Hanwha Techwin SEW3040W Wireless Baby Monitor User Manual Part 3

Download:
Mirror Download [FCC.gov]
Document ID	2294847
Application ID	uHRp4p1oEdgk/L+esyZ6SA==
Document Description	User Manual Part 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	77.75kB (971865 bits)
Date Submitted	2014-06-13 00:00:00
Date Available	2014-06-13 00:00:00
Creation Date	2014-05-19 14:46:05
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-06-13 16:57:22
Document Title	User Manual Part 3
Document Creator	Microsoft® Word 2010
Document Author:	n

Overview
Getting to know your Monitoring system
Wireless Monitor
After opening the box, fully charge the monitor before use. After initial charge, recharge as needed.
Front Controls
MENU Button
Monitor Antenna
Press to access from video monitor mode to menu
mode operation. In menu mode, press this button will go
back to monitor mode with save from selection.
Receives and sends signals from or to the camera.
SLEEP Button
Power LED
Used to turn on / off the screen by press this button.
User can turn on the video again by pressing any buttons.
If camera is disconnected, monitor screen would be
turned on automatically in Sleep mode.
Indicator turns green when powered.
When battery is charging, this LED will in green color.
Sound Level LEDs
Microphone
Flashes when sound is detected.
When there are pairing between monitor and camera,
There is a function of transmission of audio only.
SEW-3036W
4.3” LCD Screen
Navigation Controls / oK/ZooM Button
Displays video from the camera.
SEW-3036W
—— Navigation Controls /
Button
Viewing Mode: The following controls are used while watching live video from the camera:
• Press the [$] or [%] buttons to increase or decrease the volume.
• Press the [+] button to switch to the next connected camera’s screen or enter SCAN
mode.
• Press the [
] button to zoom in / out the screen.
10 · Overview
Use the controls to move and select while in Viewing
Mode, Menu Mode and Zoom Mode.
Menu Mode: Use the [$/%/_/+] button arrows to navigate in Menu Mode.
] button to confirm the menu selection.
Press the [
Zoom Mode: While in zooming, use [$/%/_/+] button to move the screen around.
Back Controls
TALK Button
Press down and hold the button to talk back to the camera.
TALK
Kick Stand
Speaker
Use to hold the monitor onto a table.
Produces the sound transmitted from the camera(s).
- ON
- VOX
- OFF
04
nn `` You must have more than one camera configured on the system when using the functions that requires more than one camera.
Overview
Side Controls
Power and VOX ON / OFF Slide Switch
Set this switch to ON or OFF to turn on/off the wireless monitor,
and set to VOX to turn on the VOX mode.
DC 6V Power Input
Connect the included AC power adapter to power and/or
charge the monitor battery.
(when the monitor is not placed in the optional Charge cradle).
English · 11
Wireless Camera
Front & Back Controls
IR LEDs
Camera Antenna
Infrared LED’s provide viewing in no / low light
conditions.
Microphone
Receives sounds for the area near the camera, and
transmits sound from the camera to the monitor.
Sends & receives signals to or from the monitor.
- ON
- OFF
DC 6V Power Input
- ON
- OFF
DC IN 6V
DC IN 6V
Connect the adapter to the camera.
Speaker
Produces the sound transmitted from the monitor.
Side Controls
PAIRING Button
Power LED
Press this button to pair with a monitor.
LED turns on when powered.
Power Slide Switch
Turns the camera ON or OFF.
12 · Overview
PAIRING
PAIRING
Night vision sensor
Detects light levels where the camera is placed.
Installation
How to Install
1.
2.
CAUTION: If you use the system to watch a young child, do not place the camera in the
child's reach.
Wireless Monitor
1.
Place the monitor in a place that will have clear
reception with your camera(s).
2.
Pull out the stand.
``
``
Use the drilling template to drill holes on the wall
for camera installation. (Page 17)
The camera can also be placed on a flat surface, such as a table or shelf, and no
mounting hardware is required.
Adjust the viewing angle of the camera.
When adding cameras that were not included in
the original box, you will need to pair up the
cameras with the monitor.
Installation
can install additional cameras (maximum of
nn `` You
4 cameras).
05
3.
Before you install the camera, carefully plan where and how it will be positioned, and
where you will route the cable that connects the camera to the power adapter.
Before starting permanent installation, verify its performance by observing the image
on the monitor when camera is positioned in the same location/position where it will be
permanently installed and the monitor is placed in the location where it will be used
most of the time.
Mount the camera to the wall.
Mark the position of the screw holes on the wall,
and drill holes and insert 2 screws, then firmly
attach the camera to the wall by placing the
stand over the installed screws and pushing the
base downwards.
install on a concrete wall, drill a hole and use
nn `` Toplastic
anchor to fix.
not pull up the stand lever with an excessive
nn `` Do
force.
Wireless Camera
Carefully unpack the camera.
If you are installing cameras that did not come with the system, please see the
pairing camera section of this manual for details on installation.
Installation Warnings
Aim the camera(s) to best optimize the viewing area: Select a location for the camera
that provides a clear view of the area you want to monitor, which is free from dust, and
is not in line-of-sight to a strong light source or direct sunlight.
Avoid installing the camera where there are thick walls or obstructions between the
camera and the monitor.
STRANGULATION HAZARD - Keep cord out of child's reach. NEVER place camera or
cords within 3 feet of crib or playpen. Never use extension cords with AC Adapters.
Only use the AC Adapters provided.
English · 13
Appendix
Item
Specifications
Operating Humidity Range
85% RH
Regulation Compliance
FCC/CE
Environment Rating
Item
Details
Wireless Camera
Details
Indoor use only
RoHS Compliance
Yes for CE version only
Audio
Built in Microphone/ Speaker
Weight
122g
Display Type/Size
Color TFT 4.3”
GFSK
Resolution (Pixel)
480X272 (RGB)
3Mbps
Viewing Angle
H: 80 degree, V: 100 degree
Weight
Gross weight: 955g
Max 250m
Number of Camera Support
Up to 4 cameras
Power Requirement
Adapter : DC 6V ±10%, Battery : 3.7V Li-polymer
Image Sensor Type
1/5” Color CMOS Image Sensor
Loud Speaker Output
80dBA
Loud Speaker Noise level
45dBA
Power Consumption
480mA maximum Condition Charging + Speaker with voice at volume 5
Operating Frequency Range
System General
2400 MHz~2483.5 MHz
Transmitting Power
17dBm Max
Type of Spread Spectrum TX
FHSS
Monitor Sensitivity
Type of Modulation
Data Rate
Transmission range
Effective Pixel
White Balance
Lens
Viewing Angle (Diagonal)
IR LED Type/ Night Vision
Loud Speaker Output
Power Requirement
Power Consumption
VOX level detection
Operating Temperature Range
14 · Appendix
-88dBm
Wireless Camera
H: 640, V: 480
Auto
Wireless Monitor
Operating Temperature Range
0°C~+40°C
Operating Humidity Range
85% RH
Environment Rating
Indoor use only
Regulation Compliance
FCC/CE
DC 6V ±10%
RoHS Compliance
Yes for CE version only
High: 50dBA / Low: 60dBA
EFL=3.0mm, F=2.5
56 degree
8pcs IR LED – 940nm /5m
80dBA
480mA Condition Night vision mode and talk back.
Audio
Built in Microphone/ Speaker
Other Special Feature
Volume control, Pairing
0°C~+40°C
Battery Type
Li-on
Battery Capacity
1300mAh
Weight
186g
Troubleshooting
Problem
No picture from a
camera
Solution
1.
2.
3.
4.
5.
Check all connections to the camera. Make sure the adapter is plugged in.
Make sure that the cameras and monitor are both ON.
Make sure that the camera is in range of the monitor.
Make sure the camera and monitor are paired.
Adjust the monitor antenna to vertical position.
The picture is or has
become choppy
The picture may become choppy when experiencing a lower frame rate
(i.e. 10 frames per second vs. a higher 20 frames per second).
No sounds (even with
both units turned on)
1. Make sure that the power adapter is connected to the camera.
2. The battery on the monitor may be dead, be sure to charge it using the
adapter included.
3. The monitor may be out of range of the camera; be sure to check if the
Range LED in on continuously.
batteries will cause the supply current to become unstable and will affect the quality
nn `` Low
of the video/audio. Please charge the battery fully for use for superior video.
Appendix
This sound is normal feedback which occurs if the monitor and camera are too
close together. Move them further apart.
06
Your SimpleVIEW
is emitting an high
pitched noise/
feedback.
1. Try moving the camera closer to the monitor.
2. Remove obstructions between the monitor and camera.
3. Adjust the monitor antenna to vertical position.
English · 15
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery
return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this
product should not be disposed of with other household waste at the end of their working
life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries
are not properly disposed of, these substances can cause harm to human health or the
environment.
To protect natural resources and to promote material reuse, please separate batteries from
other types of waste and recycle them through your local, free battery return system.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection
systems)
This marking on the product, accessories or literature indicates that the product and
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life. To prevent possible harm
to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take these items
for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
50mm [2 inch]
TEMPLATE
This template is used to install
the camera on the wall.
Screw holes for
the Camera
installation
CAMERA FRONT
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : 1-877-349-3149
www.samsungsv.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey,
Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : n
Create Date                     : 2014:05:19 14:46:05+09:00
Modify Date                     : 2014:06:13 16:57:22+09:00
Has XFA                         : No
Language                        : ko-KR
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : n
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2014:06:13 16:57:22+09:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:ed975a96-eec2-474d-826b-502949ca8fad
Instance ID                     : uuid:1c46c294-f1b2-4fd1-bf23-7313657931b0
Page Count                      : 9

EXIF Metadata provided by EXIF.tools