Gibson Innovations OKAX9 wireless portable speaker User Manual revised

Download:
Mirror Download [FCC.gov]
Document ID	2868627
Application ID	Rho5XqnOEa7pjNsJL8cYlQ==
Document Description	User manual-revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.2kB (627528 bits)
Date Submitted	2016-01-11 00:00:00
Date Available	2016-01-11 00:00:00
Creation Date	2015-09-02 13:16:59
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2016-01-08 15:41:27
Document Title	User manual-revised
Document Creator	Adobe InDesign CC (Windows)

OKAX9
User manual
Contents
1 Important
Hearing safety
2 Your Bluetooth speaker
3 Get started
4 Use Bluetooth devices
5 Other features
Introduction
What's in the box
Overview of the speaker
Power supply
Switch on or go to standby mode
Connect a Bluetooth-enabled device
Play from a Bluetooth-enabled device
Control your phone call
Listen to an external device
Play through USB
Adjust volume
Listen through a headphone
6 Product information
10
10
7 Troubleshooting
General
11
11
8 Notice
12
Specifications
EN
1 Important
Warning
•
Never remove the casing of this speaker.
Never lubricate any part of this speaker.
Never place this speaker on other electrical equipment.
Keep this speaker away from direct sunlight, naked
flames or heat.
•
•
•
•
Make sure that there is enough free space
around the device for ventilation.
Use only power supplies listed in the user
manual.
Only use attachments or accessories
specified by the manufacturer.
The battery shall not be exposed to
excessive heat such as sunshine, fire or the
like.
The device shall not be exposed to
dripping or splashing.
Do not place any sources of danger on
the device (e.g. liquid filled objects, lighted
candles).
Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
•
•
•
•
•
•
Hearing safety
Caution
•
To avoid hearing damage, limit the time you use the
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter is the safe
listening time.
Be sure to observe the following guidelines
when using your headphones.
•
Listen at reasonable volumes for
reasonable periods of time.
•
Be careful not to adjust the volume as your
hearing adapts.
EN
•
•
Do not turn up the volume so high that
you can't hear what's around you.
You should use caution or temporarily
discontinue use in potentially hazardous
situations.
Excessive sound pressure from earphones
and headphones can cause hearing loss.
•
•
Note
The type plate is located on the bottom of the product.
2 Your Bluetooth
speaker
Thank you for purchasing an Onkyo product.
Please read this manual carefully before making
any connections or using this product. By
following these instructions, you’ll get the best
audio performance and the most listening
pleasure from your Onkyo product. Keep this
manual for future reference.
Introduction
With this speaker, you can
•
enjoy audio from your Bluetooth-enabled
devices, USB devices or other external
audio devices; and
•
control the incoming phone call through
Bluetooth connection.
What's in the box
Check and identify the contents of your
package:
•
Main unit
•
Power adapter
•
3.5mm audio cable
•
USB cable
Printed materials
•
EN
Overview of the speaker
a b c d
efgh
button/indicator
•
Press briefly to switch on or go to
standby mode.
•
In standby mode, press and hold to
switch off.
•
Indicate the power status.
•
Start, pause, or resume play.
Press to answer an incoming call.
During a call, press to end the current
call.
•
•
c -/+
•
Adjust volume.
button/indicator
Press and hold for 2 seconds to enter
pairing mode manually.
•
Press and hold for 7 seconds to clear
pairing information.
•
Indicate the Bluetooth connection
status.
•
e DC IN socket
•
Connect the power adapter.
•
Charge the built-in battery of the
speaker.
f AUDIO IN
socket
•
Play an external audio device through
USB.
EN
g AUX IN socket
•
Connect an external audio device.
•
Connect a headphone.
3 Get started
Note
•
Always follow the instructions in this chapter in
sequence.
Rechargeable battery has a limited number of charge
cycles. The battery life and number of charge cycles
vary by use and settings.
It takes you approximately three hours to fully charge
the battery.
•
Power supply
To charge the built-in battery:
•
Connect to AC power supply.
Either AC power or battery can be used as
power supply of this product.
System
status
On/off
Option 1: AC power
Caution
•
•
•
On
On
Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the back
or underside of the speaker.
Risk of electric shock! When you unplug the AC
adapter, always pull the plug from the socket. Never
pull the cord.
Battery status
Low power (less
than 10%)
Under charging
Fully charged
Power LED
status
Flashing red
Flashing white
Solid white
Switch on or go to standby
mode
•
Connect the power adaptor to:
•
the DC IN socket at the back of the
speaker.
•
the wall outlet.
Press to switch the speaker on.
» If the speaker is fully charged, the
power indicator turns solid white.
» If the speaker is being charged, the
power indicator flashes white.
» If the speaker is in low battery (with
less than 10% power), the power
indicator flashes red.
•
To enter standby mode, press briefly.
» The power indicator is dimmed in
white.
•
To switch off when the speaker is on or in
standby mode, press and hold for two
seconds.
» The power indicator turns off.
Option 2: Battery power
Tip
The speaker can also be powered by the builtin rechargeable battery.
•
•
In Bluetooth mode, if Bluetooth connection is invalid or
music playback is stopped for 15 minutes, this speaker
switches to standby mode automatically.
In AUX IN mode, if the audio-in cable is disconnected
or music playback is stopped for 15 minutes, this
speaker switches to standby mode automatically.
EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices and control the
incoming call through Bluetooth.
Connect a Bluetooth-enabled
device
Note
•
•
•
•
•
•
•
Make sure that your Bluetooth device is compatible
with this speaker.
Before pairing a device with this speaker, read its user
manual for Bluetooth compatibility.
The speaker can memorize up to 8 paired devices.
Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
Keep away from any other electronic device that may
cause interference.
The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
The speaker can connect up to 2 Bluetoothenabled devices at the same time.
Bluetooth
Bluetooth
ON
Devices
Onkyo
Onkyo X9
X3
Press and hold on the speaker for two
seconds.
» The Bluetooth indicator flashes blue.
On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
(refer to the user manual of the device).
When [Onkyo X9] is displayed on
your device, select it to start pairing and
connection. If necessary, enter the default
password “0000”.
» After successful pairing and connection,
the speaker beeps twice, and the
Bluetooth indicator turns solid blue.
Repeat steps 1 to 3 to add a second
Bluetooth device.
Note
•
EN
When there are two Bluetooth-enabled devices
connected to the speaker, you can repeat steps 1 to 3
to add a new device. In this case, the earliest connected
device will be replaced.
To disconnect the Bluetooth-enabled device:
•
Disable Bluetooth on your device; or
•
Move the device beyond the
communication range.
To clear the existing pairing information:
•
Press and hold for 7 seconds.
To reconnect the Bluetooth-enabled device:
•
For a paired Bluetooth device on which
automatic reconnection is enabled, this
product reconnects with it once it is
detected.
•
For a paired Bluetooth device that does
not support automatic reconnection,
reconnect it with this product manually.
Bluetooth indicator
Description
Flashing blue
Connecting or waiting for
connection
Connected
Solid blue
Control your phone call
After Bluetooth connection, you can control an
incoming call with this speaker.
Button
Function
Press to answer
an incoming call.
During a call,
press to end the
current phone
call.
•
•
Note
You can talk through the microphone of the speaker.
Music play pauses when there is an incoming call, and
resumes when your phone call ends.
Play from a Bluetoothenabled device
Note
•
•
If there is an incoming call on the connected mobile
phone, music play pauses.
After successful Bluetooth connection, play
music on a connected Bluetooth device.
» Music streams from your Bluetooth
device to the speaker.
•
Note
To play from another connected device, just use
controls on that device directly and the music streaming
from the current device will be paused.
EN
5 Other features
Play through USB
Note
•
Make sure that the USB device contains playable audio
content.
Listen to an external device
With this speaker, you can also listen to an
external audio device such as an MP3 player.
Make sure there is no music streaming
from the connected Bluetooth device (if
available).
Connect an audio input cable with a 3.5
mm connector on both ends to
•
the AUX IN socket on this speaker,
and
•
the headphone socket on the external
device.
Play music on the external device (refer to
its user manual).
» The speaker switches to the AUX IN
source.
Tip
•
When you start music streaming from a connected
Bluetooth device, the speaker switches to the Bluetooth
source automatically.
EN
Make sure there is no music streaming
from the connected Bluetooth device (if
available).
Connect a USB charging cable to
•
the AUDIO IN
socket on this
speaker, and
•
the USB socket on your mobile phone.
Play music on your mobile phone (refer to
its user manual).
» The speaker switches to the USB
source.
•
Note
When you start music streaming from a connected
Bluetooth device, the speaker switches to the Bluetooth
source automatically.
Adjust volume
Press +/- on the speaker to increase or
decrease the volume.
•
•
Listen through a headphone
Plug a headphone (not supplied) into the
socket.
EN
6 Product
information
Note
•
Product information is subject to change without prior
notice.
Specifications
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
Aux In
4 x 10W, 1% THD
40 Hz - 20 kHz, ±3dB
> 80 dBA
650mV (RMS), 22k
ohm
Bluetooth
Bluetooth version
Supported Profiles
Range
V2.1
HFP, A2DP, AVRCP
10 m (Free space)
Speakers
Speaker
Impedance
Speaker Driver
Sensitivity
4 ohm
4 x 2" mid range drivers, 2 x
3/4" high freq tweeter
> 82dB/m/W ± 3dB/m/W
General information
Power Adaptor
*)3'$
(*0(
Power Input
DC Output
100 - 240V, 50/60 Hz
15V 3A
10
EN
Built-in Battery
Dimensions - Main
Unit (W x H x D)
Weight - Main Unit
Lithium ion battery
( 11.1V,2200 mAh)
195 x 93 x 51 mm
0.6 kg
7 Troubleshooting
Warning
•
Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, contact Onkyo service center. When
you contact Onkyo, make sure that the device
is nearby and the model number and serial
number are available.
General
•
The speaker is not in pairing mode. Hold
to enter pairing mode, and then try again.
The paired device connects and disconnects
constantly.
•
The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•
For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this speaker.
The speaker is in demo mode and not
working as usual.
•
The demo mode is not intended for end
users. You may have activated this mode by
accident. In this case, press and hold for
15 seconds to exit demo mode and enter
standby mode. Then you can power on and
operate the speaker as usual.
No power
•
Make sure that the AC power plug is
connected properly.
•
Make sure that there is power at the AC
outlet.
•
Recharge the built-in battery.
No sound
•
Adjust volume on the speaker or the
Bluetooth-connected device.
•
Make sure that your Bluetooth device is
within the effective operational range.
No response from the speaker
•
Restart the speaker.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•
The Bluetooth reception is poor. Move the
device closer to this speaker or remove
any obstacle between them.
Cannot connect with the device.
•
The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
EN
11
8 Notice
Any changes or modifications made to this device that are not
expressly approved by Gibson Innovations may void the user’s
authority to operate the equipment.
Notice for the USA and Canada
This device complies with Industry Canada license-exempt RSS
standard(s) and Part 15 of the FCC Rules .
Operation is subject to the following two conditions:
1 this device may not cause harmful interference, and
2 this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules and CAN ICES-3(B)/NMB-3(B) of Industry Canada. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Relocate the receiving antenna.
•
Increase the separation between equipment and receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
RF Radiation Exposure Statement: This equipment complies
with FCC’s and IC’s RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter
must be installed and operated to provide a separation distance
of at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
Installers must ensure that 20cm separation distance will be
maintained between the device (excluding its handset) and users.
CAN ICES-3(B)/NMB-3(B).
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Disposal of your old product
Your product is designed and manufactured with high
quality materials and components, which can be recycled
and reused.
This product may contain lead and mercury. Disposal of these
materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local
authorities or visit www.recycle.philips.com.
12
EN

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2016:01:08 15:41:27+08:00
Modify Date                     : 2016:01:08 15:41:27+08:00
Creator Tool                    : Adobe InDesign CC (Windows)
Instance ID                     : uuid:a356bc5e-1c93-4209-809c-a4a3de2ea922
Original Document ID            : xmp.did:540CC0123072E011A125E833CCB2A077
Document ID                     : xmp.id:1b54ff02-3457-2447-95e0-b8e8916fc0dc
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:91545934-a70c-7143-a79c-9e7325d0dbba
Derived From Document ID        : xmp.did:366CACE6AEC2E011A265BE935C16BD6C
Derived From Original Document ID: xmp.did:540CC0123072E011A125E833CCB2A077
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Windows)
History Changed                 : /
History When                    : 2015:09:02 13:16:59+08:00
Phsprop 2                       : 1000 series
Date Created                    : 2007:03:01
City                            : Groningen
Create Date                     : 2005:12:01 12:32:37Z
Ww numpages                     : 16
Ww pagecnt Cover Outside        : 1
Ww pagecnt Cover Inside         : 1
Ww pagecnt Content              : 12
Ww pagecnt Back Inside          : 1
Ww pagecnt Back Outside         : 1
Ww pagecnt lang                 : EN:12;
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 13
Creator                         : Adobe InDesign CC (Windows)

EXIF Metadata provided by EXIF.tools