Hansol LCD B15AC 15" CCTV MONITOR User Manual USERS MANUAL

Hansol LCD Inc. 15" CCTV MONITOR USERS MANUAL

USERS MANUAL

Parts 3Connection to Signal Source 4the range of control Angle 5Installing Monitor Driver 6Name and Function of Front 8Power Management Feature 9Adjusting OSD 11Standard Signal Table 22Specification 24Troubleshooting 25Warning 27Table of ContentsINFORMATION TO USER :This equipment has been tested and found to comply with the limits of a ClassB digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and canradiate radio frequency energy and,if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation; if this equipment does cause harmful interference to radio ortelevision reception, which can be determined by determined by turning theequipment off and on, the user is encouraged to try to crrent the interference byone or more of the fllowing measures:1. Reorient/Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit differencefrom that to which the recerver is connected.4. Consult the dealer or an experienced radio/TV technician for help.CAUTIONChanges or modifications not expressly approved by themanufacturer responsible for compliance could void the user's authority to operate the equipmentENERGY STARAs an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency.
English - 32 - EnglishPartsPlace the monitor to face the user and then adjust the monitor angle.Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cmLook down the monitorbelow the horizon.Relax shoulders and arms, and sit back on the chair.Adjust the monitor to prevent reflection.Adjust the monitor stand to acquire required angle.Keep feet flat on the ground.Maintain the arms horizontallyand place hands softly on the keyboard.Good Posture GuideUser's Manual /Warranty CardSignal Cable AC Power CableLCD Monitor
English - 54 - EnglishConnection to Signal Source 1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and Signal Source via Signal cable3. Power on the monitor and computer.4. Connection is finished.General For MacintoshAdapter for Macintosh (Optional)Refer to the table on the rear side ofthe optional Macintosh adapter andadjust DIP switch by the resolution. T he range of control Angle< Power source connection > < Signal cable connection> Basic ConnectionPort for AC power cable.Port for BNC inputPort for S-VHS inputPort for signal cable from signal source.Kensington LockHow to Adjust the StandForward 4DefaultBackward 31
+/ -/English - 76 - EnglishPower buttonPower button is located in the lower center of the Front Bezel.You can push the button to turn on/off the power.Power Indicating LEDDark : Power off Green : Normal modeGreen blinking : DPMS mode or Check Signal Cable mode.On-Screen Display (OSD) Function ButtonOSD buttons on the front of bezel perform the following functions.SOURCE: Monitor displays source of the signal in order ( PC CVBS S-VHS )MENU/EXIT : Press this button to display menus. If you press this button when OSD is displayed, you can switch display to the previous menu and exit menu.SELECT : When OSD is displayed, You can select icons.POWER : Power button.: By pressing these buttons when OSD is displayed, you can move cursor into the menus which you want.After pressing the SELECT button, you can change gauge level or select submenus.When OSD is not displayed, you can adjust brightness or contrast.AUTO : Press this button, when OSD is not displayed, to performautomatic setting. (only PC Mode.)Name and Function of Front Front panel FunctionsAUTOBUTTON/ +BUTTONPOWER BUTTON(Power indicating LED)/ - BUTTONSELECTBUTTONMENU/EXIT BUTTONSOURCE BUTTON
English - 98 - EnglishNo image is displayed with Green blinking.Monitor is in power saving mode.Use mouse or keyboard to release power saving mode.No image is displayed without LED on.Power cable plug must be pulled out.Check the power plug on monitor and on the wall."Out of range" displayed on the screen.This message is displayed when the signal from video card exceeds themaximum frequency of the monitor. Readjust resolution and frequency inaccordance with the monitor capacity. (Refer to Standard Signal Table)Power Management FeatureThe monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling(DPMS) mode of Video Electronics Standard Association (VESA).The power management feature requires that the video card of thecomputer should support DPMS function. Adjusting OSD -PC MODEBrightnessContrast1. Use to move Brightness ICON.2. Press SELECT button to select it.3. Use to adjust the brightness of the screen. SELECTBrightness / ContrastMENU1. Press the MENU button to access main menu.2. Use to move Brightness / Contrast ICON.3. Press SELECT button into the submenu.SELECTSELECT1. Use to move Contrast ICON.2. Press SELECT button to select it.3. Use to adjust the contrast of the screen. Status LED Sign Power ConsumptionNormal mode Green ON Normal PowerDPMS mode Green Blinking 3W or Below
English - 1110 - EnglishHorizontal PositionSELECT1. Use to move H-Position ICON.2. Press SELECT button to select it.3. Use to adjust display left or right.Clock PhaseMENU SELECT1. Press the MENU button to access main menu.2. Use to move CLOCK PHASE ICON.3. Press SELECT button into the submenu.According to the characteristic of video card,control range can be changed.1. Use to move V-Position ICON.2. Press SELECT button to select it.3. Use to adjust display upward or downward.1. Press to move Phase ICON.2. Use SELECT button to select it.3. Use to correct fine trembling or Video noise.1. Use to move Clock ICON.2. Press SELECT button to select it.3. Press orto remove vertical noise.( Adjusting clock phase is required after the adjustment of clock.) SELECTSELECTSELECTVertical PositionClockPhaseAccording to the characteristic of video card,control range can be changed.1. Press MENU button to access main menu.2. Use to move Color ICON.3. Press SELECT button into the submenu.MENU SELECTColor
English - 1312 - EnglishUser Color1. Use to move User color ICON.2. Press SELECT button to select it.3. Use to increase or decrease each color.1. Use to select the Mode 1, and Mode 2.2. Press the Menu button to return previous state.9300K : Slightly Bluish white.6500K : Slightly Reddish white.MENUMENUSELECTPreset Color1. Use to move OSD V-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD upward or downward.1. Use to move OSD Time ICON.2. Press SELECT button to select it.3. Use to adjust OSD display time.4. Press Menu button to return main menu.SELECTOSD TimeOSD V-Position1. Use to move OSD H-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD left or right.SELECTOSD H-PositionSELECT1. Press MENU button to access main menu.2. Use to move OSD ICON.3. Press SELECT button into the submenu.MENU SELECTOSD
English - 151. Use to move Language ICON.2. Press SELECT button to select it.3. Use to select language.MENU SELECTLanguage14 - English1. Use to move the Information ICON.2. Press SELECT button to select it.MENUInformation1. Use to move the Factory Reset ICON.2. Press SELECT button to return to default setting.Factory ResetSELECTSELECTYou can know display information1. Press the MENU button to access main menu.2. Use to move Special ICON.3. Press SELECT button into the submenu.MENU SELECTSpecialAccording to the characteristic of video card, display information can be incorrect
English - 1716 - EnglishAdjusting OSD-CVBS, S-VIDEO MODEBrightnessContrast1. Use to move Brightness ICON.2. Press SELECT button to select it.3. Use to adjust the brightness of the screen. SELECTBrightness / ContrastMENU1. Press the MENU button to access main menu.2. Use to move Brightness / Contrast ICON.3. Press SELECT button into the submenu.SELECTSELECT1. Use to move Contrast ICON.2. Press SELECT button to select it.3. Use to adjust the contrast of the screen. Sharpness(CVBS,S-VIDEO Mode)1. Press the MENU button to access main menu.2. Use to move Sharpness ICON.3. Press SELECT button to select it.4. Use to adjust the sharpness.(Adjust the clearness of the screen)HUE(CVBS,S-VIDEO Mode)1. Use to select the HUE ICON.2. Press SELECT button to select it.3. Use to adjust the HUE.SELECT1. Press MENU button to access main menu.2. Use to move Color ICON.3. Press SELECT button into the submenu.MENU SELECTColorSELECT
English - 191. Use to move OSD V-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD upward or downward.SELECTOSD V-Position1. Use to move OSD H-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD left or right.SELECTOSD H-Position1. Press MENU button to access main menu.2. Use to move OSD ICON.3. Press SELECT button into the submenu.MENU SELECTOSD18 - English1. Use to select the Saturation ICON.2. Press SELECT button to select it.3. Use to adjust the saturation.SELECTSaturation(CVBS,S-VIDEO Mode)1. Use to select the Mode 1, and Mode 2.2. Press the Menu button to return to the previous state.9300K : Slightly Bluish white.6500K : Slightly Reddish white.MENUPreset ColorUser Color1. Use to move User color ICON.2. Press SELECT button to select it.3. Use to increase or decrease each color.MENUSELECT
English - 2120 - English1. Use to move the Information ICON.2. Press SELECT button to select it.MENUInformationSELECTYou can know display informationAccording to the characteristic of video card, display information can be incorrect1. Use to move the Factory Reset ICON.2. Press SELECT button to return to default setting.Factory ResetSELECT1. Press the MENU button to access main menu.2. Use to move Special ICON.3. Press SELECT button into the submenu.MENU SELECTSpecial1. Use to move Language ICON.2. Press SELECT button to select it.3. Use to select language.MENU SELECTLanguage1. Use to move OSD Time ICON.2. Press SELECT button to select it.3. Use to adjust OSD display time.4. Press Menu button to return main menu.OSD TimeSELECT
English - 2322 - EnglishStandard Signal TableNTSC 1 (616 X 452)NTSC 2 (680 X 452)PAL 1 (736 X 544)PAL 2 (680 X 544)31.46931.46931.25031.25059.94059.94050.00050.00024.545427.00029.50027.000ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)PC Supported ModeDVR Supported ModePin assignment table D-SubMini 15pin connector1511 1561015pin D-SubPin No. Assignment Pin No. Assignment 1 Red Video 9 5V Input2 Green Video 10 Ground3 Blue Video 11 Ground4 N.C 12 SDA5 Ground 13 H.Sync6 Red Video Ground 14 V.Sync7 Green Video Ground 15 SCL 8 Blue Video GroundVGA (720 X 400)VGA (640 X 480)VGA (640 X 480)SVGA (800 X 600)SVGA (800 X 600)XGA (1024 X 768)XGA (1024 X 768)MAC (640 X 480)MAC (832 X 624)31.46931.46937.50037.90046.87548.36360.02335.00049.72670.08759.94075.00060.32075.00060.00475.02966.66774.551 28.32225.17531.50040.00049.50065.00078.75030.24057.284 ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)
English - 25TroubleshootingCheck the power connection. (Refer to page 4)Power LED is dark.No picture.Perform Auto_config.OSD, "check RGB( CVBS, SVIDEO)" is displayed on thescreen.Check the signal cable or signal Source.(Refer to page 4)Screen looks to be rundown.Screen is not clear.Check the resolution and frequency of computer and video card, and set up again refer to the current monitor mode and standard signal mode table.Display is unstable andtrembling.Remove attaches to the signal line(Video extension cable and others) and switch on.Perform Auto-config.Adjust clock and PHASE.24 - EnglishSpecificationType Amorphous active matrix super TFT LCDScreen Size 38.1cm (Diagonal)Maximum Resolution1024 X 768 @ 75 HzPixel Range0.297 mm X 0.297 mmDisplay Colors 16.2M ColorContrast Ratio 300 : 1Viewing Angle 70° / 70° / 55° / 60° (Left / Right / Up / Down)Response Time 25 msecLuminance 250 cd/mHorizontal Frequency 60kHz (Max.)Vertical Frequency 75 Hz (Max.)Maximum 40WPower Saving Mode Under 3WSOURCE, MENU/ EXIT, SELECT, POWER,, AUTOInput Video : Analog RGB(0.714Vpp)75ohm,Composite in (BNC),S-VHS inConnector 15-pin Mini D-sub, Stereo, S-VHS, BNC *1IBM VGA,SVGA,XGANormal&Ergonomic ModesVideo NTSC/PAL standardInput : 100-240Vac (50/60 Hz), 0.45AVESA StandardSafety Standard UL / C-ULEMI FCCSize and Weight352 156 369/ 4.1kgLCDPanelSynchronizationModel H550V(B15ACInputSignalCompatibilityPower ConsumptionControl keyFront Part SafetyStandard& EMIDimensionPower Supply Wall Mount, +/-/
English - 2726 - EnglishWarningTo prevent damage or loss, please read this warning carefully.When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short.To prevent electric shock, do not connect/dis-connect the plug with wet hand.To prevent fire, do not connect a large number ofequipments in a single line.To prevent fire and electric shock, pull out the plug incase of thunder and lightening.To prevent fire and electric shock, do not try to takethe monitor apart or repair it yourself. Contact yourlocal service station or customer service center forinspection, modification or repair.If you see smoke or smell something burning, stopusing the unit, switch off the power, pull out the plug,and then contact your local service station.Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.Double images or'ghosts'.Perform Auto-Config.Adjust COLOR at User Mode in OSD Color Menu.Picture is dark.Picture is biased or cutor too wide.Monitor is in DPMS mode.Power LED turns intoGreen blinking.Adjust COLOR at User Mode in OSD Color Menu.Color is irregular.

Navigation menu