GuangZhou Walkera Technology DEVO-8S 2.4G Transceiver User Manual Part 5of6

Download:
Mirror Download [FCC.gov]
Document ID	1630791
Application ID	6uvVLNLWWOnTYB4Cl5WrYQ==
Document Description	Users Manual Part 5of6
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	406.03kB (5075327 bits)
Date Submitted	2012-02-03 00:00:00
Date Available	2012-02-03 00:00:00
Creation Date	2012-01-31 13:54:31
Document Lastmod	2012-02-01 08:58:57
Document Title	Users Manual Part 5of6

Welcome to use the DEVO-BS transmitter
(a) Aux 2
Touch the left column navigation mark at AUX 2. Pop up an expansion list including FMOD sw, Mix sw.
ELEV DIR,AILE D/R,RUDD DIR, GEAR sw .Touch the desired item The default setting is FMOD sw
Touch the right column navigation mark oi AUX 2, and expands a list including lnhibit, Active, Gyro,and
Governor Click the desired item The default setting is Active Tnen continue to set other Ilems
(4) Aux 3
Touch Ihe lefl column navigafion mark 01 AUX 3, and expands a list including FMOD SW, MIX SW, ELEV
DIRAILE D/R,RUDD D/R, GEAR SW Touch the desired item The laclory delaull setting is RUDD D/R
Click the right column navigation mark oiAuxs, and see an expansion list including lnhibit, Active, Gyro and
Governor Choose the desired item The factory fault setting is Active Then continue to setup other items Click
the icon to exit.
2.1nWing Typo
Wing Type is grouped into Flaperon, DLETA and v Tail
Wing type selection:
Touch the icon-to enter Model Menu, and then touch to enter the wing type interface
DEvo-as—sl
o'eUention
w— Ws‘came to use the DEVOras transmitter
(T) Flaperun
Touch the nawgauon mark at thg Type and expand a dropdown menu wttn Normat FTaperon and DELTA
Choose tna desved ng type
(T ‘U Fwapemn
Bemw IS the grapmcs tor the servos locatmn loe flap and Aneron Type.
Left aTlerun RTgnt aneran
Canned In the uutput AuxT m Recewer Connect In Ihe uulpuIAILE m Recelver
(1 2) DELTA
Bemw s the graprncs of the servos Tacanon 0! ma Della Type
Left AHeron nght ATIeran
Connect to Ihe autpul AILE m Recewer Connect I0 Ihe uulpul ELEV m Recewer
(2) v-TAIL
Touch the navigation mark ulV-TNL and expand a dropdcwn menu with mm and Active Chonse Active
Bemw s the graphms tor Ihe servos Iocahon Dune v-tan Type
Left ernpennage Tgnl empennage
Connect (a Ihe output ELEV tn Recewer Cennect (a the output RUDD m Recenver
(3) Dual channels semng
Dua‘ Channe‘s can be set as Elevator‘ Awleron‘ Rudder, or F‘aperon It is of dua‘ channe‘ output function
The channel, whwch wi‘l be set as dual channel alAUX in Demos Outpul (Referlo “2 9 Dewce Oulpul") shmfld
be previeus‘y set as Inhwbwl when [he AUX channel Ts bemg set
Deva—Es —52
cieUeniion
DEVCI as
Welcome to use the DEVO-BS transmitter
Setting method:
(3 1) Channel setting
Touch the navigation mark Qt Channei in the interface of
Wing Type, and expand into Elevator, Ailerun, Rudder, and
Flap We take Elevator as an example
(3.2) Mate setting
Click the navigation mark at Mate and expand a dmpdown
menu with inhibit, Gear. Flap, AUX2 and Auxs.
Touch the desired channel in black. The channei, whose
characters are shown in gray, has being applied
(3 a) Trim setting
Click the navigation mark of Trim and expand a submenu with inhibit, Left Trim and Right Trim Choose the
item that you want to select as trim iever.
(3 1) Channei setting
(3.2) Mate setting (3.3) Trim setting
(3 4) the settings torAileron, Rudder, and Flap in the item Channel are same as above
(4; Twin Engine
This tunctien can be set as twin engine output to meet the requirement for the models. which are powered
by twin engines
(4 1) Mate setting
Click the navigation mark of Mate and expand a dropdown menu with inhibit and the inhibited channels
previously set in “2.9 Device Output" Choose the desired channel in biack. These channeis in gray are not
available
(4 1) Mate setting
(4 2) Trim setting
(4 2) Trim setting
Click the navigation mark at Trim and expand into Inhibit, Left Trim,Right Trim.Tuuch the item which you want
to set as the trim
Click the icon to exit aflerfinisheu.
DEVOsESf 53
oieUeriiion
Dames Wetoome to use the Devoeas transmitter
2.11 Power Amplifier
The transmission output power of DEVOVES is adjustabie.
it‘s Vaiid to set different wattage tarditferent modth is divided
into six grades from smeit to big. The tower the transmission
output power transmits, the shorter the radio range is. and
the ionger the stand-by time will be The higher the
transmission output power. the tarer the radio range. and the
shorter the standby time. Choose the appropriate transmission
output power according to the actual situation.
Setting method:
Touch the icon - to enter System Menu and then click - to enter the power ampttfier interfacecttuuse
thsappropriate output power ievet and then touch H to exit
2.12 lead ID
This setting wtii bind Devo-as and its receiver in a unique corresponding retationship it wiii greatiy speed
up the time otautomattc binding when DEVO-SS powered on
(1) Setting for fixed ID
The setting tor fixed in shoutd be under the status that automatic in binding is sucoesstuity finished Below
is the setting method
Touch the icon. to enter Modei Menu in the main interiace, and then enter Fixed in by touching the teen
-in Modet Menu.
Touch the navigation mark oilhe item ID Code Sefling It wili expand into two statuses: OH and On. A series
oi random digits witi be shown heiow eitertouohing On
A mini soft keyboard is shown in the tower part after touching the random digits of D Code
set sot random
its shown here
DEVO-ESfS‘l
cieUeniion
DEVD -55
Welcome to use the DEVO-BS transmitter
The new lD digits can be modified by touching the mini soft keyboard. Then touch Match afler the new D is
aireauy set An inquiry interface of "Are you sure?" pops up. “ID Code Match. . . u u .” will be shown after touching
0K
(2) Fixed ID cancellation
insert the assorted BIND PLUG into the output terminal of BA'I'I' before the receiver is powered on. and then
plug SV DC power into one at the other output terminals The red light of receiver will flash slowly. This means
the fixed ID code has been cancelled. Pull out BlND PLUG.
hifi'
(CB
DEVO-BS also needs to make relative cancellation and reversion after the fixed D in receiver is cleared out
in the main interface touch the icon-to enter Model Menu and then touch - to enter Fixed lD. Touch lD
Code Setting to expand the nawgation mark into two statues On and on Touch Off Then touch“ to exit
Func n Menu
Function Menu is used to make personalizedly tine adjustment to the selected models it includes Reverse
Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential, Throttle Hold, Throttle Curve, Differential setting.
Balance setting, Gyro Sensor, Governor, Aileron to Rudder Mix, Elevator to Flap Mix, Rudder to Aileron/
Elevator Mix, Flap System, Aileron to Flaperon Mix, Program Mix, Monitor, Fail Safe, Trainer, and Timer
3.1 Reverse Switch
Touch the shortcut icon - to enter Function Menu, and then click the icon 0 to enter the reverse switch
intertaee
There show all the reverse switches' statuses ofS channels.
Touch the desired item to reverse its current status The
status includes two types: Normal and Reverse. The default
setting is Normal
Touch the icon u to exit after finished
DEvo-as—55
oieUeniion
DEvo-Es Welcome to use the Devoass transmitter
3.2 Travel Adiust
Touch the icon- to enter Function Menu and then click the icon alt) enter the servo travel adjust interlace.
The interface contents two pages to show the current travel
status olell the erght channels. Touch the navigation mark
of each item to increase or decrease corresponding travel
adjustment amount The adlustable rangers u o% ~150 0%
The default setting is 100 0%
Click the icon H to exit atterfinistled.
3.3 Sub Trlm
Sub Trim is used to make parallel movement of servos lt is recommended to adjust the servo bell crank if
the servo is far away lrom its neutral point The excessive usage olsub trim may damage the servo
Setting method:
Touch the icon-to enter Function Menu and then click the icon to enter the sub trim interface.
Touch the navigation mark of the desired item to adlust the amount for rectifying the servc's neutral point. The
default neutral point is set at u w, The adjustment range oleaoh channel is shown as below:
Channel name Adlustment range
Channel name
Adiustment range
Elevator D62.5%—U62.5% —62.5%— +62.5%
Ailerun R62.5%7L6245% Flap D62.5%7U62.5%
Thrctlie L62 . 5%TH62 . 5% Gym T62 a 5%T +624 5%
Rudder R62.5%TL62.5% AUX3 762.5%7 +62.5%
Note: the model names shown will be difterent with the selected channels difterent
Click the icon n to exit after finished
3.4 Dual Rate and Exponential
it is possible to use D/R switch to control dverthe dual rate dlelevator, aileron, and rudder afterthe function
of Dual Rate and Exponential is set up. The setting range is 0-125%. Under the help with exponential curve
adjustment. it is not only manually but also automatically ahle to set up various parameters which are suitable
for yourselt
Deva-55 —55
cleUenlion
Welcome to use the DEVO-BS transmitter
DEVD-as
Setting method:
Touch the icon-to enter Function Menu and then click the icon .to enterthe dual rate and exponential
interface.
(1) Channel selection
Touch the navigation mark cl Channel and expand a
selectable list including Elevator. Aileron. and Rudder.
Click the desired channel which will be shown in Channel.
(2) Position selection
Touch the navigation mark of Position and expand a
selectable list including Pos 0. PBS 1. and Pos 2. Click
the desired item which will be shown in Position. But there
will only show Pos 0, Pos 1, and Pos 2 in manual setting.
Irtouett this mark, both the upper
end lower curves will being .
changed at the same time (3) Dual Rate adlustmsnt
it is possible to modiiy the value by touching the navigation
mark of Dual Rate
. 7 it touching the navigation mark for just one item to amend
1 . 1 the dual rate value, the dual rate ot the corresponding
I, much ‘ servo will be changed in one direction, while the curve
upper or lower curv will being changed in one direction at the right graph.
changed
(4) Exponential adjustment
It is possible to adjus1 the exponential output value of the servo at that point, which is set up in step “(2) Position
selection". by touching the navigation mark oi Exponential
(5) Automatic setting
Under worxing with Flight Mode, it is possible to switch between the dual rate and exponential, which are set
in above (3) Dual Rate adjustment and(4) Exponential adiustment, respectively.The settings lor Flight Mode
0, Flight Mode 1, and Flight Mode 2 are available
Flight mode i
Note: Before using the function at automatic setting. both
Fllghl Mode Switch should be previously set as relative
switches Reler I0 “2 8 Device Select"
Touch the flight mode that you want to set as automatic operation, and an expansion list will be shown Click
the desired position If Switch is selected, it is only controlled by the corresponding dual rate lever
Click the icon H to exit
DEvO-BS—57
cieUeniion
DEvo-ss Welcome to use the DEVOVBS transmitter
3.5 Throttle Hold
If this function is set. the switch Wiii be executed by RUDD DIR switch. The setting vaiue of throttie haid is
ranged from 720.0"/a to 50.0%.
Setting method:
Touch the shortcut loan -to enter Function Menu, and then click . to enter the throttle hold interface.
Touch the navigation mark oi Hold Status, and an expansion list will be shown as inhipit and Active. Click
Active, there appear Switch, and Hold Position in the ioliowrng interiaoe
(1) Setting tor Switch
This item is impossibie to be set The default setting is RUDD DIR
(2) Setting tor Hoid Position
Touch the ieft navigation mark oflhe item Hcid Position to decrease the position amount, whose minimum is
-20 0%; touch the right to increase the position amount whose maximum is $50 0%
Ciick the icon H to exit after ail the settings are finished.
3.5 Throttle Curve
Throttle curves are adjusted through seven points. which of all the flight modes can be respectively set. The
left and right throttles can be separately set after it is previously set as dual engines Reier to Twin Engine
at “2.10 Wing Type"
Setting method:
Touch the loan - to enter Function Menu and then click the icon -to enter the throttle curve interrace. A
dropdown menu with “AM Servos Hold?" pops up Click OK for all the servos locked at the current statuses.
Click Cancei for all the servos unlocked.
Deva-55 —55
Weicome to use the DEVO-BS transmitter—M
Deva-as
(1) Channel settlng
Aner previously set up Twin Engine, touch the navigation
mark oi Channel and expand a list including Left Throttle
and Right Throttle. Select the desired throttle which will be
shown in Channel Channel will be shown in grey it Twin
Engine is not previously selected
t2) Position selection
Touch the navlgation mark of Position and expand a list with Pos 0 and Pos 1 select the item you want to
set.
(3) Exponential setting
Touch the navigation mark oi Exponential and expand a list with on and On. The throttle curve will being
changed smoothly ii clicking oh
(4) Point setting
Touch the navigation mark oi Point and expand a list
including seven points Seiect the point you want to adlust.
(5) Status setting
Touch the navigation mark of Status and expand a list with
Inhibit and Active Click lnhiblt tor keeping the current value
(the defauit setting is inhibit); click Active for changing the
above point’s value. Another item Output will be shown
below after choosing Active.
(6) Output setting
Touch the leit or right navigation mark of Output to decrease or increase, respectively, the output value The
adjustable range is from u o% to 100 o%
m Throttle setting Switch between Pos 0
, _ _ _ and Pus1wiiibe shown
Touch the ieft or right navigation mark oi Throttle stick to here by moving throttle
decrease or increase, respectively, the amount with a lower
limit oi t) we and an upper limit oi 100 o% The default
settlng is inhibit
The switch between Pos 1 and Pos 0 can be treely realized
through thruttie stick after the above amount has been set
up The above set amount is the position of throttle stick
as well as the switch point.
(5) Switch selection
When the item Throttle Stick is set in Inhibit, it is possible to switch between Pos 0 and Pos 1 by Switch
Touch the navigation mark of Switch and expand a
dropdown menu inciuding the selectable items in biack.
Seiect the desired item whose ieft side wili be changed
into “i" from "0" if two items are selected, the item And
should be chosen Then touch the navigation mark of
Switch to return back
Ciick the icon H to exit after finished.
DEvO-ES—SB
cieUeniion
DEVD-Bs Welcome to use the DEVOVBS transmitter
3.7 Dif'erential
I' want to use this function, Fiaperon, DELTA shouid be previously seiected in Wing Type o' Modei Menu.
Refer to “2.10 Wing Type".
(1) Aiieron diflerential setting:
Touch the shortcut icon -to enter Function Menu, and
then ciick the icon . to enter the interlace of Diflerentiai.
Mounting servos in left and right ailerons are a must if
using this function. The following interface will be shown
after Flaperon. DELTA. selected in Wing Type Referto
"2.10 Wing Type".
(1.1) Setting for Pos 0
Touch the Iefl or right navigation mark of Pos 0 to decrease or increase, respectively, differential value The
bigger the value is. the biggertne differential is. The adjustable range is a 10m.
(1 2) Setting for Pos 1
The setting is same as above.
(1.3) Switch selection
it is possible to switch by setting switch when differential
is in use.
Touch the navigation mark of Switch and expand a
Selectabie lisl. Ciick the switch item, which you desire, to
change “0" into “1" lftwo or more switch items are selected,
the item And should be chosen Then click the navigation
mark to return.CIick the icon to exit after finished.
12> Rudder differential setting
V—Tail should be previously set in Wing Type of Model Menu if the rudder differential function is activated.
Refer to “2.10 Wing Type". And then the following interface will be shown:
(2.1) Setting for Pos 0
Touch the ten or right navigation mark of Pos 0 to decrease
or increase, respectively, differential value The bigger the
value is, the bigger the differential is The adjustable range
is a 100%.
i2.zi Setting for PoS 1
The setting is same as above.
(2 3) Switch selection
it is possible to switch by setting switch when differential is in use.
Touch the navigation mark of Switch and expand a
selectabie Ilsl Click the swilnh llem, which you desire, to
change "0" into “1" iflwu or more switch ilems are Seiec‘led,
And shouid be chosen Then click Ihs navigalion mark to
return Cilck the icon fi to exit after finished
DEVD -es — 60
Weloome to use the DEVO-BS transmitter
(3) Flap diflerential setting
oleUeniion
DEVD-ES
it should be previously set the flap dual channel function in Device Output at Model Menu (refer to “2 10 Wing
Type") in order to activate the menu or Flap Differential.
(3.3) Switch selection
(3 1) Setting lot Pos 0
Touch the left or right navigation mark of Pds o to decrease
or increase. respectively, differential value The bigger
the Value is, the bigger the dilferential ls. The adjustable
range is 11007...
(a 2) Setting tor Fos 1
The setting is same as above.
It ls possible to switch by setting switch when diflerential is in use.
3.8 Balance
Touch the navigation mark of Switch and expand a
selectable list. Click the switch item, which you desire,
to change “0" into “1" if two or more switch items are
selected, And should be chosen Then click the navigation
mark to return.Click the icon to exit after finished
This iunctioh can adjust the parameters oi the two servos which are used in the dual channels it should be
previously chosen one of the these wing types of Flaperon, DELTA, and v Tell in Wing Type at Model Menu
Refer to “2.10 Wing Type".
Setting method:
Touch the lcon - to enter Function Menu. and then click the icon . to enter the balance interface
(1) Channel selection
Touch the navigation mark of Channel and expand a selectable list. Choose the deslred channel.
names—51
oieUeniion
DEvo-Bs Welcome to use the Devoalss transmitter
(2) Point parameter adjustment
Touch the navigalion mark of Point lhat you want lo selecl,
and pops up a dropdown menu including lnhibit and Aclive
Click Active for adiusting the value by touching the left or
right navigation mark. 0% means no adjusting. A minus value
means the amending direction is downward. and a plus value
means the amending direction is upward.
Ciick the icon u to exit alter finished.
3.9 Gyro Sensor
This function offers the gain adjustment (or gyro sensor, which can be manually set through DiR switches or
Flight mode switch, and also is possible to be automatically switched among various gains through flight mode
switch (The flight mode shouid be activated. Refer to -2.a Device select").
Setting method:
Touch ttle icon - to enter Function Menu, and then touch the icon filo entergyro sensor interface
(1) Manual setting
(1 1) Mode selection
Touch the navigation mark 0! Mode and expand into two
opticns: Manuai and Automatic. Select Manuai.
(2 2) Switch selection
Touch the navigation mark of Switch and expand into six
articles: FMOD sw. Mix sw, ELEV D/R. AILE DiR, RUDD
D/R and GEAR sw
(2.3) Channel setting
The default setting is Aux 2. it is possible to alter into other
channels by choosing in the item of Device Output (refer to‘2 9 Device Output")
(2 4) Gain adjustment
There are total three levels for respective setting: Pos 0. Pos 1. and Pos 2
(1 4 1) Pos 0
Touch the left or right navigation of the flight mode you want to adjust to decrease or increase, respectiveiy,
the value with a range 010 0"/o -100.0%
lithe gyro used has two modes ofNOR and Aves, NOR will be activated when the value is less than 50 0%,
and AVCS activated when above so 0% ln NOR mode, the smaller the value is, the bigger the sensitivity
will be; in AVCS mode, the bigger the value is, the bigger the gyro sensor gain will be The factory setting is
50.0%
(1.4.2) Fos 1
Refer to the step of "(1.4.1) Fos D'.
(1 4 3) Pos 2
Referto the step ut“(141)Pos O"
(2) Automatic setting
(2.1) Mode selection
Touch the navigalion of Mode and expand inlo two oplions:
Manual and Automalic Select Automatic
(2 2) Channel oulpul
The default setling is Aux 2. it is possible to alter into other
channels in the interface of Device Output (Refer to ‘2 9
Device Output”)
Deva-55 —52

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Modify Date                     : 2012:02:01 08:58:57+08:00
Create Date                     : 2012:01:31 13:54:31-08:00
Metadata Date                   : 2012:02:01 08:58:57+08:00
Format                          : application/pdf
Document ID                     : uuid:1342d574-735b-d848-a6ab-6e364da4bb7c
Instance ID                     : uuid:84584aa6-adba-4c12-a0bf-a0149e831b17
Has XFA                         : No
Page Count                      : 12

EXIF Metadata provided by EXIF.tools