GuangZhou Walkera Technology DEVO-8S 2.4G Transceiver User Manual Part 4of6

Download:
Mirror Download [FCC.gov]
Document ID	1630790
Application ID	6uvVLNLWWOnTYB4Cl5WrYQ==
Document Description	Users Manual Part 4of6
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	409.48kB (5118514 bits)
Date Submitted	2012-02-03 00:00:00
Date Available	2012-02-03 00:00:00
Creation Date	2012-01-31 13:54:31
Document Lastmod	2012-02-01 08:42:05
Document Title	Users Manual Part 4of6

Welcome to use the DEVO—Bs transmitterw
DEVD-ES
(2) Setting method lor Curve in Program Mix2
Touch the item Curve in Program Mix 1 and expands an enquiry “All Servos Hold?" Click OK tor all the servos
will be locked at the current statuses: click Cancel tor unlocked. Enter the next intertace after clicking
(2.1) Master channel setting
Touch the navigalion mark ol Masler and expand a selectable
dropdown menu Select the desired channel and its name
will be shown in Master Click the navigation mark of Master
to return to the interface ot Program Mix 1
(2 2) Slave channel setting
Touch the navigation mark or Slave and expand a selectable
dmpdown menu. Select the desired channel and its name
will be shown in Slave Click the navigation mark of Slave
again to return lo the interiace of Program Mix 1.
(2.3) Exponential
Touch the navigation mark of Exponential and expand a dropdown menu with two options at Off and On.
The pitch curve will be smoothly changed if choosing On Othenlvise choosing Off.
(2.4) Point selection
Touch the navigation mark ol Point and expand a dropoown menu with
seven points. Click the point you want to set, and then touch the navigalion mark to return.
(2.5) status
Touch the navigation mark of Status and expand a dropdown with two options of lnhioit and Active. Touch
lnhibit for unchanging the current amount (the oelault setting is inhibit); click Active for changing the amount.
liAclive is selecled, another Item Output will be shown below
(2.6) Output
Touch the left or right navigation mark or Output to decrease or increase. respectively. the output amount. lt
is possible to reverse lhe mix direction by changing lhe plus or minus sign before the amount. The adjustable
range is 1125%
(2.7) Switch
Touch the navigation mark at Swltch and expand a usable dropdown menu Select the desired switch, and
then click the navigation mark to return
Click the icon H to return to the intertace of Program Mix for other setting, or click the icon H once again
to exit
3.13 Monitor
This function can display the current statuses and positions 01 all the channels’ outputs, and check the current
working status ol each channel.
Touch the icon 5 to enter Function Menu, and then click
the icon . to enter the monitor intertace tor checking
the current working status of each channel
Click to the icon fl exit after finished
3.14 Fail Safe
There are two possibilities tor use if the transmission signal is under abnormal condition. The first one is to
lock the last action data received; the second one is to execute the preset data which is previously set. The
default settlng is Servo Hold.
Deva-55447
deUenlion
Deva—es Welcome to use the DEVO-BS transmitter
Setting method:
Touch the icon I! to enter Function Menu. and then click - to enter the rail safe interface Take the item
Elevator as an example to explain
Elevator setting:
Touch the item Elevator and expand a sub-item in its right. Click the let or right navigation markto decrease
or increase. respectively, the position amount which oenters on the neutral point of servo
The setting methods tor other channels are same as above
Click the icon “to exit atterfinished
Note: checking, whether all the actions when fail sate happened are correct, is a must after the setting is
finished it is dangerous to use full throttle especially atterfail sate taken place
3.15 Tralner
Two DEVOVBS transmitters working together can execute the training function to meet the requirements for
the beginner. The setting method is shown as below:
(1) Data copy
Using the wireless copy function of two DEvoeas equipments. the model data saved in the trainer‘s one can
be transmitted to the trainee's to ensure that the model parameters are exactly same Regarding the copying
method, refer to “2 4 Model Wireless Copy" at “Part Two: Helicoptel" Then follow the steps below:
tinkeg can at
(2) Linkage trainse's DEV ss
insert one end of the signal Wire into DSC socket at the rear
face or the trainees DEvo-ss, and then turn on the power.
A linkage icon will be shown on the boot screen Find out
the trainees model data at its DEVO—BS.
Turn on the power of the trainer's DEV0785. Find out the
trainees model data. and let the trainer's DEVO—BS bind
with the helicopter model and fly it normally. Then turn otf
the power
insert the other end of the digital signal wire into the trainer's
DEVOVBS. and then turn on its power. A linkage icon will
be shown as below:
DEVO-Es —35
oleUerllion
DEVD-ES
Welcome to use the DEVO—SS irarlsrnitter
Two ends or digital signal WIrE
Training status display when the trainer‘s ioon turns into x the trainee stops tlying and the trainer is working,
when the trainers icon turns into "9" the trainee is flying and the trainer is in leisure.
Trainee s olland
trainer worhing
(3) Usage method Right trim
The training swrtoh is letttriming button or nghttnniing
button (can choose by yourselves),the factory setting
is right triming buttonshow as below pic:
During flight ii the tminer pushes Right Trim once, the lingkage icon Will be shown as“ ‘that means the control
right is moved to the trainee lrorn Trainer. lllrainer pushes Right Trim once again, the linkage icon will he
shown as “x" that means the trainer takes back the control righl from the lrainee
(4) Setting lor training function channels
Trainee is available to get full or part oi llight control power to the helicopter model via setting the training
function channel in Ihe trainer‘s DEVO-BS Below is the selting method
Touch the shorlcut icon - to enter Funcliurl Menu, and (hen touch - in Furmtlon Menu aucess I0 Trainer
screen The available channels are shown below‘ and Ihe current slams cl trainer swilch TRN is also shown
Press the navigation sign or the szch the there will come
oul two Choicesilefl trlmlng button and left lrimlng bulton,
press the opiion for the TRN
Touch the channelts) which you desire to grant to trainee.
The channel(s) you have touched will be activated as
“Active“ The channels which are not granted to trainee
keep inhioiled. The default setting is lnhihit
Touch 5; to exit
DEvD-ES—SS
JeUeniion
Deva—es Weicome to use the DEVO-BS transmitter
3.16 Timer
There are two timers which can be set as stopwatch and countdown. respectiveiy The running. stop. or
cieerence of each timer can be operated by setting switch or by touching the shoricui icon.
Setting method:
Touch the icon I! to enter Function Menu, and then click the iconu to enterihe iimerinterface
Stopwatch View Countdown View
Take countdown manner as an exampie to expiain:
(1) Setting icr Timer 1
(1 1) Timer 1 setting
Touch the navigation mark of Timer 1 and expand a dropdown of Stopwatch and Countdown Seiect the
desired timing method The timing range cistcpwatch is from o to 59:59 (59 minutes 59 seconds)
(1 2) Switch selection
Touch the navigation merk oi Switch and get a seiectahie
dropdown
We can select the desired item except these items of ELEV
DIR‘ AILE DIR, RUDD D/R, and GEAR SW which shouid
be previously set at Stick Position Switch at Model Menu
(1 3) Set time
The senable countdown time range is from 00:05 to 59:55.
(2) Setting for Timer 2 is same as that tor timer 1.
Touch the icon H to exit after finished
DEVO-Es 740
oleUen ion
DEVO—BS
All the lunctional settings. which are relative
Pa rt th fee to the operation system cl DEVO—BS itsell,
are fully integrated in System Menu They
include Language, Display, Buzzeri Touch
Airplane Screen Calibration, Stick Mode, Stick
Calibration , and About.
m— Welcome to use the Devoaas transmitter
DEVD-ES
0 System Menu
The boot screen 01 airplane is shown as below:
Throttle tnrn Flap him right
Elevator trim
Flap w" M Transmisslon power display
Battery volume
ulsplay
Flight mode Model name
Timer
Function menu
Timer .
ioon
Throttle percentage
value
System menu
icon
Rudder trim
Throttle Dual tale and Model Alleron lrlm
curve icon experiential menu loan
loan
1.1 Language Setting
Touch the shortcut icon-to enter System Menu and then touch-to enter Language. Touch the language
that you want to select. A t " will be shown on the screen after selected.Then touch 51 to save and exit.
1.1 Language Setting 1.2 Display
1.2 Display
Touch the shortcut icon .to enter System Menu and then touch the icon i to enter “Display"
Three items are available to be set as below:
(1) Becklight Lightness: the backlight brightness can be adjustable by touching the navigation marks The
power consumption will be increased if the backlighl lightness is too bright and the battery cruise duration
will be shortened
(z) Backlight timeout: it is possible to set the duration which LCD stays at highlight in the lorm oi Always on
and duration from 5 to 60 seconds with an interval ol 5 seconds.
DEVO-ES 742
cieUeniiort
Welcome to use the DEVO-BS transmitter
Deva-as
(3) Power save time: it can adjust the backlighting duration by turning or the hackltght in order to prolong
the battery cruise time The setting status contents Always On and duration in so grades with an interval
011 minute.
Touch H to exit
1.3 Bueramlng
Touch the icon .to enter System Menu and then touch-to ertter Buzzer interfaoe
(1) Buzzer switch: touch the navigation mark at Buzzer Switch
and pop up an aiterrtative item: of! and Orr If touch On
a (imp-down menu wili be shown beiow.
(2) Throttle stick: under Buzzer Switch is at the status orOn,
if Throttle Stick ls set as “Active". a relative musical scale ,
will make response when moving the throttle stick. You
can judge the position at the throttle stick according to
the diiferent musical scales. Also. it can be set as inhibit.
(4) Buzzer tone: the tone is composed of to grades You can choose the favorite tone according to your
interests Touch Test to make a listening test
Touch H to exit afler finished.
1.‘ TFT Screen Calibration
Touch the icon . to enter System Menu and then touch - to enter TFT Screen Calibration.
Click anywhere on the screen to start calibration with
the touch pert. and then iollow the indication to calibrate
lt will automatically return to System Menu after the
calibration is finished
1.5 Slick Mode
Touch the ioon . to enter System Menu. and then touch the icon . to enter Stick Mode
There are tour stick modes lrcm MODE 1 to MODE 4. Seiect the stick mode you desire and then touch the
icon “to exit
DEVD -Es — 43
cleUerllion
DEVD-Ss
Welcome to use the DEV078S transmitter
1.6 Stlck Callbratlon
Touch the icon to enter System Menu and then touch the loan . to enter Stick Calibration There are
two items in the interface: Stick Direction and Stick Calibration
(1) Stick direction: there are tour options: Elevelor. Aileron,
Throttle, and Rudder Click the ilem, which you want to
reverse, to change the output direction at the stick The
default setting is Normal.
(2) Slick calibration: rverlenoe happened in sticks , ii would
be calibrated vle this option
Method tor calibration:
Click the display item of Start to enter the status of calibration,
and Start will be turned into Stop
(2 1) Stick calibration: Clockwise or counter clockwise mechanically move the right stick and leit sticks from
their minimum levels to their maximum levels several times, and then return the sticks to the neutral positions
respectively
(2 2) Click the display item of Stop lf the calibration is finished, “Calibration success!" Will be shown on the
lower of the screen If the calibration is failed‘ “Calibration error! Please Iry again!“ will be shown instead lt
needs to be calibrated again.
(2.3) Rercalibration: directly repeat the said steps 2 1 and 2.2 in the failure interface
Touch the icon H to exit
DEVO-Es —M
cieUenlion
Welcome to use the DEVO-BS transmitter
sto -55
1.7 About
Touch the icon I to enter System Menu and then
touch - to get acoess to the about interface You
can check the versions oi hardware and software.
Click the loo" H to exit
Lv)."~l£ut
. minim v.10"
7mm 5mm yawn
Lum_ vuoozr
20 M eI Menu
Model Menu manages all the model data saved in Devoeas It includes Model Select. Model Name. Model
Copy. Model Transmit. Model Receive. Model Reset. Type Select. Trim System, Device Select. Device Outpul.
Wing Type,PowerAmpliiier and Fixed ID
2.1 Model Select
Touch the icon - to enter Model Menu and then click the icon = to enter Model Select.
Touch the model you desire The selected model is changed in orange color Then click the icon“ to exit
2.2 Model Name
in Me menu of Model Name. you can make a desired name for your model lor long term storage its data
can be directly wilhdrewn in lhe next flights Repeal lhe slep “2.1 Model Select" lo choose the model you went
to name or save And then touch the icon to exit
Click the icon . I0 enter Syslem Menu and Ihen click lhe icon - to gel lhe model name interface. The
following is the intertsce:
DEVD -ES — 45
oleUenlion
DEVO-ss Welcome to use the DEVOVSS transmitter
Click ihe right blank frame of Name and a gray stripe will be shown in the frame. Touch the reium key
lo clear up the old name Touch the soft keyboard lo input a new name u is possible lo swilcn
between lowercase and uppercase by clicking the key Tu"...— Then (ouch Ilo exit
2.3 Model Copy
Touch the icon . to enter Model Menu and click um enter Model Copy.
Choose the model you wanl Io be oopied as source model. The serial No. and model name of Source Model
will be shown in the let] side loe lnlerface.
Then touch the model in the right list where you want to locate the source model. The serial No. and name
otthe model you chose are shown under Dest Model in the lower lefl cl interlaoe as well as an enquire "Are
you sure?" is popped up.
Click OK to copy. Olherwise click Cancel. Tnen Ihe inlerface will be automalically returned Io Model Menu.
Click to save and exit
2.4 Model wireless copy
The model data between two DEVOVSS equipments can be wirelessly copied via Model Transmit and Model
Receive in Model Menu
(1) Model transmission
Touch the icon . to enter Model Menu and then
continue to click the ioon - to enter Model Transmit.
DEVO-ES—AE
(ieUeniion
Welooms (0 use the DEVO-BS transmitter
DEVO -as
Choose the source model which will he transmltted The serial No and name of the source model will be
shown under Select Model in left side of the interiace as well as enquiry information “Ale you surs7" in the
right side.
Click OK lor transmission or Cancel lor relection. Enquiry information ‘Transmitting 444444 ' appears after
Clicking OK. Touch the icon to exit.
(2) Model receiving
Touch the shortcut icon-to enter Model Menu and then touch the iconnto enter the model receive interface.
Enquiry information "Are you sure?" is shown in the center of the interface.
Click Ok for reosiving or Carmel (or rslsction “Connecting ...... " and “Receiving ...... " will be shown in
series in the interface The information of “Received" with the model name will be shown in left side after
receiving is finished.
Choose the save position in the right name list by touching.
Enquiry inlorrneiion “Are you sure?" is shown alter clicking
the save position Click OK for save and the ounent lnterfeoe
will automatically return to Mode Menu Click Cancel lor
rejection
Touch the icon to exit
DEVD -Es — 47
clellerlliort
DEVD-Ss
2.5 Model Reset
Welcome to use the Devoras transmitter
All the model data can be restored to factory settings via Model Reset
Touch the icon - to enter Mcdel Menu and then Click . to enter Model Reset.
lt is possible to store up to 12 models data in the model list of DEVO—BS equipment. There are two methods
to reset the model dale: batch resel and single reset.
Reset all the models Scroll hr
Reset single model
(1) Method (or batch reset
Touch "All Mudels" in Model Reset intertace. Then "All Models" and enquiry "Are you sure?” appear in the
left side Click OK for reset, or Cancel lcr rejection
(2) Method tor single reset:
Touch the upper or lower navigation mark to move the scroll par, and then chccse the rncdel you want tc
restore in the model name list The selected model's name and serial No. and an enquiry “It is in use! Are you
sure?" appear in the left side. Click OK for reset. or Cancel for rejection.
Click the icon n to exit
2.6 Type Select
This device offers two model types menu They are
heliccpter and airplane.
Touch the icon I to enter Model Menu and then
click - to enter Type Select Choose the model type
and then touch the icon H to exit.
nsvo—ss 748
deUeniiori
Welcome In use lhe DEVO-BS transmitter
DEVD -55
2.7 Trim System
Trim System is able to finely tune the following Six items, respectively: elevator. aileron. rudder, throttle, left
trim. and right trim. The trim range is covered from 1 to 20 grades (factory default is set at 4) it is convenlent
to subtly modify the pitch by adjusting the trim range.
Touch the icon - to enter Model Menu and then click ' to enterTrim System
Touch the corresponding navigation mark to change the
trim value The bigger the trim value is, the biggerttte trim
range will be.
For elevator, aileron. and mdder. there are two more options:
Normal and Limited. "Normal" means the Irlm is always
working allhuugh the corresponding stick slsys anywhere.
“Limited" means the trim is out of working when the
corresponding stick is at maximum position
Click the icon u to exit.
2.8 Davin. Select
This setting can help you configure various functional switches, or adjust levers according to your flight habits
lt includes Flight Mode Switch. Fllght Mode Trim , Throttle Hold Switch, Flap Switch Select. and Flap Trim
Select.
Frlendly reminder: This function is frequently utilized in fllgnts Modelers will be greatly favored if expertly
mastering its usage
Setting method:
Touch the icon - to enter Model Menu. and then click the icon - to enter Device Select.
(1) Flight Mode Switch
Touch the navigation mark of Flight Mode Switch to expand
into a dropdown menu Choose the mode switch you desire.
The factory default setting is inhibit.
(2) Flight Mode Trim Select
There are two modes: common and Flight Mode. in Common
mode all the trim values. to which various sticks are relative.
put egually effects on all the flight modes
ln Flight Mode, the trim values to which each stlck is relative pvt. respectively. effect on the corresponding
stick. The factory default is Common.
(3) Throttle l-lold Switch
Touch the navigation mark of Throttle Hold Switch to expand into a dropdown menu Choose the mode switch
you desire. The factory default setting is RUDD DIR
(4) Flap Select Switch
Touch the navigation mark of Flap Select Switch to expand into a dropdown menu Choose the mode switch
you desire The factory default setting is Mlx SW
(5) Flap Trim Select
Touch the navigatlon mark of Flap Trim Switch to expand into a dropdown menu Choose the mode switch
you desire The factory default setting is LEFT TRlM.
Deva-55418
cleUerliion
DEVD-Ss
2.9 Device Output
Device output is composed orlour items. it can set up output switches and select the usage oitrim. respectively.
ll can also activate, inhibit or use oiherfunclions.
Friendly reminder: This iunction is ireouently utilized in flights Modelers will be greatly iavored ii expertly
maslering ils usage.
Setting rnelhod:
Touch the-icon lo enter Model Menu and lhen clickcto enter Device Output.
Welcome to use the DEV078S transmitter
There are lour items to be adjustable They are Gear.
Flap, AUXZ, AUXS, The setting methods fur them are
shown below:
(1) Gear
Touch the led column navigation mark oi Gear and pop up an expansion including FMOD sw. MIX sw, ELEV
DIR. AlLE D/R, RUDD D/R and GERA sw Touch the desired item. The default setting is GEAR sw
Touch the right oolurnn navigation mark ol Gear Pop up an expansion including inhibit, Active, Gyro. Governor
Tuuch the desired item The default setting is Active
(2) Flap
There will show the switch option only afler the right column oi Flap is selected. Touch the right column of
Flap and expand a dropdown menu including Inhibit. Active, and System.
(2 1) if choose inhibit or Active, the expansion menu will include these items: FMOD SW, MIX SW‘ Left Trim
and Right Trim. The default sening is MlX SW Select the desired item as the flap switch.
(2.2) if System is chosen, it means default setting MIX SW be choosed.
nsvo—ES , 50

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Modify Date                     : 2012:02:01 08:42:05+08:00
Create Date                     : 2012:01:31 13:54:31-08:00
Metadata Date                   : 2012:02:01 08:42:05+08:00
Format                          : application/pdf
Document ID                     : uuid:1342d574-735b-d848-a6ab-6e364da4bb7c
Instance ID                     : uuid:93d55196-37d2-4c13-920e-654264f4d9c6
Has XFA                         : No
Page Count                      : 14

EXIF Metadata provided by EXIF.tools