HID Global 0006A Proximity Reader User Manual 5365 910 manual
HID Global Corporation Proximity Reader 5365 910 manual
Contents
- 1. 5365 910 manual
- 2. 5395 902 manual
- 3. 6005 910 manual
5365 910 manual
REV DESCRIPTION DATE INITIAL RELEASE PER EO #E5365-44 APPROVED -01 Part: Sheets 1 through 4 -02 Part: Sheets 1 through 5 NOTE: Cover sheet is for Revision Control only, and is not to be sent with document. REV SHEET 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 59 50 51 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 REV STATUS OF SHEETS 10 11 12 13 14 15 REV SHEET TOLERANCES APPROVALS .XX = +/- .03” DWN Andresky .XXX = +/- .010” CHK ANGLES = +/- 1° APVD MATERIAL N/A APVD FINISH N/A SCALE N/A DATE HID CORPORATION 060500 IRVINE, CALIFORNIA THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION. IT MAY NOT BE DISCLOSED TO OTHERS OR USED FOR MANUFACTURING PURPOSES WITHOUT THE PERMISSION OF HID CORPORATION. Installation Manual, Miniprox Reader P/N SIZE 5365-910 REV 1 SHEET 0 OF 5 Install Manual – 5365-910 Rev 1 MiniproxTM Installation Manual _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1 PARTS LIST (Included) Quantity Connecting the Reader to the Host TM - Miniprox Reader with snap-on cover and 18” cable (For terminal block versions no cable is supplied) - #6-32 x 1” self-tapping panhead screw - Installation manual - Junction box (Hazardous installation version only) PARTS LIST (Not-Included) Quantity - Wire splice - DC Power supply 5.0 VDC or 12 VDC Mounting Instructions • Determine an appropriate mounting location. The reader may be mounted to any surface, including metal. • Drill two (2) 3/32-inch (2.5mm) holes approximately 1 inch deep for mounting the reader. • Drill a 5/8-inch (16mm) hole for the cable. • Remove the snap-on cover from the reader and secure the reader to the mounting surface. • Route the cable from the reader and/or power supply to the host. A linear type power supply is recommended. Check all electrical codes for proper cable installation. • For best operation, the drain wire should be disconnected at the power supply end of the cables. • For the cable connection to the Panel - Use Alpha #1299C or equivalent. • Test the operation of the reader. After completion of the test, replace the snap-on cover. • See sheet 3 of this manual for the appropriate dimensioned drawings. Connect the reader to the host according to the wiring table below and the host installation guide. Wiegand Clock & Data Wire Color Terminal Number +DC +DC Red TB1-1 Ground Ground Black TB1-2 Data0 Data Green TB1-3 Data1 Clock White TB1-4 Shield Ground Shield Ground Drain TB1-5 Green LED Green LED Orange TB1-6 Red LED Red LED Brown TB1-7 Beeper Beeper Yellow TB1-8 _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1 Hold Hold Blue TB1-9 --Card Present Violet TB1-10 Testing and Operation • When power is applied to the reader the LED will flash green three (3) times while the beeper beeps simultaneously. The LED will then turn red. This indicates that the microcontroller is operating properly. • Present an ID card to the reader. The LED will momentarily turn green while the beeper beeps once, indicating that the card was read successfully. Important Product Specifications Power requirements (linear supply) Operating Voltage Range 5.0 – 16.0 VDC Absolute Maximum Voltage 18 VDC Peak Current 80 Ma Average Current 5V or 12V 20 Ma Maximum cable distance To host 500 ft (153 m) FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1 Pigtail Installation Figure 1 _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1 Terminal Block Installation Figure 2 _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1 Hazardous Location Installation (Pigtail or Terminal Block) Figure 3 _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - Miniprox Installation Manual 5365-910 Rev 1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2000:09:22 16:52:09 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2000:09:22 16:52:10-04:00 Page Count : 7EXIF Metadata provided by EXIF.tools