HID Global SDC1000 Door Access Controller User Manual SDC1000 MANUAL
HID Global Corporation Door Access Controller SDC1000 MANUAL
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 136101 |
| Application ID | jgiCbZF4pOvsB2XaFBI//A== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 58.12kB (726524 bits) |
| Date Submitted | 2001-02-12 00:00:00 |
| Date Available | 2001-04-10 00:00:00 |
| Creation Date | 0000-00-00 00:00:00 |
| Producing Software | Acrobat PDFWriter 3.0 for Windows |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | SDC1000_MANUAL.PDF |
| Document Creator | Microsoft Word |
| Document Author: | Unknown |
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER OPERATING MANUAL MOTOROLA SDC1000 -1- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER CONTENTS 1. Important Safety Instructions 2. General 3. Features 4. Specifications 5. Name of the Parts 6. Identifying supplied parts 7. Installation of the Product 8. Wire Color Table of the Main Unit 9. Wire Connection in of basic application 10. Initial Setup 11. Operation 12. Setting Changes 13. FCC REGISTRATION INFORMATION 14. Warranty and Service -2- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 1. Important Safety Instructions When using your door access controller, basing safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product 3. Do not use liquid cleaners, or aerosol cleaners. Use a damp cloth for cleaning. if necessary, use a mild soap. 4. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 5. This product should be operated only from the type of power source indicated on the marking label. if you are not sure of the type of power supply to your home, consult your dealer or local power company. 6. Never push objects of any kind into this product though the cabinet slots as they may touch voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 7. To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified serviceman when some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. incorrect reassembly can cause electric shock when the appliance is subsequently used. 8. Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled into the product c. If the product has exposed to rain or water. d. If the product doses not operate normally by following the operating instructions. Adjust only those controls, that are covered by the operating instructions. Improper adjustment of other controls in damage and will often require extensive work by a qualified technician to restore the to normal operation. e. If the product exhibit a distinct change in performance. 2. General SDC1000 is an intelligent one door Access Controller based on powerful 8 bit Microprocessor to meet a simple and cost-effective access control market requirement. User friendly device allows you to register max. 128 USER IDs and easy to add or delete USER RFIDs. There are 5 inputs to connect EXIT Button, door contact, PIR sensor , Fire sensor and extra and you can program related output sources and activate timing from the front keypads. System will make alarm in case of number of times wrong entry and Temper switch opens and one TTL output can be connected to Auto-dialer (option) will make a call to the pre-defined phone numbers (max 4ch) and report the alarm to Police, Fire station and/or to your cellular phone by voice message. All event transaction report to the computer by RS232C communication. The modern design and easy installation will provide you an accurate access control for single door and 3 LED indicators informs you all system operating at real time. SDC1000 will give you field proven reliability and cost-effective solution anywhere the access controls and high security is required. 3. Features - One door Access Controller - Powerful dual 8 bit Microprocessors - Built-in 4” Proximity Reader - 128 USER Access RFIDs including one Master RFID - Independant 5 inputs and 4 outputs including 2 output Relays - All I/Os and activating Times user front programmable - Door Lock and Unlock function - Setting for Safe/Secure mode - Numbers of Try-out error Alarm - RS232 communication port for remote control and events report - 3 LEDs for system operation status - Modern design and easy operation -3- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 4. Specification .CPU .Memory .User PIN numbers .Proximity Reader .Input/Output .Communication .Keypads .LED .Power .Operating Environment .Reset : Dual 8 bit Microprocessors : 8 KB Program memory 512 bytes Flash memory : 128 User RFIDs including one Master RFID : Built-in 4” Proximity reader : 5 Inputs max. rating at DC 12V/20mA : 2 Relay outputs : DC12V/2A : 1 chime bell output : 5V/150mA , : 1 TTL output : 5V/20mA : One RS232C port, 9600 Baud Rate,N,8,1 : 12 Numeric Keypads : 3 LEDs(RED, GREEN, YELLOW) : DC 12V/ 200mA : 0°C to +60°C, 10% to 90% Humidity : Power ON Reset 5. Name of each part SDC1000 Main Unit 6. Identifying supplied parts Please unpack and check the contents of the box. Main Unit (1 EA) Wall Mount (1 EA) O-Ring (5 EA) Instructions (1 EA) -4- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 7. Installation of the Product 7-1. Drill two 6-32 holes and one 1/2" hole on the proper location of the wall. (If the gang box is already installed on the wall then skip this step.) 7-2. Using 2 screws, install wall mount to the wall. 7-3. Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit through the center hole and push the main unit to wall mount to lock the main unit and make sure that the main unit is locked with wall mount. * CAUTIONS * When the main unit is once fixed to wall mount, the locking pins will tighten the main unit therefore the operation test of the main unit should be required prior to fix the main unit to wall mount. If the main unit has to be disassembled from the wall mount, then you need another wall mount to be replaced as the locking pins of wall mount will be broken when the main unit detached from the wall mount. -5- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 8. Wire Color Table of the Main Unit POWER Power(DC 12V) Power(DC 12V) +12V 0V(GND) Red wire, Red with White stripe Black wire, Black with White stripe OUTPUT Door RELAY(2A) Door RELAY(2A) Door RELAY(2A) COM NC NO Gray wire with Red stripe Blue wire with White stripe White wire with Red stripe Alarm RELAY(2A) Alarm RELAY(2A) Alarm RELAY(2A) COM NC NO White wire Purple wire with White stripe Purple wire TTL Output CHIME BELL Output TTL BELL Orange wire with White stripe Brown wire with White stripe INPUT Exit Button Door Sensor External Input #1 External Input #2 External Input #3 Extra Reader Input Extra Reader Input EXIT CONTACT IN#1 IN#2 IN#3 DATA0 DATA1 Yellow wire with Red stripe Green wire Orange wire Green wire with White stripe Brown wire Pink wire Cyan wire RS232C INTERFACE RS232-TX RS232-RX RS232-GND TXD RXD GND Grey wire Blue wire Yellow wire -6- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 9. Wire connection for basic application This connection can be changed for different applications. -7- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 9-1. Power Connection Connect (+)wire of DC 12V power to Red wire and Red/White stripe wire and connect Power GND(-)wire of DC 12V to Black wire and Black/White stripe wire. 9-2. Door Lock connection 9-2-1 Connection of POWER FAIL SAFE: Door Lock - Connect Door RELAY(COM),Grey/Red stripe wire to DC +12V. - Connect (+)wire of Door Lock to Door RELAY(NC),Blue/White stripe wire. - Connect (-)wire of Door Lock to Power GND(-) wire. 9-2-2 Connection of POWER FAIL SECURE Door Lock - Connect Door RELAY(COM),Grey/Red stripe wire to DC +12V. - Connect (+)wire of Door Lock to Door RELAY(NO),White/Red stripe wire. - Connect (-)wire of Door Lock to Power GND(-) wire. 9-3. Alarm Device connection - Connect Alarm RELAY(COM),white wire to DC +12V. - Connect (+)wire of Alarm Device to Alarm RELAY(NO),Purple wire. - Connect (-)wire of Alarm Device to Power GND(-) wire. 9-4. Exit Button connection - Connect one of the wire of Exit Button to Exit Button Input, Yellow/Red stripe wire. - Connect the other wire of Exit Button to Power GND(-) wire. (In case of using Normal Closing Contact for Exit Button then please make setting change of ACTIVE level of Exit Button in section 8-20) 9-5. Door Contact sensor connection - Connect Door Contact sensor(COM) wire to Door Contact Input, Green wire. - Connect Door Contact sensor(NO) wire to Power GND(-) wire. (In case of using Normal Closing(NC) Contact for Door Contact sensor then please make setting change of ACTIVE level of Door Contact in section 8-21) 9-6. Auxiliary Input Device connection(Applied to AUX Input#1,#2,#3) - Connect one wire of Auxiliary Input Device to AUX Input wire (Input#1 Orange, Input#2 Green/White stripe, Input#3 Brown wire). - Connect the other wire of Auxiliary Input Device to Power GND(-) wire. (In case of using Normal Closing(NC) Contact for Auxiliary Input Device then please make setting change of ACTIVE level of AUX Input in section 8-17 ~ 8-19) -8- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 9-7. Auto-dialer connection(Extra Purchase, If Necessary) - Connect the input wire of Auto-dialer to TTL output, Orange/White stripe wire. - Connect (+)wire of Auto-dialer to DC +12V. - Connect (-)wire of Auto-dialer to Power GND(-) wire. - Connect Telephone Line plug(RJ-14) to Auto-dialer. (In case of using Low ACTIVE for Auto-dialer then please make setting change of ACTIVE level of TTL Output in section 8-22) 9-8. RS232C Communication port Connection 9-pin connector(COM Port, female) is required to connect Serial communication (RS232C) between Main Unit to Personal Computer. Purchase 9-pin Female Connector, then connect wires as follow. - Connect RS232-TX, Grey wire of Main Unit to pin number 2 of 9-pin connector. - Connect RS232-RX, Blue wire of Main Unit to pin number 3 of 9-pin connector. - Connect RS232-GND, Yellow wire of Main Unit to pin number 5 of 9-pin connector. - Plug in 9-pin connector to COM1 or COM2 Port of Personal Computer. - Install and run SDC1000 Time & Attendance Software. 9-9. Chime Bell Unit connection(Extra Purchase, If Necessary) - Connect Red(+) wire of Chime Bell Unit to Bell Output, Brown/White wire of Main Unit. - Connect Black(-) wire of Chime Bell Unit to Power GND(-) wire. 9-10. Extra Proximity Reader connection(Extra Purchase, If Necessary) - Connect (+)wire of Reader to DC +12V. - Connect (-)wire of Reader to Power GND(-) wire. - Connect Wiegand output DATA0 of Reader to Pink wire - Connect Wiegand output DATA1 of Reader to Cyan wire. -9- MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 10. Initial Setup Main Unit has Flash Memory to retain all setting values and when it delivered to customer there is no data in the memory therefore Initial Setup is required for the first use. 10-1. Registration of RF Cards for RF CARD ONLY MODE * This mode is only applicable when the extra proximity reader is connected. ¨ çTurn switch on DC12V Power Supply. All 3 LEDs will be flashing with starting sound. ¨ èPress 0 1 ENT from the keypad.(RF CARD ONLY MODE ) ¨ éPresent RF Cards as follow to register Master Card and User Access Cards. ........ Master Card User Access Cards Master Card(Finish setup) ¨ êFirst read card is registered as Master Card and the RF Cards followed to Master Card are registered as User Access Cards then present Master Card again to finish setup. (Please keep Master Card at the secure location for further setting changes.) ¨ ëNow, the Main Unit is entered to normal operation mode with default setting. 10-2. Registration of RF Cards with PIN for RF CARD + PIN MODE * This mode is only applicable when the extra proximity reader is connected. ¨ çTurn switch on DC12V Power Supply. All 3 LEDs will be flashing with starting sound. ¨ èPress 0 2 ENT from the keypad.(RF CARD + PIN MODE ) ¨ éPresent RF Cards as follow to register Master Card and User Access Cards and type 4~6 digits Personal Identification Number(PIN) followed by each User Access Card. ........ Master Card User Access Cards+PINENT Master Card(Finish setup) ¨ êFirst read card is registered as Master Card and the RF Cards+PINENT followed to Master Card are registered as User Access Cards with PIN numbers then present Master Card again to finish setup. (Please keep Master Card at the secure location for further setting changes.) - 10 - MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER ¨ ëNow, the Main Unit is entered to normal operation mode with default setting. 10-3. Registration of PIN ONLY MODE ¨ çTurn switch on DC12V Power Supply. All 3 LEDs will be flashing with starting sound. ¨ èPress 0 3 ENT from the keypad.(PIN ONLY MODE ) ¨ éEnter a 8 digits PIN number + ENT to register Master PIN number then type 4~6 digits PIN number + ENT to register User Access PIN numbers then type 8 digits Master PIN number to finish setup. 8digits PINENT Master PIN 4~6digits PINENT ... User Access PIN ... 8digits Master PINENT Master PIN(Finish setup) ¨ êFirst 8 digits PIN number is registered as Master PIN and 4~6 digits PIN followed to Master PIN are registered as User Access PIN numbers then type Master PIN again to finish setup. (Please write and remember Master PIN number for further setting changes.) ¨ ëNow, the Main Unit is entered to normal operation mode with default setting. 10-4. Default Setting Values After the Initial Setup, the Main Unit stores its default setting values as follows and run normal operation mode. If you want to change the setting values, add or delete USER Access Cards(or PIN) then please refer to "Setting Changes" in section 8. ¨ çWhen User Access Card(or PIN) is granted - Door RELAY activates for 3sec. - Green LED lights on for 3sec. ¨ èWhen User Access Card(or PIN) is denied - Alarm RELAY activates for 2sec. - Red LED lights on for 2sec. - 11 - MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 11. Operation 11-1. Normal Operation Mode(Safe Mode) When the Main Unit is running in normal operation mode, Yellow LED is flashing every second. 11-2. Open the Door User Access Card(or PIN) is granted, Door opens for 3 seconds with "do-mi-sol-do" melody. Registered card(or PIN) 11-3. Exit(Open the Door) To exit, press Exit Button and Door opens for 3 seconds. 11-4. Alarm by Unregistered Card(or PIN) User Access Card(or PIN) is not registered and access is denied, then Alarm RELAY activates for 2 sec. with "sol-do-sol-do" melody. Unregistered card(or PIN) (If you do not want to activate Alarm, then please change settings in section 8-22.) 11-5. Secure Mode Last exit person can change the mode from Safe Mode to Secure Mode by pressing. Secure Code from the keypad so that the Alarm will generate by AUX Inputs. -> Change to Secure Mode. It will canceled automatically when the registered card(or PIN) is present. 11-6. DURESS Alarm In case of opening the door by Duress condition, press Duress PassWordENT and open the door as usual then Duress Alarm(TTL Output) will activate. - 12 - MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 11-7. Chime Bell operation When the guest presses ESC(Bell) Button from the keypad, Chime Bell melody is activating for 5 seconds. 12. Setting Changes To change previous setting values, you need Master Card(or PIN) to get in to Setting Change mode. First present Master Card(or press Master PIN) and enter 2-digit command code. Present Master Card(or PIN) and press 2digit command code. + Command code + Command Change setting values 11 Add User Access Cards(RF CARD ONLY MODE) 12 Add User Access Cards and PIN(RF CARD + PIN MODE) 13 Add User Access PIN numbers(PIN ONLY MODE) 14 Delete User Access Cards(or PIN) 21 Change Door open time when User Access Card(or PIN) is granted 22 Change Alarm time when User Access Card(or PIN) is denied 23 Change Alarm time when Try Our error detected 24 Change Alarm time when Door Contact error detected 25 Change Alarm time when AUX#1 Input detected 26 Change Alarm time when AUX#2 Input detected 27 Change Alarm time when AUX#3 Input detected 28 Change Alarm time when magnet detected 29 Register 2 digits Duress Alarm Code 30 Change Alarm time when Duress Alarm detected 31 Test Door open time set by command "21" 32 Test Alarm time set by command "22" 33 Test Alarm time set by command "23" 34 Test Alarm time set by command "24" 35 Test Alarm time set by command "25" 36 Test Alarm time set by command "26" 37 Test Alarm time set by command "27" 39 Change Chime Bell activating time - 13 - MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER Command Change setting values 41 Unconditional Door Open 42 Unconditional Door Close 43 Enable QUICK ACCESS MODE(Operate only PIN MODE) 44 Disable QUICK ACCESS MODE(Operate only PIN MODE) 51 Disable Melody sound 52 Enable Melody sound 60 Change keypad lock time when Try Out error detected 61 Detect AUX#1 Input from 'L' to ‘H' 62 Detect AUX#1 Input from 'H' to ‘L' 63 Detect AUX#2 Input from 'L' to ‘H' 64 Detect AUX#2 Input from 'H' to ‘L' 65 Detect AUX#3 Input from 'L' to ‘H' 66 Detect AUX#3 Input from 'H' to ‘L' 67 Detect Exit Button Input from 'L' to 'H' 68 Detect Exit Button Input from 'H' to 'L' 69 Detect Door Contact sensor Input from 'L' to 'H' 70 Detect Door Contact sensor Input from 'H' to 'L' 71 Activate TTL output to ‘H' 72 Activate TTL output to ‘L' 77 Enable Chime Bell Output 78 Disable Chime Bell Output 80 Set delay time to activate SECURE MODE 81 Set watch-dog time for Door Contact sensor 82 Set number of times of Try-Out 83 Set input limit time from the keypad 84 Set Temper Alarm port 88 Enable Temper Alarm 89 Disable temper Alarm 99 Initialize and erase all setup data - 14 - MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-11. Add User Access Cards(RF CARD ONLY MODE) 11ENT Master card Command ..... Cards to be registered .... Master card 12-12. Add User Access Cards(RF CARD + PIN MODE) 12ENT Master card Command PINENT ..... Cards to be registered .... Master card 12-13. Add User Access PIN(PIN ONLY MODE) MasterPINENT 13ENT Master PIN Command PINENT ..... MasterPINENT PIN to be registered .... Master PIN 12-14.1. Delete User Access Cards(RF CARD ONLY MODE, RF CARD+PIN MODE) Master Card 14ENT CardNumberENT Command Cards to be deleted .... ..... Master Card 12-14.2. Delete User Access PIN(PIN ONLY MODE) MasterPINENT 14ENT PINENT ..... Master PIN Command PIN to be deleted .... - 15 - MasterPINENT Master PIN MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 24 Creator : Microsoft Word Create Date : 2001³â 2¿ù 12ÀÏ Monday 10:34:41 ¿ÀÀü Title : SDC1000_MANUAL.PDF Author : Unknown Producer : Acrobat PDFWriter 3.0 for Windows Subject :EXIF Metadata provided by EXIF.tools