Garmin 02324 Head Unit User Manual

Garmin International Inc Head Unit Users Manual

Contents

Users Manual

Download: Garmin 02324 Head Unit User Manual
Mirror Download [FCC.gov]Garmin 02324 Head Unit User Manual
Document ID2936343
Application ID05KC932GLEh6ynfH79gH0w==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize39.72kB (496438 bits)
Date Submitted2016-03-21 00:00:00
Date Available2016-03-22 00:00:00
Creation Date2017-11-21 14:53:44
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-21 14:53:44
Document TitleUsers Manual
Document CreatorAH XSL Formatter V6.2 MR5 for Windows (x64) : 6.2.7.18952 (2014/11/12 16:18JST)

®
FUSION A-Class Infotainment System
Installation Instructions
®
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Failure to follow these cautions could result in damage to the
vehicle or poor product performance.
This device must be installed according to these instructions.
Disconnect the vehicle's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded according to the installation instructions.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact FUSION Product Support.
8 Secure the infotainment system to the bracket and
dashboard using screws (not included) through the outer
holes Ä.
Install
the included dashboard bezel around the infotainment
system.
Connector Identification
Installing the Infotainment System
1 If necessary, remove the dashboard bezel around the stereo
or stereo installation location.
2 If necessary, remove the existing stereo or infotainment
system.
3 Insert the included bracket À into the dashboard Á.
Item Connector
4 Secure the bracket to the dashboard using screws (not
included) through the inner holes Â.
5 Connect the included wiring harnesses to the vehicle wiring
harness and other A/V connectors as needed.
You can consult the wiring diagrams to identify specific
connectors and wires (Wiring Harnesses, page 1).
Route
all harnesses and other wiring through the opening in
the bracket, and make all necessary wiring connections to
the back of the infotainment system (Connector Identification,
page 1).
7 Insert the infotainment system à into the bracket.
March 2016
Notes
À
USB
This connector is compatible with the two
included USB cables.
Á
GPS
This port is for the included active GPS
antenna.
Â
AM/FM antenna
You may need the included antenna
connector adapter to connect the vehicle
antenna to the system.
Ã
Primary wiring
harness
This harness contains power and speaker
wiring.
Ä
Secondary wiring
harness
This harness contains additional audio/
video connectors.
Wiring Harnesses
Primary Wiring Harness
The primary wiring harness contains the main power and
speaker connections for the system. The harness connects
directly to the stereo and to the vehicle wiring harness without
modification. You can use this diagram to troubleshoot or to
address non-default installation requirements.
NOTE: The power and rear speaker wires in the wiring harness
have inline connectors. These connectors can be used when
you need an alternative power source to power the infotainment
system, or when the vehicle ISO 10487 connector does not
connect to the rear speakers.
Printed in Taiwan
190-02062-02_0A
Item
Description
À
Á and Â
Vehicle ISO 10487 standard wiring harness connector
Infotainment system connectors
Wire Color
Wire Function
Red
12 Vdc battery (constant)
Yellow
12 Vdc battery (switched)
Black
Ground
Orange
Illumination
Blue
Antenna power
Gray
Speaker, front right +
Gray/black
Speaker, front right -
White
Speaker, front left +
White/black
Speaker, front left -
Purple
Speaker, rear right +
Purple/black
Speaker, rear right -
Green
Speaker, rear left +
Green/black
Speaker, rear left -
Secondary Wiring Harness
The secondary wiring harness contains various audio and video
input and output connections. The harness connects directly to
the stereo without modification. You can use this table to
troubleshoot or to identify the functions of the audio and video
connectors.
Connector Label
Function
Notes
À
RVC
VIDEO
Camera video Used for rear view camera
input
input only.
Á
VIDEO
OUT
Video output
Provides composite video out
for an external monitor.
Â
N/A
CAN
connector
Connects directly to a CAN
BUS or to a PSM connector
using one of the included
cables.
Ã
SUB L/R
Subwoofer
ouput
Connects to a powered
subwoofer. The white
connector is the left channel,
and the red connector is the
right channel.
Ä
N/A
SiriusXM
Connects to a SiriusXM
module and antenna.
Å
AUX IN
L/R
Auxillary
audio input
®
Connects to a general stereo
audio input. The white
connector is the left channel,
and the red connector is the
right channel.
About the CAN Connection
Two cables are supplied to connect the infotainment system to
the vehicle CAN bus, either through a Parameterizable Special
Module (PSM) or directly to the vehicle CAN bus. When a PSM
is available and has been programmed with software that
supports this infotainment system, the PSM connection is
preferred. If there is no PSM, or if the PSM is not programmed
appropriately, the direct CAN connection should be used.
NOTE: You must use only one of the supplied cables to connect
the infotainment system to the vehicle CAN bus.
Connecting the Infotainment System to a PSM
You can use the included cable to connect the infotainment
system to a PSM on a compatible vehicle.
1 Locate the PSM connector in the vehicle.
The PSM connector is typically located under the front left
seat (the driver's seat in the United States).
2 Route the single connector on the PSM cable À to the
secondary wiring harness of the infotainment system, and
route the double connector on the PSM cable Á to the PSM.
3 Connect the single connector on the PSM cable to the CAN
connector on the secondary wiring harness of the
infotainment system.
4 Insert the two pin connectors into plug 2 of the PSM
connector according to the diagram and table.
Item
Wire Color
PSM Pin
Â
Ã
Brown/red
18
Brown
15
Connecting the Infotainment System to a CAN Bus
You can use the included cable to connect the infotainment
system directly to a CAN bus distributor on a compatible vehicle.
1 Locate the CAN bus distributor À in the vehicle.
The CAN bus distributor is located behind the dashboard on
the left side (the driver's side in the United States).You must
remove the panel on the left side of the dashboard (between
the dashboard and the door frame) to access it.
2 Route the harness connector on the CAN cable Á to the
secondary wiring harness of the infotainment system, and
route the other connector on the CAN cable  to the CAN
bus distributor behind the dashboard.
3 Connect the cable to the CAN connector on the secondary
wiring harness of the infotainment system.
FUSION A-Class Infotainment System Installation Instructions
4 Connect the cable to the CAN bus distributor behind the
dashboard.
5 Test the CAN functionality on the infotainment system.
6 Select an option:
• If the infotainment system does not recognize the CAN
connection, unplug the connector from the CAN bus
distributor, rotate it 180 degrees, reconnect it, and repeat
step 5.
• If the infotainment system recognizes the CAN
connection, secure the cable and continue with the
installation of the infotainment system.
Specifications
Specification
Value
Input voltage
12 Vdc
Current (max.)
12 A
Output power
26 W x 4 channels (typical)
40 W x 4 channels (max.)
Temperature range
From -10° to 70°C (from 14° to 158°F)
Radio
FM: 87.70 to 107.90 MHz
AM: 522 to 1611 kHz
Physical inputs and
connections
Input: microSD™ (front), hdmi (front), USB
(rear), AUX-in (RCA L\R, secondary harness),
AV-in (rearview camera, secondary harness),
SiriusXM (secondary harness), CAN
(secondary harness)
Output: AV-out (composite, secondary
harness), subwoofer (secondary harness)
Wireless connections
2.4 GHz Bluetooth , Wi‑Fi , and Wi‑Fi
CERTIFIED MiraCast™
®
®
Garmin , the Garmin logo, FUSION , and the Fusion logo are trademarks of Garmin Ltd.
or its subsidiaries, registered in the USA and other countries. These trademarks may not
be used without the express permission of Garmin.
®
®
Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Garmin is under license. microSD™ and the microSD logo are trademarks
of SD-3C, LLC. Sirius, XM and all related marks and logos are trademarks of Sirius XM
Radio Inc. Wi‑Fi is a registered mark of Wi-Fi Alliance Corporation. Wi‑Fi CERTIFIED
MiraCast™ is a trademark of Wi-Fi Alliance Corporation. Other trademarks and trade
names are those of their respective owners.
®
®
FUSION A-Class Infotainment System Installation Instructions
© 2016 Garmin Ltd. or its subsidiaries
www.garmin.com/support

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Print high-res
Create Date                     : 2016:03:08 16:03:15-06:00
Creator                         : AH XSL Formatter V6.2 MR5 for Windows (x64) : 6.2.7.18952 (2014/11/12 16:18JST)
Modify Date                     : 2016:03:08 16:06:27-06:00
Language                        : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Creator Tool                    : AH XSL Formatter V6.2 MR5 for Windows (x64) : 6.2.7.18952 (2014/11/12 16:18JST)
Metadata Date                   : 2016:03:08 16:06:27-06:00
Producer                        : Antenna House PDF Output Library 6.2.625 (Windows (x64))
Trapped                         : False
Format                          : application/pdf
Document ID                     : uuid:060c31bf-667a-4941-9657-acd8469b2bbd
Instance ID                     : uuid:e86a3bc8-33f6-44cd-b3b8-4d2357d44d88
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 4
EXIF Metadata provided by EXIF.tools
FCC ID Filing: IPH-02324

Navigation menu