Gospell Smarthome Electronic GT4065 2.4G Wireless Rearview Camera and Receiver User Manual 8907AZ OEM XIAO

Shenzhen Gospell Smarthome Electronic Co., Ltd. 2.4G Wireless Rearview Camera and Receiver 8907AZ OEM XIAO

User manual

2.4GHz WirelessCameraModel: 890Car Rearviewand Receiver2BG 8902MJ
CONTENTS1. Foreword2. Packing List3. Structure4. Installation6. FCC Information5. Specifications112311Back Cover* 89 means 890 + G 406 +02BG 2 T 5 T 0138902MJ means GL8902 GT4065 Gb6904GL G 4*++-1-
1. FOREWORDCONGRATULATIONS. The Wireless Camera, when used asdescribed, wcar rearviewill give you years of dependable service in your car, truck,RV, or mini-van. We have taken numerous measures in quality control toensure that your product arrives in top condition, and will perform to yoursatisfaction.2. PACKING LISTCar Rearview CameraReceiver G 40132.4GHz Wireless TWireless Transmission Box Gt40652.4GHz wireless Receiver GB6904conversion cord-2-
-3-3. STRUCTUREConnector Wireto Gt4065Gl89023-1 CameraCar RearviewWireless Transmission BoxPower WireGt4065Connector toGl8902
-4-4. INSTALLATIONThese installation instructions do not apply to all vehicles. They aremeant as only as a general guide due to common vehicle makes &models. For specific questions, contact your vehicle's manufacturer.Consult your local motor vehicle laws on the use of this product.4-1 CAMERA INSTALLATIONYou may mount the camera near the license plate's top with screws.1. Uplift the backside door ofvehicle and the cover toinstall profitably. (Fig1)remove2. Drill three holes. The one hole forthe c ire and two holes forcamera. (Fig2)onnector winstallation of the (Fig1)
-5-(Fig2)Note:* Some vehicle's may have a holeavailable to pass the wire through, if not,you need to drill a hole close to the locationof camera for the connector wire, and twoholes for the screws of camera installation.* Before you drill those holes, you mustcheck out and make sure no othercomponents too close to your aiguille.Before drilling, we strongly commend youremove electrical parts or fuel systembehind the vehicle door and clear thesurroundings to avoid unexpected damages.3. If the holes are all ready, pass theof camera into the vehicle.(Fig3)Install the camera by two screws suppliedand adjust the camera to an proper angle.(Fig 4)connectorwire(Fig3)(Fig 4)(Fig 5)4. Then connect the camera to thetransmission box GT406 .(Fig5)55. Fix the transmission box Gt406on the surface by the sheet screws wesupplied. (Fig6)5Note:* Generally we advise you put it on thecenter of the license plate top.6. Next you'll need to find the vehicle's reverse lights. Turn off thevehicle's reverse lights. Turn the vehicle's ignition key to the accessoryposition, engage the parking brake and put the car in reverse. Look atthe vehicle's tail lights to see where the reverse lights are located, theyare the white lights.
(Fig7)To locate the reverse light's 12/24VDC wireit will be necessary to gain access to the rearof the vehicle's tail light.For help locating the vehicle's reverse lightcircuit contact your vehicle's manufacturerfor vehicle specific wiring diagrams.7.Once you have located the reverse lightcircuit you will have to route the GT4062Power Wire to that location. You mustsecurely fasten the Power Wire to preventit from being caught on any vehiclecomponent such as the trunkhinge (Fig. 7). Never route the cableoutside the vehicle.8.The reverse light sockets on most vehicles have two wires connectedto them. Usually the negative wire is black and the positive wire is acolored wire. If you are uncertain about the wiring, you can use a 12/24volt test light available at most auto parts stores to determine which isthe positive wire.Camera'sPower CableCamera'sPower Cablea.Remove the reverse light socket from its housing, then remove the blubfrom the socket.b.Engage the parking brake, turn the ignition key to the ON position, butdo not start the vehicle. Put the gear shift in the reverse position.c.Attach the ground wire of the test light to the vehicle ground, thentouch one of the socket's contacts with the positive lead.-6-d. If the test light lights up, then the wire corresponding to that contactis the positive wire. If it doesn't light up the opposite wire is thepositive wire.9. After determining which wire is the positive and which is the negative,turn off the ignition key, then remove the battery's negative cable.Follow the manufacturer's instructions for the safe use of the test light.(Fig6)
-7-12. Replace the reverse light bulb, then reinstall the light socket. Secureall the wire with cable ties or electrical tape. Reattach the negativebattery cable to the battery.11. Next splice the black wire of the transmission box GT4062 powerwire to the reverse light's negative(-) wire or ground.Wiring Connector DiagramG 406 is equipped with Reverse Voltage Protection. If the cameradoes not operate, please check that the Red wire is connected to positive(+) and the Black wire is connected to negative(-).t510. Following the In-Line Wire Connector Instructions section, splice theRed wire using the supplied In-Line Wire Connector to the reverse light'spositive(+) wire. Use a set of slip joint pliers to squeeze the TAP andinsure good connection.
You do not need to use the In-Line Wire Connectors. canwired directly to the reverse light circuit by stripping the reverse lightwires then twisting GT4062 wires to the exposed reverse light wires.Once connected, wrap with electrical tape. Do not attempt this if youare not knowledgeable with electrical installation practices.GT4062 be-8-In-Line Wire Connector InstructionsInsert the existingwire to be tapped. Insert the wire tobe attached.Crimp tap thenclose lock4-2:12/24 Volt Cigarette Lighter AdapterUsingage and2 4GHz wireless Receiver Gt4013.1. Plug the end of the power cable into the.electric equipment3. Plug the 12/24 V car power adapter intocar power socket.4. The monitor or GPS will be automatically activated when you back up the car.The monitor will be automatically shut when t goes forward.he car2.Plug the end of the AV cable into the AVequipment4-3 2.4GHz wireless Receiver Gb6904 using1 Clamp the Gb6904 on a GPS. equipment2 the GPS equipment will supply 5V voltage to the Receiver andthe Receiver can supply AV signal to GPS..3 The monitor of GPS. will be automatically activated when youclamp the Receiver
--9(Max.)150mA--ModulationInput voltageOutput currentFM12V 24V DC/15A.Output Voltage5VReceived Sensitivity≤-85dBm510 96 628 84 (NTSC) 5 6(PAL)ISM 2,400-2,483MHzISM 2,400-2,483MHzMinimum IlluminationIR Night RangeHorizontal View Angle80 degreeGL8902+GT4065<0. Lux54m+12 DCV2mW/FCC,10wm/CEConsumption Current (Max.)15A.5. SPECIFICATIONSRECEIVERGT4013ModulationInput voltageOutput currentFM5V DC110mAVideo output level1 1Vpp.Received Sensitivity≤- dBm93ISM 2,400-2,483MHzVideo output impedance75ΩRECEIVERGB4096
FCC INFORMATIONThis device complies with part15 of the FCC Rules. Operation is subjectto the following two conditions:(1) this device may not cause harmful interference,(2) this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate theequipment.--10
GOSPELL Smarthome Electronic CO.,LTD.4-5Floor/Block 2, Vision (SZ) Park, Hi-Tech Industrial Park, Shenzhen, P.R.China

Navigation menu