Hansol LCD B15AC 15" CCTV MONITOR User Manual USERS MANUAL

Hansol LCD Inc. 15" CCTV MONITOR USERS MANUAL

USERS MANUAL

Download: Hansol LCD B15AC 15" CCTV MONITOR User Manual USERS MANUAL
Mirror Download [FCC.gov]Hansol LCD B15AC 15" CCTV MONITOR User Manual USERS MANUAL
Document ID422550
Application IDXkHRfYTLqsspKPj/tUnGmg==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize74.18kB (927200 bits)
Date Submitted2004-05-13 00:00:00
Date Available2004-05-13 00:00:00
Creation Date2004-05-12 11:20:33
Producing SoftwareAcrobat Distiller 4.0.5 for Macintosh
Document Lastmod2004-05-12 01:55:34
Document TitleUSERS MANUAL

INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and,if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by determined by turning the
equipment off and on, the user is encouraged to try to crrent the interference by
one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
Table of Contents
Parts
Connection to Signal Source
the range of control Angle
Installing Monitor Driver
Name and Function of Front
Power Management Feature
Adjusting OSD
11
Standard Signal Table
22
Specification
24
Troubleshooting
25
Warning
27
3. Connect the equipment into an outlet on a circuit difference
from that to which the recerver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment
ENERGY STAR
As an ENERGY STAR partner, Hansol Electronics Inc.
has determined that this product meets energy Star guidelines
for energy efficiency.
Good Posture Guide
Parts
Place the monitor to face the user and then adjust the monitor angle.
Take a break (for about 10 minutes) at every hour during the work with monitor.
Refer to the following figure to take the correct posture.
about 50cm
Look down the monitor
below the horizon.
Adjust the monitor to
prevent reflection.
LCD Monitor
Relax shoulders and arms,
and sit back on the chair.
Adjust the monitor stand
to acquire required angle.
Maintain the arms horizontally
and place hands softly on
the keyboard.
Signal Cable
AC Power Cable
User's Manual /
Warranty Card
Keep feet flat on the ground.
2 - English
English - 3
Connection to Signal Source
Basic Connection
The range of control Angle
How to Adjust the Stand
Port for AC power cable.
Port for BNC input
Port for S-VHS input
Port for signal cable from signal source.
Kensington Lock
Forward 4
< Power source connection >
< Signal cable connection>
General
For Macintosh
Default
Adapter for Macintosh (Optional)
Refer to the table on the rear side of
the optional Macintosh adapter and
adjust DIP switch by the resolution.
1. Use 220 V or 110 V. (Free Voltage)
2. Connect monitor and Signal Source via Signal cable
3. Power on the monitor and computer.
4. Connection is finished.
4 - English
Backward 31
English - 5
Name and Function of Front
Front panel
Functions
Power button
Power button is located in the lower center of the Front Bezel.
You can push the button to turn on/off the power.
Power Indicating LED
Dark : Power off
Green : Normal mode
Green blinking : DPMS mode or Check Signal Cable mode.
On-Screen Display (OSD) Function Button
OSD buttons on the front of bezel perform the following functions.
SOURCE BUTTON
AUTO BUTTON
/ + BUTTON
MENU/EXIT BUTTON
SELECT BUTTON
/ - BUTTON
POWER BUTTON
(Power indicating LED)
6 - English
SOURCE : Monitor displays source of the signal in order ( PC CVBS
S-VHS )
MENU/EXIT : Press this button to display menus. If you press this button when
OSD is displayed, you can switch display to the previous menu and
exit menu.
SELECT : When OSD is displayed, You can select icons.
POWER : Power button.
+/
-/
: By pressing these buttons when OSD is displayed, you can move
cursor into the menus which you want.
After pressing the SELECT button, you can change gauge level or
select submenus.
When OSD is not displayed, you can adjust brightness or contrast.
AUTO : Press this button, when OSD is not displayed, to perform
automatic setting. (only PC Mode.)
English - 7
Power Management Feature
The monitor is equipped with a power saving circuit that
confirms to the world-standard Display Power Manager Signalling
(DPMS) mode of Video Electronics Standard Association (VESA).
The power management feature requires that the video card of the
computer should support DPMS function.
Status
LED Sign
Power Consumption
Normal mode
Green ON
Normal Power
DPMS mode
Green Blinking
3W or Below
Adjusting OSD
-P C M O D E
Brightness / Contrast
MENU
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Brightness / Contrast ICON.
3. Press SELECT button into the submenu.
Brightness
SELECT
1. Use
to move Brightness ICON.
2. Press SELECT button to select it.
3. Use
to adjust the brightness of the screen.
No image is displayed with Green blinking.
Monitor is in power saving mode.
Use mouse or keyboard to release power saving mode.
No image is displayed without LED on.
Power cable plug must be pulled out.
Check the power plug on monitor and on the wall.
"Out of range" displayed on the screen.
This message is displayed when the signal from video card exceeds the
maximum frequency of the monitor. Readjust resolution and frequency in
accordance with the monitor capacity. (Refer to Standard Signal Table)
8 - English
Contrast
SELECT
1. Use
to move Contrast ICON.
2. Press SELECT button to select it.
3. Use
to adjust the contrast of the screen.
English - 9
Phase
Clock Phase
SELECT
MENU
1. Press the MENU button to access main menu.
2. Use
to move CLOCK PHASE ICON.
3. Press SELECT button into the submenu.
SELECT
1. Press
to move Phase ICON.
2. Use SELECT button to select it.
to correct fine trembling or Video noise.
3. Use
Clock
Horizontal Position
SELECT
SELECT
1. Use
to move H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust display left or right.
1. Use
to move Clock ICON.
2. Press SELECT button to select it.
3. Press or
to remove vertical noise.
( Adjusting clock phase is required after the
adjustment of clock.)
According to the characteristic of video card,
control range can be changed.
Color
Vertical Position
SELECT
1. Use
to move V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust display upward or downward.
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move Color ICON.
3. Press SELECT button into the submenu.
According to the characteristic of video card,
control range can be changed.
10 - English
English - 11
OSD H-Position
Preset Color
MENU
SELECT
1. Use
to select the Mode 1, and Mode 2.
2. Press the Menu button to return previous state.
9300K : Slightly Bluish white.
6500K : Slightly Reddish white.
OSD V-Position
User Color
SELECT
SELECT
MENU
1. Use
to move User color ICON.
2. Press SELECT button to select it.
3. Use
to increase or decrease each color.
OSD
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move OSD ICON.
3. Press SELECT button into the submenu.
12 - English
1. Use
to move OSD H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD left or right.
1. Use
to move OSD V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD upward or downward.
OSD Time
SELECT
1. Use
to move OSD Time ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD display time.
4. Press Menu button to return main menu.
English - 13
Special
MENU
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Special ICON.
3. Press SELECT button into the submenu.
Language
MENU
SELECT
1. Use
to move Language ICON.
2. Press SELECT button to select it.
3. Use
to select language.
Factory Reset
SELECT
1. Use
to move the Factory Reset ICON.
2. Press SELECT button to return to default setting.
Information
MENU
SELECT
1. Use
to move the Information ICON.
2. Press SELECT button to select it.
You can know display information
According to the characteristic of video card,
display information can be incorrect
14 - English
English - 15
Adjusting OSD
-CVBS, S-VIDEO MODE
Brightness / Contrast
MENU
Sharpness
(CVBS,S-VIDEO Mode)
SELECT
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Brightness / Contrast ICON.
3. Press SELECT button into the submenu.
1. Press the MENU button to access main menu.
2. Use
to move Sharpness ICON.
3. Press SELECT button to select it.
4. Use
to adjust the sharpness.
(Adjust the clearness of the screen)
Color
Brightness
SELECT
1. Use
to move Brightness ICON.
2. Press SELECT button to select it.
to adjust the brightness of the screen.
3. Use
Contrast
SELECT
1. Use
to move Contrast ICON.
2. Press SELECT button to select it.
3. Use
to adjust the contrast of the screen.
16 - English
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move Color ICON.
3. Press SELECT button into the submenu.
HUE
(CVBS,S-VIDEO Mode)
SELECT
1. Use
to select the HUE ICON.
2. Press SELECT button to select it.
to adjust the HUE.
3. Use
English - 17
Saturation
OSD
(CVBS,S-VIDEO Mode)
SELECT
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move OSD ICON.
3. Press SELECT button into the submenu.
1. Use
to select the Saturation ICON.
2. Press SELECT button to select it.
3. Use
to adjust the saturation.
Preset Color
OSD H-Position
MENU
SELECT
1. Use
to select the Mode 1, and Mode 2.
2. Press the Menu button to return to the previous state.
9300K : Slightly Bluish white.
6500K : Slightly Reddish white.
1. Use
to move OSD H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD left or right.
OSD V-Position
User Color
SELECT
SELECT
MENU
1. Use
to move User color ICON.
2. Press SELECT button to select it.
to increase or decrease each color.
3. Use
18 - English
1. Use
to move OSD V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD upward or downward.
English - 19
OSD Time
Information
MENU
SELECT
1. Use
to move OSD Time ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD display time.
4. Press Menu button to return main menu.
SELECT
1. Use
to move the Information ICON.
2. Press SELECT button to select it.
You can know display information
According to the characteristic of video card,
display information can be incorrect
Language
Special
MENU
MENU
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Special ICON.
3. Press SELECT button into the submenu.
SELECT
1. Use
to move Language ICON.
2. Press SELECT button to select it.
3. Use
to select language.
Factory Reset
SELECT
1. Use
to move the Factory Reset ICON.
2. Press SELECT button to return to default setting.
20 - English
English - 21
Standard Signal Table
Pin assignment table D-Sub
Mini 15pin connector
PC Supported Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Clock Frequency
(MHz)
VGA
(720 X 400)
31.469
70.087
28.322
VGA
(640 X 480)
31.469
59.940
25.175
VGA
(640 X 480)
37.500
75.000
31.500
SVGA (800 X 600)
37.900
60.320
40.000
SVGA (800 X 600)
46.875
75.000
49.500
XGA (1024 X 768)
48.363
60.004
65.000
XGA (1024 X 768)
60.023
75.029
78.750
MAC (640 X 480)
35.000
66.667
30.240
MAC (832 X 624)
49.726
74.551
57.284
Pin No.
Assignment
Red Video
Green Video
Blue Video
N.C
Ground
Red Video Ground
Green Video Ground
Blue Video Ground
Pin No.
10
11
12
13
14
15
Assignment
5V Input
Ground
Ground
SDA
H.Sync
V.Sync
SCL
10
11
15
15pin D-Sub
DVR Supported Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Clock Frequency
(MHz)
NTSC 1 (616 X 452)
31.469
59.940
24.5454
NTSC 2 (680 X 452)
31.469
59.940
27.000
PAL 1 (736 X 544)
31.250
50.000
29.500
PAL 2 (680 X 544)
31.250
50.000
27.000
22 - English
English - 23
Specification
Model
LCD
Panel
H550V(B15AC
Type
Amorphous active matrix super TFT LCD
Screen Size
38.1cm (Diagonal)
Maximum Resolution
1024 X 768 @ 75 Hz
Pixel Range
0.297 mm X 0.297 mm
Display Colors
16.2M Color
Contrast Ratio
300 : 1
Viewing Angle
70째 / 70째 / 55째 / 60째 (Left / Right / Up / Down)
Response Time
25 msec
Luminance
250 cd/m
Synchro Horizontal Frequency
nization Vertical Frequency
Maximum
Power
Consumption Power Saving Mode
Control key Front Part
Input
Signal
Compati
bility
Troubleshooting
Input
60kHz (Max.)
Check the power connection.
(Refer to page 4)
OSD, "check RGB
( CVBS, SVIDEO)"
is displayed on the
screen.
Check the signal cable or signal Source.
(Refer to page 4)
Screen looks to be run
down.
Perform Auto_config.
75 Hz (Max.)
40W
Under 3W
SOURCE, MENU/ EXIT, SELECT, POWER,
-/ , +/ , AUTO
Video : Analog RGB(0.714Vpp)75ohm,
Composite in (BNC),S-VHS in
Connector
15-pin Mini D-sub, Stereo, S-VHS, BNC *1
IBM
VGA,SVGA,XGA
Video
NTSC/PAL standard
Normal&Ergonomic Modes
Power Supply
Wall Mount
Input : 100-240Vac (50/60 Hz), 0.45A
Safety Standard
Safety
Standard
EMI
& EMI
Dimension Size and Weight
UL / C-UL
24 - English
Power LED is dark.
No picture.
Screen is not clear.
Remove attaches to the signal line
(Video extension cable and others)
and switch on.
Perform Auto-config.
Adjust clock and PHASE.
VESA Standard
FCC
352 156 369/ 4.1kg
Display is unstable and
trembling.
Check the resolution and frequency of
computer and video card, and set up
again refer to the current monitor
mode and standard signal mode table.
English - 25
Warning
To prevent damage or loss, please read this warning carefully.
Color is irregular.
Adjust COLOR at User Mode in OSD Color
Menu.
When connecting/disconnecting the plug, pull out
the plug itself, and never pull the cord to prevent fire
caused by short.
Double images or
'ghosts'.
Check the resolution and frequency of
computer and video card, and set up
again in reference to the current monitor
mode and standard signal mode table.
To prevent electric shock, do not connect/disconnect the plug with wet hand.
Picture is dark.
Picture is biased or cut
or too wide.
Adjust COLOR at User Mode in OSD Color
Menu.
If you see smoke or smell something burning, stop
using the unit, switch off the power, pull out the plug,
and then contact your local service station.
To prevent fire, do not connect a large number of
equipments in a single line.
Perform Auto-Config.
To prevent fire and electric shock, pull out the plug in
case of thunder and lightening.
Power LED turns into
Green blinking.
Monitor is in DPMS mode.
To prevent fire and electric shock, do not try to take
the monitor apart or repair it yourself. Contact your
local service station or customer service center for
inspection, modification or repair.
26 - English
English - 27
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 14
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:b4ac5d94-a3b6-11d8-96f1-00031400249a
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Modify Date                     : 2004:05:12 01:55:34+09:00
Create Date                     : 2004:05:12 11:20:33Z
Metadata Date                   : 2004:05:12 01:55:34+09:00
Document ID                     : uuid:b4ac5d87-a3b6-11d8-96f1-00031400249a
Format                          : application/pdf
EXIF Metadata provided by EXIF.tools
FCC ID Filing: MSAB15AC

Navigation menu