Golden Mark WD100 Wireless dimmer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2339993
Application ID	MFdY2FePRLuDOp2z+AkLpw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.63kB (457884 bits)
Date Submitted	2014-07-30 00:00:00
Date Available	2014-07-30 00:00:00
Creation Date	2014-07-15 15:38:08
Producing Software	OpenOffice 4.1.0
Document Lastmod	0000-00-00 00:00:00
Document Title	User manual
Document Creator	Writer

This product speaks with other Z-Wave certified devices
Wireless Dimmer Module
WD-100
In Wall Dimmer
INTRODUCTION
domitech™ WD-100 is a member of the Z-Wave® family and communicates with other ZWave certified devices in a control network. WD-100 replaces a standard in-wall light switch
and turns it into a Z-Wave controlled network device with dimming and On/Off light control.
Each Z-Wave device serves as a node to repeat the signal in the network, thus, extending the
overall Z-Wave mesh wireless network range. Different types and brands of Z-Wave devices
can be associated with Domitech WD-100 in your system and they will work together to
optimize and expand the coverage of your Z-Wave network. Once setup is completed, you
can enjoy the convenience and leisure which WD-100 offers.
FEATURES










Works with incandescent and dimmable florescent (CFL), or LED lighting
7 LED indicators for ON/OFF/Dimming level status
Can be controlled wirelessly or manually
Fits into standard single or multiple gang junction box and standard wall plates
GROUP/SCENE/ALL enabled
Decorative keypad can be replaced manually to match color with other wall switches
Over-The-Air firmware upgrade available with compatible gateway, Z-Wave static
controller, PC and software
Z-Wave 500 Series module inside
Internal resettable fuse to protect from surge current
Manual reset capability
! WARNING !
RISK OF FIRE, ELECTRICAL SHOCK & BURNS
DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENT
No user serviceable parts are in this module
The lighting connected to the WD-100 must not exceed 600W incandescent, 150W dimmable
CFL/LED.
CAUTION: To Reduce the Risk of Overheating And Possible Damage To Other Equipment,
Do Not Install To Control A Receptacle, A Motor-Operated Appliance, A Non-Dimmable
Fluorescent Lighting Fixture, Or A Transformer-Supplied Appliance
The color of the keypad switch is changeable by the following method,
1. Lift the air gap switch up to avoid
electrical shock
2. Push side tabs in
and lift the cover
plate up to release
3. Align the tabs of
the replacement cover
plate and push to snap
in
4. Push the air gap switch back
down
SETUP
Step 1. Identifying the wiring terminals on the module
Step 2. ! WARNING ! RISK OF SHOCK ! Make sure power is OFF before wiring !
Step 3. Remove the wall plate and the existing switch(if mounted) at your preferred
installation location. You may label the wires connected to the screw terminals before
disconnecting the switch. Please check that the wiring configuration below is present in the
wall switch box, otherwise consult a qualified electrician.
4 wires for 2-way circuit
5 wires for 3-way circuit
1. Line(Hot) - Black
2. Neutral - White
3. Ground – Green or Bare
4. Traveler (3-way) Red or Other
5. Load - Black
Wiring Information
Use copper wires only
UL specification: the tightening torque for the screws is 14 Kgf-cm (12 lbf-in)
Strip insulation 5/8" (16mm)
Wire connection can be made either to
14 AWG or larger rated at least 80°C
14 AWG rated at least 80°C
2-way circuit
Making connections
The Traveler terminal is not used in a 2-way circuit. Do not remove the insulation tape on the
Traveler terminal in this application
3-way circuit
Making connections
Please refer to WA-100 user manual for wiring instructions of the associating switch. The
maximum length of Traveler wire may not exceed 250ft.
Gang Box
To install the WD-100 in a gang or J box, the
tabs on the sides of the metal yoke may need
to be removed. For single gang switch, no
changes should be required. For dual or
higher gang configuration where switches are
next to each other, the tabs need to be
removed. Simply take a pair of pliers, grab
the tabs and wiggle until the tabs break off.
This will lower the electrical rating of the
module. Please refer to the following details
1x gang box
rating: 600W incandescent
150W dimmable CFL/LED
with 2 side tabs
2x gang box
rating: 500W incandescent
125W dimmable CFL/LED
with 1 side tabs
3x gang box
rating: 400W incandescent
100W dimmable CFL/LED
with no side tabs
Step 4. When proper wiring is completed, secure the module to the wall box. Restore power
to the circuit to test if the connected lighting can be turned ON/OFF/Dim manually by the
rocker on the module before remounting the wall plate. Also observe the status change of the
LED indicators to ensure the module is in normal operating mode. If WA-100 Auxiliary
Switch is used for a 3-way connection, please also test if it can control the lighting.
Step 5. Add(Include) the module into your network by a Z-Wave certified controller. Please
refer to the controller’s instructions manual for details.
Manual Reset
Note: If Inclusion still fails after the 2nd attempt, you need to first reset the module before
repeating the above steps. The manual reset method is as follows,
1. Turn the connected lighting ON with the rocker
2. Quickly tap the top
side(ON) of the rocker 3
times
Then, quickly tap the bottom
side(OFF) of the rocker 3
times
If you see the lighting turns OFF, it means that the module has been reset successfully and
you may retry Step. 5 above to add the module into your network. Otherwise, please repeat
the manual reset procedures.
Note: if the module is previously Added(Included) in your network, resetting it locally does
not mean it has been removed from your network. You may still need to Delete(Exclude) the
module from the network by your controller if desired.
BASIC OPERATION
The connected lighting can be controlled manually with a rocker
OR
Wirelessly with a remote controller
A Z-Wave certified controller of either portable or static is capable of setting up Domitech
products in your desired network. Once the module is added, you may assign it to a Group or
Scene, change its reaction when the All command ON or OFF is received. Furthermore, it can
be set in Association with another Z-Wave device to perform a specific function. Please refer
to the instructions manual of your remote controller for details and procedures on how these
settings can be done.
Please note that the module will be OFF after a power failure
About the rocker switch:
There is only 1 rocker switch on this module for manual operation that allows you to
1. Turn the connected lighting ON/OFF and DIM by tapping the switch. Tapping and
releasing the upper part of the rocker turns the lighting ON. Tapping and releasing the
lower part of the rocker turns the lighting OFF. Press and hold the upper part of the
rocker to Dims Up the lighting. Press and hold the lower part of the rocker to Dim
Down the lighting. Simply release the rocker when the desired brightness level is
reached during dimming.
2. Add(Include) or Delete(Exclude) the module to/from your Z-Wave network with your
primary controller. Please refer to the instructions manual of your gateway or remote
controller for details and procedures on how these actions can be done. Normally, the
sequence is as follows: when the inclusion (or exclusion) process is prompted by your
primary controller, single click and release the rocker switch => the controller should
show that the action was successful => if the controller shows it was a fail, repeat the
procedure.
Note: the orientation of the ON/OFF on the rocker switch can be inverted by changing the
following configuration with a controller(if supported)
Parameter 4
Length: 1 byte
Valid values: 0 or 1 (default 0)
About the 7 LED indicators:
There are in-line 7 LED indicators on this module to display the connected lighting status.
All 7 LED indicators are ON when the
connected lighting is at full brightness
(100%)
All 7 LED indicators are OFF when the
connected lighting is shut off
(0%)
Only the bottom 4 LED indicators are ON
when the connected lighting is at around half
of it's full brightness
(50-60%)
Note: there are some occasions when the lighting is dimmed down to the minimum brightness
level(only the bottom LED is ON) but it appears OFF visually. Depending on the lighting
devices used, the behaviors vary. You may check the actual lighting status with the indication
of the bottom LED
About dimming:
The time interval of brightness change between dimming up and down can be adjusted by
changing the following configuration with a controller(if supported)
Parameter 9 (level)
Length: 1 Byte
Valid Values: 1-99 (default = 1),
indicates the number of levels the lighting will change when the timer runs out.
Parameter 10 (timer)
Length: 1 Byte
Valid Values: 1-255 (default = 3),
indicates the time duration of each level.
The resolution is 10 milliseconds. For example, a default value of 3 means the timer runs out
every 30 milliseconds. Using the combinations of these 2 parameters, you can create a dim
rate adjustment range as short as 10 milliseconds to a very slow dim rate.
About the Z-Wave 500 Series module:
You can use a Z-Wave certified portable or static controller to communicate with the module.
Depending on the capability of your controller or gateway software, the following simple to
advanced operations can be performed. Please refer to the controller's or gateway manual for
details.
1. Turn the connected lighting On/Off and Dim
2. Add(Include) or Delete(Exclude) your WD-100 to/from your network
3. Assign your WD-100 to a specific Group/Scene and/or to include your WD-100 as
part of your All ON or OFF command
4. Over-the-Air firmware update by your gateway or static controller
5. Lifeline function which automatically notifies the associated modules and the network
that a manually reset device is no longer in the network, thus, the corresponding
association becomes invalid
SPECIFICATIONS
Model: WD-100
Input power: 120 VAC, 60 Hz.
Max output loading: 1x gang box 600W incandescent, 150W dimmable CFL/LED
2x gang box 500W incandescent, 125W dimmable CFL/LED
3x gang box 400W incandescent, 100W dimmable CFL/LED
Radio frequency: 908.4 MHz/916 MHz.
Wireless range: up to 130ft line of sight between the controller and the other available nodes.
Normal operating temperature: 77°F (25°C)
For indoor use only.
Interoperability with Z-Wave devices
A Z-Wave network can integrate devices from various classes of products, and these devices
can be made by different manufacturers. The domitech product introduced in this instructions
manual has a Z-Wave certification which guarantees such an interoperability.
FCC ID: 2ABWCWD100
The Federal Communication Commission Radio Frequency Interference Statement includes
the following paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment uses,
generates and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction, may cause harmful interference to radio communication. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
 Reorient or relocate the receiving antenna
 Increase the separation between the equipment and receiver
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
 Consult the dealer or an experienced radio/TV technician for help
Operation is subject to the following two conditions:
 This device may not cause interference
 This device must accept any interference, including interference that may cause
undesired operation of the device.
Important Note: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user’s authority to operate the
device.
Caution: Exposure to Radio Frequency Radiation. To comply with FCC/IC RF exposure
compliance requirements, a separation distance of at least 20 cm must be maintained between
the antenna of this device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
IC: 11786A-WD100
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Z-Wave is a registered trademark of Sigma Design
WARRANTY
domitech warrants to the original purchaser of this product that for the warranty period, this
product will be free from material defects in materials and workmanship. The foregoing
warranty is subject to the proper installation, operation and maintenance of the product in
accordance with installation instructions and the operating manual supplied to customer.
Warranty claims must be made by customer in writing within 30 days of the manifestation of
a problem. domitech's sole obligation under the foregoing warranty is to repair, replace or
correct any such defect that was present at the time of delivery, or to remove the product and
to refund the purchase price to customer. The warranty does not extend to consequential or
incidental damage to other products that may be used with this product. For inquiry and
customer service, email to support@dragontechind.com
All brand names shown are trademarks of their respective owners
Warranty period: limited 1 year from date of purchase
domitech Products
2140 E. Southlake Blvd., Suite L-312
Southlake, TX 76092
WS100_07022014_En_v1.1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 13
Language                        : zh-CN
Creator                         : Writer
Producer                        : OpenOffice 4.1.0
Create Date                     : 2014:07:15 15:38:08+08:00

EXIF Metadata provided by EXIF.tools