Genbyte Technology ZBT1WF-CC3200 2.4 GHz Wi-Fi Module User Manual ZBT1WF 1501S100 WIFI
Genbyte Technology Inc. 2.4 GHz Wi-Fi Module ZBT1WF 1501S100 WIFI
Users Manual
ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. ZBT1WF-1501S100 WIFI Module Datasheet Version:V1.0 Date:Apr, 2017 Genbyte Technology Inc. Confidential Page 1 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. ZBT1WF-1501S100 WIFI Module General Description ZBT1WF-1501S100 module is a low power consumption, high performance WIFI Smart home / IoT solution, and design based on TI CC3200 SimpleLink Wi-Fi —Consists of Applications Microcontroller, Wi-Fi Network Processor, and Power-Management Subsystems in a single chip for IEEE 802.11 b/g/n compatible. It supports smartconfig technology for customer easy connected (APP). It can implement the wireless network function on the air-condition, refrigerator and other wireless devices easily. Features Support IEEE802.11 b/g/n(2.4G only), WiFi Direct(P2P), soft-AP; Embedded ARM® Cortex®-M4 Core; Support Smartconfig Technology; Consists of TCP/IP Stack; PCB sniffer ANT(or External ANT); Support UART/SPI/I2C; Small dimension: 32mm*23mm, Surface mounted; IAR/CCS Programming environment; PIN number:36 PIN; Dimension: 32.8mm*23.1mm; Application: Smart home (Refrigerator/Air-condition, etc..); Wireless IoT; Genbyte Technology Inc. Confidential Page 2 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. Specification: Table 1: Environment condition: Parameter Operation temperature Storage temperature Table 2: Electrical condition: MIN VDD -0.3 VIO -0.3 value -20℃ to 80℃ -40℃ to 120℃ TYP 3.3 3.3 MAX 3.6 3.6 Unit Vdc Vdc Mechanical Specification: Genbyte Technology Inc. Confidential Page 3 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. PIN Description: Number 10 Signal Name GND 11 GPIO6 12 GPIO1 13 GPIO2 14 15 16 EXRESET SOP2 SOP0 VDD VDD GND GND GPIO30 GPIO0 GPIO3 GPIO UART1_TXD ADC1 GPIO4 GPIO UART1_RXD ADC2 GPIO5 17 GPIO7 18 19 20 GPIO8 GPIO9 GPIO10 Genbyte Signal Description Module GND External reset PIN SOP Boot config SOP Boot config 3.3V 3.3V Module GND Module GND GPIO GPIO UART0_CTS GPIO UART0_RTS GPIO UART0_TXD GPIO UART0_RXD ADC0 GPIO ADC3 Note ADC Channel 0 Analog Input (1.5V max) ADC Channel 1 Analog Input (1.5V max) ADC Channel 2 Analog Input (1.5V max) ADC Channel 3 Analog Input (1.5V max) GPIO UART1_RTS GPIO GPIO GPIO I2C_CLK Technology Inc. Confidential Page 4 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. 21 GPIO11 22 23 24 GPIO12 GPIO13 GPIO14 25 GPIO15 26 GPIO16 27 GPIO17 28 29 30 31 32 33 34 35 36 GND VDD GPIO22 GPIO28 JTAG_TDI JTAG_TDO JTAG_TCK JTAG_TMS GND GPIO I2C_DATA GPIO GPIO GPIO SPI_CLK GPIO SPI_MISO GPIO SPI_MOSI GPIO SPI_SS Module GND 3.3V GPIO GPIO JTAG_TDI JTAG_TDO JTAG_TCK JTAG_TMS Module GND ZB-W3200 WIFI module mode configuration: SOP0 MODE UART Download Firmware Operation mode Operation mode SOP2 RF Performance For 802.11b,802.11g and 802.11n-HT20 mode,11 channels are provided. Channel Frequence(MHz) Channel Frequence(MHz) 2412 2447 2417 2452 2422 10 2457 2427 11 2462 2432 2437 2442 Genbyte Technology Inc. Confidential Page 5 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AMRBZBT1WF-CC3200" and the frequency can't be changed by end users. Genbyte Technology Inc. Confidential Page 6 of 7 ZBT1WF-1501S100 WIFI Module Genbyte Technology Inc. Important notice : Genbyte Technology Inc. reserve the right to make corrections, enhancements, improvements and other changes to its products. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products. Rev V1.0 Author Leon Genbyte Reversion History Date 2017.04.28 Technology Inc. Confidential Note First release Page 7 of 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : user Create Date : 2017:07:14 14:29:08+08:00 Modify Date : 2017:07:26 21:45:18-07:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2017:07:26 21:45:18-07:00 Creator Tool : Acrobat PDFMaker 9.0 Word 版 Document ID : uuid:6970bd0a-1081-42c6-b61c-de57705007fe Instance ID : uuid:0d36af90-ede9-4ab7-a320-86433e153a45 Subject : 4 Format : application/pdf Title : ZBT1WF-1501S100 - WIFI模块简介 Creator : user Producer : Adobe PDF Library 9.0 Source Modified : D:20170714061449 KSO Product Build Ver : 2052-9.1.0.4468 Page Layout : OneColumn Page Count : 7EXIF Metadata provided by EXIF.tools