Guardall a division of CSG Security XLK1 LCD Keypad User Manual 2

Guardall, a division of CSG Security Corp LCD Keypad 2

Contents

User Manual 2

21-3610 rev1.4 xL LCD Keypad Installation Instructions CSG SecurityCorp / Sécurité CSG Corp Page 1 of 2 GUARDALL 5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1sales@ guardall.com +1 905.206.8434 | support@ guardall.com +1 905.206.8436 | Fax: +1 905.629.4970www.guardall.com | +1 877.249.9993 The LCD keypad provides the ability to operate the entire Monitor xL™ or Chubb AFx™ system. It will also provide readouts of the status of the systems and location and nature of alarms. 1,- # 2ABC 3DEF45JKL 6MNOGHI78TUV 9WXYPRSKeypad LEDsRed Flashing: Protection ONSolid: Partial protection (STAY)Green On Always with power present. Yellow On when trouble condition present. Flashing when there is no AC mains.Red Green YellowComsLost #50624efEnter code 428220Z_QXXTo use the keypad tamper spring as a wall tamper break out this plastic cylinder inside the back cover.Screw it to the wall, keeping it in the same hole as it was attached, so the back cover fits over it. The plastic cylinder prevents the spring from being affected by flat objects wedged in behind the keypad. The additional keypad base is optional. For installations using it there is a similar, shorter, washer style, plastic break out. Place it behind the plastic cylinder and screw them down together. Then place the holes in the base and keypad backing over top of them. Fit the spring inside the plastic cylinder part and secure the keypad front to the keypad back. The spring compressing should reset the keypad tamper condition. Knock outs for rectangular conduit using additional keypad base.Keypad BackKeypad FrontCircuit board pin connectors insert into fixed terminal blocks on inside of keypad back. This allows the keypad to make wire connections in the terminal blocks. Terminal BlockTerminal BlockTamper SpringSonalertCableAfter placing the keypad on its back section, make sure the keypad's securing screws (supplied) are always I N !Standard and G-ProxII 143256PT1 0V PT2 PT3 PT4 143256AB0V OUT+12V0VWiegand143256D1 D01432 56AB0V OUT+12V0V 0VPT1 PT2Keypad Terminal Block Wiring Module BusModule BusOutputInput 1Input 2CommonWiegand Reader Data 1 and 0. No reader LED connection.Wall tamper knock outFlip CoverSerial # sticker for programming into Module Programming.Apply dealer's logo label (supplied) in the indented space at the top of the keypad. Apply the Alert Button labels as required.Alert LabelsXXXXXRectangular Conduit (Trunking)Keypad Output goes negative. Interface with a relay or power supply. Common their negatives with keypad 0V.Module Point Assignment: 8 points.First point: Fire Alert buttonsSecond point: Panic (Hold-Up) buttonsThird point: Auxiliary Alert buttonsPoints 4 – 7 are hard wire inputs 1 – 4 on the Standard and G-ProxII version.Points 4 – 5 are hard wire inputs 1 – 2 on the Wiegand version. All unused points are skipped. Point 4 – 7 Point 4 – 5 Point 1 Point 2 Point 3 Ratings:LCD Keypad with ReaderInput: 12 – 13.8VDC, 110mAOutput: 12VDC, 1x10mALCD KeypadInput: 12 – 13.8VDC, 95mAOutput: 12VDC, 1x10mATemp for both: -10°C to +55°C (14°F to 131°F) @ 93%FutureFuture
21-3610 rev1.4 xL LCD Keypad Installation Instructions CSG SecurityCorp / Sécurité CSG Corp Page 2 of 2 GUARDALL 5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1sales@ guardall.com +1 905.206.8434 | support@ guardall.com +1 905.206.8436 | Fax: +1 905.629.4970www.guardall.com | +1 877.249.9993 3 Keypad Versions • LCD Keypad P/N 111-3610 (white), 111-3620 (gray): standard keypad includes 3 programmable alert button inputs, 4 hardwire alarm input points and 1 output point. • LCD Keypad with internal RF reader P/N 111-3611 (white), 111-3621(gray): keypad includes 3 programmable alert button inputs, 4 hardwire alarm input points and 1 output point. Includes a built-in RF G-Prox reader. • LCD with external Wiegand reader Keypad P/N 111-3612 (white), 111-3622 (gray): keypad includes the capability to connect an external Weigand reader to it. Keypad includes 3 programmable alert button inputs, 2 hardwire alarm input points and 1 output point. NOTE: – Double or triple card touch (badge) to LCD with external reader is the equivalent of hold a card (badge) feature at the LCD with internal reader to e.g. turn protection on and off. – GProxII and MIFARE readers have been proven to work acceptably when connected to the LCD with external reader. All versions • Communicate with the main control unit on the SNAPP module bus. • Backlit, 2x16 LCD display. • Colours: white, grey. For further keypad information, please see the Monitor xL™ or Chubb AFx™ Simplified or Advanced Installation and LCD Keypad User Guides. NORTH AMERICA: FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications not expressly approved by GUARDALL could void the user's authority to operate this equipment. Canadian Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003. EUROPE: This equipment has been tested and found to comply with the CE directive and standards for ITE equipment used in commercial and heavy industrial applications.

Navigation menu