Gilbarco MRIR11 Point of Sale Mat Reader System User Manual

Gilbarco Inc. Point of Sale Mat Reader System

Manual

MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001 Page 1Preliminary05/24/01IntroductionPurpose of this ManualThis manual provides instruction for installing TIRIS™ Mat Reader Assembly Kit C00016-XXX.The TIRIS™ option allows customers to automatically authorize non-cash sales using a hand-held transponder tag.Important NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been investigated by Underwriters’ Laboratories, Inc. (UL®).Required ReadingBefore installing the equipment, the installer must read, understand, and follow:•this manual•NFPA 70, The National Electric Code•applicable federal, state and local codes and regulationsFailure to do so may adversely effect the safe use and operation of the equipment.MDE-4017TIRIS™ Transmitter/Receiver Mat ReaderAssembly Kit C00016-XXX InstallationMay 2001
Page 2 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Related DocumentsInstaller must obtain, read and understand all site preparation documentation provided by the point of sale company authorizing the installation before attempting to install this equipment.In addition, the installer must be familiar with the information in the following documents.Required ToolsThe following equipment is needed to install all TIRIS™ mat reader kits:•drill motor and bits•needle nose pliers•screwdriver, Phillips® head•Zircon® stud/bracket finderParts Lists C00016-006 Kits contain the following parts:The following components are also required.Document Number Title GOLD LibraryMDE-3110 PC-Based G-SITE System Installation Manual G-SITEMDE-3111 PC-Based G-SITE System Start-Up and Service Manual • G-SITE• Service ManualMDE-3620 Gilbarco POS Console Site Preparation Manual Site PrepDescription Part Number Quantitybox, interface assembly M01814A001 1tape, neoprene foam M01870B001 2channel, plastic filler M01871B001 1cable, mat reader drive M01872A001 1tape, acrylic foam K85492-72 1power supply M01878B001 1jack, jump, push-to-start Q11011-01 1cable, data, CAT-5 Q13482-06 1clamp, cable, stick on, small Q13459-01 3document, installation (this document) MDE-4017 1diagram, block and/or interconnect M01873 0Description Part Number Quantitygraphics MR01002G003 1reader, mat, TIRIS deviceNote: The Mat Reader is delivered with the graphics in place.M01787B001 1
Page 3 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Important Safety InformationThis section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found. Electrical shock could occur and cause death or serious injury if these safe service procedures are not followed.Preliminary PrecautionsRead, understand and follow this manual and any other labels or related materials supplied with this equipment.Follow the RegulationsThere is applicable information in: NFPA 70: National Electrical Code (NEC); OSHA regulations; and federal, state, and local codes which must be followed. Failure to install, maintain or service this equipment in accordance with these codes, regulations and standards may lead to legal citations with penalties or affect the safe use and operation of the equipment.
Page 4 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Safety Symbols and Warning WordsAlert Symbol This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazards. Obey safety directives that follow this symbol to avoid possible injury or death.Signal WordsThese signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards. The precautions that follow must be followed to prevent death, injury or damage to the equipment.Proper Grounding is RequiredProper grounding is required for safe operation. See installation manual and applicable NEC, NFPA and local electrical codes for requirements.Avoid Pinched WiresPinched or cut wires (cables) may damage components. Exposed wires could create sparks and electrical shorts when applying power.Other Useful Safety InformationReplacement PartsUse only genuine Marconi replacement parts. Using parts other than genuine Marconi replacement parts could create a safety hazard, violate national, state and local regulations or void warranty.This signal word designates a hazard or unsafe practice which may result in minor injury.This signal word is used to alert you to a hazard or unsafe practice which will result in death or serious injury.This alerts you to a hazard or unsafe practice that could result in death or serious injury.CAUTIONWhen used by itself, CAUTION designates a hazard or unsafe practice which may result in property or equipment damage.CAUTIONDANGERWARNING
Page 5 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Installation Note: All installation work is to be accomplished between the hours specified by the point of sale company authorizing the installation.Install Mat Reader assembly according to the following:1Collect and arrange all tools and equipment.2If necessary for installation of kit in area specified by point of sale company, remove advertisement panels, saving all mounting hardware for re-use later.Note: Make note of non-reusable fasteners, ensuring adequate replacements are available for later use.Setting Baud Rate1Remove Mat Reader Interface Box cover to access logic board.Figure: Mat Reader Interface Box Cover2Locate jump jacks on logic board for Mat Reader.Figure: Jump Jacks for Baud Rate Settingcover screwBAUD1 2 4
Page 6 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/013Set the jump jacks as follows (see “Figure: Jump Jacks for Baud Rate Setting” on page 5).4If not daisychaining Mat Reader Interface Boxes, reinstall cover.Note: Daisychaining is connecting the output from one Interface Box to the input of another.Addressing Logic Board - Only for DaisychainingAddress for Mat Reader must match address on previously installed Mat Reader. Follow these steps:1Access logic board for Mat Reader being installed.2Locate jump jacks on previously installed Mat Reader logic board M01803A001.Figure: Jump Jacks for Address SettingMat Reader Baud RatesBaud Rate (Note) BAUD 1 BAUD 2 BAUD 44800 OUT OUT OUT2400 IN OUT OUT1200 OUT IN OUT300 IN IN OUT38400 OUT OUT IN19200 IN OUT IN9600 OUT IN IN4800 IN IN INNote: 4800 is the default value and the Mat Reader value.Electrostatic Discharge DamageWorking on electronics without connecting to a ground or dischargingstatic can damage electronic parts. Use a wrist strap. CAUTION ADDR1 2 4 8 16
Page 7 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/013Note position of jump jacks on previously installed Mat Reader logic board, and set jump jacks on board for Mat Reader being installed to match address on logic board.4Reinstall cover.Mat Reader AddressesAddress on Logic Board M01803A001 ADDR 1 ADDR 2 ADDR 4 ADDR 8 ADDR 160 OUT OUT OUT OUT OUT1 IN OUT OUT OUT OUT2 OUT IN OUT OUT OUT3 IN IN OUT OUT OUT4 OUT OUT IN OUT OUT5 IN OUT IN OUT OUT6 OUT IN IN OUT OUT7 INININOUTOUT8 OUT OUT OUT IN OUT9 IN OUT OUT IN OUT10 OUT IN OUT IN OUT11 IN IN OUT IN OUT12 OUT OUT IN IN OUT13 IN OUT IN IN OUT14 OUTINININOUT15 IN IN IN IN OUT16 OUT OUT OUT OUT IN17 IN OUT OUT OUT IN18 OUT IN OUT OUT IN19 IN IN OUT OUT IN20 OUT OUT IN OUT IN21 IN OUT IN OUT IN22 OUTININOUTIN23 IN IN IN OUT IN24 OUT OUT OUT IN IN25 IN OUT OUT IN IN26 OUT IN OUT IN IN27 IN IN OUT IN IN28 OUT OUT IN IN IN29 IN OUT IN IN IN30 OUTININININ31 IN IN IN IN INElectrostatic Discharge DamageWorking on electronics without connecting to a ground or dischargingstatic can damage electronic parts. Use a wrist strap. CAUTION
Page 8 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Mounting Mat Reader Interface Box1Determine the location for the installation of indoor equipment.Note: Refer to site prep document provided by point of sale company and keep in mind overall length of cable to connect Mat Reader Interface Box to Mat Reader.2Use a Zircon stud/bracket finder to ensure no electrical conduits or pipes are located inside of wall where the Mat Reader Interface Box is to be mounted. Also, ensure the Mat Reader Interface Box is to be located where studs or wall (concrete/brick/drywall) mollys can be used for mounting.3Mark and drill holes. Insert wall mollys as required.4Use appropriate mounting hardware to secure the Mat Reader Interface Box to the wall.Figure: Mat Reader Interface Box Mounting HolesDo not use the Mat Reader Interface Box as a drill guide. It may be used as a template to mark the holes to be drilled.CAUTIONmounting holes
Page 9 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Connecting Data Cables to Mat Reader Interface BoxRun both power and data cables to port end of Mat Reader Interface Box (see “Figure: Mat Reader Interface Box Mounting Holes” on page 8) as follows.1Connect the P3 end of the ribbon cable (M01872A001) to the RFID interface port (P3) .2Connect the J1end of the CAT-5 cable (Q13482-06) to the J1IN port.Figure: Connecting to Mat Reader Interface BoxConnect power supply here. Connect J1 end of CAT-5 cable here.If daisychaining, connect CAT-5 from J1IN on other interface box here.Connect P3 end of ribbon cable here.
Page 10 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Connecting Data Cables from the Mat Reader Interface Box1Position Mat Reader face down.Figure: Bottom Side of Mat Reader2Select side for ribbon cable (M01872A001) connection based on counter top configuration requirements.3Install strip of acrylic foam tape (K85492-72) in base of channel on side selected for ribbon cable.4Peel second release liner, exposing adhesive.5Carefully connect the P1/P2 end of the ribbon cable (M01872A001) to the back side of the Mat Reader.Note: The cable can be plugged in from either side. Since the cable is not keyed, the orientation does not matter. Be sure the cable will be flat and not twisted once the Mat Reader is face up.bottom side of Mat Reader7-pin connectorchannel for ribbon cable (acrylic foam tape in place)bottom side of neoprene foam tape (flipped over to show connector)
Page 11 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Figure: Connecting to Mat Reader6Install neoprene foam tape (M01870B001) over ribbon cable and sides of channel. Foam tape should fit snugly into cutout of surrounding foam tape backer.7On unused cable channel, install plastic filler channel (M01871B001).8Install remaining neoprene foam tape (M01870B001) over filler channel. Foam tape should fit snugly into cutout of surrounding foam tape backer.9Gently turn the Mat Reader to the face-up position.Figure: Mat Reader - Face Up10 Connect the loose end of the CAT-5 cable to the RS-232-1 or RS-232-2 port on the back of the G-SITE system.Note: The exact G-SITE system port depends on the G-SITE system configuration.ribbon cable connected to 7-pin connectorunused channel filled with plastic filler channel and covered by neoprene foam tapebottom side of neoprene foam tape
Page 12 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Connecting Power SupplyConnect the power supply (M01878B001) provided with kit as shown.1Plug the wall-mounted transformer into the AC power outlet.Note: This AC power outlet must be on the same circuit as the G-SITE system.2Connect the plug end of the power supply cable to the JDC1 port on the Mat Reader Interface Box (see “Figure: Connecting to Mat Reader Interface Box” on page 9).Figure: Power Supply (M01878B001)wall-mounted transformerplugs into JDC1 portplugs into AC power outlet
Page 13 MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001Preliminary05/24/01Completing InstallationFigure: Mat Reader Connections1Dress all cables and secure with stick on cable clamps (Q13459-01).2Clean up the work area.3Go to “Commissioning and Warranty Information” on page 14.CAT-5 cable connects herepower supplyinterface boxMat Readerribbon cable
© 2001 Marconi Commerce Systems Inc. 7300 West Friendly Avenue • Post Office Box 22087Greensboro, North Carolina 27420 Phone (336) 547-5000 • http://www.marconicommerce.com • Printed in the U.S.A.MDE-4017 TIRIS™ Transmitter/Receiver Mat Reader Assembly Kit C00016-XXX Installation • May 2001 Preliminary05/24/01Commissioning and Warranty InformationUpon completion and testing the Mat Reader system, the installing contractor must call the Marconi Commerce Systems Call Center @ 1-888-800-7498 to register the installation and activate the warranty. Note the installed unit’s full Model Number (C00016-XXX) and serial number before making this call.•All Mat Readers have a one-year parts only warranty.Note: Parts are to be returned through and obtained from the local Marconi distributor.•Labor warranty, if any, is unit and customer specific.Marconi Commerse Systems strongly recommends using only Marconi trained ASCs (Authorized Service Contractors) to perform service on the units. Use of non-authorized service personnel to repair or service these units may void warranty. Call your local distributor for service.TRIND® is a registered trademark of Marconi Commerce Systems Inc.Phillips® is a registered trademark of Phillips Screw Company.UL® is a registered trademark of Underwriters’ Laboratories, Inc.Zircon® is a registered trademark of Zircon International Inc.

Navigation menu