HID Global 607XA 6074A HID MIFARE Wiegand Reader User Manual 474681

Download:
Mirror Download [FCC.gov]
Document ID	474681
Application ID	WtcZtMkStjXavzy4ayyJmg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	14.05kB (175617 bits)
Date Submitted	2004-09-30 00:00:00
Date Available	2004-09-30 00:00:00
Creation Date	2004-09-30 15:07:42
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-09-30 15:07:42
Document Title	Microsoft Word - 474681.DOC
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

REV
DESCRIPTION
DATE
6074A INITIAL RELEASE
ADDED FCC STATEMENT, FIX LED INPUT
APPROVED
NOTE: Cover sheet is for Revision Control only, and is not to be sent with document.
REV
SHEET
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
REV STATUS
OF SHEETS
10
11
12
13
14
15
REV
SHEET
TOLERANCES
APPROVALS
DATE
HID CORPORATION
.XX = +/- .03”
IRVINE, CALIFORNIA
.XXX = +/- .010”
Installation Manual
ANGLES = +/- 1°
MIFARE® WIEGAND Reader
MATERIAL N/A
FINISH N/A
P/N
SCALE N/A
SIZE
6074-901
REV 2
SHEET 0 OF 6
Installation Manual – 6074-901 Rev A
HID MIFARE WIEGAND READER 6074A
____________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-7769 FAX (714) 598-1690
1 of 5
Web page, E-mail - www.prox.com MIFARE Wiegand Reader Installation Manual 6074-901 REV 2

MIFARE WIEGAND Reader Installation Manual
System Overview
The MIFARE Wiegand Reader is a self contained proximity Reader, frequently used in Access Control
Systems. The antenna and all associated electronics are assembled in a polycarbonate housing. The
Reader contains a micro-controller unit that controls an RF field that is generated at 13.56MHz. The
Reader has a sensitive receiver circuit that detects ID card data and passes it along to the microcontroller for decoding. The Reader output is configured in the "Wiegand" style electrical interface for
model 6074A. The Reader has a single Bicolor LED that will emit red, green or amber colors. Installation
of the MIFARE Wiegand Reader consists of mounting the Reader and connecting the cable to the Host
via the Pigtail.
Operation
Access Cards are to be presented to the front of the Reader. The LED is red when ready to read an ID
card. The LED turns green when the card is read and a message is transmitted to the Host computer or
interface panel. When the system is ready for another card, the LED returns to red. The LED is flashed
green and the Beeper is activated for 500 milliseconds when they are controlled by the internal microcontroller. The operation of the LED and beeper is often controlled by the Host panel. If Host controlled,
the operation will deviate from Host to Host. The MIFARE Wiegand reader’s default configuration can
accept green and beeper input control lines that allows control of green LED and beeper only (Red input
is not supported).
Parts List
1) MIFARE Wiegand Reader
2) #6-32 x 1" self tapping, Type T or 23
3) This Installation Sheet
4) Wire Splice
5) Grommet
6) DC Power Supply 10.0 to 14.0VDC, 50mA
7) Cable, 9 conductor , 22 AWG
Quantity
1 (included)
2 (included)
1 (included)
9 (installer supplied)
1 Recommended (installer supplied)
1 (installer supplied)
Up to 500ft. (installer supplied) Alpha 1295C
See Cable Notes
Installation Procedure:
1. Determine an appropriate mounting position for the Reader. Drill two 7/64th (.109) Inch holes for
mounting the Reader to the surface (see figure 1). Drill a 3/8 to 1.0 Inch hole for the cable. Place a
grommet around the edge of the hole. Route the interface cable from the Reader and/or power
supply to the Host. Check all electrical codes for proper cable installation.
2. The MIFARE Wiegand Reader is a Pigtail style with a 18” - 9 conductor cable. Prepare the new
cable by cutting the cable jacket back 1-1/4” and strip the wires ¼”. Splice the cable and the pigtail
together and seal the splice. Trim and cover all conductors that are not used.
3. Connect the Reader and Host together according to the wiring diagram with figure 2 and the Host
installation guide. The legend for wiring is color coded (according to the "Wiegand Standard") for the
recommended cable.
4. After wiring the Reader and power supply, the Reader is ready to be tested. Power up the Reader
and the red LED will be on when operating under the factory default reader configuration. This
indicates that the micro-controller unit is working properly. Present an ID card to the Reader and the
LED should momentarily turn green, indicating a read of the card. If the Reader LED is controlled by
the Host refer to the Host description of the LED operation.
5. Mount the Reader with the provided screws when mounting onto metal mullions or junction boxes.
On other materials use the appropriate fastener.
____________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-7769 FAX (714) 598-1690
2 of 5
Web page, E-mail - www.prox.com MIFARE Wiegand Reader Installation Manual 6074-901 REV 2
Dimension Diagrams, front, side and back views
FIGURE 1
Wire Connections
10
+DC
Ground
Data0
Data1
---
Green
White
Red
LED
Brown
---
Black
Green
LED
Orange
Beeper
Red
Shield
Ground
Drain
Yellow
---
---
FIGURE 2
Cable Notes
1) Wiegand - +DC, Ground, Shield Ground, Data0 and Data1 are required for Wiegand Operation. All
others (Green LED, Red LED, and Beeper) are optional.
2) When using a separate power supply for the MIFARE Wiegand Reader, the power supply and Host
should have a common ground (voltage reference).
3) If the Host is controlling the beeper or the LEDs are configured for the external LED mode, additional
conductors will be required. The recommended cables are Alpha 1295C, 1296C, 1297C, 1298C and
1299C, which are five, six, seven, eight and nine conductors respectively. Larger wire gauges are
acceptable. The wire is to be stranded with an overall foil shield plus the drain wire.
4) The Cable shield (drain) should be connected to the earth ground at the panel or power supply end of
the cable. Also, for emissions compliance, tie earth ground and common together at the power supply.
This configuration is the best for shielding the reader cable from external interference and reducing the
likelihood of the Reader causing interference. Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
____________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-7769 FAX (714) 598-1690
3 of 5
Web page, E-mail - www.prox.com MIFARE Wiegand Reader Installation Manual 6074-901 REV 2
Testing and Operation
When power is applied to the reader the LED will turn – on Red. This indicates that the microcontroller is
operating properly. Present an ID card to the reader. The LED will momentarily turn green while the
beeper beeps once, indicating that the card was read successfully. In normal operation, the Red LED is
normally on and the Green LED flashes on a valid card read. The Green LED and Beeper respond when
their respective user input line is pulled low. There is no operation for the Red LED user input.
Please note that typical read range for MIFARE cards is 1.5 – 2.0” (37-50 mm).
Card Compatibility
The HID MIFARE Reader reads serial number data from these cards: HID MIFARE, Any Philips
compatible MIFARE Standard contactless smart card. The reader will read the MIFARE Card Serial
Number only from all MIFARE cards, including MIFARE Lite and MIFARE Pro cards.
*The HID MIFARE reader will not read 125 kHz HID Proximity cards.
CSN Read Only Mode
In CSN Only mode, the reader reads the 32-bit MIFARE random card serial number (CSN or UID) from
any MIFARE card, including MIFARE Lite, MIFARE Standard and MIFARE Pro, outputting that data
in a 40-bit Wiegand format - 32-bit CSN + 8 bit checksum format.
Sector Read Only Mode
In Sector Read Only Mode the reader reads and outputs a specified number of bits from a specified
sector based on reader configuration. The following reader attributes can be configured at the factory to
meet individual needs.
•
•
•
•
•
•
Application sector (0 – 15)
Application Block (0-2)
Sector Key
Number of Bits Output (1-128)
Starting Bit Number (0-127)
Audio/Visual feedback (ON/Off)
Product Configuration/Ordering Options
6074 A X
X XX -XXXX Y
Customer Custom Artwork or Firmware Number - 1 through 9, A
through Z
Customer Custom Number
Configuration Options - (00 standard)
Standard Hardware Options - P = Pigtail
Color - G = Gray
Current Revision Letter
Model Number 6074 = MIFARE Wiegand
¾
Standard Wiegand Part Number = 6074AGP00 is a MIFARE Wiegand, Gray Standard (1”)
housing, Potted, with 9 conductor, 18” Pigtail.
____________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-7769 FAX (714) 598-1690
4 of 5
Web page, E-mail - www.prox.com MIFARE Wiegand Reader Installation Manual 6074-901 REV 2
Product Specifications
Read Distance
¾ Overall Operating Limits (10VDC - minimum)
¾ Non-Metallic Mounting (12VDC - typical)
¾ Mounted on Metal (12VDC - typical)
1.0-1.5 inches (2.5-3.8 cm)
1.0-1.5 inches (2.5-3.8 cm)
1.0-2.5 inches (2.5-3.8 cm)
Environmental Characteristics
¾ Operating Temperature Range
¾ Storage Temperature Range
¾ Operating Humidity Range
¾ Operating Vibration Limit
¾ Operating Shock Limit
¾ Potting Material
¾ Enclosure Material
¾ Potted Weight
-30oC to 65oC (-22oF to 150oF)
-40oC to 85oC (-40oF to 185oF)
5% to 95% non-condensing
.04 g2/Hz 20-2000Hz
30g, 11mS, Half Sine
UL Recognized Filled Polyurethane
UL Recognized Lexan Polycarbonate
8.2oz (228grms)
Power Requirements
¾ Power supply
¾ Operating Voltage Range (+DC)
¾ Absolute Maximum (+DC non-operating)
¾ Maximum Average Current at 12V
¾ Transient Protection (all terminals)
¾ Reverse Voltage Protection
¾ Input Voltage (maximum data-0/1 lines)
¾ Input Voltage (maximum interface lines)
Linear type recommended
10.0VDC -14.0VDC
14.0VDC
60mA
8,000 volts
-15V on all I/O and -35 for power lines
15.0VDC
15.0VDC
Operating Parameters
¾ Excitation Frequency
¾ Read and Report Speed (26 bit Wiegand Card)
¾ Maximum Cable Distance to Host
¾ LED Type
¾ LED Operation (host control of red/green)
¾ Beeper Operation (host control)
¾ Beeper Control (default)
13.56MHz
200mS (1K card) + output data
500 feet (152 meters)
Bi-colored Red/Green
.5V on LED control line
.5V on beeper line
Beeper enabled
FCC Compliance Statement:
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: THE ABOVE ARE RECOMMENDED INSTALLATION PROCEDURES. ALL LOCAL, STATE
AND NATIONAL ELECTRICAL CODES TAKE PRECEDENCE.
____________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (714) 598-1600 (800) 237-7769 FAX (714) 598-1690
2 of 5
Web page, E-mail - www.prox.com MIFARE Wiegand Reader Installation Manual 6074-901 REV 2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2004:09:30 15:07:42-04:00
Modify Date                     : 2004:09:30 15:07:42-04:00
Page Count                      : 6
Creation Date                   : 2004:09:30 19:07:42Z
Mod Date                        : 2004:09:30 19:07:42Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Administrator
Metadata Date                   : 2004:09:30 19:07:42Z
Creator                         : Administrator
Title                           : Microsoft Word - 474681.DOC

EXIF Metadata provided by EXIF.tools