Hanwha Techwin DIGIMAXV70 Digital Camera User Manual v70en 02 v03

Samsung Techwin Co Ltd Digital Camera v70en 02 v03

Contents

Users Manual 3 of 3

78
File name
The first stored folder name is 100SSCAM, and the first file name is SA700001.
Whenever you store an image, the file number is increased by 1.
The file numbers are named from SA700001 to SA709999 automatically, 9999 files will
be stored in a folder.
The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM
101SSCAM ~ 999SSCAM.
The files used with the memory card conform to the DCF(Design rule for Camera File
systems) format.
INFORMATION
Even if the batteries or AC adapter are removed and inserted again, the power off
setting will be preserved.
Note that the automatic power off function will not operate if the camera is in PC mode,
slide show, playing back a voice recording or movie clip.
INFORMATION
Auto power off
Setting Power Off
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [PWR SAVE] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
Selecting [OFF] : The power off function will not operate.
Selecting [1~10MIN] : The power will turn off automatically if not used for the period of time
specified.
This function switches the camera off after a set amount of time in order to prevent
unnecessary battery drainage.
SET UP
FILE
PWR SAVE
LANGUAGE
FORMAT
DATE.TIME
BACK: SET:OK
3072
OFF
79
Language
Setting Language
1. In any mode other than Voice Recording mode, press
the MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [LANGUAGE] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
LANGUAGE sub menu
- Type A : English, French, German, Spanish, Italian, Russian, Dutch and Portuguese.
- Type B : English, Korean, Simplified Chinese, Traditional Chinese, Danish, Swedish,
Thai, and Malaysian.
Formatting a Memory Card
1. In any mode other than Voice Recording mode, press
the MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [FORMAT] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [NO] is selected : The memory card will not be formatted. Press the menu button twice
and the menu display will disappear.
If [YES] is selected : A [PLEASE WAIT!] message appears and the memory card will be
formatted. If you ran FORMAT in Play mode, a [NO IMAGE!] message will appear.
Be sure to run [FORMAT] on the following types of memory card.
- A new memory card, or an unformatted memory card.
- A memory card that has a file this camera can t recognize or one that has been taken from
another camera.
Always format the memory card using this camera. If you insert a memory card that has been
formatted using other cameras, memory card readers, or PCs, you will get a [CARD
ERROR!] message.
There is a choice of languages that can be displayed on the LCD monitor. Even if the batteries or
AC adapter are removed and inserted again, the language setting will be preserved.
Formatting a memory card
This is used for formatting the memory card. If you run [FORMAT] on the memory card, all
images, including the protected images, will be deleted. Be sure to download important
images to your PC before formatting the memory card.
SET UP
FILE
PWR SAVE
LANGUAGE
FORMAT
DATE.TIME
BACK: SET:OK
3072
ENGLISH
DANSK
SET UP
FILE
PWR SAVE
LANGUAGE
FORMAT
DATE.TIME
BACK: SET:OK
3072
NO
YES
80
Setting up the Date/ Time/ Date type
You can change the date and time that will be displayed on the captured images and set up
the date type.
There is an option to include DATE/TIME on still images.
Date Imprinting
1. In any mode other than Voice Recording mode, press
the MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [IMPRINT] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Use the UP and DOWN buttons to select the desired
date imprint type, and then press the OK button.
[OFF] : The DATE & TIME will not be imprinted on the image file.
[DATE] : Only the DATE will be imprinted on the image file.
[DATE&TIME] : The DATE & TIME will be imprinted on the image file.
Imprinting the recording date
Setting Date/Time & Selecting Date type
1. In any mode other than Voice Recording mode, press
the MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [DATE. TIME] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Use the UP, DOWN, LEFT, and RIGHT buttons to
select the desired submenu value, and then press the
OK button.
RIGHT button : Selects the year/month/day/hour/minute/date type.
LEFT button : Moves the cursor to the [DATE. TIME] main menu if the cursor is at the
first item of the date and time setup. In all other cases, the cursor will be
shifted to the left of its current position.
UP and DOWN buttons: Changes the setting value.
- Date type
[YY/MM/DD] : year/ month/ day [MM/DD/YY] : month/ day/ year
[DD/MM/YY] : day/ month/ year
SET UP
FILE
PWR SAVE
LANGUAGE
FORMAT
DATE.TIME
BACK: SET:OK
3072
04/ 09/ 01
00:00
YY/MM/DD
SET UP
PWR SAVE
LANGUAGE
FORMAT
DATE.TIME
IMPRINT
BACK: SET:OK
3072
OFF
DATE
DATE & TIME
81
Imprinting the recording date
Function lamp
You can turn on and off the function lamp located on the front of the camera.
Setting the function lamp
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [LAMP] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [OFF] is selected : The function lamp will not light up.
If [ON] is selected : The function lamp will light up.
Description of the Function lamp
Function Description
Power on
Blue light blinks and then turns off when the camera is ready to take a picture.
After taking a picture
Blue lamp blinks once.
While movie recording
Blue lamp blinks at a 1-second interval.
While voice recording Blue lamp blinks at a 1-second interval.
After selecting the remote controller mode
Blue lamp blinks at a 1-second interval.
* The lamp will function while using the self-timer even if the
configuration is set to off the lamp. (See p. 36)
The Date & Time are imprinted at the bottom right side of the still image.
The date will be imprinted as a DATE TYPE setting.
TIME is imprinted in the following way : [Hour : Minute: Second] and hours are shown
using the 24 hour clock.
The imprint function is applied only to still images.
INFORMATION
While the self timer is
functioning
SET UP
LANGUAGE
FORMAT
DATE.TIME
IMPRINT
LAMP
BACK: SET:OK
3072
OFF
ON
82
Sound
If you set the operation sound to ON, various sounds will be activated for camera startup,
when button are pressed, and if there is a card error, so that you can be aware of the camera
operation status.
Setting Operation Sounds
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [SOUND] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [SOUND] sub menu : OFF/ LOW/MEDIUM/ HIGH
You can adjust the LCD brightness.
Adjusting LCD Brightness
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [LCD] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [LCD] sub menu : DARK, NORMAL, BRIGHT
LCD brightness
SET UP
FORMAT
DATE.TIME
IMPRINT
LAMP
SOUND
BACK: SET:OK
3072
OFF
LOW
MEDIUM
HIGH
SET UP
DATE.TIME
IMPRINT
LAMP
SOUND
LCD
BACK: SET:OK
3072
DARK
NORMAL
BRIGHT
83
Selecting Video out type
The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the
camera is connected. PAL mode can support only BDGHI.
Setting the Video Out Type
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [VIDEO] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
- [VIDEO] sub menu : NTSC, PAL
NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland,
Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland,
Thailand, Norway.
When using a TV as an external monitor, you will need to select the external or AV
channel of the TV.
There will be a digital noise on the external monitor, but it is not a malfunction.
If the image is not in the centre of the screen, use the TV controls to centre it.
When using a PAL type monitor, there will be a black frame on the lower part of the
monitor.
When the camera is connected to an external monitor, the menu will be visible on the
external monitor and the menu functions are the same as those indicated on the LCD
monitor.
INFORMATION
Connecting to an external monitor
In RECORDING/ PLAY mode, you can
view the stored still images or movie clips
by connecting the camera to an external
monitor via the A/V cable. When the
camera is connected to an external
monitor, the LCD monitor will be turned off
automatically.
Yellow color-Video
White color-Voice
SET UP
IMPRINT
LAMP
SOUND
LCD
VIDEO
BACK: SET:OK
3072
NTSC
PAL
84
Quick view
If you enable Quick View before capturing an image, you can view the image you just
captured on the LCD monitor for the duration set in the [Q.VIEW] setup. Quick view is
possible only with still images.
Setting Quick View
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [Q.VIEW] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[OFF] : The quick view function can’t be activated.
[1 ~ 5 SEC] : The captured image is briefly displayed during the selected time.
Connecting an External Device (USB)
You can select an external device to which you want to connect the camera using the USB
cable.
Selecting an External Device
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [USB] menu by pressing the UP/ DOWN button
and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
[COMPUTER] : Select this if you want to connect the camera to your PC. Refer to page
107 for instructions on how to connect the camera to your PC.
[PRINTER] : Select this if you want to connect the camera to your printer. Refer to
page 71 for instructions on how to connect the camera to your printer.
SET UP
SOUND
LCD
VIDEO
Q.VIEW
USB
BACK: SET:OK
3072
COMPUTER
PRINTER
SET UP
LAMP
SOUND
LCD
VIDEO
Q.VIEW
BACK: SET:OK
3072
1 SEC
85
Initialization(RESET ALL)
All camera menu and function settings will be restored to their default values. However,
values for DATE/TIME, LANGUAGE, and VIDEO OUT will not be changed.
Initializing the Camera
1. In any mode other than Voice Recording mode, press the
MENU button.
2. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
3. Select the [RESET] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
If [NO] is selected : Settings will not be restored to their defaults.
If [YES] is selected : All settings will be restored to their defaults.
SET UP
LCD
VIDEO
Q.VIEW
USB
RESET
BACK: SET:OK
3072
NO
YES
86
Setting up the MYCAM menu
You can set up a start up image, start up sound and shutter sound. Every camera working
mode (with the exception of Voice recording mode) has the MyCAM menu.
The items indicated by are default settings.
Menu tab Main menu Page
OFF IMAGE 1
IMAGE 2 IMAGE 3
OFF SOUND 1
SOUND 2 SOUND 3
OFF SH.SOUND 1
SH.SOUND 2 SH.SOUND 3
START IMAGE
START SOUND
SH.SOUND
p.86
p.87
p.88
You can select the image that is first displayed on the LCD monitor whenever the camera is
turned on.
Setting a Startup Image
1. In any mode with the exception of Voice Recording
mode, press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MYCAM]
menu tab.
3. Select the [START IMAGE] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
Start up image
Use a saved image for the start-up image with the [LOGO] in the [RESIZE] menu in the
play mode.
The start-up image will not be deleted by deleting all images or [FORMAT] menu.
INFORMATION
Sub menu
* Menus are subject to change without prior notice.
MYCAM
START IMAGE
START SOUND
SH.SOUND
BACK: SET:OK
3072
87
You can select the sound that is activated whenever the camera is turned on.
Start up sound
You can select the shutter sound.
Selecting the Shutter Sound
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MYCAM]
menu tab.
3. Select the [SH.SOUND] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
Shutter sound
Setting the Startup Sound
1. In any mode with the exception of Voice Recording mode,
press the MENU button.
2. Press the LEFT/ RIGHT button and select the [MYCAM]
menu tab.
3. Select the [START SOUND] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/ DOWN
button and press the OK button.
MYCAM
START IMAGE
START SOUND
SH.SOUND
BACK: SET:OK
3072
OFF
SOUND 1
SOUND 2
SOUND 3
MYCAM
START IMAGE
START SOUND
SH.SOUND
BACK: SET:OK
3072
OFF
SH.SOUND 1
SH.SOUND 2
SH.SOUND 3
88
Important notes
Be sure to observe the following precautions!
This unit contains precision electronic components. Do not use or store this unit in the
following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
Do not let the unit come into contact with dust, vinyl goods, or chemicals, such as
insecticides, for an extended period of time.
Sand can be particularly troublesome to cameras.
- Do not let sand get inside the unit when using it on beaches, coastal dunes, or other areas
where there is lots of sand.
- Doing so may result in failure or may permanently render the unit unusable.
Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment, condensation
can form on the delicate electronic circuitry. If this occurs, turn the camera off and wait for at
least 1 hour until all moisture is dispersed. Moisture build up can also occur in the memory
card. If this happens, turn off the camera and remove the memory card. Wait until the
moisture has dispersed.
Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of
the image sensor.
- Pay attention not to get fingerprints or foreign substances on the surface of the lens.
If the digital camera is not used for a long period, an electric discharge can occur.
It is a good idea to remove the batteries and the memory card if you do not intend using the
camera for an extended period of time.
89
Important notes
If the camera is exposed to an electronic interference, it will turn itself off to protect the
memory card.
Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens and LCD assemblies.
If this does not work, lens-cleaning paper with lens cleaning fluid can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come into contact with
solvent materials such as benzol, insecticide, thinners etc. This may damage the body shell
of the camera and also affect its performance. Rough handling can damage the LCD
monitor. Take care to avoid damage and keep the camera in its protective carry case at all
times when not in use.
Do not attempt to disassemble or modify the camera.
Under certain conditions, static electricity can cause the flash unit to fire. This is not harmful to
the camera and is not a malfunction.
When images are uploaded or downloaded, the data transfer may be affected by static
electricity. In this case, disconnect and re-connect the USB cable before trying the transfer
again.
90
Warning indicator
There are several warnings that may appear on the LCD display
Warning indicator Causes Remedy
- Turn off the camera power and turn it
on again
- Insert the memory card again
- Format the memory card (p.79)
- Memory card error
- There is insufficient
memory capacity to take
an image
-
There are no images stored
on the memory card
-
A memory card is not inserted
-
The camera can t
recognize the memory card
- File error
- Memory card error
- There is low battery
capacity
- The memory card is
locked
CARD ERROR !
CARD FULL !
NO IMAGE !
NO CARD !
FILE ERROR !
LOW BATTERY !
CARD LOCKED !
- Insert a new memory card
- Delete unnecessary image files to
free up some memory
- Take images
- Insert a memory card that is holding
some images
- Insert a memory card
- Insert the memory card again
- Turn off the camera power and turn it
on again
- Format the memory card
- Contact a camera service center
- Insert fresh batteries
- SD : Slide the write protect switch to the
top of the memory card
- When taking pictures in
dark places
LOW LIGHT ! - Use a tripod and take pictures in
Flash Photography mode
91
Before contacting a service center
Please check the following
Symptom Causes Remedy
- Insert fresh batteries
- Connect an AC Power Adapter
- Insert the batteries according to the
polarity marks (+, -)
- There is low battery
capacity
- An AC Power Adapter is
not connected
- Batteries are inserted
incorrectly with the
reverse polarities
-
The batteries are exhausted
- The Camera is turned off
automatically
- The Adapter plug is not
connected securely
- The Camera is being
used in low temperatures
- The memory card is not
inserted
- There is insufficient
memory capacity
- The memory card has
not been formatted
- The memory card is
exhausted
-
The camera’s power is off
-
The batteries are exhausted
- The memory card is
locked
- Batteries are inserted
incorrectly with the
reverse polarities
The camera
doesn t switch on
The camera
power ceases
whilst in use
Batteries drain
quickly
Camera does
not take images
when pressing
the Shutter
button
- Insert fresh batteries
- Press the power button to reactivate
camera
- Remove and re-insert the plug
- Keep the camera in warm conditions
(i.e. inside a coat or jacket) and only
remove it in order to take images
- After turning the camera off, insert a
new memory card
- Delete unnecessary image files
- Format the memory card (p.79)
- Insert a new memory card
- Turn the camera power on
- Insert fresh batteries
- Refer to [CARD LOCKED!] error
message (p.90)
- Insert the batteries according to the
polarity marks (+, -)
- The camera was stopped
due to a malfunction
The camera
suddenly stops
working while in
use
- Remove /re-insert batteries and switch
the camera on
92
Before contacting a service center
Symptom Causes Remedy
- A picture was taken
within 0.8 m from the
subject without setting an
appropriate macro mode
- Taking a picture beyond
the flash range
- The lens is smudged or
dirty
- Flash off mode has been
selected
The images are
unclear
The flash does
not fire
- If the subject is closer than 0.8m,
select macro shot mode
- Take a picture within the flash range
- Clean the lens
- Dis-engage flash off mode
- Reset the date and time correctly
- The date and time have
been set incorrectly or
the camera has adopted
the default settings
- Camera malfunction
- Incorrect memory card
format
Incorrect date
and time is
displayed
The camera
buttons do not
operate
A card error has
occurred while
the memory
card is in the
camera.
- Remove /re-insert batteries and switch
the camera on
- Re-format the memory card (p.79)
- Incorrect file name
(Violation of DCF format)
The images
don't play back
- Do not change the image file name
93
Before contacting a service center
Symptom Causes Remedy
- White balance setting is
incorrect
- Exposure is excessive
- Cable connection is
incorrect
- The camera is off
- There are no batteries,
the batteries are
exhausted or the AC
adapter is not connected.
- The operating system is
not Windows 98, 98SE,
2000, ME, XP/ Mac OS
9.0 ~ 10.3. Alternatively
the PC does not support
USB
- The camera driver is not
installed
Colour of image
is different to
the original
scene
Images are too
bright
When using the
PC’s explorer,
the [Removable
Disk] file does
not show
- Select appropriate White balance
- Reset exposure compensation
- The external monitor has
not been connected
properly with the camera
- There are incorrect files
in the memory card
No image on
external monitor
- Check the connection cables
- Insert a memory card that has correct
files
- Check the connection
- Turn the camera on
- Insert new batteries or check the
adapter connection
- Install Windows 98, 98SE, 2000, ME,
XP/ Mac OS 9.0 ~ 10.3 to PC that
supports USB
- Install a [USB Storage Driver]
94
Specifications
Type 1/1.8" CCD
Effective Pixel Approx. 7.0 Mega-pixel
Total Pixel Approx. 7.4 Mega-pixel
Schneider Lens f = 7.7 ~ 23.1mm
(35mm film equivalent : 38~114mm)
F No. F2.7 ~ F4.9
Still Image mode : 1.0X ~ 5.0X
Play mode : 1.0X ~ 12.0X (depends on image size)
Optical Viewfinder
Real image optical viewfinder
LCD Monitor 2.0" color TFT LCD(117,600 dots, Rotating LCD)
Type TTL auto focus, Manual focus
Normal : 80cm ~ infinity
Macro : 4 ~ 80cm (Wide), 30 ~ 80cm (Tele)
Type Mechanical and Electronic shutter
Speed
2 ~ 1/2,000 sec. (Manual, Night Scene Mode : 15 ~ 1/2,000 sec.)
Program AE, Shutter Priority AE, Aperture Priority AE or Manual Exposure
Metering : Multi, Spot
Compensation 2EV (0.5EV steps)
ISO Equivalent Auto, 50, 100, 200, 400
Modes
Auto, Auto & Red-eye reduction, Slow sync., Fill-in flash, Flash off
Range Wide : 0.3 ~ 3.0m, Tele : 0.3 ~ 2.0m
Recharging Time
Approx. 6 sec.
Sharpness Soft, Normal, Vivid
Effect Normal, B&W, Sepia, NEGATIVE ,RGB
White Balance
Auto, Daylight, Cloudy, Fluorescent_L, Fluorescent_H, Tungsten, Custom
Voice Recording (max. 1 hour)
Voice Memo in Still Image (max. 10 sec.)
Date Imprinting Date &Time, Date, Off (user selectable)
Modes : Auto, Program, Myset, A/S/M, Voice, Night Scene, Scene
*
Scene : Portrait, Children, Landscape, Close-up, Sunset, Dawn,
Backlight, Fireworks, Beach & Snow, TEXT
Continuous : Single, Continuous, AEB
Self-timer : 2 sec., 10 sec., Remote control (optional)
With Audio (recording time : memory capacity dependent)
Size : 640x480, 320x240
Frame rate : 30 fps, 15 fps
SD / MMC Card (up to 512MB guaranteed)
Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0
Movie Clip : MOV (MPEG-4) Audio : WAV (G.711)
Image Sensor
Lens
Focal Length
Range
Control
Digital Zoom
Viewfinder
Focusing
Shutter
Exposure
Flash
Voice Recording
Shooting
Storage
Movie Clip
Still Image
Media
File Format
95
Specifications
3072 : 3072X2304 pixels, 2816 : 2816X2112 pixels,
2592 : 2592x1944 pixels, 2272 : 2272x1704 pixels,
2048 : 2048x1536 pixels, 1600 : 1600x1200 pixels,
1024 : 1024x768 pixels, 640 : 640x480 pixels
3072 : TIFF 1, S.Fine 8, Fine 16, Normal 24
2816 : TIFF 1, S.Fine 10, Fine 19, Normal 29
2592 : TIFF 1, S.Fine 11, Fine 23, Normal 35
2272 : TIFF 2, S.Fine 15, Fine 30, Normal 45
2048 : TIFF 3, S.Fine 18, Fine 36, Normal 53
1600 : TIFF 5, S.Fine 30, Fine 61, Normal 91
1024 : TIFF 12, S.Fine 70, Fine 130, Normal 183
640 : TIFF 29, S.Fine 183, Fine 305, Normal 457
*
These figures are measured under Samsung’s standard conditions
and may vary depending on shooting conditions and camera settings.
Single image, Thumbnails, Slide show, Movie clip
Trimming, Resizing
Digital output connector : USB 2.0
Audio : Mono
Video output : NTSC, PAL (user selectable)
DC power input connector : 5.0V
Primary battery : 2xAA alkaline(High capacity), Lithium, Ni-Mn(High capacity),
Ni-Zn(High capacity) / 1xCR-V3
Rechargeable battery : 3.7V Li-ion (SLB-1437), 2xAA Ni-MH(Over 2300mAh),
Ni-Cd(Over 1100mAh) / 1xI-Pack (SBP-1303)
AC Adapter : SAC-51
* Included power source may vary depending on sales region.
Dimensions (WxHxD) 106.5 x 57 x 38.5 mm
Weight 190g (without batteries and card)
Operating Temperature 0 ~ 40
Operating Humidity 5 ~ 85 %
Storage Driver (Windows98/98SE/2000/ME/XP, Mac OS 9.0 ~ 10.3)
Digimax Viewer, QuickTime Player, ArcSoft PhotoImpression, Digimax Reader
* Specifications are subject to change without prior notice.
* All trademarks are the property of their respective owners.
Capacity
(32MB)
Image Size
Storage
Interface
Image Play Type
Editing
Power Source
Special Features
Software Camera Driver
Application
MPEG-4 VGA Class 30fps Movie Clip
2.0
"
Rotating LCD Monitor
A Unique Function : 9 Different Power Source
Convert Scanned Text Images into Editable Document
A World Superior Schneider Lens
4cm Macro
96
Software Notes
Please ensure that you read the instruction manual carefully before use.
The attached software is a camera driver and image editing software tool for Windows.
Under no circumstances should all or part of either the software or the user manual be
reproduced.
Copyrights for software are licensed only for use with a camera.
In the unlikely event of a manufacturing fault, we will repair or exchange your camera.
We cannot, however, be held responsible in any way for damage caused by inappropriate
use.
Using a Hand-made PC or a PC and OS that has not been guaranteed by the manufacturer is
not covered by the Samsung warranty.
Before reading this manual, you should have a basic knowledge of computers and O/S
(Operating Systems).
System Requirements
For Windows For Macintosh
Power Mac G3 or later
Windows 98/98SE/2000/ME/XP Mac OS 9.0 ~ 10.3
Minimum 32MB RAM (XP : 128MB) Minimum 64MB RAM
140MB of available hard-disk space 110MB of available hard-disk space
USB port USB port
CD-ROM drive CD-ROM drive
QuickTime 6.0 or later for Movie Clip
PC with processor better than MMX
Pentium 233MHz (XP : Pentium II 300MHz)
800x600 pixels, 16-bit colour display
compatible monitor (24-bit color display
recommended)
97
About the software
Camera driver : This enables images to transfer between the camera and PC.
This camera uses the USB Storage Driver as the camera driver. You can use the camera as
a USB card reader. After installing the driver and connecting this camera to the PC, you can
find [Removable Disk] in [Windows Explorer] or [My computer]. A USB Storage Driver is
provided only for Windows. A USB Driver for MAC is not included with the Application CD.
But you can use the camera with Mac OS 9.0 ~ 10.3.
QuickTime Player : The program for playing back QuickTime movies (.mov). It can also play
video files compressed with MPEG4 codec.
Digimax Viewer : This is a program for viewing stored images.
You can see the stored images in the memory directly on a PC monitor. You can also copy,
move or delete the images and enlarge/downscale the image sizes with Digimax Viewer.
This software is only compatible with Windows.
PhotoImpression : Image editing program.
You can edit or store still images that you download from the camera. This software is only
compatible with Windows.
Digimax Reader : Text recognition program
You can save an image file that was captured in the TEXT mode as a text file with this
program. This software is only compatible with Windows.
* Be sure to check the system requirements (page 96) before installing the driver.
* You should allow 5~10 seconds for running the automatic setup program according to the
capability of the computer. If the frame does not show, run the [Windows Explorer] and select
[Samsung.exe] in the CD-ROM Drive root directory.
After inserting the CD-ROM provided with
this camera into the CD-ROM drive, the
following window will automatically run.
Before connecting the camera to the PC,
you should first install the camera driver.
98
Setting up the application software
To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to the PC and can be
edited by an image editing program.
You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
Close other programs before installing the application software.
Before installing the application software, disconnect the USB connection.
INFORMATION
4. A Welcome window will appear.
Click [Next >] to proceed to the next screen.
[Click !]
1. Click the [Install] menu in the Autorun frame.
The camera driver is installed automatically.
2. Installation is complete.
Click the [Finish] button.
3. Click [Next >] to begin installing QuickTime.
[Click !]
[Click !]
[Click !]
99
Setting up the application software
5. The Software License Agreement window will open, asking
you to agree to the licensing. Use the button on the bottom
left to select the language of your choice, and then click
[Agree] to accept the license agreement. The installation
will proceed to the next stage. If you do not agree to the
license agreement, click [Disagree]. The installation will be
canceled. If the language of your choice is not listed, please
select [English].
6. A window will open, asking you to select a destination
folder where the files will be copied to. Click [Next >]. To
copy the files to another folder, click [Browse..] to select a
folder you want to copy the files to.
7. The Choose Installation Type window will open.
Click [Next >].
[Minimum] : Installs required files only.
[Recommended] : Installs required files and the most
commonly used optional files.
[Custom] : Allows you to install only the
components you choose.
8. A window will open, asking you to choose a folder to which
program icons will be added. Click [Next >]. If you want to
add the program icons to a different folder, choose another
folder, and then click [Next >].
[Click !]
[Click !]
[Click !]
9. The Enter Registration window appears.
Enter your name and organization in the respective fields,
and then click [Next >].
You do not have to enter a registration number.
[Click !]
100
Setting up the application software
13. Specify the file types you want to
associate with QuickTime. Click [Finish].
14. Installation is complete. Click [Close].
11. Set the transfer rate for downloading
content from the Internet, and then click
[Next >].
12. Set up your browser for QuickTime plug-in.
Click [Next >].
The QuickTime program folder will appear.
Click on the Close button to close the folder.
10. The QuickTime Settings - Introduction
window appears. Click [Next >].
[Click !]
[Click !]
[Click !][Click !]
[Click !]
[Click !]
101
Setting up the application software
16.
The [Digimax Viewer 2.1] installation window will be
displayed as shown alongside. Click the [Next] button.
[Click !]
If you select [Cancel] at step 16, a window for installing PhotoImpression will be
displayed.
INFORMATION
15. A window where you can choose the program you want
to install will appear. Click [Install]. For information on
application software, please refer to page 97.
* The QuickTime Player will launch, the readme file will open, and the Step 15 window will open.
Click on the Close 1 and Close 2 buttons to exit the program.
If you select [Cancel] , the application program installation will be cancelled.
17. The Software License Agreement window will be
displayed. If you agree to this, click [Yes], the window will
then move to the next step. If you disagree, click [ No ]
and the installation program will be canceled.
[Click !]
[Click !]
[Close 1
button]
[Close 2
button]
102
Setting up the application software
18. A destination selection window will open.
Click [Next >]. To copy to the files to another
folder, click [Browse..] and choose a folder
you want.
[Click!]
19. A window will open, asking you to choose a
folder to which program icons will be added.
Click [Next >] button.
If you want to add the program icons to a
different folder, choose another folder, and
then click [Next >] button.
If you select [Cancel] at step 21, a window for installing Digimax Reader will be
displayed.
INFORMATION
[Click!]
20. Digimax Viewer installation is successfully
completed. Click the [Finish] button to install
PhotoImpression.The system will not reboot
even the [Yes, I want to restart the computer
now] option is selected.
*The frame 20 may not appear according
to the system requirements. [Click!]
21. Digimax Viewer Installation is completed.
The PhotoImpression installation window will
be displayed as shown alongside.
Click the [OK] button.
[Click!]
22. A Welcome window will be displayed.
Click the [Next >] button.
[Click!]
103
Setting up the application software
23. The Software License Agreement window
will be displayed. If you agree to this, click
[Yes], the window will then move to the next
step. If you disagree, click [No] and the
installation program will be canceled.
[Click!]
24. A destination selection window will open.
Click [Next >]. To copy to the files to another
folder, click [Browse...] and choose a folder
you want.
[Click!]
25. The [Select Components] window will
appear. Click [Next >] button.
[Click!]
26. A window will open, asking you to choose a
folder to which program icons will be added.
Click [Next >] button.
If you want to add the program icons to a
different folder, choose another folder, and
then click [Next >] button. [Click!]
104
Setting up the application software
27. PhotoImpression Installation is completed.
Click the [Finish] button and Digimax Reader
installation will be started. The system will
not reboot even the [Yes, I want to restart
the computer now] option is selected.
*The frame 27 may not appear according to
the system requirements. [Click!]
28. A window will be displayed as shown alongside.
Click the [INSTALL] button.
- Check the [MANUAL] button. Instructions for using
Digimax reader will be displayed.
- Click the [EXIT] button and Digimax reader installation will
be canceled and the Restart window will appear.
29. A window will open.
Click the [Next(N)>] button.
30. The Software License Agreement window will be
displayed. If you agree to this, click [Yes], the window will
then move to the next step. If you disagree, click [No] and
the installation program will be canceled.
31. A destination selection window will open. Click [Next >].
To copy to the files to another folder, click [Browse...] and
choose a folder you want.
[Click!]
[Click!]
[Click!]
[Click!]
105
Setting up the application software
32. Installation is complete. To apply changes,
you must restart the computer. Select [Yes, I
want to restart my computer now], and then
click [OK].
33. After restarting the computer, connect the PC to the camera with the USB cable.
35. If you can see [Removable Disk] under
[My computer], the camera driver installation
was successful.
Now you can transfer image files from the
camera to PC via the USB cable.
[Click!]
*The frame 32 may be displayed according the
system requirements. Click the [Finish] button
to restart the computer.
[Click!]
34. Turn the camera power on.
[Found New Hardware Wizard] will open and
the computer will recognize the camera.
If you have ever installed an image viewer
program or your OS is Windows XP, an
image viewer program will open.
If the image viewer program opens, the
camera driver was setup successfully.
106
Setting up the application software
If you have installed the camera driver, [Found New Hardware Wizard] may not open.
On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens
and a window asking you to select a driver file may appear. In this case, specify "USB
Driver" in the CD supplied. (for Windows 98 and 98 SE).
When connecting the camera to your PC, it is recommended that you use an AC power
adapter.
Before connecting the camera to the PC, You should first install the camera driver.
After installing the camera driver, you have to restart your PC.
If you connect the camera to the PC before installing the camera driver, the [Found New
Hardware Wizard] will open.
In this case, cancel the [Found New Hardware Wizard] and disconnect the camera.
Install the camera driver and connect the camera to the PC again.
Should the computer not find the camera driver after installation, please try one or more
of the following measures.
1. Delete the camera driver (p.110), and re-install the driver.
2. Refer to FAQ (p.119) to check for a possible solution to the problem.
3. If your PC’s central processing unit is VIA chip (This is shown in the USB Host
Controller), download the patch file from the Samsung Camera web page.
(http://www.samsungcamera.com)
INFORMATION
107
Starting PC Mode
The camera driver must be installed before using PC mode.
To save battery power, it is recommended that you use an AC adapter (Optional) when
connecting the camera to a computer.
INFORMATION
If you connect the USB cable to a USB port on your PC and then turn on the power, the
camera will automatically switch to "computer connection mode".
In this mode, you can download stored images to your PC through the USB cable.
The LCD monitor is always turned off in PC mode.
The auto focus lamp will blink when the files are transferring via the USB connection.
Connecting the camera to a PC
1. Turn the PC power on.
2. Turn the camera power on.
3. In any mode other than Voice Recording mode, press
the MENU button.
4. Press the LEFT/ RIGHT button and select the [SETUP]
menu tab.
5. Select the [USB] menu by pressing the UP/ DOWN
button and press the RIGHT button.
6. Use the UP and DOWN buttons to select
[COMPUTER], and then press the OK button.
7. Press the menu button twice and the menu will disappear.
8. Connect the PC and the camera via the USB cable.
- Insert the small plug of the USB cable into the camera USB connection terminal.
- Insert the large connector of the USB cable into the USB port of the PC.
- The plugs must be firmly inserted.
Disconnecting the camera and PC : Refer to page 112 (Removing the removable disk).
If you selected [PRINTER] in Step 6,
when you connect the camera to your
computer, the [PLEASE WAIT, USB I/F
PRINTER] message will be displayed on
the LCD monitor and the connection will
not be established. In this case,
disconnect the USB cable, and then
follow the procedure from Step 3 and
onward.
SET UP
BACK: SET:OK
SOUND
LCD
VIDEO
Q.VIEW
USB
COMPUTER
PRINTER
108
Starting PC Mode
3. Select an image and press the right mouse
button.
4. A pop-up menu will open.
Click [Cut] or [Copy] menu.
- [Cut] : cuts a selected file.
- [Copy] : copies files.
Downloading stored images
You can download the still images stored on the camera to your PC's hard disk and print
them or use a photo editing software to edit them.
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My computer] and double click [Removable
Disk DCIM 100SSCAM].
The image files will then be displayed.
5. Click a folder where you want to paste the file.
109
Starting PC Mode
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
7. An image file is transferred from the camera to
your PC.
- By using [Digimax Viewer], you can see the stored images in the memory directly on the PC
monitor and you can copy or move the image files.
110
Removing the USB Driver for Windows 98SE
To remove the USB driver, refer to the process shown below.
1. Trace [Start Settings] and click [Control Panel].
[Click !]
4. Uninstallation is complete.
Click the [Finish] button and the window will
disappear.
2. Double-click [Add/Remove programs].
3. The [Add/Remove Programs Properties] window
will open. Click [Digimax V70] and click the
[Add/Remove] button.
[Click !]
111
Removable Disk
To use this camera as a Removable Disk, install (p.98) the USB Driver.
1. Before turning the camera power on, connect the camera to the PC with the USB cable.
2. Click [Removable Disk] under [My computer] or [Windows Explorer].
3. Image files stored in the Removable Disk (DCIM 100SSCAM) can be transferred to the
PC.
Important information whilst using the Removable Disk
The [Removable Disk] indicator will not show when the camera power is off or the USB
cable is removed.
We recommend that you should copy the images to the PC to view them. Opening
images directly from the removable disk may be subject to unexpected disconnection.
When uploading images from the PC to the camera, ensure that the uploaded file
names are not the same as those already stored on the memory.
When you upload a file that is not taken by this camera to Removable Disk, the [FILE
ERROR!] message will be displayed on the LCD monitor in the PLAY mode, and
nothing is displayed in THUMBNAIL mode.
The auto focus lamp will blink, when a file is
transferred (copy or deletion) between the PC
and the camera. Do not remove the USB cable
until the lamp stops blinking. To remove the USB
cable in Windows 2000/ME/XP, use the [Unplug
or Eject Hardware] icon on the task bar.
If your PC wasn't patched with Windows 2000 Service Packs 4, the USB 2.0 does not
operate properly. In this case, you have to download and install the Windows Service
Packs 4.
INFORMATION
112
Removing the removable disk
[Click!]
[Double-click!]
[Click!]
[Click!]
Windows 98SE
1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you
have to wait until the lamp illuminates.
2. Unplug the USB cable.
Windows 2000/ME/XP
(The illustrations may be different from the real display in accordance with the Windows O/S.)
1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you
have to wait until the lamp illuminates.
2. Double-click the [Unplug or Eject Hardware]
icon on the task bar.
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage Device]
and click the [Stop] button.
4. The [Stop a Hardware device] window will
open. Select the [USB Mass Storage Device]
and click the [OK] button.
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
113
Removing the removable disk
1. A USB Driver for MAC is not included with the software CD as MAC OS supports the
camera driver.
2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This
camera is compatible with MAC OS 9.0 ~ 10.3.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to the MAC.
Using the USB Driver for MAC
Setting up the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be displayed.
2. Select an image file and copy or move it to MAC.
For Mac OS 10.0 or later : First complete uploading from computer to camera and then
remove the removable disk with the Extract command.
CAUTION
6. A [Unplug or Eject Hardware] window will
open. Click the [Close] button and the
removable disk will be removed safely.
7. Unplug the USB cable.
[Click!]
114
Digimax Viewer 2.1
This software is only compatible with Windows.
1. To open Digimax Viewer, click the [Start Programs
Samsung Digimax Viewer 2.1 Digimax Viewer
2.1 ] and Digimax Viewer 2.1 will then open.
3. You can easily use the Digimax viewer 2.1 program as
it offers a FILE menu and TOOL bar.And, you can use
the pop up menu. Click an image and press the right
mouse button.
Digimax Viewer functions are listed below.
- Basic functions : Copy, Move, Delete, Rotate, Rename, changing file type, Resize,
Property.
- Advanced functions : Print, Slide show, Export, Sending e-mail, On-line print, Web album etc.
2. If the [Auto Launch] option is selected, this program will be executed automatically with
recognizing the camera.
Before deleting images from the camera, you should download images to your
computer that you wish to keep.
Refer to the [Help] menu in Digimax viewer 2.1 for further information.
INFORMATION
115
Using PhotoImpression
You can use PhotoImpression to perform the following tasks.
With PhotoImpression, you can edit or store still images that you downloaded from the camera.
This software is only available in Windows version.
To start the program, click [Start Programs ArcSoft PhotoImpression PhotoImpression].
The following screen will appear.
[ Command Button ]
[ Tool Bar ]
Command Button
[ Help Button ]
Button Description
Imports a picture from an album, a source folder, or the camera/scanner, or
captures screen shots of what is being viewed on the current monitor.
Selects Cut, Resize, Edit Image, Insert Text, Enhance Picture, Insert
Effects, or Layer.
Performs Insert Frame, Insert Borders, Insert Calendar, Insert Greeting
Cards, Insert Template, or Connect with Other Software.
Saves the edited picture, and sends an e-mail or uses it as the background
image.
Outputs the edited picture according to your preferences.
116
Using PhotoImpression
For detailed instructions on how to use PhotoImpression, please refer to the program's
Help.
INFORMATION
Tool Bar
Digimax Reader is a Text recognition program. You can save an image file that is captured in
the Text mode, as a text file with this program.
This software is only compatible with Windows.
To start the program, click [Start Programs Digimax Reader Eng].
The following screen will appear.
Digimax Reader
Button Description Button Description
Resize Layer
Flip Layer Horizontally
Undo
Copy
Delete Layer
Rotate Layer
Rotate All Layers
Redo
Paste
Close Picture
117
Digimax Reader
How to use the Digimax Reader
1. Connect the camera and the PC with a USB cable and download the images that were
stored in the camera to the PC.
* Please see page 107 ~ 109 for details on Connecting a camera and PC, Downloading
images.
2. Run the Digimax Reader.
3. Click the Open( ) icon as shown alongside.
4. Select the image you want to save as a text file.
* Only an image that was taken with SAMSUNG
camera can be opened.
5. Click the Area Analysis( ) icon to scan the
image.
6. Part of the image you selected will be displayed as
shown.
7. Click the Character Recognition( ) icon.
The part selected in the previous step will be
recognized as text.
118
Please check the following if the USB connection malfunctions.
[Case 1] The camera power is off.
Turn the camera power on. We recommend using an AC power adapter in PC mode.
[Case 2] USB Driver is not installed correctly.
Install the USB Driver correctly. Refer to page 98.
[Case 3] The USB cable is not connected or you are using a cable with an incorrect
specification.
Use a USB cable with the correct specification.
[Case 4] The camera is not recognized by your PC.
Sometimes, the camera may appear under [Unknown Devices] in Device
Manager.
Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable again, and
then turn on the camera.
[Case 5] There is an unexpected error during file transfer
Turn the camera power off and on again. Transfer the file again.
Digimax Reader
To get an image that can be recognized as a text :
- Keep a distance of 20cm between the subject and the camera.
- The subject need to be centered.
- Avoid the camera shake to get a good image.
Refer to the [Help] menu in Digimax Reader for further information.
INFORMATION
8. To save the section as a text, click the Save( )
icon. A window as shown alongside will be
displayed.
9. Select a file type that you want to.
Selectable file type : *.TXT, *.HWP, *.DOC, *.RTF
FAQ
119
FAQ
Please check the following if the USB connection malfunctions.
[Case 6] How do I know my computer supports a USB Interface?
Check the USB port in your computer or keyboard.
Check the OS version. A USB Interface is available in Windows 98, 98SE,
2000, ME .XP.
Check [Universal Serial Bus controllers] in Device Manager. Do the following to
check [Universal Serial Bus controllers].
Win 98/ME : Trace [Start Settings Control Panel System
Device Manager Universal Serial Bus controllers].
Win 2000 : Trace [Start Settings Control Panel System
Hardware Device Manager Universal Serial Bus
controllers].
Win XP : Trace [Start Control Panel System Hardware
Device Manager Universal Serial Bus controllers].
There must be USB Host Controller and USB root hub under [Universal Serial
Bus controllers].
In addition, double-click on the USB Universal Host Controller and the USB
Root Hub to check if the Device Status states "This device is working properly".
If the Device Status says the device is "not working properly", click the "Driver"
tab and then click [Update Driver] or [Reinstall Driver].
When all the conditions mentioned above are met, the computer can support
the USB interface.
[Case 7] When using the USB hub.
There may be a problem in connecting the camera to the PC through the USB
hub if the PC and the hub are not compatible. Wherever possible, connect the
camera to the PC directly.
[Case 8] Are other USB cables connected to the PC?
The camera may malfunction when it is connected to the PC at the same time
as another USB cable. In this case, disconnect the other USB cable, and
connect only one USB cable to the camera.
[Case 9]
When I open the Device Manager (by clicking Start (Settings) Control Panel
(Performance and Maintenance) System (Hardware) Device Manager),
there are Unknown Devices or Other Devices entries with a yellow question
mark(?) beside them or devices with an exclamation mark(!) beside them.
Right-click on the entry with the question(?) or exclamation (!) mark and select
"Remove". Restart the PC and connect the camera the again. For Windows 98 PC,
remove the camera driver also, restart the PC, and then reinstall the camera driver.
Double-click on the entry with the question (?) or exclamation (!) mark, click the
"Driver" tab, and click [Update Driver] or [Reinstall Driver]. If a message appears
asking you to specify the location of the appropriate device driver, specify "USB
Driver" in the CD supplied.
6806-2400
SAMSUNG TECHWIN CO., LTD.
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8086,8088, 8090, 8092, 8099
FAX : (82) 31-740-8398, 8111
www.samsungcamera.com
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
HEADQUARTERS
40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A.
TEL : (1) 201-902-0347
FAX : (1) 201-902-9342
WESTERN REGIONAL OFFICE
18600 BROADWICK ST.,
RANCHO DOMINGUEZ, CA 90220, U.S.A.
TEL : (1) 310-900-5263/5264
FAX : (1) 310-537-1566
www.samsungcamerausa.com
SAMSUNG OPTO-ELECTRONICS UK LIMITED
SAMSUNG HOUSE
1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
FAX : 002711 4619110
www.samsungcamera.co.uk
SAMSUNG OPTO-ELECTRONICS GMBH
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS., GERMANY
TEL : (49) 6196 66 53 03
FAX : (49) 6196 66 53 66
www.samsungcameras.de
SAMSUNG FRANCE S.A.S.
BP 51 TOUR MAINE MONTPARNASSE
33, AV .DU MAINE
75755, PARIS CEDEX 15, FRANCE
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27(Numéro Vert-Appel Gratuit)
TEL : (33) 1-4279-2282/4
FAX : (33) 1-4320-4510
www.samsungphoto.fr
SAMSUNG TECHWIN MOSCOW OFFICE
RUSSIA, 125167, MOSCOW LENNINGRADSKY,
PR-KT, 37-A, KORP14
TEL : (7) 095-258-9299/96/98
FAX : (7) 095-258-9297
http://www.samsungcamera.ru
TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.
7 PINGCHANG ROAD NANKAI DIST., TIANJIN
P.R CHINA
POST CODE:300190
TEL : (86) 22-2761-8867
FAX : (86) 22-2761-8864
www.samsungcamera.com.cn
Internet address - http : //www.samsungcamera.com/
The CE Mark is a Directive conformity
mark of the European Community (EC)

Navigation menu