HBC radiomatic TC64327 Transceiver Module User Manual Integration Manual

HBC-radiomatic GmbH Transceiver Module Integration Manual

Integration Manual

TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 1 of 13 Revision: 0 User manual Transceiver module TC643
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 2 of 13 Revision: 0 1 Table of Contents 1 Table of Contents.......................................................................................................................... 2 2 Information about the module...................................................................................................... 3 2.1 Intended use .......................................................................................................................... 3 2.2 Shielding provision of the RF part .......................................................................................... 3 2.3 Common installation guidelines ............................................................................................. 3 2.4 Specific installation instructions ............................................................................................. 3 2.5 FCC notes for the module ...................................................................................................... 4 2.5.1 Applied rules ................................................................................................................. 4 2.5.2 Modification of equipment ............................................................................................. 4 2.5.3 Dedicated antennas ...................................................................................................... 4 2.5.4 RF exposure information .............................................................................................. 5 2.6 Labelling of the module .......................................................................................................... 6 2.7 Technical data ....................................................................................................................... 7 3 Information for the end device ..................................................................................................... 8 3.1 Integration of the module ....................................................................................................... 8 3.2 Safety Instructions ................................................................................................................. 8 3.3 FCC notes for all host devices ............................................................................................... 9 3.3.1 Modification of equipment ............................................................................................. 9 3.3.2 Special accessories ...................................................................................................... 9 3.3.3 RF exposure evaluation ................................................................................................ 9 3.3.4 Simultaneous transmission ......................................................................................... 10 3.3.5 RF exposure statement .............................................................................................. 10 3.3.6 Labelling ..................................................................................................................... 11 3.4 FCC notes for a host subject to verification .......................................................................... 11 3.4.1 Modification of equipment ........................................................................................... 11 3.4.2 Information to the user ................................................................................................ 12 3.4.3 Special accessories .................................................................................................... 12 3.4.4 RF exposure evaluation .............................................................................................. 12 3.4.5 Simultaneous transmission ......................................................................................... 12 3.4.6 Labelling ..................................................................................................................... 12 3.5 FCC notes for a host subject to certification ......................................................................... 12 3.5.1 Modification of equipment ........................................................................................... 13 3.5.2 Special accessories .................................................................................................... 13 3.5.3 RF exposure evaluation .............................................................................................. 13 3.5.4 Simultaneous transmission ......................................................................................... 13 3.5.5 Labelling ..................................................................................................................... 13
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 3 of 13 Revision: 0 2 Information about the module 2.1 Intended use The TC643 is a transceiver for data transfer with fast transmit-receive switchover. The frequency range is 460.6500 to 461.5625 MHz, according to the hardware version for USA. This module is not sold separately, but is used for systems of HBC-radiomatic GmbH exclusively. 2.2 Shielding provision of the RF part The RF component has been designed in this way to comply with the requirements for modular transmitters and to avoid easy access to the RF components. Efficient shielding of RF part is achieved by means of metal shielding. The metal shielding is soldered up with the circuit board. 2.3 Common installation guidelines  Align module with connector and insert it with care.  Affix module with fixing screw.  Check proper installation. 2.4 Specific installation instructions For details about the installation of the module in a specific host appropriate “Instructions for modular transceiver installation” are supplied by HBC-radiomatic GmbH. Please refer to the document appropriate for the host to be assembled with the transmitter module.
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 4 of 13 Revision: 0 2.5 FCC notes for the module 2.5.1 Applied rules The TC643 transceiver module complies with the requirements of 47 CFR Part 90, §90.217. It uses frequencies of the Industrial/Business Radio Pool and is subject to licensing. 2.5.2 Modification of equipment Changes or modifications made to this equipment not expressly approved by HBC-radiomatic GmbH may void the FCC authorization to operate this equipment. 2.5.3 Dedicated antennas The TC643 transceiver module may only be used with antennas certified with the module or antennas of the same type with antenna gain not exceeding the certified values for this type. The list of antennas to be used with the TC643 transceiver module is shown below. Internal antennas: HBC part number Antenna type Frequency range Gain [dBi] Connector type HBC-radiomatic datasheet AA080004 λ/4 - antenna 405 – 480 MHz 2.15 MMCX male x AB047010 λ/4 - antenna 405 – 480 MHz 2.15 MMCX male x AB158010 short dipole antenna 405 – 480 MHz 2.15 MMCX male x
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 5 of 13 Revision: 0 External antennas: HBC part number Antenna type Frequency range Gain [dBi] Connector type Manufacturer datasheet 012-01-00007 shortened half-wave antenna 440 – 470 MHz 6.15 BNC male x AA020002 whip antenna 400 – 460 MHz 2.15 BNC male x AA020031 λ/4 whip antenna 410 – 470 MHz 2.15 Mini-Crimp x AA050002 omnidirectional antenna 406 – 470 MHz 2 N female x AA060007 λ/4 mobile whip antenna 430 – 470 MHz 2.15 Mini-Crimp x AA060015 dual frequency whip antenna 380 – 470 MHz 800 – 960 MHz 2.15 Mini-Crimp x AA060018 whip antenna 450 – 470 MHz 6.15 Mini-Crimp x AA060021 λ/4 mobile whip antenna 406 – 470 MHz 2.15 Mini-Crimp x 2.5.4 RF exposure information The TC643 transceiver module complies with the RF exposure standalone SAR test exclusion requirements for portable devices with a test separation distance of 6 mm, i. e. a minimum separation distance of at least 6 mm between the radiating part and the user or nearby persons has to be assured. For simultaneous transmission appropriate RF exposure evaluations have to be performed. Portable exposure host platform evaluation procedures can be applied only if all transmitters in the host devices support portable exposure conditions. Transmitters and modules approved f or use in the portable exposure host platform may be used for standalone operations in mobile exposure host platforms, without further equipment approval, only when the same identical transmitter and antenna required for portable device exposure conditions are used.
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 6 of 13 Revision: 0 2.6 Labelling of the module HBC label FCC-label
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 7 of 13 Revision: 0 2.7 Technical data Technical Specification Common data Module code TC64327_ Antenna MMCX socket Number of RF channels 16 Frequency range 460.6500 – 461.5625 MHz Channel spacing 12.5 kHz Deviation ±2.5 kHz Frequency stability ±2.5 ppm or less (-30 °C …+85 °C) Operating temperature range -30 °C … +80 °C Modulation 9k12F2D Switch-over time (RX – TX) < 1 ms Dimensions (49 x 34 x 19) mm Weight 26 g Transmitter specific data Parameter Min. Typ. Max. Unit Supply voltage 3.3 4.2 4.6 V Parameter Min. Typ. Max. Unit Conducted output power - < 14 - dBm Adjacent channel power (25 kHz) - < -37 - dBm Spurious emission (80 MHz to1 GHz) - < -37 - dBm Spurious emission (47 MHz to 74 MHz) - < -57 - dBm Spurious emission (87.5 MHz to 118 MHz) - < -57 - dBm Spurious emission (174 MHz to 230 MHz) - < -57 - dBm Spurious emission (470 MHz to 862 MHz) - < -57 - dBm Spurious emission (> 1 GHz) - < -50 - dBm Supply current 110 115 120 mA Receiver specific data Parameter Min. Typ. Max. Unit Supply voltage 3.3 4.2 4.6 V Sensitivity @ 20 dB S/N and 8 kHz bandwidth -107 -108 -111 dBm Adjacent channel selectivity (12.5 kHz) 37 38 40 dB Spurious radiation (all) - < -57 - dBm Blocking (±2 MHz) 85 86 87 dB Blocking (±10 MHz) 95 96 97 dB Supply current 50 55 60 mA
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 8 of 13 Revision: 0 3 Information for the end device 3.1 Integration of the module As the TC643 transceiver module can be mounted in various hosts subject to different authorization procedures only the most typical combinations are covered by this user manual. If the host device is subject to other authorization procedures than described below the appropriate requirements of these authorization procedures apply. For details about the installation of the module in a specific host appropriate “Instructions for modular transceiver installation” are supplied by HBC-radiomatic GmbH. Please refer to the document appropriate for the host to be assembled with the module. This document also contains information about labelling and notices to the user. 3.2 Safety Instructions In customer related documents of the end product like instruction manuals, installation guides etc. appropriate safety instructions have to be included. The supplier of the complete system is responsible for these safety instructions.
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 9 of 13 Revision: 0 3.3 FCC notes for all host devices The information in this section applies to all hosts irrespective of the authorization procedure applicable to the host. The integrator is responsible for the final compliance of the end product including this certified transmitter module. Section §15.101 of 47 CFR Part 15 gives guidance in terms of applicable equipment authorization procedures of different end devices. Typically compliance to subpart 15 B (§15.107 and 15.109) Class A or B (spurious emissions up to 5th harmonic of the maximum of the highest frequency generated or used and the fundamental frequency of the module) including verification of the subpart 15 C compliance (field strength of fundamental and out-of-band emissions up to 10th harmonic of the fundamental frequency of the module) of the transmitter parameters apply. For details about the frequency range of radiated measurements see section §15.33. As the module is used for systems of HBC-radiomatic GmbH exclusively, two different authorization procedures for the end device are intended to be applied:  Verification (see section 3.4)  Certification (see section 3.5) 3.3.1 Modification of equipment The instruction manual of the host shall include the following statement: Changes or modifications made to this equipment not expressly approved by the party responsible for compliance may void the FCC authorization to operate this equipment. 3.3.2 Special accessories Where special accessories such as shielded cables and/or special connectors are required to comply with the emission limits, the instruction manual shall include appropriate instructions on the first page of the text describing the installation of the device. 3.3.3 RF exposure evaluation The TC643 transceiver module complies with the RF exposure standalone SAR test exclusion requirements for portable devices with a test separation distance of 6 mm, i. e. a minimum
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 10 of 13 Revision: 0 separation distance of at least 6 mm between the radiating part and the user or nearby persons has to be assured. For simultaneous transmission (e. g. if more than one module is assembled) appropriate RF exposure evaluations have to be performed. 3.3.4 Simultaneous transmission When the host product supports simultaneous-transmission operations the host manufacturer needs to check if there are additional RF exposure filing requirements due to the simultaneous transmissions. When additional application filing for RF exposure compliance demonstration is not required (e. g. if the TC643 transceiver module in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without any filing, using reasonable engineering judgment and testing for confirming compliance with out-of-band, restricted band, and spurious emission requirements in the simultaneous-transmission operating modes. If additional filing is required please contact the person at HBC-radiomatic GmbH responsible for certification of the TC643 transceiver module. 3.3.5 RF exposure statement After having performed an RF exposure evaluation including a check for simultaneous transmission, if applicable, the instruction manual of the host shall include the appropriate statement as noted below: a) For portable host devices: This device complies with the RF exposure SAR test exclusion requirements for portable devices if a minimum separation distance of 6 mm to its antennas and radiating structures is kept. In addition, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. b) For mobile or fixed host devices: This device complies with the RF exposure requirements for mobile or fixed host devices. However, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 11 of 13 Revision: 0 3.3.6 Labelling The host device shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the FCC identification number is not visible when the TC643 transceiver module is installed inside the host, then the outside of the device into which the module is installed must also display a label referring to the enclosed module: Contains FCC ID: NO9TC64327 3.4 FCC notes for a host subject to verification For a host device assembled with the TC643 transceiver module and subject to 47 CFR Part 15 verification of class A digital devices, the following statements have to be included in the user manual and the host device has to be labelled as noted below. If the host device is subject to other authorization procedures or parts the appropriate requirements of these authorization procedures or parts apply. 3.4.1 Modification of equipment See section 3.3.1.
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 12 of 13 Revision: 0 3.4.2 Information to the user NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 3.4.3 Special accessories See section 3.3.2. 3.4.4 RF exposure evaluation See section 3.3.3. 3.4.5 Simultaneous transmission See section 3.3.4. 3.4.6 Labelling See section 3.3.6. 3.5 FCC notes for a host subject to certification If the host additionally has radio parts inside for its own it is subject to certification. For a host device assembled with the TC643 transceiver module and subject to 47 CFR Part 15 certification, the following statements have to be included in the user manual and the host device
TC643 User manual HBC Issue date: 2017-02-17 Issued by: SEKH Page 13 of 13 Revision: 0 has to be labelled as noted below. If the host device is subject to other authorization procedures or parts the appropriate requirements of these authorization procedures or parts apply. 3.5.1 Modification of equipment See section 3.3.1. 3.5.2 Special accessories See section 3.3.2. 3.5.3 RF exposure evaluation See section 3.3.3. 3.5.4 Simultaneous transmission See section 3.3.4. 3.5.5 Labelling In addition to the labelling requirements as described in section 3.3.6, the host device must also be labelled with the FCC Identifier (FCC ID) of its own certification: FCC ID XZZYYNNNNN

Navigation menu