Graco 312066Z Reactor Electric Proportioners Users Manual 312066Z, Reactor, Proportioners, Repair Parts, (English)
2015-04-02
: Graco Graco-312066Z-Reactor-Electric-Proportioners-Users-Manual-686245 graco-312066z-reactor-electric-proportioners-users-manual-686245 graco pdf
Open the PDF directly: View PDF 
.
Page Count: 74
| Download | |
| Open PDF In Browser | View PDF |
Repair - Parts 312066Z EN Electric, Heated, Plural Component Proportioner. For spraying polyurethane foam and polyurea coatings. For professional use only. Not approved for use in European explosive atmosphere locations. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 3 for model information, including maximum working pressure and approvals. Model E-XP1 Shown TI10953a 9902471 Conforms to ANSI/UL Std. 499 Certified to CAN/CSA Std. C22.2 No. 88 Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplied Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Temperature Control Diagnostic Codes . . . . . . . . 8 E01: High fluid temperature . . . . . . . . . . . . . . . . 8 E02: High zone current . . . . . . . . . . . . . . . . . . . . 9 E03: No zone current . . . . . . . . . . . . . . . . . . . . 10 E04: Fluid Temperature Sensor (FTS) or thermocouple disconnected . . . . . . . . . . . . 10 E05: Circuit board overheated . . . . . . . . . . . . . 10 E06: Communication cable unplugged . . . . . . . 10 Motor Control Diagnostic Codes . . . . . . . . . . . . . 11 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 E21: No component A transducer . . . . . . . . . . . 12 E22: No component B transducer . . . . . . . . . . . 12 E23: High fluid pressure . . . . . . . . . . . . . . . . . . 12 E24: Pressure Imbalance . . . . . . . . . . . . . . . . . 12 E25: High line voltage . . . . . . . . . . . . . . . . . . . . 14 E26: Low line voltage . . . . . . . . . . . . . . . . . . . . 14 E27: High Motor Temperature . . . . . . . . . . . . . 14 E28: High current in motor . . . . . . . . . . . . . . . . 14 E29: Brush Wear . . . . . . . . . . . . . . . . . . . . . . . . 14 E31: Motor Control Failure (E-30 and E-XP2 only) . . . . . . . . . . . . . . . . 15 E32: Motor Control Overtemperature . . . . . . . . 16 Communication Diagnostic Codes . . . . . . . . . . . 16 E30: Momentary loss of communication . . . . . . 16 E99: Loss of communication . . . . . . . . . . . . . . . 16 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Reactor Electronics . . . . . . . . . . . . . . . . . . . . . . 18 Primary Heaters (A and B) . . . . . . . . . . . . . . . . 20 Hose Heat System . . . . . . . . . . . . . . . . . . . . . . 21 2 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Before Beginning Repair . . . . . . . . . . . . . . . . . . 23 Pressure Relief Procedure . . . . . . . . . . . . . . . . 23 Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Pump Removal . . . . . . . . . . . . . . . . . . . . . . . . . 24 Pump Installation . . . . . . . . . . . . . . . . . . . . . . . . 26 Drive Housing . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Motor Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Capacitor Test . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Circuit Breaker Module . . . . . . . . . . . . . . . . . . . 32 Electric Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Motor Control Board . . . . . . . . . . . . . . . . . . . . . 34 Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Electric Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Temperature Control Module . . . . . . . . . . . . . . . 37 Primary Heaters . . . . . . . . . . . . . . . . . . . . . . . . . 40 Heated Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Fluid Temperature Sensor (FTS) . . . . . . . . . . . . 44 Display Module . . . . . . . . . . . . . . . . . . . . . . . . . 46 Inlet Fluid Strainer Screen . . . . . . . . . . . . . . . . . 48 Pump Lubrication System . . . . . . . . . . . . . . . . . 48 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Reactor Assembly (Model E-XP1 Shown) . . . . . 50 Parts Used on All Models . . . . . . . . . . . . . . . . . 53 Parts that Vary by Model . . . . . . . . . . . . . . . . . . 54 Sub Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . 58 Proportioner Module . . . . . . . . . . . . . . . . . . . . . 58 Fluid Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 7.65 kW Single Zone Fluid Heater . . . . . . . . . . . 61 Reactor Frame . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Temperature Control . . . . . . . . . . . . . . . . . . . . . 64 Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Fluid Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Circuit Breaker Modules . . . . . . . . . . . . . . . . . . 67 248669 Conversion Kit . . . . . . . . . . . . . . . . . . . . . 71 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 74 Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 74 312066Z Models Models E-20 SERIES Part, Series Full Load Peak Voltage Amps* (phase) 259025, E 259030, E 259034, E 48 24 32 230V (1) 400V (3) 230V (3) System Watts† Primary Heater Watts Max Flow Rate◆ lb/min (kg/min) Approximate Output per Cycle Maximum Fluid (A+B) Working Pressure gal. (liter) psi (MPa, bar) 10,200 10,200 10,200 6,000 6,000 6,000 20 (9) 20 (9) 20 (9) 0.0104 (0.04) 0.0104 (0.04) 0.0104 (0.04) System Watts† Primary Heater Watts Max Flow Rate◆ lb/min (kg/min) Approximate Output per Cycle Maximum Fluid (A+B) Working Pressure gal. (liter) psi (MPa, bar) 17,900 17,900 17,900 23,000 23,000 23,000 10,200 10,200 10,200 15,300 15,300 15,300 30 (13.5) 30 (13.5) 30 (13.5) 30 (13.5) 30 (13.5) 30 (13.5) 0.0272 (0.1034) 0.0272 (0.1034) 0.0272 (0.1034) 0.0272 (0.1034) 0.0272 (0.1034) 0.0272 (0.1034) System Watts† Primary Heater Watts Max Flow Rate◆ gpm (lpm) Approximate Output per Cycle Maximum Fluid (A+B) Working Pressure gal. (liter) psi (MPa, bar) 15,800 15,800 15,800 10,200 10,200 10,200 1.0 (3.8) 1.0 (3.8) 1.0 (3.8) 0.0104 (0.04) 0.0104 (0.04) 0.0104 (0.04) System Watts† Primary Heater Watts Max Flow Rate◆ gpm (lpm) Approximate Output per Cycle Maximum Fluid (A+B) Working Pressure gal. (liter) psi (MPa, bar) 23,000 23,000 23,000 15,300 15,300 15,300 2.0 (7.6) 2.0 (7.6) 2.0 (7.6) 0.0203 (0.0771) 0.0203 (0.0771) 0.0203 (0.0771) 2000 (14, 140) 2000 (14, 140) 2000 (14, 140) E-30 SERIES Part, Series Full Load Peak Voltage Amps* (phase) 259026, F 259031, F 259035, F 259057, F 259058, F 259059, F 78 34 50 100 62 35 230V (1) 400V (3) 230V (3) 230V (1) 230V (3) 400V (3) 2000 (14, 140) 2000 (14, 140) 2000 (14, 140) 2000 (14, 140) 2000 (14, 140) 2000 (14, 140) E-XP1 SERIES Part, Series Full Load Peak Voltage Amps* (phase) 259024, E 259029, E 259033, E 69 24 43 230V (1) 400V (3) 230V (3) 2500 (17.2, 172) 2500 (17.2, 172) 2500 (17.2, 172) E-XP2 SERIES Part, Series 259028, F 259032, F 259036, F Full Load Peak Voltage Amps* (phase) 100 35 62 230V (1) 400V (3) 230V (3) 3200 (22, 220) 3200 (22, 220) 3200 (22, 220) * Full load amps with all devices operating at maximum capabilities. Fuse requirements at various flow rates and mix chamber sizes may be less. † Total system watts, based on maximum hose length for each unit: • • E-20 and E-XP1 series, 210 ft (64 m) maximum heated hose length, including whip hose. E-30 and E-XP2 series, 310 ft (94.5 m) maximum heated hose length, including whip hose. ◆ Maximum flow rate given for 60 Hz operation. For 50 Hz operation, maximum flow rate is 5/6 of 60 Hz maximum flow. 312066Z 3 Supplied Manuals Supplied Manuals Related Manuals The following manuals are shipped with the Reactor™ Proportioner. Refer to these manuals for detailed equipment information. The following manuals are for accessories used with the Reactor™. Order Part 15M334 for a compact disk of Reactor manuals translated in several languages. Manuals are also available at www.graco.com. Order Part 15M334 for a compact disk of Reactor manuals translated in several languages. Reactor Data Reporting Kit Part Description Reactor Electric Proportioner 309867 Instruction-Parts Manual (English) Part Description Fusion Spray Gun 312065 Reactor Electric Proportioner, Operation Manual (English) Part Description 309550 Instruction-Parts Manual (English) Reactor Electrical Diagrams Heated Hose Part Description Part Description 312067 Reactor Electric Proportioner, Electrical Diagrams (English) 309572 Instruction-Parts Manual (English) Displacement Pump Part Description 309577 Electric Reactor Displacement Pump Repair-Parts Manual (English) Circulation and Return Tube Kit Part Description 309852 Instruction-Parts Manual (English) Rupture Disk Assembly Kit Part Description 312416 Instruction-Parts Manual (English) Electric Reactor Installation 4 Part Description 310815 Instruction Manual (English) 312066Z Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING ELECTRIC SHOCK HAZARD Improper grounding, setup, or usage of the system can cause electric shock. • Turn off and disconnect power cord before servicing equipment. • Use only grounded electrical outlets. • Use only 3-wire extension cords. • Ensure ground prongs are intact on sprayer and extension cords. • Do not expose to rain. Store indoors. TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed. • Read MSDS’s to know the specific hazards of the fluids you are using. • Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines. • Always wear impervious gloves when spraying or cleaning equipment. PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to: • Protective eyewear • Clothing and respirator as recommended by the fluid and solvent manufacturer • Gloves • Hearing protection SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Engage trigger lock when not spraying. • Do not point gun at anyone or at any part of the body. • Do not put your hand over the spray tip. • Do not stop or deflect leaks with your hand, body, glove, or rag. • Do not spray without tip guard and trigger guard installed. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. • Tighten all fluid connections before operating equipment. • Check hoses and couplings daily. Replace worn or damaged parts immediately. 312066Z 5 Warnings WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • Use and clean equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc). • Keep work area free of debris, including solvent, rags and gasoline. • Do not plug or unplug power cords or turn lights on or off when flammable fumes are present. • Ground equipment, personnel, object being sprayed, and conductive objects in work area. See Grounding instructions. • Use only Graco grounded hoses. • Check gun resistance daily. • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem. • Do not flush with gun electrostatics on. Do not turn on electrostatics until all solvent is removed from system. • Keep a working fire extinguisher in the work area. THERMAL EXPANSION HAZARD Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure due to the thermal expansion. Over-pressurization can result in equipment rupture and serious injury. • Open a valve to relieve the fluid expansion during heating. • Replace hoses proactively at regular intervals based on your operating conditions. PRESSURIZED ALUMINUM PARTS HAZARD Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • This equipment is for professional use only. • Do not leave the work area while the equipment is energized or under pressure. Turn off all equipment and follow Pressure Relief Procedure in this manual when the equipment is not in use. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or over bend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. 6 312066Z Warnings WARNING MOVING PARTS HAZARD Moving parts can pinch or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply. BURN HAZARD Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely. 312066Z 7 Temperature Control Diagnostic Codes Temperature Control Diagnostic Codes Temperature control diagnostic codes appear on temperature display. These alarms turn off heat. E99 clears automatically when communication is regained. Codes E03 through E06 can be cleared by pressing turn main power OFF . For other codes, then ON to Code Code Name Alarm Zone Corrective Action page 01 High fluid temperature Individual 8 02 High zone current Individual 9 03 No zone current with hose heater on Individual 10 04 FTS not connected Individual 10 05 Board overtemperature Individual 10 06 Communication cable unplugged from module Individual 10 99 Loss of communication ALL 16 clear. For hose zone only, if FTS is disconnected at startup, display will show hose current 0A. E01: High fluid temperature Causes of E01 Errors • Thermocouple A or B (310) senses a fluid temperature above 230°F (110°C). • Fluid temperature sensor (FTS) senses a fluid temperature above 230°F (110°C). • Overtemperature switch A or B (308) senses a fluid temperature above 230°F (110°C) and opens. At 190°F (87°C) the switch closes again. • Thermocouple A or B (310) fails, is damaged, is not touching the heater element (307), or has a poor connection to the temperature control board. • • Overtemperature switch A or B (308) fails in the open position. The temperature control board fails to turn off any heat zone. • Zone power wires or thermocouples are switched from one zone to another. • Failed heater element where thermocouple is installed. • Loose wire • On 6.0 and 10.2 kW heater models only: Jumper wire on J1 connector, between module (3) and display (4), is loose or incorrectly wired. 8 Checks Troubleshooting this equipment requires access to parts that may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician perform all electrical troubleshooting. Be sure to shut off all power to the equipment before repairing. Check which zone is displaying the E01 error. 1. Check that connector B is firmly plugged into temperature control board (see FIG. 5, page 37). 2. Clean and re-plug connections. 3. Check connections between the temperature control board and overtemperature switches A and B (308), and between temperature control board and thermocouples A and B (310) or FTS (21) [depending on which zone is displaying E01]. See Table 5, page 37. Ensure that all wires are securely connected to connector B. 312066Z Temperature Control Diagnostic Codes 4. Remove connector B from temperature control module, and check continuity of overtemperature switches A and B, thermocouples A and B, or FTS by measuring resistance across the pins on the plug end; see TABLE 1. Before doing the following checks, note which zone (A, B, FTS, or all) has high fluid temperature. E02: High zone current 1. Turn main power OFF . 2. Relieve pressure, page 23. Disconnect whip hose. Table 1: Sensor Connector Continuity Checks Pins 1&2 3&4 5&6 8&9 11 & 12 10 & 12 Description OT switch A OT switch B Thermocouple A Thermocouple B FTS FTS Reading nearly 0 ohms nearly 0 ohms 4-6 ohms 4-6 ohms approximately 35 ohms per 50 ft (15.2 m) of hose, plus approximately 10 ohms for FTS open 5. Verify fluid temperature, using an external temperature sensing device. • If temperature is too high (sensor reading is 229°F [109°C] or above): 3. Disconnect hose connector (D) at Reactor. 4. Using an ohmmeter, check between the two terminals of the connector (D). There should be no continuity. 5. Exchange zone module with another one. Turn zone on and check for error. If error disappears, replace faulty module. For hose zone: If error still occurs, perform Transformer Primary Check and Transformer Secondary Check starting on page 45. When there is a a high current error, the LED on that zone’s module will turn red while the error is displayed. 6. Check if thermocouples A and B are damaged, or not contacting the heater element, page 42. 7. To test that temperature control module turns off when equipment reaches temperature setpoint: a. Set temperature setpoints far below displayed temperature. b. Turn zone on. If temperature rises steadily, power board is failing. c. Verify by swapping with another power module. See Replacing Temperature Control Assembly Modules, page 38. d. If the swapped module does not fix the problem, the power module is not the cause. 8. Verify continuity of heater elements with an ohmmeter, see page 40. 312066Z 9 Temperature Control Diagnostic Codes E03: No zone current 1. Check for tripped circuit breaker inside electrical cabinet or at power source for that zone. Replace circuit breaker if it trips habitually. 2. Check for loose or broken connection at that zone. 3. Exchange zone module with another one. Turn zone on and check for error (see page 38). If error disappears, replace faulty module. 4. If E03 occurs for all zones, the contactor may not be closing. Verify wiring from heater control to contactor coil. a. Hose zone: test hose continuity, page 43. b. Perform Transformer Primary Check and Transformer Secondary Check, starting on page 45. When a no current error occurs, the LED on the specific zone’s module turns red when the error is displayed. E04: Fluid Temperature Sensor (FTS) or thermocouple disconnected 1. Check temperature sensor connections to long green connector (B) on temperature control module, page 37. Unplug and re-plug sensor wires. 2. Test fluid temperature sensor continuity with ohmmeter, page 8. 3. If an error occurred for the hose zone, check FTS connections at each section of hose. 5. To verify heater control module is not causing the problem, use a wire to short-circuit the two pins corresponding to the FTS (red and yellow for A or B zone, red and purple for hose). The display will show the control heater module temperature. 6. If an error occurred for the hose zone, temporarily use the current control mode. Refer to Reactor Operation manual 312062. E05: Circuit board overheated Each module has an on-board temperature sensor. Heat is turned off if module temperature exceeds 185°F (85°C) within the heater module. 1. Check that fan above electrical cabinet is operating. 2. Check that electrical cabinet door is properly installed. 3. Check for obstructions blocking cooling holes in bottom of electrical cabinet. 4. Clean heatsink fins behind heater control modules. 5. Ambient temperature may be too high. Allow Reactor to cool by moving to a cooler location. E06: Communication cable unplugged 1. Unplug and re-plug cable that connects heater control module to heater module. 2. Replace communication cable if problem persists. 4. If an error occurred for the hose zone, test FTS by plugging directly into machine. F D TI10964a 10 312066Z Motor Control Diagnostic Codes Motor Control Diagnostic Codes Motor control diagnostic codes E21 through E29 appear on pressure display. Warnings There are two types of motor control codes: alarms and warnings. Alarms take priority over warnings. Reactor will continue to run. Press to clear. A warning will not recur for a predetermined amount of time (varies for different warnings), or until main power Alarms is turned OFF then ON . Alarms turn off Reactor. Turn main power OFF Code then ON Code Name to clear. Alarm (A) or Corrective Warning (W) Action page 21 No transducer (component A) A 16 Alarms can also be cleared, except for code 23, by 22 No transducer (component B) A 16 pressing 23 High fluid pressure A 16 24 Pressure imbalance A/W (to select, see page 34) 16 25 High line voltage A 18 26 Low line voltage A 18 27 High motor temperature A 18 28 High current A 29 29 Brush wear W 19 30 Momentary loss of communication - 16 31 Motor control failure A 15 32 Motor control overtemperature A 16 99 Loss of communication - 16 312066Z . 11 Motor Control Diagnostic Codes E21: No component A transducer b. Turn on the Reactor master power. • 1. Check transducer A connection at J3 on motor control board, page 34, and clean contacts. 2. Reverse A and B transducer connections. If error moves to transducer B (E22), replace transducer A, page 36. If error does not move, replace motor control board, page 34. E22: No component B transducer 1. Check transducer B connection at J8 on motor control board, page 35, and clean contacts. • 4. If the error persists and no root cause is found through the above testing, replace the motor control board, page 34. E24: Pressure Imbalance If the pressure difference between components A and B exceeds 500 psi (3.5 MPa, 35 bar), an E24 will occur. This default value is adjustable; see the operation manual. 2. Reverse A and B transducer connections. If error moves to transducer A (E21), replace transducer B, page 36. If error does not move, replace motor control board, page 34. E24 can be an alarm or a warning, as desired. Set DIP switch on motor control board ON for alarm, OFF for warning. See page 34. E23: High fluid pressure 1. Relieve pressure. Verify low pressure with analog gauges. Turn main power OFF then ON If the error is gone, turn off the Reactor main power, remove test transducer, and replace “A” transducer. If the error persists, unplug the “test” transducer from the “A” socket, and reinstall the “A” pressure transducer back into the “A” socket. Repeat this test procedure on the “B” side. Fast E24 Errors Fast E24 errors occur: . If error persists, do checks below. 1. Check the jumpers and the wiring. Check jumper on motor control board J10 for E20 and E-XP1, or J7 for E30 and E-XP2, pins 7-10, page 34. 2. Remove, clean and re-install the pressure transducer leads If the jumpers and the wiring are in good working condition and you still have the error, then you will need to replace the “A” and “B” pressure transducers. 3. To determine if it’s the “A” or the “B” transducer, you will need a known good Reactor pressure transducer to use as a “test” transducer. The test is done without removing the existing pressure transducers from the fluid manifold. • • within 10 seconds of turning the pumps on, or as soon as you trigger the gun. Causes of Fast E24 Errors • • • • • • • • one side of the gun is plugged. a pressure transducer has failed. damaged pump seals or check valve. no feed pressure or empty material drum plugged heater. plugged hose. plugged manifold. one PRESSURE RELIEF/SPRAY valve is leaking or is set to PRESSURE RELIEF/CIRCULATION a. Unplug the “A” transducer from the Motor control board socket (page 36) and replace with “test” transducer. 12 312066Z Motor Control Diagnostic Codes Checks for Fast E24 Errors If a fast E24 error occurs, first check the readings of the analog gauges. 1. Swap the transducer plug-ins on the motor control board. (J3 and J8 for the E-20 and E-XP1. J3 and J5 for the E30 and E-XP1). 2. Repeat above test. 3. If the problem stays with the same side as before, then the pressure transducer is bad. If gauge pressures are very close 1. Clear the error and run the unit. 4. If the problem switches to the other transducer, then the problem is in the motor control boards socket. 2. Check plug J10 (E20/E-XP1) or J7 (E30/E-XP2) or the jumpers 7 to 8, or 9 to 10 on the motor control board. If the gauge readings are not equal. 3. Check pressure transducer performance: The digital display on a Reactor always shows the higher of the two pressures. As soon as the higher analog pressure drops below the lower analog pressure the digital display will switch to the new highest reading. Determine which transducer is performing poorly. 1. For testing purposes only, find the dip switches labeled SW2 on the motor control board, page 35. Set dips witch 3 to OFF. This will allow the Reactor to run with a pressure imbalance alarm. 2. Run the unit to build up some pressure (1000 – 1200 psi). Shut down the unit, clear the alarm and power back up. Do not depressurize the unit. 3. Check the analog gauges to see which pressure is higher. Check if the display pressure matches, indicating that the motor control board “sees” that transducer. If not, the motor control board does not “see” that transducer. Check the wire connections and or replace the transducer. 4. With the pump zone off, use the pressure relief valves to slowly relieve the “high” side pressure, while watching the digital display and the analog gauges. Once the higher analog gauge drops below the lower analog pressure the motor control board should start reading the “new” high side pressure (because it is now the higher of the two). Continue dropping the original “high” side pressure - the digital display should stop dropping. Repeat the process to check the other pressure transducer. The last test determines if the pressure transducer has failed or if the socket on the pressure control board has gone bad. 1. Clear the error and balance the pressures using the dump valves. 2. If you cannot get the pressures to balance: • Check for pump failure. • Check for adequate material. • Using the feed pump to push fluid out through the gun manifold, check for a plugged fluid path. • Run the unit. • Check and clean the gun inlet screens. • Check and clean the mix chamber “A” and “B” impingement ports a well as the center port. Note: Some mix chambers have counter bored holes, and require two drill sizes to clean impingement ports completely. “Slow” E24: • Possible Causes: • • • • • • • • • 312066Z When spraying, gradual pressure imbalance and eventual E24. One side of the Gun is partially blocked. The “A” or the “B” pump on the Reactor has failed. The “A” or the “B” feed pump has failed. The “A” or the “B” feed pump pressure is set too high. The “A” or the “B” inlet screen is plugged. The hose is not heating properly. Kinked supply hose. Bottom of the drum is damaged causing a blockage to the inlet of the feed pump. The drum is not vented properly. 13 Motor Control Diagnostic Codes E25: High line voltage E28: High current in motor Supply voltage too high. Check Reactor voltage requirements, page 73. Check motor control board: 1. Turn the master power off. E26: Low line voltage Supply voltage too low. Check Reactor voltage requirements, page 73. 2. Disconnect socket J4 (E-20/E-XP1) J1 (E-30/E-XP2) on the motor control board. 3. Turn the master power back on. E27: High Motor Temperature 4. If the E28 error did not go away then there is a problem with the motor control board. Replace board, page 34. 1. Motor temperature too high. Reduce pressure, gun tip size, or move Reactor to a cooler location. Allow one hour for cooling. Check motor: 1. Check to see if the motor rotates freely. 2. Check fan operation. 2. Check to see if the brushes are damaged. 3. Ensure there is no obstruction around the fan area that would cause lack of airflow; ensure the motor/fan shroud is installed. 4. Ensure the unit is being operated with the front cover on. 5. Ensure the brush wear/over temp switch wire assembly is plugged into J7 (E-20/E-XP1) or J6 (E-30/E-XP2) of the motor control board. 6. With the main power off, unplug the wire harness from J7 (E-20/E-XP1) or J6 (E-30/E-XP2) on the motor control board and install a jumper wire on pins 1 and 2. Turn the main power back on. If E27 is gone: If the E27 error is gone and the motor is truly not overheated, then the problem can be in the motor/motor wire harness assembly. Measure the resistance between the two yellow wires that go to pins 1 and 2 of the motor connector. If there is an open connection, the thermal overload switch is open or there is a broken wire inside the motor, or a broken wire in the motor harness. If the E27 error code is still there, double check if pins 1 and 2 are jumpered properly. If jumpered properly, then it would appear that the problem is with in the motor control board. 14 3. Check that the voltage going to the motor is good. 4. Check the three wire (yellow, yellow, orange) motor connector to the motor board. A gentle tug on each wire individually at the connector should identify the loose wire. If a wire pulls out, bend the locking tab on the crimp end, insert the wire until it seats and repeat gentle tug. 5. If the above does not resolve the problem, replace the motor, page 33. E29: Brush Wear CAUTION Prolonged operation of motor after a brush wear warning may result in failure of motor and motor control board. 1. Check for normal brush wear, which causes the brush sensor to come in contact with the motor commutator. Replace the brushes, page 30. 2. Check spade plug. The spade plug inside the motor housing may be twisted and contacting the commutator side of the brush sensor assembly, causing a false alarm. Follow the orange wire coming from J7 (E-20/E-XP1), or J6 (E-30/E-XP2), up to the spade connector on the motor. Using a flashlight, ensure the spade plug assembly is not making contact with the metal housing of the brush assembly. 312066Z Motor Control Diagnostic Codes 3. Check wiring. The orange brush sensor wire coming out of the brush may be routed online with the commutator wiring (thick red wire), causing a false alarm. Reroute the orange wire coming out of the brush, away from the commutator wiring. 1. Turn main power OFF . Disconnect power supply. 4. Check motor control board. • • • • Remove the plug in J7 (E-20/E-XP1), or J6 (E-30/E-XP2). (This will cause an E27 alarm). To remove the E27 alarm, use a jumper wire on the motor control board, across the two pins that the two yellow wires plug into. Then turn the unit on. The E27 as well as the E29 alarm should be gone. If the E27 alarm is not gone double-check your jumper. If the jumper is installed correctly and the E29 alarm is still there, replace the motor control board, page 34. E31: Motor Control Failure (E-30 and E-XP2 only) The E31 error code represents a motor drive error. This indicates that the 24G881 motor control board has malfunctioned and needs to be replaced. A motor control board failure may also be indicated by the motor starting up immediately upon the application of power to the sys- Wait 5 minutes for stored voltage to discharge (E-30 and E-XP2 models only). 2. Relieve pressure, page 23. 3. Perform the following inspections. a. Motor failure: Inspect the motor commutator by removing the top brush (see Brush Removal, page 30). Rotate the motor, inspecting the whole commutator for burns, pocking, or shorts between poles. Continue rotating the motor for a complete pump cycle, up and down, to ensure that there is no mechanical interference or restriction in the pump lower or gear drive system. b. Capacitor failure: Inspect and test the motor start capacitor, following the Capacitor Test instructions on page 32. c. tem, without pressing . This is an indication that the output drivers of the motor control have shorted out and are delivering full power to the motor at all times. The cause of the failure may be one of the following conditions: motor failure, capacitor failure, shorted or frayed wiring, or inadequate power supply. Perform the following procedure before replacing the motor control board. Shorted or frayed wiring: Inspect all wiring connected to the motor control board and the motor, for shorts or frayed insulation. Replace any compromised wires with wire of the same gauge, color. and temperature rating. d. Inadequate power supply: Verify that the power source is of the correct voltage and current rating for the system, and that all phases are properly connected. Ensure that the power does not dip or surge during operation. Prior to shutting down the generator, ensure that the motor has stopped and the main disconnect is opened. If the generator is stopped during operation, even due to running out of fuel, the drop in supply voltage may cause a motor drive failure. 312066Z 15 Communication Diagnostic Codes E32: Motor Control Overtemperature The E32 error code indicates a high temperature condition within the motor control board (701). This could be caused by an abnormally high ambient temperature in the work location, blockage of cooling vents in the cabinet, or the failure of the cooling fan inside the cabinet. 1. Relieve pressure, page 23. Verify low pressure with analog gauges. 2. Turn main power OFF then ON . If error still remains, identify cause of the overtemperature condition and remedy. Communication Diagnostic Codes E30: Momentary loss of communication Communications between the display and the motor control board or the temperature control board have been momentarily lost. Normally, when communication is lost, the corresponding display will show E99. The corresponding control board will register E30 (The red LED will flash 30 times). If communications are reconnected, the display can show the E30 for a short time (no more than about two seconds). It should not be possible for E30 to be shown continuously, unless there is a loose connection causing the display and the board to continuously lose and regain communication. Check all wiring between the display and the corresponding control board. E99: Loss of communication Communications between the display and the motor control board or the temperature control board has been lost. When communication is lost, the corresponding display will show E99. 1. Check all wiring between the display and the corresponding control board. Pay close attention to the wire crimping on plug J13 for each board. Step 2 measures line voltage and should be done by a qualified electrician. If work is not performed properly it may cause electric shock or other serious injury. 2. Measure the incoming voltage to the board (it should be ~ 230Vac). 3. If it was only receiving 1 leg of the 230Vac the board may light up, and still not function properly. Correct the incoming voltage problem. 16 312066Z Troubleshooting Troubleshooting PROBLEM Reactor does not operate. CAUSE No power. SOLUTION Plug in power cord. Turn main power ON . Turn circuit breakers ON, page 32. Motor does not operate. Fan not working. Pump output low. Red stop button circuit open. Check button connections. See page 46 and electrical diagrams. Loose connections. Check connections at motor control board. Circuit breaker tripped. Reset breaker (CB5), page 32. Check 230Vac at output of breaker. Worn brushes. Check both sides. Length must be 0.7 in. (17 mm) minimum. To replace, page 30. Broken or misaligned brush springs. Realign or replace, page 30. Brushes or springs binding in brush holder. Clean brush holder and align brush leads for free movement. Shorted armature. Replace motor, page 33. Check motor commutator for burn spots or other damage. Remove motor. Have motor shop resurface commutator, if possible. Damaged motor control board. Replace board. See page 34. Blown fuse. Replace, page 36. Loose wire. Check. Defective fan. Replace, page 36. Obstructed fluid hose or gun; fluid hose ID too small. Open, clear; use hose with larger ID. Worn piston valve or intake valve in displacement pump. See pump manual. Pressure setpoint too high. Reduce setpoint and output will increase. Fluid leak in pump packing nut area. Worn throat seals. No pressure on one side. 312066Z Replace. See pump manual. Fluid leaking from heater inlet rupture Check if heater (2) and PRESSURE disk (314). RELIEF/SPRAY valve (SA or SB) are plugged. Clear. Replace rupture disk (314) with a new one; do not replace with a pipe plug. 17 Troubleshooting Reactor Electronics 2. Turn main power OFF . 3. Allow equipment to cool. Before performing any troubleshooting procedures: 1. Relieve pressure, page 23. PROBLEM Try the recommended solutions in the order given for each problem, to avoid unnecessary repairs. Also, determine that all circuit breakers, switches, and controls are properly set and wiring is correct before assuming there is a problem. CAUSE SOLUTION Plug in power cord. Both sides of display do not illuminate. Temperature display does not illuminate. Pressure display does not illuminate. Erratic display; display turns on and off. Hose display reads OA at startup. 18 No power. Turn disconnect ON . Low voltage. Ensure input voltage is within specifications, page 46. Loose wire. Check connections, page 46. Display disconnected. Check cable connections, page 46. Display disconnected. Check cable connections, page 46. Display cable damaged or corroded. Clean connections; replace cable if is damaged. Defective circuit board. Swap display connection to motor control board with connection to heater control board. If temperature display illuminates, heater control board is causing problem. Otherwise, display cable or display is failing. Display disconnected. Check cable connections, page 46. Display cable damaged or corroded. Clean connections; replace cable if is damaged. Defective circuit board. Swap display connection to motor control board with connection to heater control board. If pressure display illuminates, motor control board is causing problem. Otherwise, display cable or display is failing. Low voltage. Ensure input voltage is within specifications, page 46. Poor display connection. Check cable connections, page 46. Replace damaged cable. Display cable damaged or corroded. Clean connections; replace cable if is damaged. Display cable not grounded. Ground cable, page 46. Display extension cable too long. Must not exceed 100 ft (30.5 m) FTS disconnected or not installed. Verify proper installation of FTS (see Operation manual 312065), or adjust FTS to desired current setting. 312066Z Troubleshooting PROBLEM Display does not respond properly to button pushes. Red stop button does not work. Fan not working. 312066Z CAUSE SOLUTION Poor display connection. Check cable connections, page 46. Replace damaged cable. Display cable damaged or corroded. Clean connections; replace cable if is damaged. Ribbon cable on display circuit board Connect cable (page 46) or replace. disconnected or broken. Broken display button. Replace, page 46. Broken button (fused contact). Replace, page 46. Loose wire. Check connections, page 46. Blown fuse. Verify with ohmmeter; replace if necessary (page 46). Loose wire. Check fan wire. Defective fan. Replace, page 46. 19 Troubleshooting Primary Heaters (A and B) 2. Turn main power OFF . 3. Allow equipment to cool. Try the recommended solutions in the order given for each problem, to avoid unnecessary repairs. Also, determine that all circuit breakers, switches, and controls are properly set and wiring is correct before assuming there is a problem. Before performing any troubleshooting procedures: 1. Relieve pressure, page 23. PROBLEM CAUSE SOLUTION Heat turned off. Press Primary heater(s) does not heat. Control of primary heat is abnormal; high temperature overshoots or E01 error occurs intermittently. 20 A or B zone keys. Temperature control alarm. Check temperature display for diagnostic code, page 8. Signal failure from thermocouple. See E04: Fluid Temperature Sensor (FTS) or thermocouple disconnected, page 10. Dirty thermocouple connections. Examine connection of thermocouples to long green plug on heater control board. Unplug and re-plug thermocouple wires, cleaning off any debris. Unplug and re-plug long green connector. Thermocouple not contacting heater element. Loosen ferrule nut (N), push in thermocouple (310) so tip (T) contacts heater element (307). Holding themocouple tip (T) against heater element, tighten ferrule nut (N) 1/4 turn past tight. See page 42 for illustration. Failed heater element. See Primary Heaters, page 20. Signal failure from thermocouple. See E04: Fluid Temperature Sensor (FTS) or thermocouple disconnected, page 10. Thermocouple wired incorrectly. See E04: Fluid Temperature Sensor (FTS) or thermocouple disconnected, page 10. Power up zones one at a time and verify that temperature for each zone rises. 312066Z Troubleshooting Hose Heat System 3. Allow equipment to cool. Problems Before performing any troubleshooting procedures: Try the recommended solutions in the order given for each problem, to avoid unnecessary repairs. Also, determine that all circuit breakers, switches, and controls are properly set and wiring is correct before assuming there is a problem. 1. Relieve pressure, page 23. 2. Turn main power OFF . PROBLEM Hose heats but heats slower than usual or it does not reach temperature. CAUSE Ambient temperature is too cold. Use auxiliary hose heat system. FTS failed or not installed correctly. Check FTS, page 10. Low supply voltage. Verify line voltage. Low line voltage significantly reduces power available to hose heat system, affecting longer hose lengths. A and B setpoints too low. Increase A and B setpoints. Hose is designed to maintain temperature, not to increase it. Ambient temperature is too cold. Increase A and B setpoints to increase fluid temperature and keep it steady. Use smaller mix chamber. Decrease pressure. Wait for hose to heat to correct temperature before spraying. Flow too high. Hose does not maintain temperature while spraying. Hose temperature exceeds setpoint. SOLUTION Hose was not fully preheated. Low supply voltage. Verify line voltage. Low line voltage significantly reduces power available to hose heat system, affecting longer hose lengths. A and/or B heaters are overheating material. Check primary heaters for either a thermocouple problem or a failed element attached to thermocouple, page 10. Faulty thermocouple connections. Verify that all FTS connections are snug and that pins of connectors are clean. Examine connection of thermocouples to long green plug on heater control board. Unplug and re-plug thermocouple wires, cleaning off any debris. Unplug and re-plug long green connector on heater control board. Missing/damaged insulation around Ensure hose bundle has adequate insulaFTS, causing the hose heat to be ON tion evenly covering the entire length and constantly. connection joints. 312066Z 21 Troubleshooting PROBLEM CAUSE SOLUTION Faulty thermocouple connections. Verify that all FTS connections are snug and that pins of connectors are clean. Examine connection of thermocouples to long green plug on heater control board. Unplug and re-plug thermocouple wires, cleaning off any debris. Unplug and re-plug long green connector. FTS not installed correctly. FTS should be installed close to end of hose in same environment as gun. Verify FTS installation, page 44. Erratic hose temperature. Missing/damaged insulation around Ensure hose bundle has adequate insulaFTS, causing the hose heat to be ON tion evenly covering the entire length and constantly. connection joints. FTS failed or is not contacting correctly. Check FTS, page 44. FTS not installed correctly. FTS should be installed close to end of hose in same environment as gun. Verify FTS installation, page 44. Temperature control alarm. Check temperature display or diagnostic code, page 44. Hose does not heat. Hoses near Reactor are warm, Shorted connection or failed hose but hoses downstream are cold. heating element. With hose heat on and temperature setpoint above displayed hose zone temperature, verify voltage between connectors at each section of hose. Voltage should drop incrementally for each section of hose further from Reactor. Use safety precautions when hose heat is turned on. No hose heat. Loose hose electrical connections. Circuit breakers tripped. Hose zone not turned on. Check connections. Repair as necessary. Reset breakers (CB1 or CB2), page 32. Press A and B temperature setpoints too low. Failed temperature control board. Low hose heat. A and B temperature setpoints too low. Hose temperature setpoint too low. Flow too high. Low current; FTS not installed. Hose heat zone not turned on long enough. Loose hose electrical connections. 22 zone key. Check. Increase if necessary. Open cabinet. Check if board LED is blinking. If not, check power wiring connections to ensure board has power. If board has power and LED is not blinking, replace board, page 37. Increase A and B setpoints. Hose designed to maintain temperature, not increase temperature. Check. Increase if necessary to maintain heat. Use smaller mix chamber. Decrease pressure. Install FTS, see operation manual. Allow hose to heat up, or preheat fluid. Check connections. Repair as necessary. 312066Z Repair Repair 2. Engage gun piston safety lock. ti2409a Repairing this equipment requires access to parts that may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician connect power and ground to main power switch terminals, see operation manual. Be sure to shut off all power to the equipment before repairing. 3. Close gun fluid manifold valves A and B. Before Beginning Repair 1. Flush if necessary; see Flushing. 2. Park component A pump. ti2421a 4. Shut off feed pumps and agitator, if used. a. Press 5. Turn PRESSURE RELIEF/SPRAY valves (SA, SB) . b. Trigger gun until pump A stops. After fluid pressure drops below 700 psi (7.9 MPa, 79 bar), motor will run until component A pump is at bottom of its stroke, then shut off. c. Check ISO reservoir for component A pump. Fill wet cup on component B pump. Refer to Reactor Operation manual 312065. 3. Turn main power OFF . to PRESSURE RELIEF/CIRCULATION . Route fluid to waste containers or supply tanks. Ensure gauges drop to 0. SA SB ti10955a 4. Relieve pressure. Pressure Relief Procedure 6. Disconnect gun air line and remove gun fluid manifold. 1. Relieve pressure in gun and perform gun shutdown procedure. See gun manual. ti2554a 312066Z 23 Repair Flushing See manual 309577 for pump repair instructions. 1. Shut off Flush equipment only in a well-ventilated area. Do not spray flammable fluids. Do not turn on heaters while flushing with flammable solvents. • Flush out old fluid with new fluid, or flush out old fluid with a compatible solvent before introducing new fluid. • Use the lowest possible pressure when flushing. • All fluid components are compatible with common solvents. Use only moisture-free solvents. • To flush feed hoses, pumps, and heaters separately from heated hoses, set PRESSURE RELIEF/SPRAY valves (SA, SB) to PRESSURE RELIEF/CIRCULATION lines (N). SA A , B , and heat zones. 2. Flush pump. 3. If pumps are not parked, press . Trigger gun until pumps stop. 4. Turn main power off supply. . Disconnect power 5. Shut off both feed pumps. Close both fluid inlet ball valves (B). . Flush through bleed SB ti4147a N N TI10954a • To flush entire system, circulate through gun fluid manifold (with manifold removed from gun). • To prevent moisture from reacting with isocyanate, always leave the system dry or filled with a moisture-free plasticizer or oil. Do not use water. 6. Turn both PRESSURE RELIEF/SPRAY valves (SA, SB) to PRESSURE RELIEF. Route fluid to waste containers or supply tanks. Ensure gauges drop to 0. SA SB Pump Removal TI10956a Pump rod and connecting rod move during operation. Moving parts can cause serious injury such as pinching or amputation. Keep hands and fingers away from connecting rod during operation. 24 312066Z Repair Use drop cloth or rags to protect Reactor and surrounding areas from spills. Steps 7-9 apply to pump A. To disconnect pump B, go to steps 10 and 11. 7. Disconnect fittings at fluid inlet (C) and outlet (D, out of view). Also disconnect steel outlet tube from heater inlet. 8. Disconnect tubes (T). Remove tube fittings (U) from wet-cup. Steps 10 and 11 apply to pump B. 10. Disconnect fluid inlet (C) and outlet (D). Also disconnect steel outlet tube from heater inlet. 11. Push retaining wire clip (E) up. Push pin (F) out. Loosen locknut (G) by hitting firmly with a non-sparking hammer. Unscrew pump. E F G D 9. Loosen locknut (G) by hitting firmly with a non-sparking hammer. Unscrew pump far enough to separate and push up finger guard (P), to expose rod retaining pin. Push retaining wire clip up. Push pin out. Continue unscrewing pump. P U C T TI3765a-1 G C D TI3765a-2 312066Z 25 Repair Pump Installation 2. Continue screwing pump into housing until fluid outlet (D) is aligned with steel tube and top threads are +/- 1/16 in. (2 mm) of bearing face (N). Steps 1-5 supply to pump B. To reconnect pump A, proceed to step 6. 1. Ensure locknut (G) is screwed on pump with flat side up. Screw pump into bearing housing (M) until pin holes align. Push pin (F) in. Pull retaining wire clip (E) down. 3. Tighten locknut (G) by hitting firmly with a non-sparking hammer. 4. Reconnect fluid inlet (C) and outlet (D). 5. Go to step 13. E F M 1 3 N 2 G 2 C D 2 1 Flat side faces up. 2 Lubricate threads with ISO oil or grease. 3 Pump top threads must be nearly flush with bearing face (N). TI3765a-1 26 312066Z Repair Steps 6-12 apply to pump A only. 6. Ensure star-shaped locknut (G) is screwed on pump with flat side up. Carefully twist and extend displacement rod 2 in. (51 mm) above wet-cup. 7. Start threading pump into bearing housing (M). Place finger guard (P) over rod when it is accessible through window of bearing housing. When pin holes align, insert pin. Pull retaining wire clip down. that barbed fittings at wet-cup flush ports are accessible. 9. Connect component A outlet tube loosely at pump and at heater. Line up tube, then tighten fittings securely. 10. Tighten star-shaped locknut (G) by hitting firmly with a non-sparking hammer. 11. Apply thin film of TSL to barbed fittings. Using two hands, support tubes (T) while pushing straight onto barbed fittings. Do not let tubes kink or buckle. Secure each tube with a wire tie between two barbs. Finger guard is not used on Model E-30. 12. Reconnect fluid inlet (C). 8. Seat finger guard (P) on wet-cup. Continue threading pump into bearing housing (M) until top threads are +/- 1/16 in. (2 mm) of bearing face (N). Ensure 1 Flat side faces up. 2 Lubricate threads with ISO oil or grease. 3 Pump top threads must be nearly flush with bearing face (N). 4 Finger guard (P) not used on Model E-30. T 2 13. Purge air and prime the system. See Reactor operation manual. P 4 U M N 3 G 1 C 2 2 D TI3765a-2 312066Z 27 Repair Drive Housing Removal Installation 1. Apply grease liberally to washers (207, 208, 218), all gears, and inside drive housing (202). 1. Turn main power OFF supply. . Disconnect power 2. Relieve pressure, page 23. 3. Remove screws (38) and motor shield (9), page 50. 4. Remove screws (209) and front cover (217). Examine bearing housing (203) and connecting rod (205). If these parts need replacing, first remove the pump (206), page 28. 5. Disconnect pump inlet and outlet lines. Remove screws (213), washers (215), and bearing housing (203). CAUTION Do not drop gear cluster (204) when removing drive housing (202). Gear cluster may stay engaged in motor front end bell (R) or drive housing. 6. Remove screws (212, 219) and washers (214) and pull drive housing (202) off motor (201). 2. Install one bronze washer (208) in drive housing, then install steel washers (207, 218) as shown. 3. Install second bronze washer (208) on gear cluster (204) and insert gear cluster in drive housing. Drive housing crankshaft (S) must be in line with crankshaft at other end of motor. 4. Push drive housing (202) onto motor (201). Install screws (212, 219) and washers (214). If bearing housing (203), connecting rod (205), or pump (206) were removed, reassemble rod in housing and install pump, page 26. 5. Install bearing housing (203), screws (213), and washers (215). Pumps must be in phase (both at same position in stroke). 6. Install front cover (217) and screws (209). 7. Install motor shield (9) and screws (38). The A side drive housing includes cycle counter switch (221). If replacing this housing, remove pins (P) and switch. Reinstall pins and switch on new drive housing. Switch wires connect to J10 pins 5 and 6 on motor control board, page 34. P 221 TI3250 28 312066Z Repair 214 219 201 202 214 209 212 217 R 205 203 S R S 213 1 218 215 206B 206A 208 1 204 207 208 Crankshaft must be in line with crankshaft at other end of motor. TI3152 312066Z 29 Repair Motor Brushes 5. Loosen terminal screw (R). Pull away brush lead (L), being careful motor lead terminal (T) remains in place. Remove and discard brush (B). Brush Removal Replace brushes worn to less than 1/2 in. (13 mm). Brushes wear differently on each side of motor; check both sides. Brush Repair Kit 234037 is available. 1. Turn main power OFF supply. . Disconnect power B T Wait 5 min for stored voltage to discharge (E-30 and E-XP2 models only). R L 01227-4 6. Inspect commutator for excessive pitting, burning, or gouging. Black color on commutator is normal. Have commutator resurfaced by qualified motor repair shop if brushes wear too quickly. 7. Repeat for other side. 2. Relieve pressure, page 23. 3. Remove motor cover, screw, and washers. Remove inspection covers, screws, and gaskets from each end of motor. 4. Push in spring clip (C) to release hooks (H) from brush holder. Pull out clip and spring (S). H C S 01227-2 One brush has a wire on top for brush wear signal. Note which side of motor it is on. Unplug at spade connector provided. 30 312066Z Repair Brush Installation 4. Install spring clip (C) and push in until hooks (H) catch slots in housing. Incorrect installation may jam clip. CAUTION When installing brushes, follow steps carefully. Improper installation damages parts beyond use. H Install brush with wires on same side of motor as before. Plug spade terminal into connector. 1. Install new brush (B) so lead (L) is in long slot (D) of holder. C 01227-2 01227-6 D L B 01227-5 2. Slide terminal (L) under terminal screw (R). Make sure motor lead terminal (T) is still connected at screw. Tighten screw. Do not touch brushes, leads, springs, or brush holders while equipment is plugged in, to reduce the risk of electric shock and serious injury. CAUTION Do not run pumps dry for more than 30 sec while checking brushes, to avoid damaging pumps. B T L R 01227-4 3. Install spring (S) so it will uncoil onto brush (B), as shown. Spring will be damaged if installed backwards. 1 5. Reinstall brush inspection covers, gaskets, and screws. Reinstall motor cover, screws, washers, and drive housing/pump assemblies. 6. Test brushes with both pump pins (F) disconnected, page 30. Note direction of spring coil. Select J 1 (jog mode). Press motor to start motor. Slowly increase jog setting to J 6. Inspect brush and commutator contact area for excessive arcing. Arcs should not “trail” or circle around commutator surface. Run motor for 20-30 min at J 6 to seat brushes. B S 312066Z 1 01227 31 Repair Capacitor Test 1. Turn main power OFF Circuit Breaker Module . Disconnect power supply. 1. Turn main power OFF . Disconnect power supply. Turn circuit breakers on to test. 2. Relieve pressure, page 23. 3. Locate the large, blue capacitor in the upper right corner of the lower cabinet. 4. With a DC voltmeter, measure the voltage across the capacitor terminals to verify that the voltage has discharged to below 10 volts. 5. With an insulated handle screw driver, short across the two contacts on the end of the capacitor to complete discharging it. Hold for two seconds. NOTE: A small spark may issue from the contact point. 2. Relieve pressure, page 23. 3. Using an ohmmeter, check for continuity across circuit breaker (top to bottom). If no continuity, trip breaker, reset, and retest. If still no continuity, replace breaker as follows: a. Refer to electrical diagrams and to TABLE 2. Disconnect wires and remove bad breaker. 6. Inspect the capacitor for irregularities such as cracks, leakage, burn marks, or irregular shape. b. Install new breaker and reconnect wires. 7. Set an Ohmmeter to a range of at least 1KΩ and connect the meter leads to the capacitor with the red lead to the positive (+) terminal and the black lead to the negative (-) terminal. Table 2: Circuit Breakers, see FIG. 1 8. Observe the meter reading. It should start near 0Ω and climb up to 10KΩ, 20KΩ, etc., as the meter battery charges the capacitor. This indicates a good capacitor. 9. A reading of 0Ω (shorted) or O.L (open) indicates a bad capacitor. In this case, replace the capacitor. with the exact replacement part, item 76 on pages 55 and 56. NOTE: To reference cables and connectors, see the electrical diagrams and the parts drawings on pages 67-68. Ref. Size Component 909 50A Hose/Transformer Secondary Side 911 40A Transformer Primary 912A 25A, 40A* Heater A 912B 25A, 40A* Heater B 913 20A Motor/Pumps * Depending on model. 909 911 912A 912B 913 ti9884a FIG. 1. Circuit Breaker Module 32 312066Z Repair Electric Motor Installation Removal 1. Place motor on unit. Thread motor cables into cabinet and into bundles as before. See electrical diagrams. 1. Turn main power OFF . Disconnect power supply. 2. Fasten motor with screws. 3. Plug 3-pin connector J7 to board. 4. Plug motor power harness to connector J4 on board. 5. Install drive housing/pump assemblies, page 28. 6. Return to service. 2. Relieve pressure, page 23. 3. Remove drive housing/pump assemblies, page 28. 4. Disconnect motor cables as follows: a. Refer to electrical diagrams. Motor control board is on right side inside cabinet, see page 34. b. Unplug motor power harness from connector J4 on board. See FIG. 2, page 35. c. Unplug 3-pin connector J7 from board. d. Thread cables through top of cabinet to free motor. CAUTION Motor is heavy. Two people may be required to lift. 5. Remove screws holding motor to bracket. Lift motor off unit. 312066Z 33 Repair Motor Control Board 8. Set DIP switch (SW2) on new board. See TABLE 3 for factory settings. See FIG. 2 for location on board. Motor control board has one red LED (D11). Power must be on to check. See FIG. 2 for location. Function is: • • • • Startup: 1 blink for 60 Hz, 2 blinks for 50 Hz. Motor running: LED on. Motor not running: LED off. Diagnostic code (motor not running): LED blinks diagnostic code, pauses, then repeats (for example, E21=21 blinks, pause, 21 blinks). CAUTION Before handling board, put on a static conductive wrist strap to protect against static discharge which can damage board. Follow instructions provided with wrist strap. Table 3: DIP Switch (SW2) Settings DIP Switch Switch 1 Switch 2 Switch 3 Switch 4 Switch Position not used ON for E-20 and OFF for E-XP1 and E-30 models E-XP2 ON to enable presOFF to enable sure imbalance pressure imbalance warning alarm not used 9. Install new board in reverse order. Apply thermal heatsink compound to mating surfaces of board and heatsink. Order Part 110009 Thermal Compound. 1. Turn main power OFF . Disconnect power Table 4: Motor Control Board Connectors supply. Model E-20 and E-XP1 Model E-30 and E-XP2 Pin Description J1 N, L n/a Main motor power J8 J3 n/a Transducer B 2. Relieve pressure, page 23. J4 J1 n/a Motor output 3. Refer to electrical diagrams. Motor control board is on right side inside cabinet. J7 J6 1, 2 Motor thermal overload signal Wait 5 minutes for stored voltage to discharge (E-30 and E-XP2 models only). 3 Brush wear signal 4. Put on static conductive wrist strap. J3 J5 n/a Transducer A 5. Disconnect all cables and connectors from board. J10 J7 1-4 Not used 5, 6 Cycle switch signal 7-10 Jumper 15C866 (available in repair kit 246961) 6. Remove nuts (40) and take entire motor control assembly to workbench. 7. Remove screws and take board off heatsink. 34 J12 J12 n/a Data reporting J13 J13 n/a To display board 312066Z Repair 24G879 Motor Control, for E-20 and E-XP1 DIP Switch (SW2) Settings Model E-20 ON (UP) J3 (A) J8 (B) TI3178b-3 Model E-XP1 1 ON (UP) D11 J12 TI3178b-4 J1 SW2 J4 J7 J13 TI3153A-1 J10 24G881 Motor Control, for E-30 and E-XP2 J12 SW2 J13 DIP Switch (SW2) Settings Model E-30 J5 (A) ON (Down) TI3178b-2 J3 (B) Model E-XP2 J7 N ON (Down) 1 TI3178b-1 Apply 110009 thermal heatsink compound to mating surfaces. 1 L J1 D7 J6 TI2576A-1 FIG. 2. Motor Control Board 312066Z 35 Repair Transducers 1. Turn main power OFF . Disconnect power 4. Disconnect transducer cables at board; see FIG. 2, page 35. Reverse A and B connections and check if diagnostic code follows; see E21: No component A transducer, page 12. 5. If transducer fails test, thread cable through top of cabinet. Note path as cable must be replaced in same way. supply. 6. Install o-ring (820) on new transducer (806), FIG. 3. 7. Install transducer in manifold. Mark end of cable with tape (red=transducer A, blue=transducer B). 2. Relieve pressure, page 23. 3. Refer to electrical diagrams. Motor control board is on right side inside cabinet. 8. Route cable into cabinet and thread into bundle as before. 9. Connect transducer cable at board; see FIG. 2, page 35. 806 (A Side) 806 (B Side) 820 801 TI10957a FIG. 3. Transducers Electric Fan 4. Refer to electrical diagrams. Disconnect fan wires from fuses (F). 5. Remove fan. 1. Turn main power OFF . Disconnect power supply. 6. Install fan in reverse order. F 2. Relieve pressure, page 23. 3. Check fuses (F) at left of breaker module, FIG. 4. Replace if blown. If good, continue with step 4. ti9884a-1 FIG. 4. Fan Fuses 36 312066Z Repair Temperature Control Module A Table 5: Temperature Control Module Connections Connector H Description DATA (A) Data reporting PIN 12 11 10 B HOSE T/C P; FTS (purple) HOSE T/C R; FTS (red) HOSE T/C S; FTS (silver (unshielded bare wire)) 9 HEATER T/C B, Y; Thermocouple (yellow) SENSOR (B) 8 HEATER T/C B, R; Thermocouple (red) 7 Not used 6 HEATER T/C A, Y; Thermocouple (yellow) 5 HEATER T/C A, R; Thermocouple (red) 4, 3 OVERTEMPERATURE B; Overtemperature switch B 2, 1 OVERTEMPERATURE A; Overtemperature switch A DISPLAY (C) Display COMMUNICATION (D) Communication to power boards PROGRAM (E) Software programming BOOT (F) Software bootloader POWER/RELAY (G) Circuit board power input and contactor control output C ti9875a D E F G ti9843a1 Right Side of Control Heater Module J Table 6: Temperature Power Module Connections Connector COMMUNICATION (H) POWER (J) Description Communication to control board Power to heater ti9843a4 Bottom of Power Modules FIG. 5: Temperature Control Module Connections 312066Z 37 Repair Test SCR Circuit Replacing Temperature Control Assembly Modules 1. Test the SCR circuit in the on position: a. Make sure everything is connected, including the hose. b. Turn main power ON c. CAUTION Before handling assembly, put on a static conductive wrist strap to protect against static discharge which can damage assembly. Follow instructions provided with wrist strap. . Adjust the hose heat setpoint above the ambient hose temperature. 1. Turn main power OFF . Disconnect power supply. d. Turn on e. Hold down heat zone by pressing . to view electrical current. Hose current should ramp up to 45A. If there is no hose current, see E03: No zone current, page 10. If hose current exceeds 45A, see E02: High zone current, page 9. If hose current stays several amps below 45A, hose is too long or voltage is too low. 2. Test the SCR circuit in the off position: 2. Relieve pressure, page 23. 3. Refer to electrical diagrams; see Electrical Diagrams manual 312067. Temperature control assembly is on left side inside cabinet. 4. Remove bolts that secure transformer assembly and slide assembly to side in cabinet. 5. Put on static conductive wrist strap. a. Make sure everything is connected, including the hose. 6. Disconnect all cables and connectors from assembly; see Parts - Temperature Control, page 64. 7. Remove nuts and take entire temperature control assembly to workbench. b. Turn main power ON . 8. Replace defective module. c. Adjust the hose heat setpoint below the ambient hose temperature. d. Turn on heat zone by pressing 9. Install assembly in reverse order. . e. Using a voltmeter, carefully measure the voltage at the hose connector. You should not get a voltage reading. If you do, the SCR on the temperature control board is bad. Replace the temperature control assembly. 38 312066Z Repair 312066Z 39 Repair Primary Heaters Line Voltage Heater Element The primary heaters output their rated wattage at 230 Vac. Low line voltage will reduce power available and the heaters will not perform at full capability. 1. Turn main power OFF . Disconnect power supply. 2. Relieve pressure, page 23. 3. Wait for heaters to cool. 4. Remove heater shroud. 5. See FIG. 6. Disconnect heater element wires from heater wire connector. Test with ohmmeter. Total Heater Wattage Element Ohms 6,000 1500 30-35 7,650 2550 18-21 10,200 2550 18-21 6. To remove heater element, first remove thermocouple (310) to avoid damage, see step 7, page 42. 7. Remove heater element (307) from housing (301). Be careful not to spill any fluid left in housing. 8. Inspect element. It should be relatively smooth and shiny. If there is a crusted, burnt, ash-like material adhered to element or sheath shows pitting marks, replace element. 9. Install new heater element (307), holding mixer (309) so it does not block thermocouple port (P). 10. Reinstall thermocouple, page 42. 11. Reconnect heater element leadwires to heater wire connector. 12. Replace heater shroud. 40 312066Z Repair 313 301 310 311 308 305 303 306 1 304 304 309 313 307 315 r_247813_312066 1 Apply 110009 thermal heatsink compound. FIG. 6. Heater (7.5 kW Single Zone Heater Shown) 312066Z 41 Repair adapter must be removed, ensure that mixer (309) is out of the way when replacing the adapter. Thermocouple 8. Replace thermocouple, FIG. 7. 1. Turn main power OFF . Disconnect power supply. 2. Relieve pressure, page 23. a. Remove protective tape from thermocouple tip (T). b. Apply PTFE tape and thread sealant to male threads and tighten thermocouple housing (H) into adapter (305). c. Push in thermocouple (310) so tip (T) contacts heater element (307). 3. Wait for heaters to cool. d. Holding thermocouple (T) against heater element, tighten ferrule nut (N) 1/4 turn past tight. 4. Remove heater shroud. 5. Disconnect thermocouple wires from B on temperature control module. See TABLE 5, page 37 and FIG. 5, page 37. 6. Feed thermocouple wires out of cabinet. Note path as wires must be replaced in the same way. 7. See FIG. 7. Loosen ferrule nut (N). Remove thermocouple (310) from heater housing (301), then remove thermocouple housing (H). Do not remove the thermocouple adapter (305) unless necessary. If S 9. Route wires (S) into cabinet and thread into bundle as before. Reconnect wires to board. 10. Replace heater shroud. 11. Turn on heaters A and B simultaneously to test. Temperatures should rise at same rate. If one heater is low, loosen ferrule nut (N) and tighten thermocouple housing (H) to ensure thermocouple tip (T) contacts element (307). 1 Apply PTFE tape and thread sealant. 2 Apply 110009 thermal heatsink compound. 310 N H 1 301 307 2 308 35 T 309 ti7924a FIG. 7. Thermocouple 42 312066Z Repair Overtemperature Switch 1. Turn main power OFF 4. Using an ohmmeter, check between the two terminals of the connector (D). There should be continuity. . Disconnect power supply. 2. Relieve pressure, page 23. 5. If hose fails test, retest at each length of hose, including whip hose, until failure is isolated. Check FTS Cables 1. Turn main power OFF . Disconnect power supply. 2. Relieve pressure, page 23. 3. Wait for heaters to cool. 3. Disconnect FTS cable (F) at Reactor, FIG. 8. 4. Remove heater shroud. 5. Disconnect one leadwire from overtemperature switch (308), FIG. 7. Test across switch with ohmmeter. Resistance must be approximately 0 ohms. D F 6. If switch fails test, remove wires and screws. Discard failed switch. Apply thermal compound 110009, install new switch in same location on housing (301), and secure with screws (311). Reconnect wires. TI10964a FIG. 8. Heated Hose If wires need replacement, disconnect from temperature control board. See TABLE 5, page 37 and FIG. 5, page 37. Heated Hose Refer to the heated hose manual 309572 for hose replacement parts. Check Hose Connectors 1. Turn main power OFF 4. Test with ohmmeter between pins of cable connector. Pins Result 1 to 2 approximately 35 ohms per 50 ft (15.2 m) of hose, plus approximately 10 ohms for FTS 1 to 3 infinity 5. If cable fails test, retest at FTS, page 44. . Disconnect power supply. 2. Relieve pressure, page 23. Whip hose must be connected. 3. Disconnect hose connector (D) at Reactor, FIG. 8. 312066Z 43 Repair Fluid Temperature Sensor (FTS) 4. If FTS fails any test, replace FTS. Test/Removal 5. Disconnect air hoses (C, L), and electrical connectors (D). 1. Turn main power OFF 6. Disconnect FTS from whip hose (W) and fluid hoses (A, B). . Disconnect power supply. 7. Remove ground wire (K) from ground screw on underside of FTS. 2. Relieve pressure, page 23. 8. Remove FTS probe (H) from component A (ISO) side of hose. 3. Remove tape and protective covering from FTS (21), FIG. 8. Disconnect hose cable (F). Test with ohmmeter between pins of cable connector. Pins Result 1 to 2 approximately 10 ohms 1 to 3 infinity 3 to FTS groundscrew 0 ohms 1 to FTS component A fitting (ISO) infinity Installation The Fluid Temperature Sensor (FTS) is supplied. Install FTS between main hose and whip hose. See Heated Hose manual 309572 for instructions. B D K W A B ISO A H C L WL E ti17029b FIG. 9: Fluid Temperature Sensor and Heated Hoses 44 312066Z Repair Transformer Primary Check 1. Turn main power OFF 3. To verify transformer voltage, turn on hose zone. Measure voltage from 18CB-2 to POD-HOSE-P15-2; see Reactor Electrical Diagrams manual 312067. . 2. Locate the two smaller (10 AWG) wires coming out of transformer. Trace these wires back to contactor and circuit breaker (911). Use an ohmmeter to test for continuity between two wires; there should be continuity. Model Secondary Voltage 310 ft. 90 Vac* 210 ft. 62 Vac* * For 230 Vac line voltage. Transformer Secondary Check Replace Transformer 1. Turn main power OFF . Use this procedure to replace transformer. 2. Locate the two larger (6 AWG) wires coming out of transformer. Trace these wires back to large green connector under hose control module and circuit breaker (909). Use an ohmmeter to test for continuity between two wires; there should be continuity. 1. Turn main power OFF . Disconnect power supply. If you are not sure which wire in green plug under hose module connects to transformer, test both wires. One wire should have continuity with the other transformer wire in breaker (909) and the other wire should not. 2. Open Reactor cabinet. 3. Remove bolts holding transformer to cabinet floor. Slide transformer forward. 4. Disconnect the transformer wires; see Reactor Electrical Diagrams manual 312067. 5. Remove transformer from cabinet. 909 911 ti9884a 6. Install new transformer in reverse order. FIG. 10: Circuit Breaker Module 312066Z 45 Repair Display Module between cable bushing and cover (504) with screws (512). Temperature and Pressure Displays CAUTION Before handling board, put on a static conductive wrist strap to protect against static discharge which can damage board. Follow instructions provided with wrist strap. 1. Turn main power OFF Red Stop Button CAUTION Before handling board, put on a static conductive wrist strap to protect against static discharge which can damage board. Follow instructions provided with wrist strap. . Disconnect power supply. 1. Turn main power OFF . Disconnect power supply. 2. Relieve pressure, page 23. 3. Refer to electrical diagrams. 4. Put on static conductive wrist strap. 2. Relieve pressure, page 23. 3. Refer to electrical diagrams. 4. Put on static conductive wrist strap. 5. Disconnect main display cable (20) at lower left corner of display module; see FIG. 11. 6. Remove screws (509, 510) and cover (504); see FIG. 11. If replacing both displays, label temperature display cables TEMP and pressure display cables PUMP before disconnecting. 5. Remove screws (509, 510) and cover (504), FIG. 11. 6. Disconnect button cable connectors (506) from back of temperature display (501) and pressure display (502). 7. Remove red stop button (506). 8. Reassemble in reverse order. Be sure display cable ground wire (G) is secured between cable bushing and cover (504) with screws (512). 7. Disconnect cable connectors (506 and 511) from back of temperature display (501) or pressure display (502); see FIG. 11. 8. Disconnect ribbon cable(s) (R) from back of display; see FIG. 11. 9. Remove nuts (508) and plate (505). 10. Disassemble display, see detail in FIG. 11. 11. Replace board (501a or 502a) or membrane switch (501b or 502b) as necessary. 12. Reassemble in reverse order, see FIG. 11. Apply medium strength thread sealant where shown. Be sure display cable ground wire (G) is secured 46 312066Z Repair 1 Apply medium strength thread sealant. G 511 511 503 502 504 510 507 1 506 512 20 1 501 508 505 ti2574a 506 Detail of Membrane Switches and Display Boards Temperature Display 1 502c Pressure Display 502a 502b 501c 1 501a R R 501b ti3172a FIG. 11. Display Module 312066Z 47 Repair Inlet Fluid Strainer Screen A* B The inlet strainer at each proportioning pump filters out solid matter that can plug the inlet check valves. Inspect the screens daily as part of the startup routine, and clean as required. Isocyanate can crystallize from moisture contamination or from freezing. If the chemicals used are clean and proper storage, transfer, and operating procedures are followed, there should be minimal contamination of the A-side screen. Clean the A-side screen only during daily startup. This minimizes moisture contamination by immediately flushing out any isocyanate residue at the start of dispensing operations. C D TI10974a FIG. 12. Y Strainer Components * Fluid filter screen (59g) replacements: Part 180199 255082 255083 Description 20 mesh (standard); 1 pack 80 mesh (optional); 2 pack 80 mesh (optional); 10 pack Pump Lubrication System 1. Close the material supply valve at the pump inlet to prevent material from being pumped while the strainer plug (C) is removed. 2. Place a container under the strainer base to catch drain off when removing the strainer plug. Check the condition of the ISO pump lubricant daily. Change the lubricant if it becomes a gel, its color darkens, or it becomes diluted with isocyanate. 3. Remove the screen (A) from the strainer manifold. Thoroughly flush the screen with gun cleaner and shake it dry. Inspect the screen for blockage. No more than 25% of the mesh should be restricted. If more than 25% is blocked, replace the screen. Inspect the strainer gasket (B) and replace as required. Gel formation is due to moisture absorption by the pump lubricant. The interval between changes depends on the environment in which the equipment is operating. The pump lubrication system minimizes exposure to moisture, but some contamination is still possible. 4. Ensure the pipe plug (D) is securely screwed into the strainer plug (C). Install the strainer plug with the screen (A) and gasket (B) in place and tighten. Do not overtighten. Let the gasket make the seal. Lubricant discoloration is due to continual seepage of small amounts of isocyanate past the pump packings during operation. If the packings are operating properly, lubricant replacement due to discoloration should not be necessary more often than every 3 or 4 weeks. 5. Open the material supply valve, ensure that there are no leaks, and wipe the equipment clean. To change pump lubricant: 6. Proceed with operation. 1. Relieve pressure, page 23. 2. Lift the lubricant reservoir (LR) out of the bracket (RB) and remove the container from the cap. Holding the cap over a suitable container, remove the inlet check valve and allow the lubricant to drain. Reattach the inlet check valve to the inlet hose. See FIG. 13. 48 312066Z Repair 3. Drain the reservoir and flush it with clean lubricant. 4. When the reservoir is flushed clean, fill with fresh lubricant. ST RT 5. Thread the reservoir onto the cap assembly and place it into the bracket. RB 6. The lubrication system is ready for operation. No priming is required. LR TI10970a RT ST LR TI10969a FIG. 13. Pump Lubrication System 312066Z 49 Parts Parts Reactor Assembly (Model E-XP1 Shown) 4 1 120 40 41 121 57 44 45 9 2 48 15 38 59 17 16 58 3 14 10 72 TI10960a TI10953a 7 51 90 34 88 16 41, 102 21 60 41 122 110 Strut Channel Style Support Rail 97 113, 119 72 TI10977a 109, 111, 112 96 95 Slotted U-Channel Style Support Rail 115 41 65f 65a 65e 122 65d 50 TI10961a TI18608a 65b, 65c 312066Z Parts Left Side of Cabinet 42 28 5 61, 62 123 8 TI9835a 41 76 Right Side of Cabinet 77 33 31, 42 36 (400V models only) 27 39, 52, 71, 73 6 29, 42 TI10968a 312066Z 51 Parts Detail, Fluid Manifold Area 14 7, see page 66 89 16 90 78 12 817 (Ref) 90 106 127 107 19 TI10962a 41 Detail, Cabinet Area 41 mounting base (from motor) 38 35 57 87 25 13 61 24 26 TI10978a 41 52 312066Z Parts Parts Used on All Models See pages 54 through 56 for parts that vary by model. Ref. 1 2 3 4 5 6 7 8 9 10 11† 12 13 14 Part 245974 247823 246976 261669 15B456 115834 15 16 17 18† 247787 19† 15B380 20 21 22 23 24 25 26 27 28 29 31 33★ 34★ 35 36 38 15B383 39 40 41 42 44 45 48▲ 51▲ 52 53 57 58 59 60▲ 61 62 65 65a 65b 65c† 65d 116773 C38163 15B361 15B510 15B360 255047 116149 117666 123969 123967 117723 115492 117623 113796 115942 15K817 189930 189285 15B593 15B775 247524 256732 15G280 113505 112776 101078 180199 C20487 312066Z Description FRAME; page 62 HEATER; pages 60 and 61 MODULE, proportioner; page 58 DISPLAY; page 63 CONTROL, temperature; page 64 CONTROL, motor; page 65 MANIFOLD, fluid; page 66 TRANSFORMER; pages 54-56 SHIELD; page pages 54-56 DOOR, cabinet SENSOR, fluid temperature GASKET, manifold FAN TUBE, heater component A; pages 54-56 TUBE, pump, component A; pages 54-56 TUBE, heater component B; pages 54-56 TUBE, pump, component B; pages 54-56 CABLE, overtemperature; see electrical diagrams CABLE, hose control; see electrical diagrams CABLE, display CONNECTOR, tube; pages 54-56 CONNECTOR, plug WASHER, lock, external tooth BOOT, wire feed through PLATE, cover, wire GASKET, fan STRAIN RELIEF MODULE, breaker; pages 54-56 SPACER TERMINAL, ground SWITCH, disconnect SWITCH, main power SCREW, machine; 6-32 x 2 in. (51 mm) SWITCH, added pole; 380V; page 54 SCREW, machine; 8-32 x 0.345 in. (9 mm) FILTER; 230V; page 54 NUT, cap; 3/8-16 SCREW, flanged, hex hd; 1/4-20 x 3/4 in. (19 mm) NUT, hex flange; 1/4-20 LABEL, diagnostic codes LABEL, caution LABEL, caution LABEL, warning; pages 54-56 CABLE. harness, filter; pages 54-56 SHIELD, membrane switch; pack of 10 COVER, wire access COVER, heater, back COVER, heater, front LABEL, warning NUT, hex, keps; 10-24 WASHER, plain; no. 10 KIT, fluid inlet FITTING, swivel, elbow Y-STRAINER ELEMENT, 20 mesh NIPPLE, 3/4 npt Qty 1 * * 1 1 * 1 * * 1 1 1 1 * * * * 1 1 1 * 1 1 1 1 1 1 * 8 1 1 1 4 * 13 * 4 15 15 1 3 3 * * 1 2 1 1 1 6 2 1 2 2 2 2 Ref. 65e 65f Part 109077 118459 66 66a† 67 68 69 101078 180199 109077 C20487 157785 71 72◆ 73 76 77 86 87 88 89 90 15B807 186494 205447 15M338 95◆ 96◆ 97◆ 102 106 107 109 117502 117677 246928 110 054826 111 112 113 115 117 119 120▲ 121 122 123 124 125 118433 118432 116746 15C568 206995 191892 171001 247782 247854 114331 Description Qty VALVE, ball; 3/4 npt (fbe) 2 FITTING, union, swivel; 3/4-14 npt(m) x 2 3/4-14 npt(f) Y-STRAINER; includes 66a 2 ELEMENT, 20 mesh 1 VALVE, ball; 3/4 npt (fbe) 2 NIPPLE; 3/4 npt 2 UNION, swivel; 3/4 npt(m) x 3/4 2 npsm(f) SCREW, machine; pages 54-56 * BRACKET. heater; pages 54-56 * WASHER, lock; pages 54-56 * CAPACITOR; pages 54-56 * BRACKET; pages 54-56 * CABLE, overtemperature, jumper; * pages 54-56 SHIELD, fan 1 CLIP, spring 6 COUPLING, hose 2 TUBE, low pressure; 1/4 in. (6 mm) ID; 1 3/8 in. (16 mm) OD; 4 ft (1.2 m); PTFE BOLT; hex hd; pages 54-56 * LOCKWASHER; 3/8; pages 54-56 * NUT, channel; pages 54-56 * STRAP, motor; pages 54-56 * REDUCER; #5 x #8 JIC 1 REDUCER; #6 x #10 JIC 1 RESERVOIR; includes 110-119; see 1 309911 TUBE; PTFE; 1/4 in. (6 mm) ID; 2 2 ft (0.6 m) VALVE, check 1 VALVE, check 1 FITTING, barbed 2 BRACKET, reservoir 1 THROAT SEAL LIQUID; 1 qt (1 liter) 1 ELBOW; 1/8 npt (m x f) 2 LABEL, warning 1 LABEL; pages 54-56 * INSULATOR, heat; pages 54-56 * SPACER 4 COVER, connector, module 1 SCREW, machine; 6-32 x 0.375 in. (9.5 2 mm) ▲ Replacement Danger and Warning labels, tags, and cards are available at no cost. * See quantity on referenced pages. † Not shown. ★ Required for all A-D series models. Included in Knob Repair Kit 258920 (purchase separately). ◆ Not required for slotted U-Channel style heater support rails. 53 Parts Parts that Vary by Model Use the following tables on this and the next two pages to find parts that vary by model. Find the reference number and of part in left column and Reactor model in top row. Intersection is correct part number. See page 53 for parts common to all models. Reactor Models Qty Ref. Description 259024 259025 259026 259028 259029 259030 259031 259032 259033 259034 259035 259036 E-XP1 E-20 E-30 E-XP2 E-XP1 E-20 E-30 E-XP2 E-XP1 E-20 E-30 E-XP2 2 HEATER; pages 247507 247506 247507 247509 247507 247506 247507 247509 247507 247506 247507 247509 60 and 61 (qty: 2) (qty: 2) (qty: 2) 1 3 MODULE, proportioner; page 58 245956 245956 245957 245959 245956 245956 245957 245959 245956 245956 245957 245959 1 6 CONTROL, motor; page 65 24G879 24G879 24G881 24G881 24G879 24G879 24G881 24G881 24G879 24G879 24G881 24G881 1 8 TRANSFORMER; 247840 247840 247812 247812 247840 247840 247812 247812 247840 247840 247812 247812 1 9 SHIELD 276878 276878 276879 276879 276878 276878 276879 276879 276878 276878 276879 276879 1 14 TUBE, heater, component A 247920 247920 247920 247915 247920 247920 247920 247915 247920 247920 247920 247915 1 15 TUBE, pump, component A 247912 247912 247919 247914 247912 247912 247919 247914 247912 247912 247919 247914 1 16 TUBE, heater, component B 247918 247918 247918 247917 247918 247918 247918 247917 247918 247918 247918 247917 1 17 TUBE, pump, component B 247913 247913 247921 247916 247913 247913 247921 247916 247913 247913 247921 247916 1 21 CONNECTOR, tube 121310 121310 121311 121311 121310 121310 121311 121311 121310 121310 121311 121311 2 28 MODULE, breaker; page 67 36 SWITCH, added pole; 380V 39 FILTER; 230V 54 C C F F B B E E A A D D 123968 123968 123968 123968 117667 117667 117667 117667 1 1 117667 117667 312066Z 1 Parts Reactor Models Qty Ref. Description 259024 259025 259026 259028 259029 259030 259031 259032 259033 259034 259035 259036 E-XP1 E-20 E-30 E-XP2 E-XP1 E-20 E-30 E-XP2 E-XP1 E-20 E-30 E-XP2 51▲ LABEL, warning 198278 198278 198278 198278 198278 198278 1 52 CABLE, harness, filter 15B385 15B385 15B385 15B385 15B385 15B385 1 65 KIT, fluid inlet 234366 234366 234367 234366 234366 234366 234367 234366 234366 234366 234367 234366 1 65a ELBOW, swivel; 3/4 npt(m) x 1” 160327 160327 118463 160327 160327 160327 118463 160327 160327 160327 118463 160327 npt(f) 2 71 2 SCREW, machine 72◆ BRACKET, heater --- --- 247523 247523 247523 BRACKET, heater --- --- 247523 247523 247523 --- --- 247523 247523 247523 2 247523 247523 247523 4 73 WASHER, lock 103181 103181 103181 103181 103181 103181 2 76 CAPACITOR 244733 244733 244733 244733 244733 244733 1 77 BRACKET 197999 197999 197999 197999 197999 197999 1 86 CABLE, overtemperature, jumper 95◆ BOLT; hex hd; 3/8-16 15H187 15H187 15H187 15H187 15H187 15H187 15H187 15H187 15H187 1 100469 100469 100469 100469 100469 100469 100469 100469 100469 2 BOLT; hex hd; 3/8-16 100469 96◆ LOCKWASHER; 100133 100133 100133 3/8 LOCKWASHER; 3/8 97◆ NUT, channel NUT, channel 100469 100133 100133 100133 100133 118446 118446 118446 100133 100133 100133 100133 118446 118446 118446 2 100133 118446 118446 118446 118446 4 4 2 118446 4 102 STRAP, motor 15B107 15B107 15B108 15B108 15B107 15B107 15B108 15B108 15B107 15B107 15B108 15B108 1 121 LABEL 15M504 15M500 15M499 15M501 15M504 15M500 15M499 15M501 15M504 15M500 15M499 15M501 1 122 INSULATOR 167002 167002 167002 167002 167002 167002 167002 167002 167002 167002 167002 167002 (qty: 4) (qty: 4) (qty: 4) 2 312066Z 118446 100469 55 Parts Parts that Vary by Model (continued) Reactor Models Reactor Models Ref. Description 259057 259058 259059 E-30 E-30 E-30 w/15.3kW w/15.3kW w/15.3kW Qty Ref. Description HEATER; pages 247509 60 and 61 247509 247509 2 3 MODULE, proportioner; page 58 245957 245957 245957 1 6 CONTROL, motor; page 65 24G881 24G881 24G881 1 8 TRANSFORMER; 247812 247812 247812 1 9 SHIELD 276879 276879 276879 1 14 TUBE, heater, component A 247915 247915 247915 1 15 TUBE, pump, component A 247914 247914 247914 1 16 TUBE, heater, component B 247917 247917 247917 1 17 TUBE, pump, component B 247916 247916 247916 1 21 CONNECTOR, tube 121311 121311 121311 2 28 MODULE, breaker; page 67 36 SWITCH, added pole; 380V 39 FILTER; 230V F D E 123968 1 117667 117667 117667 1 198278 198278 198278 1 15B385 15B385 1 65 KIT, fluid inlet 234367 234367 234367 1 118463 118463 118463 2 SCREW, machine --- --- --- 118446 118446 4 102 STRAP, motor 15B108 15B108 15B108 1 121 LABEL 15M499 15M499 15M499 1 122 Insulator 167002 167002 167002 4 ▲ Replacement Danger and Warning labels, tags, and cards are available at no cost. ◆ Not required for slotted U-Channel style heater support rails. 2 72◆ BRACKET, heater 247523 247523 247523 4 73 WASHER, lock 103181 103181 103181 2 76 CAPACITOR 244733 244733 244733 1 77 BRACKET 197999 197999 197999 1 100469 100469 100469 4 LOCKWASHER; 100133 3/8 100133 100133 4 95◆ BOLT; hex hd; 3/8-16 118446 1 CABLE, harness, 15B385 filter 71 NUT, channel --- Not for sale. 52 65a ELBOW, swivel; 3/4 npt(m) x 1” npt(f) Qty 97◆ NUT, channel 2 51▲ LABEL, warning 259057 259058 259059 E-30 E-30 E-30 w/15.3kW w/15.3kW w/15.3kW 96◆ LOCKWASHER; 3/8 56 312066Z Parts 312066Z 57 Parts Sub Assemblies Proportioner Module 245956 Module for E-20 and EXP-1 219 214 201 245957 Module for E-30 202 245959 Module for EXP-2 226 205 217 209 203 212 214 213 1 215 218 *208 225 216 **210 216 211 208 204 *207 206B 1 210** 211 224 206A TI2511a 1 Flat side faces up. Detail of Cycle Counter Switch 220 221 TI3250a 58 312066Z Parts Proportioner Assembly 245956 Module, for E-20 and E-XP1 Ref. 221 223 245957 Module, for E-30 245959 Module, for E-XP2 102962 224 225 226 Ref. 201 202 203 204 Part 24V618 24V500 245968 245969 240523 241015 245927 244264 244265 205 241008 241279 206A 246830 246831 246832 206B 245970 245971 245972 207* 208* 209 114699 114672 114418 114818 210** 176817 183169 211 176818 183210 212 107218 114686 213 107210 114666 214 215 216 217 218 219 105510 104008 106115 192723 193031 193394 179899 241308 116191 116192 100644 101864 220 116618 312066Z Description Qty MOTOR; 245956 1 MOTOR; 245957, 245959 1 HOUSING, drive; 245956 2 HOUSING, drive; 245957, 245959 2 HOUSING, bearing; 245956 2 HOUSING, bearing; 245959 2 HOUSING, bearing; 245957 2 GEAR; includes items 207, 208; 2 245956 GEAR; includes items 207, 208; 2 245957, 245959 ROD, connecting; includes item 210; 2 245956 ROD, connecting; includes item 210; 2 245957, 245959 PUMP, displacement, component A; 1 245956; see 309577 PUMP, displacement, component A; 1 245959; see 309577 PUMP, displacement, component A; 1 245957; see 309577 PUMP, displacement, component B; 1 245956; see 309577 PUMP, displacement, component B; 1 245959; see 309577 PUMP, displacement, component B; 1 245957; see 309577 WASHER, thrust; steel 2 WASHER, thrust; bronze 4 SCREW, self-tapping; 8-32 x 1 in. (25 8 mm); 245956 SCREW, self-tapping; 8-32 x 1-1/4 in. 8 (31 mm); 245957, 245959 CLIP, wire; 245956 2 CLIP, wire; 245957, 245959 2 PIN; 245956 2 PIN; 245957, 245959 2 SCREW, cap, socket-hd; 1/4-20 x 2-3/4 4 in. (70 mm); 245956 SCREW, cap, socket-hd; 5/16-18 x 4 3-1/4 in. (83 mm); 245957, 245959 SCREW, cap, socket-hd; 3/8-16 x 1-1/2 8 in. (38 mm); 245956 SCREW, cap, socket-hd; 3/8-16 x 2-1/4 8 in. (57 mm); 245957, 245959 WASHER, lock; 1/4; 245956 12 WASHER, lock; 5/16; 245957, 245959 12 WASHER, lock; 3/8 size 8 NUT, retaining; 245956 2 NUT, retaining; 245959 2 NUT, retaining; 245957 2 COVER; 245956 2 COVER; 245957, 245959 2 WASHER, thrust; 245956 2 WASHER, thrust; 245957, 245959 2 SCREW, cap, socket-hd; 1/4-20 x 3/4 4 in. (19 mm); 245956 SCREW, cap, socket-hd; 5/16-18 x 1 in. 4 (25 mm); 245957, 245959 MAGNET 1 Part 117770 100643 * 104765 15C587 15C588 15M507 15M508 Description Qty SWITCH, cycle counter 1 SCREW, cap, socket-hd; 1/4-20 x 1 in. 4 (25 mm); 245956 SCREW, cap, socket-hd; 5/16-18 x 4 1-1/4 in. (31 mm); 245957, 245959 PLUG 2 GUARD, finger; 245956 1 GUARD, finger; 245959 1 LABEL; 245956 1 LABEL; 245957, 245959 1 Parts included in Gear Kit 244264 (245956) or 244265 (245957, 245959). ** Parts included in Connecting Rod Kit 241008 (245956) or 241279 (245957, 245959). 59 Parts Fluid Heaters 247506, 6.0 kW Fluid Heaters 247507, 10.2 kW Fluid Heaters 310 313 303 305 304 306 308 1 311 314 301 309 r_247507_312408 307 1 Apply 110009 thermal heatsink compound. 315 Ref 301 Part Description HOUSING, heater Qty. 1 Ref Part Description Qty. 2 310 117484 SENSOR 311 100518 SCREW, machine, pan hd 2 303 121309 ADAPTER 4 313 15H305 PLUG, hollow 4 304 15H304 PLUG 2 314 247520 DISC, rupture 2 305 15H306 ADAPTER, thermocouple 2 315 124132 O-RINGS 4 306 120336 O-RING; fluoroelastomer 2 307 HEATER, immersion 4 16A110 2550W; 10.2kW heater only 16A112 1500 W; 6.0 kW heater only 308 15B137 SWITCH, overtemperature 1 309 15B135 MIXER, immersion heater 4 60 312066Z Parts 7.65 kW Single Zone Fluid Heater (Two Per Machine) Part 247509 301 313 310 311 308 305 303 306 304 1 314 304 309 313 307 r_247813_312066 315 1 Ref. 301 303 304 305 306 307 308 309 Part 121309 15H304 15H306 120336 16A110 15B137 15B135 312066Z Description HOUSING, heater ADAPTER PLUG ADAPTER, thermocouple O-RING; fluoroelastomer HEATER, immersion; 2550 W SWITCH, overtemperature MIXER, immersion heater Qty 1 2 3 1 1 3 1 3 Apply 110009 thermal heatsink compound. Ref. 310 311 313 314 315 Part 117484 100518 15H305 247520 124132 Description SENSOR SCREW, machine, pan hd PLUG, hollow DISC, rupture; not shown O-RING Qty 1 2 5 1 3 61 Parts Reactor Frame 405 401 406 404 402 404 403 TI2513a 407 Ref. 401 402 403 404 405 406 407 62 Part 116478 101242 116477 112125 116411 154636 Description FRAME WHEEL RING, retaining WASHER, flat; nylon PLUG SPRING WASHER, flat Qty 1 2 2 4 2 2 4 312066Z Parts Display 511 502 511 503 504 507 510 506 512 20 (Ref) 508 501 ti2574a 505 506 502a 502c 502b 501c 501a 501b Ref. 501 501a 501b 501c 502 502a 502b 502c 503 504 Part Description 24G884 DISPLAY, pressure; includes 501a-501c 24G882 .BOARD, circuit 246479 .SWITCH, membrane 112324 .SCREW 24G883 DISPLAY, temperature; includes 502a-502c 24G882 .BOARD, circuit 246479 .SWITCH, membrane 112324 .SCREW 15B293 GASKET 15B292 COVER 312066Z Qty. 1 1 1 4 1 1 1 4 1 1 Ref. 505 506 507 508 510 511 512 Part 15B291 246287 117499 117523 --- ti3172a Description PLATE HARNESS, wire, red stop button HANDLE NUT, cap; 10-24 SCREW, machine, pan-hd; M5 x 0.8; 16 mm 15B386 CABLE, display 195853 SCREW, machine; M2.5 x 6 Qty. 1 1 2 8 4 1 2 --- Not for sale. 63 Parts Temperature Control 602 605 To B Heater Module 604 606 To A Heater Module 601 To Hose Heater Module 604 604 604 603 603 TI9843a 603 Ref. 601 602 603 604 605 606 64 Part 247772 247827 247828 115942 247801 247825 Description Qty. 1 PANEL, module mounting 1 HOUSING, control module 3 HOUSING, heater module 4 NUT, hex 1 CABLE, communication 1 KIT, cover, connector with screws 312066Z Parts Motor Control 24G879 Motor Control for E-20 and EXP-1 1 703 1 Apply 110009 thermal heatsink compound to mating surfaces. 2 Motor harness (609) plugs in here. 701 TI3153a 702 24G881 Motor Control for E-30 and EXP-2 701 704 707 703 705 1 2 702 24G879 Motor Control for E-20 and EXP-1 Ref. Part Description 701 702 703 15B297 24G878 107156 HEAT SINK BOARD, motor control SCREW, machine; 6-32 TI2576a 24G881 Motor Control for E-30 and EXP-2 Qty. 1 1 7 Ref. Part Description 701 702 703 16F745 ----- 704 705 707 709 117526 117683 15C007 15B408 HEAT SINK BOARD, motor control SCREW, machine; 6-32 x 3/8 in. (10 mm) SPACER SCREW, 6-32 x 1-1/2 in. (38 mm) INDUCTOR CABLE, harness, motor Qty. 1 1 6 3 2 1 1 --- Not for sale. 312066Z 65 Parts Fluid Manifold 1 Torque to 355-395 in-lb (40.1-44.6 N•m). 2 Apply sealant (113500) to threads. 3 Valve must be closed with handle position as shown on drawing. ** Apply PTFE tape or thread sealant to tapered threads. 2 808 806 3 805 1 818 802 3 803 2 802a 802b 814 815 816 804 807 801 814 812 813 Ref. Part 801 247837 802† 247824 802a† 158674 802b† 247779 803 102814 804 162453 805 24K999 806 247788 807 247789 808† 112309 812 117556 813 117557 66 3 Description Qty. 1 MANIFOLD, fluid 2 VALVE, drain cartridge 1 . O-RING 1 . SEAL, seat, valve 2 GAUGE, pressure, fluid 2 FITTING, 1/4 npsm x 1/4 npt 2 TRANSDUCER, pressure, control 1 HANDLE, red 1 HANDLE, blue 2 NUT, hex, jam 1 NIPPLE, #8 JIC x 1/2 npt 1 NIPPLE, #10 JIC x 1/2 npt 817 Ref. 814 815 816 817▲ 818† TI10959a Part 121312 100840 111457 189285 150829 Description Qty. 2 ELBOW, 90 degrees 2 ELBOW, street; 1/4 npsm x 1/4 npt 2 O-RING, PTFE 1 LABEL, caution 2 SPRING, compression ▲ Replacement Warning labels, signs, tags, and cards are available at no cost. † Included in the following complete valve kits*: ISO Valve Kit (left/red handle) 255149. Resin Valve Kit (right/blue handle) 255150. Valve Set Kit (both handles and grease gun) 255148. * Complete valve kits also include thread sealant. (Purchase kits separately). 312066Z Parts Circuit Breaker Modules A - 230V, 3 Phase Circuit Breaker Modules (E-20, EXP-1) For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 910 920 914 905 906 917 911 915 903, 904 908 168BR 238CR 902 916 178CB 187CB 197CB 901 172CB 913 918 919 912 909 922 907 B - 400V, 3 Phase Circuit Breaker Modules (E-20, E-XP1) For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 920 910 905 906 917 911 903, 904 908 902 901 238CR 916 187CB 178CB 172CB 913 918 909 907 312066Z 197CB 912 919 922 67 Parts C - 230V, 1 Phase Circuit Breaker Modules (E-20, EXP-1) 910 920 For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 903, 904 905 906 914 917 911 915 908 902 238CR 168BR 916 901 197CB 187CB 178CB 172CB 913 918 909 912 907 919 922 D - 230V, 3 Phase Circuit Breaker Modules (E-30, EXP-2) For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 910 920 905 906 914 917 911 915 903, 904 908 "2 #2 902 916 #" #" 901 #" 913 918 909 907 68 #" 912 919 922 312066Z Parts E - 400V, 3 Phase Circuit Breaker Modules (E-30, E-XP2) For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 910 920 905 906 917 911 903, 904 908 #2 902 916 #" #" #" 901 #" 913 918 919 912 909 907 922 F - 230V, 1 Phase Circuit Breaker Modules (E-30, EXP-2) For wiring and cable connections, refer to electrical diagrams manual 312067, supplied. See page 70 for parts. 910 920 905 906 914 917 911 915 903, 904 908 902 #2 916 "2 901 #" #" #" 913 918 909 907 312066Z #" 912 919 922 69 Parts Circuit Breaker Modules Parts List Breaker Modules E-20 and EXP-1 Models E-30 and EXP-2 Models Ref. Description A 230V, 3 phase B 400V, 3 phase C 230V, 1 phase D 230V, 3 phase E 400V, 3 phase F 230V, 1 phase Qty 901 RAIL, mounting 255028 255028 255028 255028 255028 255028 1 902 CLAMP, block, end 255045 255045 255045 255045 255045 255045 1 903 HOLDER, fuse terminal, block 255043 255043 255043 255043 255043 255043 2 904 FUSE 255023 255023 255023 255023 255023 255023 2 905 TERMINAL, block 255042 255042 255042 255042 255042 255042 4 --- --- --- --- --- --- 1 907 BRIDGE, plug in, jumper 255044 255044 255044 255044 255044 255044 2 908 BLOCK, terminal ground 255046 255046 255046 255046 255046 255046 1 909 BREAKER, 1 pole, 50A 255026 255026 255026 255026 255026 255026 1 910 CONTACTOR, relay, 65A 255022 255022 255022 255022 255022 255022 1 911 BREAKER, 2 phase, 40A 247768 247768 247768 247768 247768 247768 1 912 BREAKER, 2 phase, 25A 255050 255050 255050 255050 255050 255050 2 BREAKER, 2 phase, 40A 247768 247768 247768 247768 247768 247768 2 913 BREAKER, 2 phase, 20A 255049 255049 255049 255049 255049 255049 1 914 CONNECTOR, power lug 117679 906 TERMINAL, end cover 117679 117679 CONNECTOR, power lug 915 BAR, power buss, 3 phase 3 117805 117679 117805 1 117678 BAR, power buss, 1 phase 2 117678 1 916 CABLE, harness lower 247802 247802 247802 247802 247802 247802 1 917 CABLE, harness upper 247805 247806 247804 247805 247806 247804 1 918 CONNECTOR, 2 pin large 255027 255027 255027 255027 255027 255027 3 919 CONNECTOR, 3 pin 247522 247522 247522 247567 247567 247567 1 920 CONNECTOR, 4 pin 255031 255031 255031 255031 255031 255031 1 922 CABLE, harness 247791 247791 247791 247791 247791 247791 1 --- Not for sale. 70 312066Z 248669 Conversion Kit 248669 Conversion Kit Convert and phase E-XP2 to and E-30 with 15.3 kW of heat by changing displacement pumps, bearings, and changing the Motor Control DIP settings to that of an E-30. For removal and installation of displacement pumps and bearings, see Pump Removal (page 24) and Pump Installation (page 26). For changing Motor Control DIP settings, see Motor Control Board, page 34. Ref. 65 Part Description Qty. 118463 ELBOW, swivel; 3/4 npt(m) x 1 in. 2 npt(f) 303 245927 HOUSING, bearing 2 306A 246832 PUMP, displacement, component 1 A; see 309557 306B 245972 PUMP, displacement, component 1 B; see 309577 316 193394 NUT, retaining 2 303 316 306A 306B 65 24G881 Motor Control Board DIP Switch (SW2) need to be set for an E-30. 1,2,3, ON 4 OFF. See page 34. TI10966a 312066Z 71 Dimensions Dimensions Dimension A B C in. (mm) 46.0 (1168) 31.0 (787) 33.0 (838) A C B 72 TI10953a 312066Z Technical Data Technical Data Category Maximum Fluid Working Pressure Data Models E-20 and E-30: 2000 psi (14 MPa, 140 bar) Model E-XP1: 2500 psi (17.2 MPa, 172 bar) Maximum Fluid Temperature Maximum Output Model E-XP2: 3500 psi (24.1 MPa, 241 bar) 190°F (88°C) Model E-20: 20 lb/min (9 kg/min) Model E-30: 30 lb/min (13.5 kg/min) Model E-XP1: 1 gpm (3.8 liter/min) Output per Cycle (A and B) Model E-XP2: 2 gpm (7.6 liter/min) Model E-20 and E-XP1: 0.0104 gal. (0.0395 liter) Model E-30: 0.0272 gal. (0.1034 liter) Line Voltage Requirement Model E-XP2: 0.0203 gal. (.0771 liter) Parts 259024, 259025, 259026, 259028, 259057: 195-264 Vac, 50/60 Hz Parts 259029, 259030, 259031, 259032, 259059: 338-457 Vac, 50/60 Hz Amperage Requirement Heater Power Parts 259033, 259034, 259035, 259036, 259058: 195-264 Vac, 50/60 Hz See Table 1, page 9. Model E-20: 6000 Watts Model E-30 and E-XP1: 10200 Watts Sound Power, per ISO 9614-2 Models E-XP2 and E-30 with 15.3kW of heat: 15300 Watts Model E-20: 80 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm) Model E-30: 93.5 dB(A) at 1000 psi (7 MPa, 70 bar), 3.0 gpm (11.4 lpm) Model E-XP1: 80 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm) Model E-XP2: 83.5 dB(A) at 3000 psi (21 MPa, 210 bar), 1.0 gpm (3.8 lpm) Sound Pressure, 1 m from equipment Model E-20: 70.2 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm) Model E-30: 83.6 dB(A) at 1000 psi (7 MPa, 70 bar), 3.0 gpm (11.4 lpm) Model E-XP1: 70.2 dB(A) at 2000 psi (14 MPa, 140 bar), 0.5 gpm (1.9 lpm) Fluid Inlets Fluid Outlets Model E-XP2: 73.6 dB(A) at 3000 psi (21 MPa, 210 bar), 1.0 gpm (3.8 lpm) 3/4 npt(f), with 3/4 npsm(f) union Component A (ISO): -8 (1/2 in.) JIC, with -5 (5/16 in.) JIC adapter Fluid Circulation Ports Weight Component B (RES): -10 (5/8 in.) JIC, with -6 (3/8 in.) JIC adapter 1/4 npsm(m), with plastic tubing; 250 psi (1.75 MPa, 17.5 bar) maximum Model E-20 and E-XP1: 342 lb (155 kg) Model E-30: 400 lb (181kg) Wetted Parts Models E-XP2 and E-30 with 15.3kW of heat: 438 lb (198 kg) Aluminum, stainless steel, zinc plated, carbon steel, brass, carbide, chrome, chemically resistant o-rings, PTFE, ultra-high molecular weight polyethylene All other brand names or marks are used for identification purposes and are trademarks of their respective owners. 312066Z 73 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505 All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual contains English. MM 312066 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2007, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com Revision Z - January 2015
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : 3.1-701 Marked : True Producer : Acrobat Distiller 7.0.5 (Windows) Copyright : 2007, Rev. Z 01/2015 Job Ref : Z090587 Keywords : "MM 312066, 312066EN, 312066-EN, 312066EN-Z, 312066Z, Reactor, Electric Proportioners, Repair-Parts, English, E-20 Series - 259025, 259030, 259034, E-30 Series, 259026, 259031, 259035, 259057, 259058, 259059, E-XP1 Series, 259024, 259029, 259033, E-XP2 Series, 259028, 259032, 259036" Web Statement : 312066Z, Reactor, Electric Proportioners, Repair-Parts, (English) MM 312066 Modify Date : 2015:03:12 12:59:40-05:00 Creator Tool : FrameMaker 11.0 Create Date : 2005:04:27 11:19:54Z Metadata Date : 2015:03:12 12:59:40-05:00 Format : application/pdf Description : 312066Z, Reactor, Electric Proportioners, Repair-Parts, (English) MM 312066 Title : 312066Z, Reactor, Electric Proportioners, Repair-Parts, (English) Creator : Mike Jueneman Subject : MM 312066, 312066EN, 312066-EN, 312066EN-Z, 312066Z, Reactor, Electric Proportioners, Repair-Parts, English, E-20 Series - 259025, 259030, 259034, E-30 Series, 259026, 259031, 259035, 259057, 259058, 259059, E-XP1 Series, 259024, 259029, 259033, E-XP2 Series, 259028, 259032, 259036 Document ID : uuid:fb045a8f-5e64-4062-896b-86d130b9068a Instance ID : uuid:0b3bec8f-927b-4275-b2cb-358312ba9c11 Page Count : 74 Author : Mike JuenemanEXIF Metadata provided by EXIF.tools