Hanwha Techwin SNHP6412BN SMARTCAM User Manual
Hanwha Techwin Co., Ltd. SMARTCAM
User manual
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
Operational Description
The operational description shall fulfil the requirements of Rule Part 2.1033(b)(4). The rule
part requires, "A brief description of the circuit functions of the device along with a
statement describing how the device operates. This statement should contain a
description of the ground system and antenna, if any, used with the device".
The above requirement has been further interpreted by the FCC to mean that the
description shall:
a. be an operational or technical description of how the device operates, is modulated
and meets requirements;
b. describe the EUT completely. What is it (in plain English as well as technical terms)?
Give a clear, concise functional description of device operation.
c. always describe the signal, such as modulation type, pulse repetition rate, signal type
and information being sent. Describe all modulation types and all data rates.
Instructions & Warranty
The manufacturer is not responsible for any loss or radio/TV interference caused by
unauthorized modification of the product.
Such modification will void the warranty of the product as well as the user’s right of use.
WARNING
• The product must be assembled and installed by an adult.
• Before using, read all instructions on this manual thoroughly and follow operational
instructions, warnings on this manual and printed on the product.
• To avoid entangled power cord, do not place it around the baby bed or other infant
furniture. Keep this product and its power cord out of children’s reach.
Copyright
©2015 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks
mentioned in this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be
reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Samsung makes the best to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this document and the
subsequent results shall be entirely on the user’s own responsibility. Samsung reserves
the right to change the contents of this document without prior notice.
Samsung SmartCam
User Manual
• Especially, the power cord should be installed carefully while keeping it out of
children’s reach.
• Never use the product near bath tub, sink, washing machine and in wet basement to
avoid moisture.
• The product is designed for indoor use.
• The product is not designed for medical monitoring, and requires a grown-up’s
protective supervision on its use.
• To avoid overheating of the product, do not expose the product to direct sunlight; do
not install or use near a heat source such as heater, radiator, cooking devices (ex:
electric stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).
• Make sure to keep ventilated while using the product.
Avoid pillar or furniture that may block ventilation, when installing the product.
• Make sure to use the power adaptor provided. If used with unidentified adaptor, it
may damage the product. The power adaptor must be used with regular household
electric supply.
• Avoid sharp, pointed objects around the adaptor’s cable, not to damage the cable.
• Be warned and never hold the cable’s stripped part when connecting / disconnecting
the adaptor to/from the wall outlet.
• To avoid entangled cable lines, avoid using cable extension for adaptor’s power cord.
• The product’s servicing is allowed only to authorized Samsung's service personnel.
• When using the product for children’s care, be careful to keep the product out of
children’s reach.
• The product partially contains component which might cause respiration difficulty.
Accessories and small parts of the product should be stored keeping out of children’s
reach.
• The product is not designed to replace responsibility of human supervision on
children.
• The product is not equipped with device of immediate notification to adult with
accidental/sudden children‘s move; it requires periodic checks and human
supervision.
• This appliance and its antenna must not be collocated or operation in conjunction
with any other antenna or transmitter. A minimum separation distance of 20 cm must
be maintained between the antenna and the person for this appliance to satisfy the
RF exposure requirements.
• Please note that the content of a micro SD card used for other purposes may be
deleted when it is mounted in the camera.
Contents
GETTING STARTED
Features ……………………………………………………… 4
What’s Included ……………………………………………… 5
Part names and functions …………………………………… 6
INSTALLATION & NETWORK CONNECTION
Installation …………………………………………………… 8
Network Connection and Settings …………………………… 12
MONITORING
Registration …………………………………………………… 14
Live Video …………………………………………………… 19
Setup ………………………………………………………… 22
Event Alarm ………………………………………………… 29
Playback ……………………………………………………… 30
Information …………………………………………………… 30
APPENDIX
Specifications ………………………………………………… 32
Troubleshooting ……………………………………………… 36
4
· English
Features 4
What’s Included 5
Part names and functions 6
Power Supply 7
Connecting the Ferrite Core to the power supply
adaptor 7
Network connection 7
01
GETTING STARTED
• Easy to install
- Simply visit the home page (www.samsungsmartcam.com) and download and
install the program without a separate installer program.
• Remote monitoring
- Whenever and wherever if you are in the Internet enabled environment, remote
monitoring is ready for you.
- PC, laptop or smart phone can be used for monitoring.
• Real-time alarm
- When a motion and sound are detected, your smartphone will generate real time
alarms.
• Cloud Storage
- Users can automatically upload event photos to their Picasa accounts.
- Anytime anywhere you can enjoy the video and images stored in the cloud
storage.
• Saving in SD card
- When an event occurs, the user can save the video in their SD card.
• Two-way Audio
- With the built-in speakers and microphone, you can make Two-way
communications.
However, it is available only with the smart phone. (Not applicable to the PC or
laptop computer.)
• SNS (Social Networking Service) Alarm supported
- Provide event alerts through Picasa.
- Share your photos with your friends.
• IR LED
- At low illumination levels, you can use an IR LED for monitoring purposes.
Features
5
01
Getting Started
What’s Included
Check for components when opening the product package.
Camera & Bracket body Power Adaptor Network Cable Quick Start Guide
Warranty Card GPL Lisence Double Sided Tape Tapping screw
Plastic anchor Ferrite Core
n `Keep the packing container. You will need the serial number later to register the camera.
6
· English
Part names and functions
RESET
NETWORK
RESET
NETWORK
SAMSUNG SMART CAM
HANWHA TECHWIN CO., LTD. MADE IN CHINA
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
DC 5.0V 2.2A
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
Camera lens
Luminance Sensor
Detects light levels where the camera is placed.
Night vision mode changes according to detection
result. Audio out
Generates audio output to external devices.
Built-in IR LEDs for night vision
Power / Network status LED
Micro card insertion hole
Wi-Fi Direct button
Create a Wi-Fi connection for your camera and
smart phone.
Reset button
Resets the camera settings to the default.
Press and hold for about 10 seconds to reboot the
system.
Network port
Used for wireless connection.
Power connection terminal
Connect to the power adaptor.
Built-in Mic
Speakers
Generate audio output from your smart phone.
7
01
Getting Started
Power Supply
Plug-in the camera power adapter to the wall outlet and connect the camera as
shown.
n `Make sure to use the provided power adaptor. If you use an adaptor other than the
power supply adaptor provided in our package, the product may not operate properly.
`It will take about 1min for the camera to boot-up completely.
`When the boot-up is complete, the power LED color will change from red to blue.
Connecting the Ferrite Core to the power supply adaptor
Ferrite Core can stabilize the power supply.
1. Open the Ferrite Core included in the package.
2. As shown in the figure, place the ferrite core about 10 cm away from the
warning tag of your adaptor and roll it up to show the two lines of power
supply outside. Then close the ferrite core.
Network connection
Connect the provided network cable to the camera’s network terminal.
For further details on network configuration, refer to "Network Connection and
Settings". (Page 12)
LED status
LED indicator shows operational status with colors.
Refer to table below for detailed meaning of the LED indicator.
Color Status
Red Booting up
Red Blinking Booting completed / Establishing network connection
Blue Blinking Connecting to the network.
Blue Local connection established
Green Connection to server completed / Normal operation
Purple Updating firmware
RESET
NETWORK
RESET
NETWORK
SAMSUNG SMART CAM
HANWHA TECHWIN CO., LTD. MADE IN CHINA
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
DC 5.0V 2.2A
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
8
· English
Installation 8
Precautions 8
Wall Mounting Using Double-sided adhesive tape 9
Wall Mounting with Screws 11
Desktop mounting 12
Network Connection and Settings 12
Precautions 12
Connecting via network cable 13
Wi-Fi connection setting 13
02
INSTALLATION &
NETWORK CONNECTION
Precautions
1. Install the camera in a place where the Wi-Fi signal can be reached and
without interference.
2. Keep it away from humidity such as around the humidifier.
3. Keep it away from direct sunlight, strong light or dust; install it in a place with
clear view.
4. Do not install it in a place where there are a lot of obstacles.
5. Keep the lens clean at all times.
Wipe off the dust with a soft cloth.
Installation
9
02
Installation & Network Connection
Wall Mounting Using Double-sided adhesive tape
Separating the wall-mount bracket
1. While pulling the button in the back of the bracket, press the bottom of the
opposite side of the button to remove the bracket wall.
Assembling
1. Take out the wall fixing tape.
2. Remove the rectangular protective film from
the adhesive tape and attach it to the
bottom of the wall-mount bracket.
3. Hold the handle for the wall fixing tape, remove the release paper to attach
the tape.
n `The tape will lose adhesiveness if used once, do not re-use.
`Before attaching tape, clean dust / water / oil off the wall-mount bracket’s adhesive
spot for better result.
RESET
NETWORK
SAMSUNG SMART CAM
HANWHA TECHWIN CO., LTD. MADE IN CHINA
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
DC 5.0V 2.2A
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
10
· English
4. Firmly insert the bracket from the opposite side of the button until you hear a
clicking sound.
5. Connect the adaptor’s plug to the power terminal on the camera’s rear side.
n `When done, remove the protective film from the lens.
Adjusting the Angle
1. Adjust the camera’s shooting angle as
appropriate.
n `Do not put excessive force. Otherwise, it may
cause damage to the camera.
2. Open the cap in the area marked in the figure
and use a driver to turn the screw clockwise to
fasten and fix the recording angle.
3. If you turn the screw counterclockwise, it will be
loosened and you can adjust the recording
angle then.
RESET
NETWORK
RESET
NETWORK
SAMSUNG SMART CAM
HANWHA TECHWIN CO., LTD. MADE IN CHINA
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
DC 5.0V 2.2A
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
11
02
Installation & Network Connection
Wall Mounting with Screws
n `For more information about step of Separating the wall-mount bracket, refer to "Wall
Mounting Using Double-sided adhesive tape".
Assembling
1. Take out screws (M3xL20), and anchors (Φ5x25mm).
2. On a wooden wall, use screws to fix the
wall-mount bracket as shown in the figure.
Using a driver on the wall to attach it to,
fasten three screws in the three holes.
3.
If fixing on a concrete wall, use screws and anchors to fix wall-mount bracket
.
First, mark on the wall as shown in the figure below.
4. Use drill bit of 5mm diameter and drill on the
marked positions, drill to have 3 cm depth
holes. Clean the holes after drilling.
J `Be careful not to get injured while drilling.
5. Insert an anchor for each hole. Fully insert
anchors by hammering lightly the anchor
head with a hammer/rubber hammer.
6. Using a driver on the wall to attach it to,
fasten three screws in the three holes.
n `For further steps, refer to the instructions for
"Wall Mounting Using Double-sided
adhesive tape".
12
· English
Precautions
• The wireless network access may fail, depending on the communications
environment.
• For details about the network settings and password, contact your network
administrator or service provider.
• For a specific Internet service requiring user authentication, you may not access
the service. If this is the case, contact the service provider.
• Do not access the unauthorized network.
• The farther the distance from the Wireless Access Point, the longer time the
network connection may take.
• If you fail to access the selected wireless network, try a different Wireless
Access Point to make access.
• For more information about the router or the wireless connection, refer to the
documentation of the router or contact the router manufacturer.
• If the camera is connected to a multiple-Wireless Access Point network
environment, some video packets may be lost, depending on the network traffic
load.
• According to the network policy (blocking UDP) of the service provider, the video
transmission can be limited to 7 minutes.
For more details, refer to the descriptions on page 21, <Relay Mode>.
• In addition to the above two situations, you may encounter a network delay or
interruption due to the network conditions.
• Some hubs can have compatibility issues.
Network Connection and Settings
Desktop mounting
n `For more information about step of Separating the wall-mount bracket, refer to "Wall
Mounting Using Double-sided adhesive tape".
Assembling
1. Firmly insert the bracket from the opposite side of the button until you hear a
clicking sound.
2. Using the groove on the bracket wall, rotate the bracket in the desired
direction.
3. Connect the adaptor’s plug to the power terminal on the camera’s rear side.
RESET
NETWORK
RESET
NETWORK
SAMSUNG SMART CAM
HANWHA TECHWIN CO., LTD. MADE IN CHINA
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
DC 5.0V 2.2A
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
13
02
Installation & Network Connection
Connecting via network cable
If you do not have a Wireless Access Point, you must connect the camera using
LAN cable directly to your home router.
1. When you apply the power, the power status LED is lit red, and it will change
to red blinking when the booting is completed.
2. Connect the network cable to the camera and to the home router as shown
below.
3. The status LED will become steady blue once the camera is connected to
the router. (may take up to 30sec).
If the status LED (blue) is not lit, repeat steps 2 through the end and check it
again.
4. The status LED will became steady green once the camera is connected to
server.
n `It is recommended to set the router to DHCP(Dynamic Host Configuration Protocol)
server.
If you want to use static IP address, please refer to <Wired Network> on page 23.
`If the router’s UPnP is not set, then you might be connected in relay mode.
The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
Wi-Fi connection setting
If you want to connect a camera to Wi-Fi, first connect the network cable and try
to make a connection to the Wi-Fi network.
1. When you apply the power, the power status LED is lit red, and it will change
to red blinking when the booting is completed.
2. Use the network cable (LAN cable) to connect the LAN port of the unit to the
LAN port of the Wireless Access Point.
3. Register and select the camera according to guide of 03. Monitoring.
4. Set your wireless network environment using the guideline <Wireless
Network> on page 24.
n `If you want to connect your camera to Wi-Fi, you need a hub that supports wireless
networking.
`Using the camera's Wi-Fi Direct function, you can easily make a Wi-Fi connection from
your mobile phone.
`When the wireless network settings are completed, remove the LAN cable.
`If you fail to connect to the Internet service, contact the service provider for details.
SAMSUNG SMART CAM
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
DC 5.0V 2.2A
HANWHA TECHWIN CO., LTD. MADE IN CHINA
Internet Service
<Modem>
<Hub>
OR
SAMSUNG SMART CAM
MODEL : SNH-P6410BN
M/C : SNH-P6410BN/EX
Aug 2013 S/N : XXXXXXXXXXXXXXX
MAC ADDRESS : XX-XX-XX-XX-XX-XX
DC 5.0V 2.2A
HANWHA TECHWIN CO., LTD. MADE IN CHINA
Internet Service
<Modem>
<Wireless Access Point>
14
· English
Registration 14
Web browser requirements 14
Starting SmartCam 14
Live Video 19
Monitoring options 20
Setup 22
Basic Info 22
Network 23
Time 25
Alarm & Notification 26
Alarm Schedule 28
SD card 28
Event Alarm 29
Playback 30
Information 30
My Account 31
Support 31
03
MONITORING
Once you register the product with the site, you can monitor the camera video on
the PC or laptop computer.
Web browser requirements
Windows Mac
Windows 7 supported
- Internet Explorer 9 or higher
(The 64-bit is not supported.)
- Firefox
Mac OSX 10.7 Lion or higher is
supported
- Firefox
- Safari
Starting SmartCam
1. From your PC, launch your web browser.
2. Go to http://www.samsungsmartcam.com.
3. Select preferred language.
4. Click <Sign up> or <Starting SmartCam>.
Registration
15
03
Monitoring
❖Plug in installation
You need to install your plug in to automatically search for cameras connected to
the network and view the video in your camera.
n `If you login or click <Starting SmartCam> in a PC where the plug in is not installed,
the installation message window will pop up.
`When you install the plug in, the web browser will be terminated and you need to
launch it again.
1) Click <Download Plug-in>, run the setup file.
For Windows
2) Click <Next>.
3) Click <Install> to begin the installation.
4) Installation has completed.
16
· English
For Mac
2) Click <Continue>.
3) Click <Install>.
4) Enter MAC PC password and click <Install Software>.
5) Installation has completed.
17
03
Monitoring
6. According to the network connection and setting, click <Next> when the
camera LED turns into green.
7. Select the serial number of the camera to be added from the camera search
list.
If the camera is not found, enter the serial number manually.
8. Click <Next>.
n `Serial number can be found the label on the side of the packaging or on the rear of the
product.
`The computer and the camera has to be on the same network router to auto detect
the cameras.
5. Enter the requested information, and click <Sign Up>.
• ID : Using alphabetical characters and numbers, make a combination
using 8 to 14 letters.
• Password : To strengthen security, create a password with a combination
of special characters, numerals and English letters.
J `Length and other restrictions of password.
- A combination of English letters/numerals: 10 digits or more
- The password must not be identical to your ID.
- No simple repetitive pattern must be used.
e.g., 1212abab,azxsazxs
- You cannot use 4 or more consecutive letters.
e.g., 1234, abcd
- You cannot use 4 or more consecutive qwerty keyboard letters.
e.g., asdf, 7890
- You cannot use any letter 4 consecutive times.
e.g., !!!!, 1111, aaaa
• Confirm Password : Please enter the password again for confirmation.
• Name : Enter the user name.
• E-mail : Please make sure you enter correct email address as you will have
to use the email address to receive temporary ID/password when you lost
your user ID or password.
18
· English
9. Create <Camera Name> and <Camera password>.
10. Click <Next>.
n `The camera password is used to block the unauthorized access to your camera.
`Create camera password using alphanumeric characters between 1 to 8 without any
space.
11. After adding the camera, click <Yes> in the wireless network setup pop-up
window.
12. Select your Wireless Network from the list.
13. Enter the password of your Wireless Network and click <Next>.
n `If your Wireless Network is hidden, select <Other Wi-Fi Networks (not listed)>.
`Select <Display password> to display the password.
14. Click <OK>.
19
03
Monitoring
1.
Select a camera from the camera list at the upper left hand of the screen.
n `The gray icon indicates the camera is inactive so you cannot monitor it right now.
2. Enter the camera password and click <OK>.
n `Check on <Remember> to access your camera without entering the password next
time.
`If you want to change the Camera password, please refer to <Basic Info> on page
22.
3. Live video will be displayed on the screen.
Live Video
15. Unplug the network cable from the camera and the router.
16. Click <Finish> if the <Finish> button is activated.
17. Once the camera is successfully registered, you can check the camera in the
camera list.
20
· English
Monitoring options
Item Description
Default Camera Set the default camera to monitor in the camera list.
b
Delete Camera Delete the registered camera.
c
Cancel remembering
camera password Cancel remembering the camera password.
Night Vision
If Night Vision is set <ON>, it will automatically switch to black
and white mode in the dark condition and then the IR lamp will
automatically operate.
If Night Vision is set <OFF>, it does not switch to night vision mode
and it will operate in color mode.
Item Description
WDR A dark spot will be brighter and a bright spot will be darker to
compensate for the backlight.
Motion zone setting It detects motion within the range set by a user.
Flip/Mirror You can flip/mirror the video image.
Manual recording
A user can directly save videos in their SD card.
`30 minute long video is saved.
`If there is an ongoing event now or overwrite to SD card is not
checked, and there is storage space of 10% remaining, you
cannot perform manual recording.
Network Speed
Set the network speed (low/mid/high).
`
If the bandwidth provided by your internet service provider is smaller
than the recommended value, then the video might get fuzzy or
temporary disconnections or delays in the live video may be caused.
Capture Image Live video is saved as one image.
Sound
When enabled, you can hear what’s happening around the camera.
`Some internet service providers do not support audio outputs in
relay mode.
Full screen
The video is displayed on the full screen.
`The system supports Internet Explorer only.
`If you double-click the screen, the full screen mode is terminated.
m
Brightness You can adjust the brightness of the screen image.
m
n
b c
21
03
Monitoring
Item Description
n
Hide/unhide detailed
menu Click on the [ ] icon to unhide or hide detailed setting menu.
Audio
Adjust the volume of the built-in microphone and speaker of the
camera as appropriate.
If you set the mic setting to '0', you will not hear the live audio, and
it will not be recorded in your SD card. Note that the Two-way audio
transfer function is available only with the smart phone application.
Add a camera Click the [ ] icon to register an additional camera.
❖Network Speed
Profile Name Resolution Frame rate Recommended
bandwidth
Low Speed Network VGA 20 fps 0.7Mbps
Mid Speed Network HD(720P) 15 fps 1Mbps
High Speed Network Full HD(1080P) 30 fps 2.8Mbps
n `What is relay mode?
If the network condition is unstable, the camera cannot make a normal connection
(P2P), so it will set up a connection in relay mode. In this case, you will see the video
for the first seven minutes only.
`Relay mode is added feature where the video from the camera is transmitted to
Samsung server then retransmitted to the user's computer.
`If you have trouble connection to the camera, visit "http://www.samsungsmartcam.
com", go to support page, and refer to "Troubleshooting" on it.
`It is recommended to use one browser at one time.
`The Night Vision video produces a different visibility according to the distance between
camera and subject.
❖Motion Zone Setting
1) Click the < > icon.
2) Drag it to the screen to set the detection area.
3) Click on <OK>.
If you want to delete the set area, click on <Delete All>.
n `The <Motion Detection> function needs to be activated in order to use the motion
zone function.
`When the motion detection function is activated, any motion will be detected, even if
no motion zone is set.
`You can set up to 3 motion zones.
22
· English
Item Description
Serial number You can confirm the serial number.
b
Camera password
Click the <Modify>, you can change the Camera password.
Enter the current camera password, and type a new Camera password.
c
Camera Name Click the <Modify>, you can change the camera name.
Firmware Version You can check the current version and the latest version of your
camera S/W.
Status LED You can turn on/off the LED in your camera.
`
The LED will illuminate when the power supply is reconnected.
Flickerless
You can reduce the occurrence of screen shaking due to the frequency
mismatches with the neighboring lighting.
`
If you use the flickerless function outdoors (in a bright environment),
image saturation may occur.
Image encrypting
This encrypts the image transmitted.
`
The image encryption function may affect the image transmission
function.
n `If you change the camera password, you will be logged out and return to the camera
password input page.
`Keep the camera password in a safe place as it is used for viewing the live screen of
the camera or for changing the display settings.
Setup
Basic Info
b
c
23
03
Monitoring
❖Firmware update
If the currently used S/W is not of the latest version, update it.
If you are using the latest version, then the firmware will not be activated.
1) Click <Firmware>.
2) Click the < > icon to update the firmware.
3) When the firmware update is finished, the camera will reboot.
n `If you want to update the firmware, it is recommended to use a wired network
connection.
`If the power goes off during updates, it may not operate properly.
`The duration of the firmware update depends on the size of the firmware file and the
network connection speed.
`When you run Update Firmware, the color of your camera LED changes to purple.
J `Do not disconnect the camera from power or the Internet during a firmware update, as
this may damage the system.
Network
Item Description
Dynamic IP Address If you select <Dynamic IP Address>, the IP address will be obtained
automatically.
b
Static IP Address You must manually provide the information of: IP address, subnet
mask, gateway, DNS server address.
<Wired Network>
b
24
· English
n `If any of the manual settings is wrong, the network settings will not be applied.
`If you have both cable and wireless network connections simultaneously, the cable
network connection is prioritized.
`If you switch from the current wireless connection to the cable connection, the network
will switch to cable connection accordingly.
`For more information about the router or the wireless connection, refer to the
documentation of the router or contact the router manufacturer.
Item Description
Wireless On/
Wireless Off
You can select to activate or deactivate the wireless network
connection.
b
AP (Access Point) list You will see a list of APs (Access Point) available. Select a desired one
from the list of APs (Access Point).
c
AP (Access Point)
password
If you select a secured AP (Access Point), you must enter the
password before you can access the network.
For the password, contact your network administrator.
Hidden SSID If your SSID is hidden, select the type of security you have. Enter the
name of the SSID and the password.
n `If you select a non-secured AP (Access Point), you just can access the network without
providing a specific password.
`If you entered a wrong password, you cannot access the network whatsoever.
`When the wireless network settings are completed, remove the LAN cable. If you do
not remove the LAN cable, the wireless network will not be available.
<Wireless Network>
b
c
25
03
Monitoring
Time
Item Description
Time Confirm the camera's time.
b
Time Zone Select your region.
c
Display Time Select the time format displayed in time setting.
Automatic Time It sets camera's time automatically.
Daylight Saving Time Check this option if you live in a country or region where DST(Daylight
Saving Time) is applied.
Time to show Live screen displays the time.
n `The time will synchronize with the NTP(Network Time Protocol) server automatically.
For this, Internet connection is required.
`You need to set the timezone correctly to obtain the exact time setting.
`The time displayed without Internet connection may not be accurate.
c
b
26
· English
<Gmail> Notification
The event alarm is sent through Gmail.
1. Select the Google.
2. Enter your Gmail address and password.
3. Select <Use> of "Send alarms".
4. Enter your email address to receive the notification e-mail and click <Add>.
Now, the receiver full email address will be shown in the List Box. If you want
to register more than one email address, you can just repeat the same
procedure.
5. Click <Save>.
n `
If your Google email ID/password are saved, only check "Send alarms".
`
If the email address for the recipient entered is incorrect, event alerts will not be sent.
`
Even if you entered a correct google account ID, if the ID/password confirmation pop up
window appears, click on <Go to the google page.> and check the google account.
Alarm & Notification
Camera has ability to send event notifications when motion or audio is detected.
Item Description
Alarm notification
You can set motion or audio alerts. Sensitivity level can also be set.
The higher the sensitivity, the more accurate motion and audio events
can be detected.
`When an event occurs, if you want to send alerts to Picasa/Gmail,
first log into your google account.
n `In the following case, it may fail to derive the proper results for basic events and
motion detection.
- The object color or brightness is similar to the background.
-
Multiple movements continue occurring at random due to a scene change or other reasons.
- A fixed object continues moving in the same position.
- An object hides other objects behind.
- Two or more objects overlap or one object divides in multiple portions.
- A moving object comes close to the camera.
<Receiver
email address>
27
03
Monitoring
<Picasa> Notification
Automatically uploads a image to your private Picasa account.
1. Select the Google.
2. Enter your Gmail address and password.
3. Click <Save>.
4. Check <Use> of Picasa.
5. Click <Authentication requests.>
6. Sign in with your Google account.
7. Click <Access>.
8. Copy the code on the authority request page, then click <Apply>.
n `
If your Google email ID and password are saved, check the use of Picasa only.
`Refer to the policy of Picasa for the maximum number of uploaded images.
Push alarm Notification
The push alarm is provided through the web viewer and mobile app in which the
camera is registered.
•
If you activated Use, then image links uploaded into Picasa will be sent to the
friends listed in real time.
•
Push alert list shows the list of IDs of users who registered cameras.
When an alarm occurs, the web site will send push alerts to each smart phone.
28
· English
Alarm Schedule
When the user designates a desired day and time, the alarm works only at the
designated time.
Item Description
Only Scheduled Time Alarm function will only operate for the time/day designated by the
user.
b
Always Alarm function always operates.
c
Motion time settings
You can click and drag to set the motion time in hours.
Example) When you select 00, an event will occur and remain from
00 to 00:59
SD card
When an event occurs, it is saved in an SD card.
Item Description
Use the SD card If you set motion/audio, video will be automatically saved in your SD
card.
b
Continuous Recording
Saves the video without being interrupted by events that may occur.
c
Overwrite
If the SD card capacity is insufficient, it will start overwriting the oldest
data.
`When there is storage capacity of 10% remaining, the top
notification window will show an alarm.
SD Card Status Check the remaining capacity of your SD card and delete all the data.
c
b
b
c
29
03
Monitoring
n `Turn off the camera power or set it to <Off> before removing the micro SD card. If you
fail to do this, the data in the micro SD camera may be damaged.
`Please note that the content of a micro SD card used for other purposes may be
deleted when it is mounted in the camera.
`The following micro SD cards are recommended for this camera.
Manufacturer : Sandisk, Transcend
Class 6 or higher, MLC type
`Micro SD card of max 32GB is supported and a FAT32 file system is supported.
`It is recommended to use the micro SD card after formatting it. Regularly formatting
the memory card will help extend its life.
Event Alarm
You can check the event alarm that occurred.
Item Description
Delete by dates Delete all the event alarms on the date.
b
Image displays Select and click on the desired event. You can view an image.
`Image is displayed only if Picasa is activated.
c
Delete All Delete all the event alarms for thirty days.
Display Events Displays the number of events occurred in the 30 day list.
Arrange by types Arrange the event list by event types.
n `
Even if you delete an event in the event notification page, the Picasa event will not be
deleted.
b
c
30
· English
InformationPlayback
You can play the video recorded in your SD card.
Item Description
Type Set the event type to search for during the search period.
b
Date Set the search date for the data saved in your SD card.
c
Play/pause Play and pause video.
Search Perform event searches.
Refresh Renew the events displayed in timeline.
Timeline Use the timeline to play the video in the desired time.
b
c
31
03
Monitoring
My Account
n `
If you want to change the member information, click on <Account>. Select the item
(password, or email address) and enter your information.
Support
You can download the Samsung SmartCam mobile app and user guide.
32
· English
Specifications 32
Specifications 32
Product Appearance 35
Troubleshooting 36
04
APPENDIX
Item Description
Video
Imaging Device 1/2.8" 2M CMOS (1080P Support), SONY, FHD
Effective Pixels 1,944(H) x 1,224(V)
Scanning System Progressive
Synchronization Internal
Low Light Performance 0.3Lux(Color), 0Lux(Black/White)
Lens
Focal Length (Zoom Ratio) 2.8mm
Angular Field of View (D/V/H) 128°/ 62°/ 111°
Min. Object Distance 400mm
Focus Cotrol Fixed
Lens Type Barrel type
Specifi cations
Specifications
33
04
Appendix
Item Description
Video Analytics
WDR Support (2M@15fps)
Motion Detection Support (Motion zone : 3ea)
Audio Detection Support
Operational
Install Easy Set-up
On Screen Display (Web Browser) Support
Day & Night True D/N Filter
Night vision IR-LED, 5M
OS Linux
White Balance Auto
Digital Zoom (viewer support) 4X (Mobile), 10X (Web)
Digital Pan/Tilt (viewer support) Support
Flip / Mirror Support
Booting time Max 1 minutes
Network
Ethernet RJ-45 (10/100BASE-T)
Wireless Wi-Fi 802.11 a/b/g/n (Dual-band)
WPS (Wi-Fi Protected Setup) Not Support
Wi-Fi Direct Support (mobile)
Video Compression Format H.264, MJPEG
Item Description
Resolution 1920x1080, 1280x720, 640x360
Max. Framerate H.264, 1920x1080 30FPS
Video Quality Adjustment H.264: Compression Level
MJPEG : Quality Level Control
Bitrate Control Method H.264 : VBR with CAP
MJPEG : VBR with CAP
Streaming Capability Multiple Streaming (Up to 4 Profiles)
Audio I/O Support(Audio output, Mono jack)
Audio Compression Format G.711, G.726
Audio Communication Two-way Audio (Built-in Microphone, Speaker)
Half Duplex with AEC
Protocol TCP/IP, DHCP, SMTP, DNS, RTSP, RTCP, RTP, HTTP, TCP, UDP,
STUN, TURN, XMPP, SIP, uPNP, SNTP, IPv4, ICMP, Bonjour
Security SSL (AES 256bit)
Streaming Method Unicast
Max. User Access 5 users at Unicast Mode
Memory Slot microSDXC (FAT32)
PC OS Support(Web viewer) Windows7, Window8(Only Desktop UI) or higher
Mac OSX 10.7 or higher
Mobile OS support(Mobile viewer) Android OS : 2.3.3/4.0/4.1/4.2/4.3
iOS : 5.0/6.0/6.1/7.0
34
· English
Item Description
Fun
Audio recording User selected music record play
- 3 Lullaby songs saved - User voice recording feature support
Environmental
Operating Temperature / Humidity 0°C ~ +40°C (+32°F ~ +104°F)/20% ~ 80% RH
Ingress Protection Not Support
Electrical
Input Voltage / Current 5V DC / 2.2A
Power Consumption Max. 11W
Indication 1 LED (Power, Status, Link)
Mechanical
Color / Material White/Silver
Dimension (WxHxD) 83.9 x 118.9 x 79.3 (bracket), 44.5/36.5 (body)
Weight 293g
35
04
Appendix
Product Appearance
36
· English
If you encounter a problem with your system, see the table below to solve the problem
as quickly and easily as possible. Please follow the instruction below:
Troubleshooting
Problem Action
I forgot my user ID/
password.
- Move to "Log-in page Forgot your ID/Password?", and enter the
registered e-mail address to which we will send you the user ID and/or a
new password.
It can be spammed out depending on the policy of the email server.
After logged in, it is advisable to change the temporary password provided.
Camera is not
connected to the
wireless hub.
- If the camera's wireless internet indication LED goes off too often, then it
means that the camera installation location is not optimal for the wireless
internet environment, so in this case, locate the camera close to the wireless
hub and try to connect again.
- Check the password for the wireless hub and try again.
After logged in,
I failed to register the
camera.
- Check that the serial number entered matches the label on the back of the
camera.
- Enter the correct password for the camera registered again and try to
register the camera again.
- Check the camera LED to see if it is green. If not, then check the network
connection.
- If you are still unable to register the camera after this, then reset the camera
to factory settings and begin again.
(If you want to reset to factory settings, press and hold the initialize button
on the back for 10 sec. Once initialized to factory settings, the camera will
be restarted.)
Problem Action
The capture images in
the camera will not be
uploaded to Picasa.
- Move to Setup Alarm & Notification and adjust the sensitivity as
necessary.
- From the Alarm & Notification setup, configure the Picasa notification
settings. (See page 27 of the manual)
- Picasa has different service policies according to the country. The policy for
your country may prohibit uploading to Picasa. Please first check the Picasa
policy for your country.
- According to the Picasa policy, it may limit the uploading size. Check the
allowable free space of your Picasa account, and if insufficient, delete the
exiting images.
The video from the
camera is temporarily
lost.
- The video from the camera can be delayed according to a network delay.
Please check if the camera is installed in a place of proper wireless Internet
communications.
No sound is output
from the video.
- Click the Voice icon in the video playback page, or check if the voice is
turned On in your smart phone app.
- Some internet service providers do not support audio outputs in relay mode.
I forgot my Camera
password.
- You must create a new camera password.
- Press the initialization button on the back of the product for more than 10
seconds to reset to factory settings.
- After factory initialization, when you access the camera, you can reset the
password for the camera.
I want to change my
password and/or
email address.
- After logging in, click on the <Account>. Select the item (password, or
email address) and enter your information.
Camera will be
connected in a relay
mode.
- Check the UPnP setting of the router.
- Using a network upload speed of 500Kbps or higher is recommended.
- Depending on the policy of your service provider, you can access in relay
mode.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking on the product, accessories or literature indicates that the product and
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed
of with other household waste at the end of their working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
Samsung cares for the environment at all product manufacturing stages, and is taking
measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
SALES NETWORK
HEAD OFFICE
6, Pangyo-ro 319beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82-70-7147-8753, 8764 Fax : +82-31-8018-3740
www.samsungsecurity.com
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Customer support : +1-877-349-3149
www.samsungsv.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey,
Surrey, UNITED KINGDOM KT16 OPS
Customer support : 00800-8010-8022
www.samsungsecurehome.eu
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1
through 11.
If the device is going to be operated in the 5.15 - 5.25 frequency range, then it is restricted to
indoor environment only. This device meets all other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
Industry Canada Statement
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,
y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Industry Canada Caution
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential
for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated
as primary users (i.e. priority users) of the bands 5250- 5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une
utilisation à l’intérieur a n de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les
utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la
priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer
du brouillage et/ou des dommages aux dispositifs LAN-EL.
Industry Canada Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the
radiator & your body.
Déclaration d’exposition aux radiations
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non con trôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.