Hangzhou Hikvision Digital Technology DSKIR Card Reader User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2637175
Application ID	OrjzhhAAqbX3UzCxnOGJTg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.36kB (541963 bits)
Date Submitted	2015-06-05 00:00:00
Date Available	2015-06-08 00:00:00
Creation Date	2015-04-20 15:28:26
Producing Software	GPL Ghostscript 8.64
Document Lastmod	2015-04-20 07:28:28
Document Title	(Microsoft Word - UD.6L0206A1004A01_Baseline_Imstall \323\303\273\247\312\326\262\341.doc)
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Amy-D_Wang

DS-K1100 Series Card Reader
Installation Manual
UD.6L0206A1004A01
Regulatory information
FCC information
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This product has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.
Thank you for purchasing our product. If there is any question or
request, please do not hesitate to contact the dealer.
This manual is applicable to the following models:
Series
Models
Description
DS-K1101M
MIFARE card reader (without keypad)
DS-K1101 DS-K1101MK MIFARE card reader (with a keypad)
Series
DS-K1101C
CPU card reader (without keypad)
DS-K1101CK
CPU card reader (with a keypad)
DS-K1102M
MIFARE card reader (without keypad)
DS-K1102 DS-K1102MK MIFARE card reader (with a keypad)
Series
DS-K1102C
CPU card reader (without keypad)
DS-K1102CK
CPU card reader (with a keypad)
DS-K1103M
MIFARE card reader (without keypad)
DS-K1103 DS-K1103MK MIFARE card reader (with a keypad)
Series
DS-K1103C
CPU card reader (without keypad)
DS-K1103CK
CPU card reader (with a keypad)
DS-K1104M
MIFARE card reader (without keypad)
DS-K1104 DS-K1104MK MIFARE card reader (with a keypad)
Series
DS-K1104C
CPU card reader (without keypad)
DS-K1104CK
CPU card reader (with a keypad)
This manual is a kind of guide only for reference and may contain
several technically inaccurate points or printing errors, and the
content is subject to change without notice. The updates will be
added into the new version of this manual. We will readily
improve or update the products or procedures described in the
manual.
There may be differences between real object. The real product
should be considered as final.
Chapter 1 Preventive and Cautionary
Tips
To guarantee the card reader works properly, please read and
obey the notes below.

 If the card reader is powered by the controller, the power
supply distance is recommended to be no longer than 100m.
If the distance is longer than 100m, you are advised to power
the card reader by external 12V (range: -%10 ~ +%10) DC
power supply, which is nonswitched and linear.

 To guarantee the communication between the controller and
the card reader, you must use RVVP cable above 0.5 to
connect them.

 If the card reader is installed outside or in environment easy
to permeable, it is advisable to install a waterproof shield.

 If you need to install several card readers, the distance
among them must over 30cm.

 To reduce the noise in long distance transmission, the shield
of cable should connect to the GND of both controller and
card reader terminal.
Chapter 2 Introduction
DS-K1100 series card reader is a kind of high-performance
product, with a 32 bit high-speed processor. It communicates with
access controller via either RS-485 protocol or Wiegand protocol.
And a build-in tamper-proof module helps to protect card reader
from malicious damage. As to the physical appearance, the
PC+ABS material makes water proof and dust proof possible in
poor environment.
2.1 Front View
The front view of DS-K1101 series card reader is shown below:
Figure 2-1 DS-K1101MK/DS-K1101CK
Figure 2-2 DS-K1101M/DS-K1101C
The front view of DS-K1102 series card reader is shown below:
Figure 2-3 DS-K1102MK/DS-K1102CK
Figure 2-4 DS-K1102M/DS-K1102C
The front view of DS-K1103 series card reader is shown below:
Figure 2-5 DS-K1103MK/DS-K1103CK Figure 2-6 DS-K1103M/DS-K1103C
The front view of DS-K1104 series card reader is shown below:
Figure 2-7 DS-K1104MK/DS-K1104CK
Figure 2-8 DS-K1104M/DS-K1104C
2.2 Rear View
The rear view of card reader is shown below:
2
Figure 2-9 Rear View of DS-K1101 Series
Figure 2-10 Rear View of DS-K1102 Series
1
Figure 2-11 Rear View of DS-K1103 Series
Figure 2-12 Rear View of DS-K1104 Series
Table 2-1 Description of Rear View
No.
Name
Cable Interface of RS-485, Power, LED Control, etc.
Buzzer
Tamper-proof Module
DIP Switch
PSAM Card Slot (available for CPU card reader)
2.3 Side View
The side view of card reader is shown below:
Figure 2-13 DS-K1101 Series
Figure 2-14 DS-K1102 Series
Figure 2-15 DS-K1103 Series
Figure 2-16 DS-K1104 Series
Chapter 3 Installation
3.1 Installing PSAM Card
PSAM card slot is only available for CPU card reader.
Insert the PSAM card into the slot according to the direction
shown below.
Figure 3-1 PSAM Card Slot
3.2 Introduction for DIP Switch
The DIP switch module is shown below. The No. of DIP switch
from left to right is 1 ~ 8.
Figure 3-2 DIP Switch Module
Table 3-1 Description of DIP Switch
Icon
Description
Represent 1 in binary mode
Represent 0 in binary mode
For example, binary value of the following status is: 0000 1100.
Figure 3-3 DIP Switch Module
Table 3-2 Description of DIP Switch
No.
1~4
Description
Address of RS-485
Read card No. or file in card.
(Only available for CPU card
reader.)
Wiegand protocol or RS-485
protocol.
10
DIP Switch Status
1: 1
0: 0
1: read card No;
0: read file in card.
1: Wiegand protocol;
0: RS-485 protocol.
No.
Description
Wiegand Protocol
(available when No. 6 is 1)
Matched Resistance
(available for RS-485 protocol)
DIP Switch Status
1: Wiegand protocol
of 26-bit;
0: Wiegand protocol
of 34-bit.
1: Enable;
0: Disable.
3.3 Definition of Cable
The description of 10 cables is shown below.
Table 3-3 Description of Cable
Color
Yellow
Brown
Blue
Purple
Gray
Green
White
Black
Orange
Red
Description
RS-485+
Blue LED Control (available for Wiegand Protocol)
RS-485Beep Control (available for Wiegand Protocol)
Case Sensor (available for Wiegand Protocol)
Wiegand W0 (available for Wiegand Protocol)
Wiegand W1 (available for Wiegand Protocol)
GND
Red LED Control (available for Wiegand Protocol)
PWR (DC +12V)
3.4 Wiring Cables
Purpose:
Wire the cables between controller and card reader, thus to
establish the communication between them.
Steps for RS-485 communication mode:
11
1.
2.
3.
Set the DIP switch of No. 6 as 0.
Set the DIP switch of No. 1 ~ 5 for RS-485 address and
reading card mode. For details, please refer to 3.2
Introduction for DIP Switch.
Wire the cable between controller and card reader as
shown below.
Figure 3-4 Wiring for RS-485 Communication Mode
Steps for Wiegand communication mode:
1. Set the DIP switch of No. 6 as 1.
2. Set the DIP switch of No. 5 and 7 for reading card mode and
Wiegand protocol. For details, please refer to 3.2
Introduction for DIP Switch.
12
3.
Wiring the cable between controller and card reader as
shown below.
Figure 3-5 Wiring for Wiegand Communication Mode
3.5 Installing Card Reader
Before you start:
Set the DIP switch. For details, refer to 3.2 Introduction for DIP
Switch.
Steps:
13
1.
2.
3.
4.
Fix the plate on the wall or other
place.
Connect the cables between
controller and card reader. For
details, refer to 3.4 Wiring
Cables.
Push the card reader to match
the fixed plate.
Fasten the screw to keep the
components together.
Chapter 4 Sound Prompt and Indicator
After the card reader is powered on, LED status indicator will turn
blue and blink for 1 time. Then it will turn red and blink for 3
times. At last the buzzer will send out a beep sound indicating the
starting up process is completed.
During using the card reader, it will send out different sounds
prompt and the LED indicator on it have different statuses. You
can refer to tables below for detailed information.
14
Table 4-1 Description of Prompt Sound
Sound Prompt
Description
RS-485 protocol: Pressing keys prompt;
Swiping card prompt; Time out prompt for
One beep
pressing keys or swiping card.
Wiegand protocol: Pressing keys prompt;
Swiping card prompt.
The operation of pressing keys or swiping
Two rapid beeps
card is valid.
The operation of pressing keys or swiping
Three slow beeps
card is invalid.
Rapidly
Alarm of tamper-proof.
continuous beeps
Slowly continuous
The card reader is unencrypted.
beeps
Table 4-2 Description of LED Indicator
LED Indicator Status
Description
Blue and blinking
Card reader is working normally.
The operation of pressing keys or swiping
Solid blue
card is valid.
The operation of pressing keys or swiping
Solid red
card is invalid.
For RS-485 protocol: Registering failed or
Red and blinking
card reader is offline.
Red and Keeping Available for reading file mode of CPU
rapidly blinking
card: PSAM is not inserted or undetected.
Red and keeping
Failed to get key files of PSAM card; Failed
rapidly blinking and
to detect the PSAM card.
slowly beeps
15
16

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 17
Create Date                     : 2015:04:20 15:28:26+08:00
Title                           : (Microsoft Word - UD.6L0206A1004A01_Baseline_Imstall \323\303\273\247\312\326\262\341.doc)
Producer                        : GPL Ghostscript 8.64
Author                          : Amy-D_Wang
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2015:04:20 07:28:28Z

EXIF Metadata provided by EXIF.tools