Gospell Smarthome Electronic GD7067 Digital Wireless Camera System User Manual GT4067 GD7067 QSG
Shenzhen Gospell Smarthome Electronic Co., Ltd. Digital Wireless Camera System GT4067 GD7067 QSG
User Manual
60g
66 X 35 X 12mm
DC 12~24V
50M (MAX.)
2400~2483.5MHz
4.4 (20dB BW)
QPSK
+18dBm @ QPSK
EVM 8%
-72dB
O O O O
-10 C~+50 C/14 F~122 F
15%~85%RH
60g
66 X 35 X 12mm
DC 12V@250mA; DC24V@150mA
DC 12~24V
50M (MAX.)
2400~2483.5MHz
4.4 (20dB BW)
QPSK
+18dBm@QPSK
EVM 8%
-72dB
IP66
65mA±10
1Vp-p±0.2@75Ω
<0.5 Lux
O O
80 (NTSC), 82 (PAL)
DC12V±0.5V
1Vp-p±0.2
1/4" CMOS
656 X 488
NTSC/PAL
Model: 8902JN
8902JN = GL8902(Camera)+GT4067(Transmitter)+GD7067(Receiver)
WGL8902ired camera: X 1
Wireless receiver )(GD7067
Wireless transmitter )(GT4067
Wired camera(GL8902)
Wireless Transmitter
(GT4067)
Wired camera
(GL8902)
Wireless Receiver
)(GD7067
Display or Monitor
Black line
Red line
Power input
(Connected with a
cigarette lighter)
Indicator
Antenna
Connect the vehicle
power supply
Bracket
Camera Lens
Prompt:
Transmitter
Receiver
Quick Start Guide
Camera
Camera
TransmitterReceiver
Unobstructed Effective Range
Unobstructed Effective Range
Power Supply
Weight
Receiving Sensitivity
Weight
Dimensions (W X D X H)
Receiving Sensitivity
Power Supply
Video output
Dimensions (W X D X H)
Operation Humidity
Operation Temperature
Transmission Power
Transmission Power
Modulation/Demodulation Mode
Modulation/Demodulation Mode
Image Sensor
Effective Pixels
Video Format
Minimum illumination
View Angle
Consumption Current
Video output
Power Supply
Waterproof Capacity
Consumption Current
Transmission Frequency
Transmission Frequency
Data Bandwidth
Data Bandwidth
Packing List: Specifications:
Product Structure: Installation Wired Camera:
Video Output
Video Input
Pairing
Video Output
Indicator
Antenna
Pairing
1. In the proper position of rear license plate
drill a screw hole for mounting screw.
2. Use a screwdriver to the first screw is screwed
into the screw hole of the drilled.
3. Move the camera orientation to adjust
the display effect.
4. After adjustment, second screw drill, mount and
tighten the screws, the camera is installed.
Wiring diagram and the pairing setting:
Wired camera+Wireless transmitter:
Rear
lamp
Wireless receiver:
Cigarette lighter
power supply
Video input
Wireless Receiver
Wireless Transmitter
1, this product is suitable for 12V power car;
2, please find auto electrician to install this product;
4, broken wiring must be insulated.
3, the wire harness to avoid high temperature and
high pressure location;
Wireless receiver: GD7067 X 1
Pairing: To pair the TX box and RX box successfully. please follow the instructions below accordingly.
1. Press and hold the pairing button on the TX box for 3sec. The indicator light will start flashing.
2. Within 30sec of flashing time. Press and hold the pairing button on the RX box for 3sec until the indicator light flashes.
3. Once both TX box and RX box are successfully paired. the indicator lights on TX box and RX box will stop flashing.
Pair button Pair button
Wireless transmitter: X 1GT4067
Digital Wireless Camera System
FCC Warning Statements:
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
“RF Exposure Guidance: This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be operated with a minimum distance of
20cm between the radiator and persons. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter, except in accordance with FCC
multi-transmitter product procedures.”