondary Wiring Harness
The secondary wiring harness contains various audio and video
input and output connections. The harness connects directly to
the stereo without modification. You can use this table to
troubleshoot or to identify the functions of the audio and video
connectors.
Connector Label Function Notes
ÀRVC
VIDEO
Camera video
input
Used for rear view camera
input only.
ÁVIDEO
OUT
Video output Provides composite video out
for an external monitor.
ÂN/A CAN
connector
Connects directly to a CAN
BUS or to a PSM connector
using one of the included
cables.
ÃSUB L/R Subwoofer
ouput
Connects to a powered
subwoofer. The white
connector is the left channel,
and the red connector is the
right channel.
ÄN/A SiriusXM®Connects to a SiriusXM
module and antenna.
ÅAUX IN
L/R
Auxillary
audio input
Connects to a general stereo
audio input. The white
connector is the left channel,
and the red connector is the
right channel.
About the CAN Connection
Two cables are supplied to connect the infotainment system to
the vehicle CAN bus, either through a Parameterizable Special
Module (PSM) or directly to the vehicle CAN bus. When a PSM
is available and has been programmed with software that
supports this infotainment system, the PSM connection is
preferred. If there is no PSM, or if the PSM is not programmed
appropriately, the direct CAN connection should be used.
NOTE: You must use only one of the supplied cables to connect
the infotainment system to the vehicle CAN bus.
Connecting the Infotainment System to a PSM
You can use the included cable to connect the infotainment
system to a PSM on a compatible vehicle.
1Locate the PSM connector in the vehicle.
The PSM connector is typically located under the front left
seat (the driver's seat in the United States).
2Route the single connector on the PSM cable À to the
secondary wiring harness of the infotainment system, and
route the double connector on the PSM cable Á to the PSM.
3Connect the single connector on the PSM cable to the CAN
connector on the secondary wiring harness of the
infotainment system.
4Insert the two pin connectors into plug 2 of the PSM
connector according to the diagram and table.
Item Wire Color PSM Pin
ÂBrown/red 18
ÃBrown 15
Connecting the Infotainment System to a CAN Bus
You can use the included cable to connect the infotainment
system directly to a CAN bus distributor on a compatible vehicle.
1Locate the CAN bus distributor À in the vehicle.
The CAN bus distributor is located behind the dashboard on
the left side (the driver's side in the United States).You must
remove the panel on the left side of the dashboard (between
the dashboard and the door frame) to access it.
2Route the harness connector on the CAN cable Á to the
secondary wiring harness of the infotainment system, and
route the other connector on the CAN cable  to the CAN
bus distributor behind the dashboard.
3Connect the cable to the CAN connector on the secondary
wiring harness of the infotainment system.
2 FUSION A-Class Infotainment System Installation Instructions
4Connect the cable to the CAN bus distributor behind the
dashboard.
5Test the CAN functionality on the infotainment system.
6Select an option:
• If the infotainment system does not recognize the CAN
connection, unplug the connector from the CAN bus
distributor, rotate it 180 degrees, reconnect it, and repeat
step 5.
• If the infotainment system recognizes the CAN
connection, secure the cable and continue with the
installation of the infotainment system.
Specifications
Specification Value
Input voltage 12 Vdc
Current (max.) 12 A
Output power 26 W x 4 channels (typical)
40 W x 4 channels (max.)
Temperature range From -10° to 70°C (from 14° to 158°F)
Radio FM: 87.70 to 107.90 MHz
AM: 522 to 1611 kHz
Physical inputs and
connections
Input: microSD™ (front), hdmi (front), USB
(rear), AUX-in (RCA L\R, secondary harness),
AV-in (rearview camera, secondary harness),
SiriusXM (secondary harness), CAN
(secondary harness)
Output: AV-out (composite, secondary
harness), subwoofer (secondary harness)
Wireless connections 2.4 GHz Bluetooth®, Wi‑Fi®, and Wi‑Fi
CERTIFIED MiraCast™
Garmin®, the Garmin logo, FUSION®, and the Fusion logo are trademarks of Garmin Ltd.
or its subsidiaries, registered in the USA and other countries. These trademarks may not
be used without the express permission of Garmin.
Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Garmin is under license. microSD™ and the microSD logo are trademarks
of SD-3C, LLC. Sirius, XM and all related marks and logos are trademarks of Sirius XM
Radio Inc. Wi‑Fi® is a registered mark of Wi-Fi Alliance Corporation. Wi‑Fi CERTIFIED
MiraCast™ is a trademark of Wi-Fi Alliance Corporation. Other trademarks and trade
names are those of their respective owners.
FUSION A-Class Infotainment System Installation Instructions 3
© 2016 Garmin Ltd. or its subsidiaries www.garmin.com/support