Guardall a division of CSG Security XLK1 LCD Keypad User Manual 2
Guardall, a division of CSG Security Corp LCD Keypad 2
Contents
- 1. User Manual 1
- 2. User Manual 2
User Manual 2
GUARDALL www.guardall.com | +1 877.249.9993 5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1 sales@ guardall.com +1 905.206.8434 | support@ guardall.com +1 905.206.8436 | Fax: +1 905.629.4970 xL LCD Keypad Installation Instructions 21-3610 rev1.4 The LCD keypad provides the ability to operate the entire Monitor xL™ or Chubb AFx™ system. It will also provide readouts of the status of the systems and location and nature of alarms. ypa Ke Module Point Assignment: 8 points. First point: Fire Alert buttons Second point: Panic (HoldUp) buttons Third point: Auxiliary Alert buttons Points 4 – 7 are hard wire inputs 1 – 4 on the Standard and G-ProxII version. Points 4 – 5 are hard wire inputs 1 – 2 on the Wiegand version. All unused points are skipped. XX 0V Future OUT Module Bus 1 2 +12V A Serial # sticker for programming into Module Programming. 0V Future Wiegand Reader Data 1 and 0. No reader LED connection. Te rm ina lB loc OUT Output 1 2 3 4 5 6 PT1 0V PT2 D1 0V D0 Ba ck Keypad Output goes negative. Interface with a relay or power Cable supply. Common their negatives with keypad 0V. Sonalert Terminal Block Tamper Spring After placing the keypad on its back section, make sure the keypad's securing screws (supplied) are always I N ! ComsLost #50624ef Enter code 24 822 ABC DEF GHI JKL MNO PRS TUV WXY Z_Q Point 2 Alert Labels Red Flashing: Green On Always Protection ON with power present. Solid: Partial protection (STAY) CSG SecurityCorp / Sécurité CSG Corp Wall tamper knock out Rectangular Conduit (Trunking) Red Green Yellow Point 1 Wiegand XX Keypad LEDs ,-# 1 2 +12V A Ke ypa Circuit board pin connectors insert into fixed terminal blocks on inside of keypad back. This allows the keypad to make wire connections in the terminal blocks. Apply dealer's logo label (supplied) in the indented space at the top of the keypad. Apply the Alert Button labels as required. Module Bus 1 2 3 4 5 6 PT1 0V PT2 PT3 0V PT4 Input 2 dF ron Standard and G-ProxII Common Flip Cover Keypad Terminal Block Wiring Input 1 Ratings: LCD Keypad with Reader Input: 12 – 13.8VDC, 110mA Output: 12VDC, 1x10mA Point LCD Keypad 4–7 Input: 12 – 13.8VDC, 95mA Output: 12VDC, 1x10mA Point Temp for both: -10°C to +55°C (14°F to 131°F) @ 4–5 93% Point 3 Yellow On when trouble condition present. Flashing when there is no AC mains. To use the keypad tamper spring as a wall tamper break out this plastic cylinder inside the back cover. Screw it to the wall, keeping it in the same hole as it was attached, so the back cover fits over it. The plastic cylinder prevents the spring from being affected by flat objects wedged in behind the keypad. The additional keypad base is optional. For installations using it there is a similar, shorter, washer style, plastic break out. Place it behind the plastic cylinder and screw them down together. Then place the holes in the base and keypad backing over top of them. Fit the spring inside the plastic cylinder part and secure the keypad front to the keypad back. The spring compressing should reset the keypad tamper condition. Knock outs for rectangular conduit using additional keypad base. Page 1 of 2 GUARDALL www.guardall.com | +1 877.249.9993 5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1 sales@ guardall.com +1 905.206.8434 | support@ guardall.com +1 905.206.8436 | Fax: +1 905.629.4970 21-3610 rev1.4 xL LCD Keypad Installation Instructions 3 Keypad Versions • LCD Keypad P/N 111-3610 (white), 111-3620 (gray): standard keypad includes 3 programmable alert button inputs, 4 hardwire alarm input points and 1 output point. • LCD Keypad with internal RF reader P/N 111-3611 (white), 111-3621(gray): keypad includes 3 programmable alert button inputs, 4 hardwire alarm input points and 1 output point. Includes a built-in RF G-Prox reader. • LCD with external Wiegand reader Keypad P/N 111-3612 (white), 111-3622 (gray): keypad includes the capability to connect an external Weigand reader to it. Keypad includes 3 programmable alert button inputs, 2 hardwire alarm input points and 1 output point. NOTE: – Double or triple card touch (badge) to LCD with external reader is the equivalent of hold a card (badge) feature at the LCD with internal reader to e.g. turn protection on and off. – GProxII and MIFARE readers have been proven to work acceptably when connected to the LCD with external reader. All versions • Communicate with the main control unit on the SNAPP module bus. • Backlit, 2x16 LCD display. • Colours: white, grey. For further keypad information, please see the Monitor xL™ or Chubb AFx™ Simplified or Advanced Installation and LCD Keypad User Guides. NORTH AMERICA: FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications not expressly approved by GUARDALL could void the user's authority to operate this equipment. Canadian Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003. EUROPE: This equipment has been tested and found to comply with the CE directive and standards for ITE equipment used in commercial and heavy industrial applications. CSG SecurityCorp / Sécurité CSG Corp Page 2 of 2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2010:08:03 13:43:54-04:00 Create Date : 2010:07:27 15:56:50-04:00 Metadata Date : 2010:08:03 13:43:54-04:00 Format : application/pdf Title : Creator : . Document ID : uuid:9bf34990-8643-4b64-86a6-4f885b12de31 Instance ID : uuid:ca60a9f5-c6ec-4dde-bc08-89a70f06d63a Page Count : 2 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools