Gospell Smarthome Electronic GT4065 2.4G Wireless Rearview Camera and Receiver User Manual 8907AZ OEM XIAO

Download:
Mirror Download [FCC.gov]
Document ID	1084420
Application ID	4bV4m39Nuke5aJHxejnSWw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.85kB (523120 bits)
Date Submitted	2009-03-24 00:00:00
Date Available	2009-03-25 00:00:00
Creation Date	2009-01-07 09:24:33
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2009-01-07 09:24:33
Document Title	8907AZ-OEM XIAO.cdr
Document Creator	PScript5.dll Version 5.2
Document Author:	qibt

2.4GHz Wireless
Car Rearview Camera
and Receiver
Model: 8902BG 8902MJ
CONTENTS
1. Foreword
2. Packing List
3. Structure
4. Installation
5. Specifications
11
6. FCC Information
Back Cover
* 8902BG means GL8902 + GT4065 + GT4013
* 8902MJ means GL8902 + GT4065 + Gb6904
-1-
1. FOREWORD
CONGRATULATIONS. The Wireless car rearview Camera, when used as
described, will give you years of dependable service in your car, truck,
RV, or mini-van. We have taken numerous measures in quality control to
ensure that your product arrives in top condition, and will perform to your
satisfaction.
2. PACKING LIST
Car Rearview Camera
2.4GHz Wireless Receiver GT4013
Wireless Transmission Box Gt4065
2.4GHz wireless Receiver GB6904
conversion cord
-2-
3. STRUCTURE
3-1 Car Rearview Camera
Gl8902
Connector Wire
to Gt4065
Gt4065
Wireless Transmission Box
Power Wire
Connector to
Gl8902
-3-
4. INSTALLATION
These installation instructions do not apply to all vehicles. They are
meant as only as a general guide due to common vehicle makes &
models. For specific questions, contact your vehicle's manufacturer.
Consult your local motor vehicle laws on the use of this product.
4-1 CAMERA INSTALLATION
You may mount the camera near the license plate's top with screws.
1. Uplift the backside door of
vehicle and remove the cover to
install profitably. (Fig1)
2. Drill three holes. The one hole for
the connector wire and two holes for
installation of the camera. (Fig2)
-4-
(Fig1)
Note:
* Some vehicle's may have a hole
available to pass the wire through, if not,
you need to drill a hole close to the location
of camera for the connector wire, and two
holes for the screws of camera installation.
* Before you drill those holes, you must
check out and make sure no other
components too close to your aiguille.
Before drilling, we strongly commend you
remove electrical parts or fuel system
behind the vehicle door and clear the
surroundings to avoid unexpected damages.
3. If the holes are all ready, pass the connector
wire of camera into the vehicle.(Fig3)
Install the camera by two screws supplied
and adjust the camera to an proper angle.
(Fig 4)
Note:
* Generally we advise you put it on the
center of the license plate top.
(Fig2)
(Fig3)
(Fig 4)
4 . T h e n c o n n e c t t h e camera to the
t r a n s m i s s i o n b o x G T 406 5 .(Fig5)
5. Fix the transmission box Gt406 5
on the surface by the sheet screws we
supplied. (Fig6)
(Fig 5)
6. Next you'll need to find the vehicle's reverse lights. Turn off the
vehicle's reverse lights. Turn the vehicle's ignition key to the accessory
position, engage the parking brake and put the car in reverse. Look at
the vehicle's tail lights to see where the reverse lights are located, they
are the white lights.
-5-
To locate the reverse light's 12/24VDC wire
it will be necessary to gain access to the rear
of the vehicle's tail light.
For help locating the vehicle's reverse light
circuit contact your vehicle's manufacturer
for vehicle specific wiring diagrams.
(Fig6)
7.Once you have located the reverse light
circuit you will have to route the GT4062
Power Wire to that location. You must
securely fasten the Power Wire to prevent
it from being caught on any vehicle
component such as the trunk
hinge (Fig. 7). Never route the cable
outside the vehicle.
Camera's
Power Cable
(Fig7)
8.The reverse light sockets on most vehicles have two wires connected
to them. Usually the negative wire is black and the positive wire is a
colored wire. If you are uncertain about the wiring, you can use a 12/24
volt test light available at most auto parts stores to determine which is
the positive wire.
a.Remove the reverse light socket from its housing, then remove the blub
from the socket.
b.Engage the parking brake, turn the ignition key to the ON position, but
do not start the vehicle. Put the gear shift in the reverse position.
c.Attach the ground wire of the test light to the vehicle ground, then
touch one of the socket's contacts with the positive lead.
d. If the test light lights up, then the wire corresponding to that contact
is the positive wire. If it doesn't light up the opposite wire is the
positive wire.
Follow the manufacturer's instructions for the safe use of the test light.
9. After determining which wire is the positive and which is the negative,
turn off the ignition key, then remove the battery's negative cable.
-6-
10. Following the In-Line Wire Connector Instructions section, splice the
Red wire using the supplied In-Line Wire Connector to the reverse light's
positive(+) wire. Use a set of slip joint pliers to squeeze the TAP and
insure good connection.
11. Next splice the black wire of the transmission box GT4062 power
wire to the reverse light's negative(-) wire or ground.
12. Replace the reverse light bulb, then reinstall the light socket. Secure
all the wire with cable ties or electrical tape. Reattach the negative
battery cable to the battery.
Wiring Connector Diagram
Gt4065 is equipped with Reverse Voltage Protection. If the camera
does not operate, please check that the Red wire is connected to positive
(+) and the Black wire is connected to negative(-).
-7-
In-Line Wire Connector Instructions
Insert the existing
wire to be tapped.
Insert the wire to
be attached.
Crimp tap then
close lock
You do not need to use the In-Line Wire Connectors. GT4062 can be
wired directly to the reverse light circuit by stripping the reverse light
wires then twisting GT4062 wires to the exposed reverse light wires.
Once connected, wrap with electrical tape. Do not attempt this if you
are not knowledgeable with electrical installation practices.
4-2:12/24 Voltage Cigarette Lighter Adapter and
2.4GHz wireless Receiver Gt4013 Using
1. Plug the end of the power cable into the
electric equipment.
2.Plug the end of the AV cable into the AV
equipment
3. Plug the 12/24 V car power adapter into
car power socket.
4. The monitor or GPS will be automatically activated when you back up the car.
The monitor will be automatically shut when the car goes forward.
4-3 2.4GHz wireless Receiver Gb6904 using
1.Clamp the Gb6904 on a GPS equipment
2.the GPS equipment will supply 5V voltage to the Receiver and
the Receiver can supply AV signal to GPS.
3.The monitor of GPS will be automatically activated when you
clamp the Receiver
-8-
5. SPECIFICATIONS
GL8902+GT4065
510
Horizontal View Angle
+12V DC
150mA
(Max.)
RECEIVERGT4013
586(PAL)
ISM 2,400-2,483MHz
2mW/FCC,10wm/CE
<0.5 Lux
4m
Minimum Illumination
IR Night Range
RECEIVERGB4096
496(NTSC)
628
80 degree
FM
ISM 2,400-2,483MHz
12V/24V DC
Modulation
Input voltage
Output current
Output Voltage
Received Sensitivity
Consumption Current (Max.)
1.5A
5V
≤-85dBm
1.5A
FM
ISM 2,400-2,483MHz
5V DC
Modulation
Input voltage
Output current
Video output level
Received Sensitivity
Video output impedance
110mA
1.1Vpp
≤- 93 dBm
75Ω
-9-
FCC INFORMATION
This device complies with part15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
-10-
GOSPELL Smarthome Electronic CO.,LTD.
4-5Floor/Block 2, Vision (SZ) Park, Hi-Tech Industrial Park, Shenzhen, P.R.China

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2009:01:07 09:24:33+08:00
Create Date                     : 2009:01:07 09:24:33+08:00
Format                          : application/pdf
Title                           : 8907AZ-OEM XIAO.cdr
Creator                         : qibt
Document ID                     : uuid:643f43d1-c1b1-4d39-88cd-e7c61138e17e
Instance ID                     : uuid:5f722f53-4e36-4815-ae3a-7b92e8313722
Page Count                      : 12
Author                          : qibt

EXIF Metadata provided by EXIF.tools