Gospell Smarthome Electronic Y5703 HD WiFi Camera User Manual Y5703GAA

Shenzhen Gospell Smarthome Electronic Co., Ltd. HD WiFi Camera Y5703GAA

15_Y5703GAA UserMan

HD WiFi Camera Model: Y5703GAABefore using the product, please read the guide carefully to avoidany damages to the product in virtue of faulty operation or misuse.-03-Quick Start Guide※All parameters change without prior notice, The finial right of interpretation is reserved by the company.-04--07- Troubleshooting-06- 2. In setting page of app (Fig. 11), click “Delete device” to remove the connected camera, can remove the bonding with the account. Tips6. Push message: when movement is detected, alarm message can be sent to server and pushed to your phone.9.When this machine has a crash fault or other abnormal conditions influencing the usage, it is recommended to cut out the power and restart; or press SET key for 10 seconds, which can restore factory settings, and then please reconnect the router.1. Suggest using qualified micro-SD card to avoid incompatibility. Format micro-SD card before using.5. Cancel"sharing with friends": Delete the camera and cancel "sharing with friends". (You have to re-add the camera to use it again) 8.Only support the special characters in English mode, such as: " @, #, &, *, ~, ｛, ｝, -, =, +, /, ?, (, )", Dont support the special characters, such as:"%", "\", "<>". -08-FCC/CE Certification Information(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. Hereby, we declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.Notice: Observe the national local regulations in the location where the device is to be used. This device may be restricted for use in some or all member states of the European Union (EU).- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-02-1. 2.4G wireless router is required. 2. Support Android 4.4 and above, iOS 8.0 and above 3. Download APP: Scan the QR code below and complete the installation4. Add a device: Open the APP home page.click the “Add Device” icon to connect your camera. According to the settings guide in the APP, you can configure multiple cameras at the same time.1. Find the power interface behind the product and power on the camera,The indicator will turn on.2. Please make sure there is WiFi available. Connect to the power supplyCamera Indicator Instruction-05--01-7. Remote monitoring: after the camera is connected to Internet successfully, you can monitor your home anywhere ,anytime.4. Sharing with Friends: Share your QR code to your friends. 3. Movement detection: when movement is detected within the scope of camera, the camera will record video and take photos automatically. Videos and photos will be saved in micro-SD card.Indicates that power failure or network not connected.Red indicator remainsRed indicator flashesIndicates that camera is connecting to network.Green indicator flashesIndicates the router connected successfully (no Internet).Green indicator remainsIndicates the camera is connected to server and working well. d) Ensure that SSID and password are no longer than 16 characters e) Ensure that SSID is broadcasted. f ) Ensure that the DHCP is enabled on router. g) Ensure that Wi-Fi encryption method is WPA2-PSK/ WPA-PSK or AES. h) Ensure that Wi-Fi signal is 2.4GHz. i ) Ensure that there is no MAC filter on router or add MAC address to router whitelist j ) We suggest rebooting the router, and the "security settings, encryption method" of WiFi password should never choose "auto-select". k ) Reset the camera to set up connection again. Press and hold SET key for 5 seconds. 2. Red indicator remains, network connection is failed. a) Ensure that the password of Wi-Fi is correct. b) Ensure that the network connects to Internet freely. c) Ensure that the camera is in range of Wi-Fi hotspot.3. Green indicator flashes, connection to server failed. a) Ensure that Wi-Fi signal is strong enough and bandwidth is enough for connection. Move near to Wi-Fi hotspot or increase the bandwidth. b) Ensure that camera is not under interferon of other 2.4GHz signal. b) Ensure that camera is in range of router. Keep the distance less than 40fts between router and indoor camera, less than 65fts for outdoor camera. c) Ensure that SSID and password of Wi-Fi contains no special characters. Modify the SSID and password of Wi-Fi with only English characters, no special characters. 1. Wi-Fi cannot be connected a) Ensure that the antenna of camera is fixed well.Imaging sensorEffective pixelHorizontal viewing angleWireless transmission wayTransmission RangeInterfaceRemote monitor1/4",CMOS100W pixels85±5°WiFiIndoor: 20m Set ButtonSupport Android and IOSPower supply 5V 1A, DC Screws Power adapter USB cable ※ The picture is only for reference and the real object shall prevail43 Technical ParametersPacking List Appearance Installation21 657 8 9 Camera User manual HD WiFi C amera Mode l: T570 3GABBefor e using t he prod uct, pl ease re ad the gu ide car efull y to avoi dany dam ages to t he prod uct in vi rtue of f aulty o perat ion or mi suse.Qui ck Star t GuideLight sensor Camera lensLED indicating lampSet buttonBaseMIC holeUSB portLoudspeaker正面反面IOSAndroidMicro USB

Navigation menu