HBC radiomatic TC64327 Transceiver Module User Manual Integration Manual

HBC-radiomatic GmbH Transceiver Module Integration Manual

Integration Manual

Download: HBC radiomatic TC64327 Transceiver Module User Manual Integration Manual
Mirror Download [FCC.gov]HBC radiomatic TC64327 Transceiver Module User Manual Integration Manual
Document ID3305769
Application IDKqzjm12HSmBN4NsLXjLNUw==
Document DescriptionIntegration Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize28.73kB (359092 bits)
Date Submitted2017-03-07 00:00:00
Date Available2017-03-07 00:00:00
Creation Date2017-02-19 10:39:07
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2017-02-19 10:39:07
Document TitleIntegration Manual
Document CreatorMicrosoft® Word 2010

TC643
User manual
HBC
User manual
Transceiver module TC643
Issue date: 2017-02-17
Issued by: SEKH
Page 1 of 13
Revision: 0
TC643
User manual
HBC
1 Table of Contents
Table of Contents.......................................................................................................................... 2
Information about the module...................................................................................................... 3
2.1
2.2
Intended use .......................................................................................................................... 3
Shielding provision of the RF part .......................................................................................... 3
2.3
Common installation guidelines ............................................................................................. 3
2.4
Specific installation instructions ............................................................................................. 3
2.5
FCC notes for the module ...................................................................................................... 4
2.5.1
Applied rules ................................................................................................................. 4
2.5.2
Modification of equipment ............................................................................................. 4
2.5.3
Dedicated antennas ...................................................................................................... 4
2.5.4
RF exposure information .............................................................................................. 5
2.6
Labelling of the module .......................................................................................................... 6
2.7
Technical data ....................................................................................................................... 7
Information for the end device ..................................................................................................... 8
3.1
3.2
Integration of the module ....................................................................................................... 8
Safety Instructions ................................................................................................................. 8
3.3
FCC notes for all host devices ............................................................................................... 9
3.3.1
Modification of equipment ............................................................................................. 9
3.3.2
Special accessories ...................................................................................................... 9
3.3.3
RF exposure evaluation ................................................................................................ 9
3.3.4
Simultaneous transmission ......................................................................................... 10
3.3.5
RF exposure statement .............................................................................................. 10
3.3.6
Labelling ..................................................................................................................... 11
3.4
FCC notes for a host subject to verification .......................................................................... 11
3.4.1
Modification of equipment ........................................................................................... 11
3.4.2
Information to the user ................................................................................................ 12
3.4.3
Special accessories .................................................................................................... 12
3.4.4
RF exposure evaluation .............................................................................................. 12
3.4.5
Simultaneous transmission ......................................................................................... 12
3.4.6
Labelling ..................................................................................................................... 12
3.5
FCC notes for a host subject to certification ......................................................................... 12
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
Modification of equipment ........................................................................................... 13
Special accessories .................................................................................................... 13
RF exposure evaluation .............................................................................................. 13
Simultaneous transmission ......................................................................................... 13
Labelling ..................................................................................................................... 13
Issue date: 2017-02-17
Issued by: SEKH
Page 2 of 13
Revision: 0
TC643
User manual
HBC
2 Information about the module
2.1
Intended use
The TC643 is a transceiver for data transfer with fast transmit-receive switchover. The frequency range
is 460.6500 to 461.5625 MHz, according to the hardware version for USA. This module is not sold
separately, but is used for systems of HBC-radiomatic GmbH exclusively.
2.2
Shielding provision of the RF part
The RF component has been designed in this way to comply with the requirements for modular
transmitters and to avoid easy access to the RF components. Efficient shielding of RF part is
achieved by means of metal shielding. The metal shielding is soldered up with the circuit board.
2.3
Common installation guidelines

Align module with connector and insert it with care.

Affix module with fixing screw.

Check proper installation.
2.4
Specific installation instructions
For details about the installation of the module in a specific host appropriate “Instructions for
modular transceiver installation” are supplied by HBC-radiomatic GmbH. Please refer to the
document appropriate for the host to be assembled with the transmitter module.
Issue date: 2017-02-17
Issued by: SEKH
Page 3 of 13
Revision: 0
TC643
2.5
HBC
User manual
FCC notes for the module
2.5.1
Applied rules
The TC643 transceiver module complies with the requirements of 47 CFR Part 90, §90.217. It
uses frequencies of the Industrial/Business Radio Pool and is subject to licensing.
2.5.2
Modification of equipment
Changes or modifications made to this equipment not expressly approved by HBC-radiomatic
GmbH may void the FCC authorization to operate this equipment.
2.5.3
Dedicated antennas
The TC643 transceiver module may only be used with antennas certified with the module or
antennas of the same type with antenna gain not exceeding the certified values for this type.
The list of antennas to be used with the TC643 transceiver module is shown below.
Internal antennas:
HBC part number
Antenna type
Frequency range
Gain [dBi]
Connector type
HBCradiomatic
datasheet
AA080004
λ/4 - antenna
405 – 480 MHz
2.15
MMCX male
AB047010
λ/4 - antenna
405 – 480 MHz
2.15
MMCX male
AB158010
short dipole antenna
405 – 480 MHz
2.15
MMCX male
Issue date: 2017-02-17
Issued by: SEKH
Page 4 of 13
Revision: 0
TC643
HBC
User manual
External antennas:
HBC part number
Antenna type
Frequency range
Gain [dBi]
Connector type
Manufacturer
datasheet
012-01-00007
shortened half-wave
antenna
440 – 470 MHz
6.15
BNC male
AA020002
whip antenna
400 – 460 MHz
2.15
BNC male
AA020031
λ/4 whip antenna
410 – 470 MHz
2.15
Mini-Crimp
AA050002
omnidirectional antenna
406 – 470 MHz
N female
AA060007
λ/4 mobile whip antenna
430 – 470 MHz
2.15
Mini-Crimp
AA060015
dual frequency whip
antenna
380 – 470 MHz
800 – 960 MHz
2.15
Mini-Crimp
AA060018
whip antenna
450 – 470 MHz
6.15
Mini-Crimp
AA060021
λ/4 mobile whip antenna
406 – 470 MHz
2.15
Mini-Crimp
2.5.4
RF exposure information
The TC643 transceiver module complies with the RF exposure standalone SAR test exclusion
requirements for portable devices with a test separation distance of 6 mm, i. e. a minimum
separation distance of at least 6 mm between the radiating part and the user or nearby persons
has to be assured.
For simultaneous transmission appropriate RF exposure evaluations have to be
performed.
Portable exposure host platform evaluation procedures can be applied only if all transmitters in
the host devices support portable exposure conditions. Transmitters and modules approved f or
use in the portable exposure host platform may be used for standalone operations in mobile
exposure host platforms, without further equipment approval, only when the same identical
transmitter and antenna required for portable device exposure conditions are used.
Issue date: 2017-02-17
Issued by: SEKH
Page 5 of 13
Revision: 0
TC643
2.6
HBC
User manual
Labelling of the module
HBC label
FCC-label
Issue date: 2017-02-17
Issued by: SEKH
Page 6 of 13
Revision: 0
TC643
2.7
HBC
User manual
Technical data
Technical Specification
Common data
Module code
Antenna
Number of RF channels
Frequency range
Channel spacing
Deviation
Frequency stability
Operating temperature range
Modulation
Switch-over time (RX – TX)
Dimensions
Weight
TC64327_
MMCX socket
16
460.6500 – 461.5625 MHz
12.5 kHz
±2.5 kHz
±2.5 ppm or less (-30 °C …+85 °C)
-30 °C … +80 °C
9k12F2D
< 1 ms
(49 x 34 x 19) mm
26 g
Transmitter specific data
Parameter
Supply voltage
Parameter
Conducted output power
Adjacent channel power (25 kHz)
Spurious emission (80 MHz to1 GHz)
Spurious emission (47 MHz to 74 MHz)
Spurious emission (87.5 MHz to 118 MHz)
Spurious emission (174 MHz to 230 MHz)
Spurious emission (470 MHz to 862 MHz)
Spurious emission (> 1 GHz)
Supply current
Receiver specific data
Parameter
Supply voltage
Sensitivity @ 20 dB S/N and 8 kHz bandwidth
Adjacent channel selectivity (12.5 kHz)
Spurious radiation (all)
Blocking (±2 MHz)
Blocking (±10 MHz)
Supply current
Issue date: 2017-02-17
Issued by: SEKH
Min.
3.3
Min.
110
Typ.
4.2
Typ.
< 14
< -37
< -37
< -57
< -57
< -57
< -57
< -50
115
Max.
4.6
Max.
120
Unit
Unit
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
mA
Min.
3.3
-107
37
85
95
50
Typ.
4.2
-108
38
< -57
86
96
55
Max.
4.6
-111
40
87
97
60
Unit
dBm
dB
dBm
dB
dB
mA
Page 7 of 13
Revision: 0
TC643
User manual
HBC
3 Information for the end device
3.1
Integration of the module
As the TC643 transceiver module can be mounted in various hosts subject to different authorization
procedures only the most typical combinations are covered by this user manual. If the host device is
subject to other authorization procedures than described below the appropriate requirements of these
authorization procedures apply.
For details about the installation of the module in a specific host appropriate “Instructions for modular
transceiver installation” are supplied by HBC-radiomatic GmbH. Please refer to the document
appropriate for the host to be assembled with the module. This document also contains information
about labelling and notices to the user.
3.2
Safety Instructions
In customer related documents of the end product like instruction manuals, installation guides etc.
appropriate safety instructions have to be included. The supplier of the complete system is responsible
for these safety instructions.
Issue date: 2017-02-17
Issued by: SEKH
Page 8 of 13
Revision: 0
TC643
3.3
User manual
HBC
FCC notes for all host devices
The information in this section applies to all hosts irrespective of the authorization procedure applicable
to the host.
The integrator is responsible for the final compliance of the end product including this certified transmitter
module. Section §15.101 of 47 CFR Part 15 gives guidance in terms of applicable equipment
authorization procedures of different end devices. Typically compliance to subpart 15 B (§15.107 and
15.109) Class A or B (spurious emissions up to 5th harmonic of the maximum of the highest frequency
generated or used and the fundamental frequency of the module) including verification of the subpart
15 C compliance (field strength of fundamental and out-of-band emissions up to 10th harmonic of the
fundamental frequency of the module) of the transmitter parameters apply. For details about the
frequency range of radiated measurements see section §15.33.
As the module is used for systems of HBC-radiomatic GmbH exclusively, two different authorization
procedures for the end device are intended to be applied:

Verification (see section 3.4)

Certification (see section 3.5)
3.3.1
Modification of equipment
The instruction manual of the host shall include the following statement:
Changes or modifications made to this equipment not expressly approved by the party
responsible for compliance may void the FCC authorization to operate this equipment.
3.3.2
Special accessories
Where special accessories such as shielded cables and/or special connectors are required to
comply with the emission limits, the instruction manual shall include appropriate instructions on
the first page of the text describing the installation of the device.
3.3.3
RF exposure evaluation
The TC643 transceiver module complies with the RF exposure standalone SAR test exclusion
requirements for portable devices with a test separation distance of 6 mm, i. e. a minimum
Issue date: 2017-02-17
Issued by: SEKH
Page 9 of 13
Revision: 0
TC643
User manual
HBC
separation distance of at least 6 mm between the radiating part and the user or nearby persons
has to be assured.
For simultaneous transmission (e. g. if more than one module is assembled) appropriate
RF exposure evaluations have to be performed.
3.3.4
Simultaneous transmission
When the host product supports simultaneous-transmission operations the host manufacturer
needs to check if there are additional RF exposure filing requirements due to the simultaneous
transmissions. When additional application filing for RF exposure compliance demonstration is
not required (e. g. if the TC643 transceiver module in combination with all simultaneously
operating transmitters complies with the RF exposure simultaneous transmission SAR test
exclusion requirements), the host manufacturer may do his own evaluation without any filing,
using reasonable engineering judgment and testing for confirming compliance with out -of-band,
restricted band, and spurious emission requirements in the simultaneous -transmission operating
modes.
If additional filing is required please contact the person at HBC-radiomatic GmbH responsible for
certification of the TC643 transceiver module.
3.3.5
RF exposure statement
After having performed an RF exposure evaluation including a check for simultaneous transmission, if
applicable, the instruction manual of the host shall include the appropriate statement as noted below:
a) For portable host devices:
This device complies with the RF exposure SAR test exclusion requirements for portable devices
if a minimum separation distance of 6 mm to its antennas and radiating structures is kept. In
addition, the device shall be used in such a manner that the potential for human contact during
normal operation is minimized.
b) For mobile or fixed host devices:
This device complies with the RF exposure requirements for mobile or fixed host devices.
However, the device shall be used in such a manner that the potential for human contact during
normal operation is minimized.
Issue date: 2017-02-17
Issued by: SEKH
Page 10 of 13
Revision: 0
TC643
3.3.6
User manual
HBC
Labelling
The host device shall bear the following statement in a conspicuous location on the device:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
If the FCC identification number is not visible when the TC643 transceiver module is installed inside the
host, then the outside of the device into which the module is installed must also display a label referring
to the enclosed module:
Contains FCC ID: NO9TC64327
3.4
FCC notes for a host subject to verification
For a host device assembled with the TC643 transceiver module and subject to 47 CFR Part 15
verification of class A digital devices, the following statements have to be included in the user
manual and the host device has to be labelled as noted below. If the host device is subject to
other authorization procedures or parts the appropriate requirements of these authorization
procedures or parts apply.
3.4.1
Modification of equipment
See section 3.3.1.
Issue date: 2017-02-17
Issued by: SEKH
Page 11 of 13
Revision: 0
TC643
3.4.2
User manual
HBC
Information to the user
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
3.4.3
Special accessories
See section 3.3.2.
3.4.4
RF exposure evaluation
See section 3.3.3.
3.4.5
Simultaneous transmission
See section 3.3.4.
3.4.6
Labelling
See section 3.3.6.
3.5
FCC notes for a host subject to certification
If the host additionally has radio parts inside for its own it is subject to certification. For a host
device assembled with the TC643 transceiver module and subject to 47 CFR Part 15
certification, the following statements have to be included in the user manual and the host device
Issue date: 2017-02-17
Issued by: SEKH
Page 12 of 13
Revision: 0
TC643
User manual
HBC
has to be labelled as noted below. If the host device is subject to other authorization procedures
or parts the appropriate requirements of these authorization procedures or parts apply.
3.5.1
Modification of equipment
See section 3.3.1.
3.5.2
Special accessories
See section 3.3.2.
3.5.3
RF exposure evaluation
See section 3.3.3.
3.5.4
Simultaneous transmission
See section 3.3.4.
3.5.5
Labelling
In addition to the labelling requirements as described in section 3.3.6, the host device must also be
labelled with the FCC Identifier (FCC ID) of its own certification:
FCC ID XZZYYNNNNN
Issue date: 2017-02-17
Issued by: SEKH
Page 13 of 13
Revision: 0

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 13
Language                        : de-DE
Producer                        : Microsoft® Word 2010
Creator                         : Microsoft® Word 2010
Create Date                     : 2017:02:19 10:39:07+01:00
Modify Date                     : 2017:02:19 10:39:07+01:00
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NO9TC64327

Navigation menu