Hangzhou Hikvision Digital Technology I002U40 Network Camera User Manual

Hangzhou Hikvision Digital Technology Co., Ltd. Network Camera Users Manual

Users Manual

134 5 6Appearance*使用产品前请仔细阅读快速操作指南，并妥善保管UDName DescriponIR LightLEDIndicatorAuto light source for night vision. The light is behind the an-reflecon panel. You can see the light when it is on.RESET/WPS WPS: Set Wi-Fi connecon via WPS (Wi-Fi Protected Setup) funcon.RESET: Hold down the buon for 10 seconds when the camera is starng up or reboong.MemoryCard SlotFor microSD card. If a memory card is used, video files will be stored in the memory card. You would need to inialize it via the Hik-Connect app/web browser/client soware.Steady red: The camera is starng up.Flashing blue: The camera is on and ready for the Wi-Fi connecon.Steady blue: The camera is running properly.Flashing red: Network excepon.. . . Network Cube CameraQuick Start Guide2Regulatory InformaonFCC InformaonPlease take aenon that changes or modificaon not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separaon between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.FCC CondionsThis device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operaon.EU Conformity Statement. This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU, Radio Equipment Direcve 2014/53/EU.2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info. 2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for specific baery informaon. The baery is marked with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to your supplier or to a designated collecon point. For more informaon see: www.recyclethis.info.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitaon est autorisée aux deux condions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconnement.Under Industry Canada regulaons, this radio transmier may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmier by Industry Canada. To reduce potenal radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communicaon.Conformément à la réglementaon d'Industrie Canada, le présent émeeur radio peut fonconner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émeeur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intenon des autres ulisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communicaon sasfaisante.This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.Cet équipement doit être installé et ulisé à une distance minimale de 20 cm entre le radiateur et votre corps.Industry Canada ICES-003 ComplianceThis device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is subject to the following two condions: (1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operaon of the device.Safety InstruconThese instrucons are intended to ensure that a user can use the product correctly to avoid danger or property loss. The precauon measure is divided into “Warnings” and “Cauons”Warnings: Serious injury or death may occur if any of the warnings are neglected.Cauons: Injury or equipment damage may occur if any of the cauons are neglected.Warnings: Follow these safeguards to prevent serious injury or death.Cauons: Follow these precauons to prevent potenal injury or material damage. Warnings● Proper configuraon of all passwords and other security sengs is the responsibility of the installer and/or end-user.● In the use of the product, you must be in strict compliance with the electrical safety regulaons of the naon and region. Please refer to technical specificaons for detailed informaon.● Do not connect several devices to one power adapter as adapter overload may cause over-heang or a fire hazard.● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor, or noise rise from the device, turn off the power at once and unplug the power cable, and contact the service center. ● Make sure the power supply voltage is correct before using the camera.● Do not drop the camera or subject it to physical shock.● Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. ● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur (which is not a malfuncon), and affect the sensor’s endurance at the same me.● The sensor may be burned out by a laser beam, so when any laser equipment is in use, make sure that the surface of sensor will not be exposed to the laser beam.● Do not place the camera in extremely hot, cold (the operang temperature shall be -10°C to +50°C), dusty, or damp locaons, and do not expose it to high electromagnec radiaon. ● To avoid heat accumulaon, ensure that there is good venlaon to the device. ● Keep the camera away from liquids. ● While in delivery, pack the camera in its original, or equivalent, packing, packing materials. Or packing of the same texture.● Regular part replacement: a few parts (e.g. electrolyc capacitor) of the equipment shall be replaced regularly according to their average endurance. The average me varies because of differences between operang environments and usage history, so regular checking is recommended for all users. Please contact your dealer for more details.● Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used baeries according to the instrucons provided by the baery manufacturer. ● If the product does not work properly, please contact your dealer or the nearest service center. Never aempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)CauonsName DescriponFor the power supply, (12V ). Plug the power cable into the power input interface to power on the camera.Power InputRESET/WPS2Install the camera.Paste the mounng template onto the installaon surface.1Quick Start GuideCOPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED.Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons, express or implied, regarding to the Manual.About this ManualThe Manual includes instrucons for using and managing the product. Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the Manual is subject to change, without noce, due to firmware updates or other reasons. Please find the latest version in the company website (hp://overseas.hikvision.com/en/). Visit the company website (hp://overseas.hikvision.com/en/) to get the manuals, client soware, and developing tools.Please use this user manual under the guidance of professionals.Trademarks Acknowledgment and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and logos menoned below are the properes of their respecve owners.Legal DisclaimerTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.IR LightStatusIndicatorLensMICBracketSpeakerPower InterfaceMemory Card Slot1Install memory card (oponal).Unscrew the cover to expose the memory card slot.Installaon1Insert the memory card. (Oponal) to unmount the memory card, push to get it ejected. 2Screw the cover back.3111Align the screw holes on mounng surface with those on the bracket. Fix the bracket with three screws.4Drill three screw holes according to the template.2Pry the bracket open at the “OPEN” sign. Remove the trim ring.3Trim Ring676813
14910 11 133Install the trim ring back.Loosen the adjusng screw on bracket.Seng the Network Camera over the LANStep 1WiringConnect the camera to the network according to the following figures. You can connect the camera directly to a computer, or connect i t via a router or switch.- Check the memory card status by tapping on the Storage Status in the Device Sengs interface.- If the memory card status displays as Uninialized, tap to inialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as moon detecon.RecordingLaunch the Hik-Connect app, tap a connected device and tap Gallery buon to play back.PlaybackLaunch the Hik-Connect app and tap Message to see the alarm messages.Alarm Noficaon51Hold the camera body to adjust the panning and lng posion.2Adjust the surveillance angle.Hik-Connect Setup- Download and install the Hik-Connect app by searching the “Hik-Connect” in App Store or Google PlayTM.- Launch the app and register for a Hik-Connect user account.- Log in Hik-Connect app aer registraon.15Modifying the IP AddressStep 3To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. You can use SADP to change the IP address of the camera. Note: you can also use client soware to modify IP address. Refer to the user manual of client soware for detailed informaon.- Run the SADP soware.- Select the device. If the device is inacve, acvate it first.- Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.- Input the password to take effect the IP address modificaon.360°120504151061208NutScrew the camera body to the bracket. Tighten the nut.690°30°Adjusng ScrewTighten the adjusng screw aer adjustment.3 半球Network CableorNetwork Camera Computer 网络交换机半球Network CableNetwork CableororNetwork Camera Computer Step 2Acvate the Camera via Web Browser- Input the IP address into the address bar of the web browser, and click Enter to enter the acvaon interface.Note:The default IP address of the camera is 192.168.1.64.For the camera enables the DHCP by default, you need to acvate the camera via SADP soware and search the IP addrss.- Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case leers, lower case leers, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, reseng the password monthly or weekly can beer protect your product.- Confirm the password.- Click OK to save the password and enter the live view interface.Acvate the Camera via SADP- Get the SADP soware from the supplied disk or the official website, and install the SADP according to the prompts.- Run the SADP soware to search the online devices.- Check the device status from the device list, and select the inacve device.- Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case leers, lower case leers, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, reseng the password monthly or weekly can beer protect your product.- Click OK to save the password.Accessing via Web BrowserSystem RequirementOperang System: Microso Windows XP SP1 and above version CPU: 2.0 GHz or higherRAM: 1G or higherDisplay: 1024×768 resoluon or higherWeb Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version- Open the web browser.- In the browser address bar, input the IP address of the network camera (the modified IP address), and press the Enter key to enter the login interface.- Input the user name and password. Click Login. Note: The device IP address gets locked if the admin user performs 7 failed password aempts (5 aempts for the user/operator).- Install the plug-in. Note: You may have to close the web browser to finish the installaon of the plug-in.- Reopen the web browser aer the installaon of the plug-in and repeat the steps to login.Operang via Hik-Connect AppStep 1Step 2Adding Device to Hik-Connect- Use a network cable to connect the device with a router if the device does not support Wi-Fi. Note: Aer the device connects to the network, please wait one minute before any operaon on the device using Hik-Connect app. - In the Hik-Connect app, tap “+” on the upper-right corner and then scan the QR code of the device to add the device. You can find the QR code on the mounng base of the device or on the cover of the Quick Start Guide of the device in the device package.- Follow the prompts to set the network connecon and add the device to your Hik-Connect account.Step 3Launch the Hik-Connect app and you can get the live view of the connected devices.Live View16

Navigation menu