Hanwha Techwin SSA-S2000V Standalone RFID Access Controller User Manual Appendix6 SSA S200

Samsung Techwin Co Ltd Standalone RFID Access Controller Appendix6 SSA S200

User manual

Standalone RFID Access ControllerUser Manual SSA-S2000V
Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved.Trademarkis the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.RestrictionSamsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this docu-ment shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.DisclaimerSamsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.WarrantyIf the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded: If the system behaves abnormally because you run a program irrelevant to the system operation. Deteriorated performance or natural worn-out in process of time Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)•••Standalone RFID Access ControllerUser Manual
English _ 3safety informationCAUTIONRISK OF ELECTRIC SHOCK.DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.WARNINGTo reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.WARNINGBe sure to use only the standard adapter that is specifi ed in the specifi cation sheet.Using any other adapter could cause fi re, electrical shock, or damage to the product.Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to the product.Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.When installing the controller, fasten it securely and fi rmly. The fall of controller may cause personal injury.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the controller. Doing so may cause personal injury due to fi re, electric shock, or falling objects.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.). When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.CAUTIONDo not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.Do not install in a location subject to high temperature (over 50°C), low temperature (below -30°C), or high humidity. Doing so may cause fi re or electric shock.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage to the product.Keep out of direct sunlight and heat radiation sources. It may cause fi re.Install it in a place with good ventilation.Avoid aiming the controller directly towards extremely bright objects such as sun.Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.The Mains plug is used as a disconnect device and shall stay readily operable at any time.•1.2.3.4.5.6.7.8.9.10.1.2.3.4.5.6.7.8.9.SAFETY INFORMATION
FCC StatementCaution : Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:This device may not cause harmful interference, andThis device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.1)2)Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specifi ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.1.2.3.4.5.6.7.8.9.10.11.12.13.14.IMPORTANT SAFETY INSTRUCTIONSsafety information4_ safety information
English _ 5CONTENTScontentsPRODUCT INTRODUCTION77 Features8 What’s included9 At a Glance10 Cable Color SchemeINSTALLATION AND EXTERNAL CONNECTION1111 Cable Selection12 Bypass Diode Connection12 I/O Connection14 External Reader ConnectionINITIALIZATION1515 Basic Operations16 Initialization16 Forced Initialization with External LineREADER MODE SETUP1717 Reader Mode Setup (RF ONLY)18 Reader Mode Setup (RF + P/W)18 Reader Mode Setup (PIN ONLY)19 Reader Mode Setup (RF/PIN Combination Mode)19 Enabling Keypad Input for the Card NumberUSER MANAGEMENT2020 To register cards in RF ONLY mode20 RegIsterIng cards In a combInatIon of RF and P/W modes21 To regIster cards In PIN mode21 RegIsterIng cards In RF card / PIN combInatIon mode22 To delete a regIstered card or PIN numberBASIC SETUP2323 Duress Alarm23 To specify the retry count for an unregistered ID24 To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit24 To specify the delayed start time in Secure mode25 To specify the operation time of the Door Contact Sensor25 To specify the limited time for the keypad input26 To specify the alarm output port for the dismantled device26 To open or close the entry door27 To set or release the QUICK mode27 To set or release the Toggle mode for the door relay
6_ contentsADVANCED SETTING3333 To specify the TTL output operation mode33 To set the chime bell function34 To specify the chime bell operation time34 To specify the input mode for AUX 135 To specify the input mode for AUX 235 To specify the input mode for AUX 336 To specify the input mode for the Exit Button36 To specify the input mode for the Door Contact SensorADDITIONAL FEATURES3737 Mute37 To specify the use of the tamper alarm38 To check the output specifi ed for a registered card user38 To check the output specifi ed for an unregistered card user 39 To check the output specifi ed for the Door Contact Sensor alarm 39 To check the output specifi ed for AUX 1 40 To check the output specifi ed for AUX 240 To check the output specifi ed for AUX 3I/O TIME SETUP2828 To specify the output time if the card is authenticated29 To specify the output time if the card is not authenticated29 To specify the Duress TTL output30 To specify the alarm output for an input error of the Door contact Sensor30 To specify the alarm operation time for AUX 131 To specify the alarm operation time for AUX 231 To specify the alarm operation time for AUX 332 To activate or deactivate the door relay by the Door Contact SensorOTHER INFORMATION4141 InItIal Values42 FunctIon codesTROUBLESHOOTING4444 TroubleshootingPRODUCT SPECIFICATIONS4949 product specifi cationscontents
English _ 7PRODUCT INTRODUCTIONFEATURESThis controller is best designed for a single entry door control (single door access control).This product can save up to 512 cards including the master card, with which you can make an effective management (such as adding, deleting or changing the settings) of the cards. Its epoxy adhesion and aluminium case guarantees shock-resistance and stable operation in a challenging environment.This product features 5 external ports that can be connected to the Exit button, Door Contact Sensor, Motion Sensor, and Fire Sensor. It also has 2 relay outputs that can control the door lock and alarm relay. The dual tamper switch triggers an alert if the product is forcibly disassembled.You can use the keypad to confi gure all settings as necessary. This product is designed for a standalone system.Single Door Access ControlYou can use the RF card (SSA-C100,SSA-C110,SSA-C120) to control a single door.User RegistrationYou can register a total of 512 cards including the Master Card.Keypad RegistrationSSA-S2000V is equipped with the built-in keypad that you can use to register, delete cards or confi gure various settings independently.Buzzer On/OffWith the help of various buzzer tones, you can check the operation status and the current settings and results of the product.External I/O PinsSSA-S2000V has 5 input ports and 4 output ports installed (2 relay and 2 TTL outputs).The input ports can receive signals from the Exit button and the Door Contact sensor, while the two relays can be connected to the door lock and the alarm device. One of the TTL output ports can function as a chime bell in connection with the door bell.Duress AlarmThis is used in a situation where you should open the door inevitably by a robber insisting to do so. Entering the two-digit duress alarm password with pressing the button and recognizing the registered card (or card number) can open the door normally, while you can set to produce the TTL signal notifying the door is forcibly opened.Limited Access Tries for an Unregistered CardYou can specify the limit of times to try accessing the door, and the suspended operation time of the keypad for an improper access.product introduction
8_ product introductionproduct introductionWHAT’S INCLUDEDCheck if the following items are included in the product package.SSA-S2000VMain Unit3.5 x 40mm Screws (x4)3.5 x 25mm Screws (x4)6 x 30mm Plastic Anchors (x4)CD ManualtGjQuick Guide Diodes (x2)(UF4004, 1N4001~4007) Master Card (x1)3mm Hex Wrench (x1)
English _ 9PRODUCT INTRODUCTIONAT A GLANCEFront/RearSystem Status LEDIndicates the operation status of the system.KeypadUse this to confi gure or release settings as appropriate, or enter a card number.3TAMPER SWITCH A tamper switch to detect falling from the wall.417-PIN Connector Used to connect to the power source or I/O cable.5Buzzer Piezo buzzer.6Fixing Hole Fixing hole for wall-mounting.SSA-S2000V3456
10_ product introductionproduct introductionCABLE COLOR SCHEMEItem Cable Color Signal Line DescriptionPowerRed DC +12V Power (+12V)Black GND(-) Earth-grounding for powerOutputBlue with white stripes NC(RL1) Door Relay NC TerminalGray with red stripes COM(RL1) Door Control Relay (COM) PortWhite with red stripes NO(RL1) Door Relay NO portPurple with white stripes NC(RL2) Alarm Relay (NC) PortWhite COM(RL2) Alarm Relay (COM) PortPurple NO(RL2) Alarm Relay (NO) PortOrange with white stripes TTL TTL Output PortBrown with white stripes CHI Chime Bell OutputInputOrange EXITExit button connection portYellow with red stripes CONTACT Door Contact Sensor Connection PortGreen AUX IN 1 Aux Input #1Green with white stripes AUX IN 2 Aux Input #2Green with red stripes AUX IN 3 Aux Input #3Pink DATA_0 Wiegand Data 0 Input PortSky blue DATA_1 Wiegand Data 1 Input Port
English _ 11INSTALLATION AND EXTERNAL CONNECTIONCABLE SELECTIONItemCable TypeCable Type1Power (DC12V)DC Power  This ProductBelden #9409, 18 AWG 2 Conductor, Unshielded Belden #9409, 18 AWG 2 Conductor, Unshielded 2Reader (power and data)External Reader  This ProductBelden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded 3Door Contact Sensor Exit Button Sensor Input Input  This ProductBelden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded 4Door Lock,Alarm DeviceLock (Alarm)  This ProductBelden #9409, 18 AWG 2 Conductor, Unshielded Belden #9409, 18 AWG 2 Conductor, Unshielded The cables should be thick enough to allow the maximum current consumed by the reader.JSSA-S2000V  DC12VPower SupplyRF Reader Lock/AlarmSensor Inputinstallation and external connection
12_ installation and external connectioninstallation and external connectionBYPASS DIODE CONNECTIONIf you connected an inductor (door locks or alarm device) to the output relay, there should occur a voltage surge while the inductor is turning on and off. If you do not connect a reverse diode to the relay, the surge voltage will cause damage to the electric circuit of the controller. To reduce this surge, it is recommended to connect a reverse diode between the devices.I/O CONNECTIONInput ConnectionConnect the DC 12V(+) of the power supply unit to the red line.Connect the GND(-) of the power supply unit to the black line.- Exit Button Connection Connect one line of the Exit button to the orange line.Connect the other line of the Exit button to GND.- Door Contact Sensor ConnectionConnect one line of the door contact sensor to the yellow with red stripes.Connect the other line of the door contact sensor to GND.- Auxiliary Input Device Connection (AUX 1 (green), AUX 2 (green with white stripes), AUX 3 (green with red stripes)Connect one line of the external input device to AUX 1, AUX 2, or AUX 3.Connect the other line of the external input device to GND(-).1.2.1.2.1.2.1.2.DC+DC-SSA-S2000VSSA-S2000VPUSHDoor Contact Sensor: Green with red stripes, GNDExit Button: Orange line, GNDLock/AlarmCathode Anode1N4004 ~ 1N4007 or equiv.DC + 12VPower SupplyBlack-Red+Door Contact SensorExit Button
English _ 13INSTALLATION AND EXTERNAL CONNECTIONOutput Connection- Door open (POWER FAIL SAFE) when the power is disconnected from the door lock (Door Relay)Connect the relay COM line (gray with red stripes for locking the door) to DC +12V.Connect the relay NC line (blue with white stripes for locking the door) to the plus(+) line of the door lock.Connect the minus (-) line of the door lock to GND (-).- Door close (POWER FAIL SECURE) when the power is disconnected from the door lock (Door Relay)Connect the relay COM line (gray with red stripes for locking the door) to DC +12V.Connect the relay NO line (white with red stripes for locking the door) to the plus (+) line of the door lock.Connect the minus (-) line of the door lock to GND (-).- Alarm Connection (Alarm Relay)Connect the relay COM (white for the alarm device) to DC +12V.Connect the relay NO line (purple for the alarm device) to the plus (+) line of the alarm device.Connect the minus (-) line of the alarm device to GND (-).- Chime Bell Connection (the chime bell operated by TTL-level signal must be installed in advance.)Connect the chime bell line (brown with white stripes) of the controller to DC +5V.Connect the GND line of the power supply unit to GND (-) of the chime bell.Press to a0ctivate EthNeT chime bell.1.2.3.1.2.3.1.2.3.1.2.3.EXITSSA-S2000VDOORLOCKEXITCONTACTAUX IN#1CHIME+12VGNDGNDALARMRELAYCOMDOORRELAYCOMDOORRELAYNOALARMRELAYNOSIRENGND+12VDC 12VPOWERSUPPLYPIR SENSORCHIME BELLEXITBUTTONDOORCONTACTCathode Anode1N4004~1N4007 or equiv.
14_ installation and external connectioninstallation and external connectionEXTERNAL READER CONNECTION- Proximity Reader ConnectionConnect the DC 12V(+) of the power supply unit to the plus (+) line of the reader.Connect the GND(-) line of the power supply unit to the minus (-) line of the reader.Connect the Wiegand data input line 0 of the proximity reader to the purple line.Connect the Wiegand data input line 1 of the proximity reader to the sky blue line.For a list of compliant readers (external readers), see the followings:- Standard 26bit Wiegand format proximity reader1.2.3.4.•SSA-S2000V(+)(-)Wiegand DATA0(Pink)Wiegand DATA0(Sky blue)Black-Red+GNDDC+12V
English _ 15INITIALIZATIONinitializationBASIC OPERATIONSInitial StatusWhile the product is working normally, the orange LED indicator blinks every one second.Predefi ned Operation for a Registered CardWhen reading a registered card, it opens the door with the melody.Exit Button OperationIf you press the Exit button, the door will be opened.Predefi ned Operation for an Unregistered CardWhen reading an unregistered card, it produces an alarm with the melody for two seconds. You can specify the use of the alarm and change the operation time.Secure Mode OperationThe person who exits the last can set the secure mode using the keypad.Set Secure mode: Press the button twice and press .Release secure mode: Present and authenticate a registered card or the Master Card to the reader. You can use the keypad to specify the delayed start time for the Secure mode. (Refer to the delayed start time in Secure mode on page 24.)For effective security purposes, you can set to activate the sensors (via auxiliary input ports) only in Secure mode.Duress AlarmIf you are forced to open the door under a robber’s control, enter the Duress password and press with the number of your registered card (or PIN). (See page 23.)How to use the chime bellWhen you have connected and set the chime bell, press to ring the chime bell. (See page 33.)MEXITSSA-S2000VtGj
16_ initializationinitializationINITIALIZATIONIf you have the Master Card registered, you can use it to initialize the device.Present the Master Card to the device.Press the button twice and press .The system will restore the factory default settings with all LED indicators blinking.Initializing the system will lose all data.If the product works abnormally, use initialization to restore the default settings. FORCED INITIALIZATION WITH EXTERNAL LINETurn off the product, shortcircuit between the green line and the orange line with white stripes, and turn it back on.When the initialization is completed, 3 LED indicators are blinking with a beep.Restore the connection of the two lines back to their original state.1.2.3.M1.2.3.SSA-S2000VtGjSSA-S2000VSSA-S2000V12VGNDGreenOrange with white stripes Connect(Short-circuit)
English _ 17READER MODE SETUP- You can specify the operation mode for the device.- Once a mode is specifi ed, it will not switch until you perform the initialization.- You must keep the Master Card in safe for later use as it is required for your change to the device settings.- If progression is halted for more than one minute during any of the following processes, the operation mode of the reader will return to the previous state.READER MODE SETUP (RF ONLY)No Master Card or Master PIN is ever registered.If you remember the Master Card or the Master PIN was registered, initialize the product and try again.When you turn on the product, all of the 3 LED indicators will fl ash with a beep.No flashing of the 3 indicators denotes that the reader mode is already specified.Press Button and Button in sequence and press .When the mode is specifi ed, only the green LED indicator fl ashes.Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.Present cards to register with the device one after another, and the device will register them with a beep. If you don’t want to register the cards right now, simply jump to Step 5 above without through Step 4 above.Present the registered Master Card to the product once again.The device enters Standby mode with only the orange LED indicator flashing.1.•2.3.4.5.6.reader mode setupSSA-S2000VSSA-S2000V SSA-S2000V SSA-S2000VSSA-S2000VÎÎÎtGjtGj
18_ reader mode setupreader mode setupREADER MODE SETUP (RF + P/W)No Master Card or Master PIN is ever registered.If you remember the Master Card or the Master PIN was registered, initialize the product and try again.When you turn on the product, all of the 3 LED indicators will fl ash with a beep.No flashing of the 3 indicators denotes that the reader mode is already specified.Press Button and Button in sequence and press .Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.Present a card to the device, enter the 4-6 digit password and press . If you don’t want to register the cards right now, simply jump to Step 5 above without through Step 4 above.Present the registered Master Card to the product once again.The device enters Standby mode with only the orange LED indicator flashing.READER MODE SETUP (PIN ONLY)No Master Card or Master PIN is ever registered.If you remember the Master Card or the Master PIN was registered, initialize the product and try again.When you turn on the product, all of the 3 LED indicators will fl ash with a beep.No flashing of the 3 indicators denotes that the reader mode is already specified.Press Button and Button in sequence and press .When the mode is specifi ed, only the green LED indicator fl ashes.Enter the 4-6 digit Master PIN number and press .When the Master PIN is registered, only the red LED indicator flashes.Enter a PIN number to register (4-6 digits) and press .Repeat the step above if you want to register PIN numbers with the device in sequence.If you don’t want to register the PIN number right now, simply jump to Step 5 above without through Step 4 above.Enter the 4-6 digit Master PIN number again and press .The device enters Standby mode with only the orange LED indicator flashing.1.•2.3.4.5.6.1.•2.3.4.5.6.SSA-S2000VSSA-S2000VSSA-S2000V SSA-S2000V SSA-S2000V SSA-S2000VÎÎÎtGjtGj
English _ 19READER MODE SETUPREADER MODE SETUP (RF/PIN COMBINATION MODE)No Master Card or Master PIN is ever registered.If you remember the Master Card or the Master PIN was registered, initialize the product and try again.When you turn on the product, all of the 3 LED indicators will fl ash with a beep.No flashing of the 3 indicators denotes that the reader mode is already specified.Press Button and Button in sequence and press .Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.Present cards or PIN numbers (4-6 digits) to register with the device one after another, and the device will register them with a beep. If you don’t want to register the cards right now, simply jump to Step 5 above without through Step 4 above.Present the registered Master Card to the product once again.The device enters Standby mode with only the orange LED indicator flashing.ENABLING KEYPAD INPUT FOR THE CARD NUMBEREnsure that you must have registered the Master Card.Present the Master Card to the device. Press Button and Button in sequence and press .Repeat Step 1 above to release the specified mode, press Button and Button in sequence, and press .You can set the device to allow you to control the door by entering the 8 digit card number using the keypad.The default is “Keypad Input Disabled”.1.•2.3.4.5.6.1.2.•MSSA-S2000VSSA-S2000V SSA-S2000V SSA-S2000V SSA-S2000VÎÎtGjtGjorSSA-S2000VtGjSSA-S2000V
20_ user managementuser managementTO REGISTER CARDS IN RF ONLY MODEEnsure that you must have registered the Master Card and the device is specifi ed in RF ONLY mode.Present the Master Card to the device. When the mode is specifi ed, only the green LED indicator fl ashes.Press Button and Button in sequence and press .When the device enters Standby, only the red LED indicator fl ashes.Present a card to the device, it will be registered with a beep. Repeat this step if you want to register multiple cards.Present the Master card to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode.REGISTERING CARDS IN A COMBINATION OF RF AND P/W MODESEnsure that you must have registered the Master Card and the device is specifi ed in RF + P/W mode.Present the Master Card to the device. When the mode is specifi ed, only the green LED indicator fl ashes.Press Button and Button in sequence and press .When the device enters Standby, only the red LED indicator fl ashes.Present a card to the device, enter the 4-6 digit password and press . Repeat this step if you want to register multiple cards.Present the Master card to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode.1.2.3.4.1.2.3.4.SSA-S2000V SSA-S2000V SSA-S2000V SSA-S2000VÎÎÎtGjSSA-S2000VtGjSSA-S2000V SSA-S2000V SSA-S2000VÎÎtGjSSA-S2000VtGj
English _ 21USER MANAGEMENTTO REGISTER CARDS IN PIN MODEEnsure that you must have registered the Master Card and the device is specifi ed in PIN mode.Enter the Master PIN number and press .When the mode is specifi ed, only the green LED indicator fl ashes.Press Button and Button in sequence and press .When the mode is specifi ed, only the green LED indicator fl ashes.If you enter a user number (4-6 digits) to register and press , the PIN number will be registered with a beep. Repeat this step if you want to register multiple PIN numbers.Present the Master PIN number to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode. REGISTERING CARDS IN RF CARD / PIN COMBINATION MODEEnsure that you must have registered the Master Card and the device is specifi ed in RF Card / PIN combination mode.Present the Master Card to the device. When the mode is specifi ed, only the green LED indicator fl ashes.Press Button and Button in sequence and press .When the device enters Standby, only the red LED indicator fl ashes.Present cards or PIN numbers (4-6 digits) to register with the device one after another, and the device will register them with a beep. Repeat this step if you want to register multiple cards or PIN numbers.Present the Master PIN number to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode.The door may be accessed in two ways: using the card or the PIN number.1.2.3.4.1.2.3.4.MSSA-S2000VtGjSSA-S2000V SSA-S2000V SSA-S2000V SSA-S2000VÎÎtGjorSSA-S2000V<Master PIN>SSA-S2000V SSA-S2000V SSA-S2000VÎÎ<Master PIN><User Number> <User Number>
22_ user managementuser managementTO DELETE A REGISTERED CARD OR PIN NUMBEREnsure that you must have registered the Master Card or the Master PIN number and the device is specifi ed in a certain mode. This is applicable in all modes.Enter the Master Card or Master PIN. When the mode is specifi ed, only the green LED indicator fl ashes.Press Button and Button in sequence and press .When the device enters Standby, only the red LED indicator fl ashes.Present a card or PIN number to delete.Repeat this step if you want to register multiple cards or PIN numbers.Present the Master card to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode.1.2.3.4.SSA-S2000VtGjSSA-S2000V SSA-S2000V SSA-S2000V SSA-S2000VÎÎtGjor
English _ 23BASIC SETUPbasic setupDURESS ALARMIf you are forced to open the door under the control of a criminal such as a robber, enter the predefi ned password with the number of your registered card (or PIN), which outputs the emergency TTL signal.Present the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit Duress code and press .The default code is set to “00”. However, the number “77” can not be used because it is set for the Secure mode.TO SPECIFY THE RETRY COUNT FOR AN UNREGISTERED IDYou can specify the retry count for authentication with an unregistered card or PIN.If the retry count exceeds the set limit, the keypad input will be suspended for the next one minute. (You can specify the keypad input suspension time in “To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit” on page 24.)Present the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit retry count and press .You can specify a number from 00 to 99.The retry count for an unregistered ID is defaulted to “05”.1.2.3.•1.2.3.••SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
24_ basic setupbasic setupSSA-S2000VtGjSSA-S2000VTO SPECIFY THE KEYPAD INPUT SUSPENSION TIME IF THE RETRY COUNT WITH AN UNREGISTERED ID EXCEEDS THE LIMITPresent the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit keypad input suspension time (unit: minute) and press . The default is set to “01”.You can specify a time from 01 to 99 minutes.You can specify the time of the keypad input suspension (followed by an alarm) if an unregistered user keeps trying to open the door for certain times (the code number is set to “82”.TO SPECIFY THE DELAYED START TIME IN SECURE MODEPresent the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit delayed start time (unit: minute) and press . The default is set to “00”.See the table below for your reference.Secure Mode When the last person set the Secure mode before exiting the offi ce, the external sensors will get activated since then.Delayed StartIf the external sensors get activated right after you set the Secure mode, your motion will be detected before you can get out of the secure area, which will trigger the alarm. Thus, it is recommended to set the Secure mode to get activated after a certain time.Enter the delayed start time by the minute; the sensor operation in Secure mode must have been specifi ed in advance. (Refer to “Alarm Operation Time for Auxiliary Input” on pages 30-31)1.2.3.•M1.2.3.•MSSA-S2000VtGjSSA-S2000V
English _ 25BASIC SETUPTO SPECIFY THE OPERATION TIME OF THE DOOR CONTACT SENSORThe Door Contact sensor detects the opening of the door.If the door is forcibly opened by an unregistered user, the Door Contact Sensor will perform the predefi ned alarm operation after the set time. (For setting the alarm operation time, refer to the alarm output for an input error of the Door Contact Sensor on page 30.)Present the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit operation time (unit: second) and press .The default is set to “00” second, which means the Door Contact Sensor is disabled.You can specify from 01 to 99.TO SPECIFY THE LIMITED TIME FOR THE KEYPAD INPUTWhen it passes a certain time during your setting using the keypad , all your settings will be ignored and return to the initial state.Specify the delay time between the input of the last key and restoring the previous state.Present the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit operation time (unit: second) and press .The default is set to “20” second.You can specify from 10 to 99.1.2.3.••1.2.3.•SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
26_ basic setupbasic setupTO SPECIFY THE ALARM OUTPUT PORT FOR THE DISMANTLED DEVICESpecify the alarm type for the dismantled device. The alarm rings from the dismantlement of the device to the authentication of the Master Card or a registered card.Present the Master Card to the device.Press Button and Button in sequence and press .Provide the alarm output port and press .The default is set to “02” (alarm).For the alarm output port settings, refer to the output port table on page 28.The alarm for the dismantled device occurs regardless of the operation mode of either Normal or Secure so you simply specify the operation port only. (To specify the operation port, refer to the operation port settings in the output port setting table on page 28.)TO OPEN OR CLOSE THE ENTRY DOORFollow the step below If you want to keep the door open regardless of the authentication process using the Master Card or PIN.Present the Master Card to the device.Press Button and Button in sequence and press .To release opening the door, repeat Step 1 above, select the <> buttons and press .1.2.3.••1.2.•SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 27BASIC SETUPTO SET OR RELEASE THE QUICK MODEThe QUICK mode is applicable to RF ONLY mode (01) and PIN ONLY mode (03) and RF/PIN combination mode (05), which enables you to open the door by simply pressing without the need of the PIN number. (This is useful for the normal business hours when the door entries and exits occur frequently.)Present the Master Card to the device.Press Button and Button in sequence and press .To release the QUICK mode, repeat Step 1 above, select the <> buttons and press .The default is set to “not used”.TO SET OR RELEASE THE TOGGLE MODE FOR THE DOOR RELAYIn the Toggle mode, the door opens if it is closed or vice versa by presenting a registered card or entering the PIN.Present the Master Card to the device.Press Button and Button in sequence and press .To release the Toggle mode, repeat Step 1 above, select the <> buttons and press .The default is set to “not used”.1.2.••1.2.••SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
28_ I/O time setupOutput Port Setting TableYou must specify the port settings using whatever combination of the followings if you want the device to operate in Secure mode or normal + Secure mode.Port Setting Value ExampleOperation mode setting value EX 1) If only the door relay operates in normal and Secure modesNormal and Secure modes: 50Door Relay: +01Output Port Setting Value: 51EX 2) If the alarm relay and the TTL output operate in Secure modeSecure Mode: 00Alarm Relay, TTL: +06Output Port Setting Value: 06Operate only in Secure mode 00Operate in normal mode and Secure mode 50Operation port setting valueOperate the door relay only 01Operate the alarm relay only 02Operate the TTL output only 04Operate the door relay and TTL output 05Operate the alarm relay and TTL output 06TO SPECIFY THE OUTPUT TIME IF THE CARD IS AUTHENTICATEDYou can specify the output time if the card ID is authenticated.When the card ID is authenticated, the door relay and the TTL output operate for a set time.Present the Master Card to the device.Press Button and Button in sequence and press .Enter the two-digit door open time and press .Specify the two-digit TTL output time and press .For instance, if you set the door open time to “03” and TTL to “00”, the door relay operates for 3 seconds for an authenticated card ID.By default, the door relay operates for “03” seconds while the TTL output works for “00” second in normal and Secure modes. You can specify from 00 to 99.❖1.2.3.4.•••I/O time setupSSA-S2000VtGjSSA-S2000V
English _ 29I/O TIME SETUPTO SPECIFY THE OUTPUT TIME IF THE CARD IS NOT AUTHENTICATEDYou can specify the output time if an unregistered card or PIN number fails in getting authenticated.Present the Master Card to the device.Press Button twice and press .Refer to the output port table on page 28 and specify a desired output mode.If you want the alarm relay alone to operate in normal and Secure modes for an unauthenticated card, select the <> buttons and press .Enter the two-digit door relay output time and press .Enter the two-digit alarm relay output time and press .Enter the two-digit TTL output time and press .You can specify a two-digit time from 00 to 99 seconds.By default, only the alarm relay operates for “02” seconds in normal and Secure modes.Other output ports that are not specifi ed for the output mode will not be activated. For instance, if you set the output mode to [5][2] and assign the operation time for each output device by following the steps 4, 5, and 6 above, only the alarm relay will operate.TO SPECIFY THE DURESS TTL OUTPUTIf you enter the Duress code and present a registered card, the TTL output operates. Specify the TTL operation time for this purpose. (For the Duress code, refer to Duress Alarm on page 23.)Present the Master Card to the device.Press Button and Button in sequence and press .Specify the two-digit TTL output time (unit: second) and press .The default is set to “03” second.You can specify a time from 00 to 99 seconds.1.2.3.•4.5.6.•M1.2.3.•SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
30_ I/O time setupI/O time setupTO SPECIFY THE ALARM OUTPUT FOR AN INPUT ERROR OF THE DOOR CONTACT SENSORYou can specify the output port and operation time if an error occurs from the Door Contact Sensor.You must have specifi ed the operation time of the Door Contact Sensor. (Refer to “To specify the operation time of the Door Contact Sensor” on page 25.)Present the Master Card to the device.Press Button and Button in sequence and press .Refer to the output port table on page 28 and specify a desired output mode.If you want the alarm relay alone to operate in normal and Secure modes in case of an error from the Door contact Sensor, select the < > buttons and press .Enter the two-digit door relay output time and press .Enter the two-digit alarm relay output time and press .Enter the two-digit TTL relay output time and press .You can specify a two-digit time from 00 to 99 seconds.By default, all output times are set to “00”.Other output ports that are not specifi ed for the output mode will not be activated. For instance, if you set the output mode to [5][2] and assign the operation time for each output device by following the steps 4, 5, and 6 above, only the alarm relay will operate.TO SPECIFY THE ALARM OPERATION TIME FOR AUX 1Present the Master Card to the device.Press Button and Button in sequence and press .Refer to the output port table on page 28 and specify a desired output mode.If you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port, select the < > buttons and press .Enter the two-digit door relay output time and press .Enter the two-digit alarm relay output time and press .Enter the two-digit TTL relay output time and press .You can specify a two-digit time from 00 to 99 seconds.By default, all output times are set to “00”.Other output ports that are not specifi ed for the output mode will not be activated. For instance, if you set the output mode to [5][2] and assign the operation time for each output device by following the steps 4, 5, and 6 above, only the alarm relay will operate.1.2.3.•4.5.6.••M1.2.3.•4.5.6.••MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 31I/O TIME SETUPTO SPECIFY THE ALARM OPERATION TIME FOR AUX 2Present the Master Card to the device.Press Button and Button in sequence and press .Refer to the output port table on page 28 and specify a desired output mode.If you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port, select the <> buttons and press .Enter the two-digit door relay output time and press .Enter the two-digit alarm relay output time and press .Enter the two-digit TTL relay output time and press .You can specify a two-digit time from 00 to 99 seconds.By default, all output times are set to “00”.Other output ports that are not specifi ed for the output mode will not be activated. For instance, if you set the output mode to [5][2] and assign the operation time for each output device by following the steps 4, 5, and 6 above, only the alarm relay will operate.TO SPECIFY THE ALARM OPERATION TIME FOR AUX 3Present the Master Card to the device.Press Button and Button in sequence and press .Refer to the output port table on page 28 and specify a desired output mode.If you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port, select the <> buttons and press .Enter the two-digit door relay output time and press .Enter the two-digit alarm relay output time and press .Enter the two-digit TTL relay output time and press .You can specify a two-digit time from 00 to 99 seconds.By default, all output times are set to “00”.Other output ports that are not specifi ed for the output mode will not be activated. For instance, if you set the output mode to [5][2] and assign the operation time for each output device by following the steps 4, 5, and 6 above, only the alarm relay will operate.1.2.3.•4.5.6.••M1.2.3.•4.5.6.••MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
32_ I/O time setupI/O time setupTO ACTIVATE OR DEACTIVATE THE DOOR RELAY BY THE DOOR CONTACT SENSORYou can set the Door Contact Sensor to control the door lock. This is to allow the Door Contact Sensor to control the door relay where the sensor keeps the door relay active from the normal opening of the door to its closing.This is useful when the door stays open with just one authentication.Present the Master Card to the device.Press Button and Button in sequence and press .To release the control by the Door contact Sensor, repeat Step 1 above, select the < > buttons and press .The default is set to “disabled”.1.2.•MSSA-S2000VtGjSSA-S2000V
English _ 33ADVANCED SETTINGadvanced settingTO SPECIFY THE TTL OUTPUT OPERATION MODEThis is to switch the TTL output from LOW (0V) to HIGH (5V) when it is activated.Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, repeat Step 1 above, select the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.TO SET THE CHIME BELL FUNCTIONYou can specify the use of the chime bell.Use the chime bell in the TTL level (5V) for this purpose.The default output time is 5 seconds. For changing the output time, refer to “To specify the chime bell operation time” on page 34.Present the Master Card to the device.Press Button twice and press .To release the setting, press the < > buttons and press .The default is set to “use the chime bell”.1.2.•M1.2.•MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
34_ advanced settingadvanced settingTO SPECIFY THE CHIME BELL OPERATION TIMEYou can specify the chime bell operation time.Present the Master Card to the device.Press Button and Button in sequence and press .Specify the two-digit operation time (unit: second) and press .The default is set to “05” second.You can specify a time from 00 to 99 seconds.TO SPECIFY THE INPUT MODE FOR AUX 1You can specify an operation for the auxiliary port 1 when it switches from LOW (0V) to HIGH (5V).Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, repeat Step 1 above, select the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.1.2.3.M1.2.•MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 35ADVANCED SETTINGTO SPECIFY THE INPUT MODE FOR AUX 2You can specify an operation for the auxiliary port 2 when it switches from LOW (0V) to HIGH (5V).Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, press the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.TO SPECIFY THE INPUT MODE FOR AUX 3You can specify an operation for the auxiliary port 3 when it switches from LOW (0V) to HIGH (5V).Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, repeat Step 1 above, select the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.1.2.•M1.2.•MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
36_ advanced settingadvanced settingTO SPECIFY THE INPUT MODE FOR THE EXIT BUTTONYou can specify an operation for the Exit button when it switches from LOW (0V) to HIGH (5V).Present the Master Card to the device.Press Button and Button and Button .To release the setting, press the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.TO SPECIFY THE INPUT MODE FOR THE DOOR CONTACT SENSORYou can specify an operation for the Door Contact Sensor when it switches from LOW (0V) to HIGH (5V).Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, repeat Step 1 above, select the <> buttons and press .The default is set to “switch from HIGH(5V) to LOW(0V)”.1.2.•M1.2.•MSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 37ADDITIONAL FEATURESadditional featuresSSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000VMUTEYou can mute the keypad tone or melody in normal operation.Present the Master Card to the device.Press Button and Button in sequence and press .To release the setting, repeat Step 1 above, select the <> buttons and press .By default, it is set to “enabled”.TO SPECIFY THE USE OF THE TAMPER ALARMYou can maintain the alarm setup in normal operation and release it in case of a service repair requiring the dismantlement of the device. You must set the alarm mode when you have installed the device.For the alarm output port settings, refer to “To specify the alarm output port for the dismantled device” on page 26.Present the Master Card to the device.Press Button twice and press .To release the alarm setting for the dismantled device, repeat Step 1 above, select the <> buttons and press .The default is set to “disabled”.You can release the alarm for the dismantled device by presenting the Master Card or a registered card.1.2.•M1.2.•M
38_ additional featuresadditional featuresTO CHECK THE OUTPUT SPECIFIED FOR A REGISTERED CARD USERYou can check the output setting that you specifi ed in “To specify the output time if the card is authenticated”. (See page 28.)Present the Master Card to the device.Press Button and Button in sequence and press .TO CHECK THE OUTPUT SPECIFIED FOR AN UNREGISTERED CARD USER You can check the output setting that you specifi ed in “To specify the output time if the card is not authenticated”. (See page 29.)Present the Master Card to the device.Press Button and Button and Button .1.2.1.2.SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 39ADDITIONAL FEATURESTO CHECK THE OUTPUT SPECIFIED FOR THE DOOR CONTACT SENSOR ALARM You can check the output setting that you specifi ed in “To specify the alarm output for an input error of the Door contact Sensor”. (See page 30.)Present the Master Card to the device.Press Button and Button in sequence and press .TO CHECK THE OUTPUT SPECIFIED FOR AUX 1 You can check the output setting that you specifi ed in “To specify the alarm operation time for AUX 1”. (See page 30.)Present the Master Card to the device.Press Button and Button in sequence and press .1.2.1.2.SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
40_ additional featuresadditional featuresTO CHECK THE OUTPUT SPECIFIED FOR AUX 2You can check the output setting that you specifi ed in “To specify the alarm operation time for AUX 2”. (See page 31.)Present the Master Card to the device.Press Button and Button in sequence and press .TO CHECK THE OUTPUT SPECIFIED FOR AUX 3You can check the output setting that you specifi ed in “To specify the alarm operation time for AUX 3”. (See page 31.)Present the Master Card to the device.Press Button and Button in sequence and press .1.2.1.2.SSA-S2000VtGjSSA-S2000VSSA-S2000VtGjSSA-S2000V
English _ 41OTHER INFORMATIONother informationINITIAL VALUESThis product operates in the following initial values: For changing the settings or registering/deleting the user card, refer to the applicable section in this document. Entry permitted for a registered card- The door control relay operates for 3 seconds.- The green LED indicator fl ashes for 3 seconds.Entry denied for an unregistered card- The alarm relay operates for 2 seconds.- The red LED indicator fl ashes for 2 seconds. Duress Mode Password : 00The TTL output port produces a signal for 3 seconds in Duress mode.QUICK MODE : Disabled Chime Bell Output : EnabledChime Bell Operating Time : 0.5 secondMelody Sound : EnabledKeypad Input Limited Use : 20 secondsWhen an input signal is sensed : ‘H’  ‘L’ (common for all inputs)When a TTL output signal is sensed : ‘H  L’Patrol Mode Delay Time : 00 minuteDoor Sensor Sensing Time : 00 secondRetry count for an unauthenticated entry : 05 times Alarm for Dismantled Device : DisabledDismantled device Alarm Output Port : 02 (Alarm Relay)Toggle Mode : DisabledControl Lock by the Door Sensor : Disabled1)2)3)4)5)6)7)8)9)10)11)12)13)14)15)
42_ other informationother informationFUNCTION CODESNO. Code Number Function Item111Additional user card registration (RF CARD ONLY MODE)Additional user card registration (RF CARD ONLY MODE)212Additional user card and PIN registration (RF CARD + PIN MODE)Additional user card and PIN registration (RF CARD + PIN MODE)313Additional PIN registration (PIN ONLY MODE)Additional PIN registration (PIN ONLY MODE)414Delete a registered card or PIN numberDelete a registered card or PIN number515Additional user card or PIN registration (RF/PIN combination mode)Additional user card or PIN registration (RF/PIN combination mode)621To specify the output time if the card is authenticatedTo specify the output time if the card is authenticated722To specify the output time if the card is not authenticatedTo specify the output time if the card is not authenticated824Set the Door Contact Sensor alarming timeSet the Door Contact Sensor alarming time925Set the AUX 1 alarming timeSet the AUX 1 alarming time10 26Set the AUX 2 alarming timeSet the AUX 2 alarming time11 27Set the AUX 3 alarming timeSet the AUX 3 alarming time12 29Set the Duress Mode password (2 digits)Set the Duress Mode password (2 digits)13 30Set the TTL output time in Duress ModeSet the TTL output time in Duress Mode14 31To check the output of the registered card user (test on code 21)To check the output of the registered card user (test on code 21)15 32To check the output of the unregistered card userTo check the output of the unregistered card user 16 34To check the output specified for the Door Contact Sensor alarmTo check the output specifi ed for the Door Contact Sensor alarm17 35To check the output specified for AUX 1To check the output specifi ed for AUX 118 36To check the output specified for AUX 2To check the output specifi ed for AUX 219 37To check the output specified for AUX 3To check the output specifi ed for AUX 320 39Set the chime bell ringing timeSet the chime bell ringing time21 41Set the door openSet the door open22 42Release the door openingRelease the door opening23 43Set the QUICK ModeSet the QUICK Mode24 44Release the QUICK ModeRelease the QUICK Mode25 45Toggle to control the door relayToggle to control the door relay26 46Release the toggling to control the door relayRelease the toggling to control the door relay27 47Set to control the door relay using the Door Contact SensorSet to control the door relay using the Door Contact Sensor28 48Release the control of the door relay using the Door Contact SensorRelease the control of the door relay using the Door Contact Sensor
English _ 43OTHER INFORMATIONNO. Code Number Function Item29 51Turn off the soundTurn off the sound30 52Turn on the soundTurn on the sound31 60To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limitTo specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit32 61Sense if AUX 1 switches from L to HSense if AUX 1 switches from L to H33 62Sense if AUX 1 switches from H to LSense if AUX 1 switches from H to L34 63Sense if AUX 2 switches from L to HSense if AUX 2 switches from L to H35 64Sense if AUX 2 switches from H to LSense if AUX 2 switches from H to L36 65Sense if AUX 3 switches from L to HSense if AUX 3 switches from L to H37 66Sense if AUX 3 switches from H to LSense if AUX 3 switches from H to L38 67Sense if the Exit button switches from L to HSense if the Exit button switches from L to H39 68Sense if the Exit button switches from H to LSense if the Exit button switches from H to L40 69Sense if the Door Contact Sensor switches from L to HSense if the Door Contact Sensor switches from L to H41 70Sense if the Door Contact Sensor switches from H to LSense if the Door Contact Sensor switches from H to L42 71Set the TTL output to HSet the TTL output to H43 72Set the TTL output to LSet the TTL output to L44 73Keypad input enabledKeypad input enabled45 74Keypad input disabledKeypad input disabled46 77Chime bell enabledChime bell enabled47 78Chime bell disabledChime bell disabled48 80Set the starting delay time for Patrol ModeSet the starting delay time for Patrol Mode49 81Set the operation time for the Door Contact SensorSet the operation time for the Door Contact Sensor50 82To specify the retry count for an unregistered IDTo specify the retry count for an unregistered ID51 83Set the limitation time for the keypad inputSet the limitation time for the keypad input52 84Set the alarm output port for the dismantled deviceSet the alarm output port for the dismantled device53 88Dismantled device alarm enabledDismantled device alarm enabled54 89Dismantled device alarm disabledDismantled device alarm disabled55 99System Initialization (all settings deleted)System Initialization (all settings deleted)
44_ troubleshootingtroubleshootingTROUBLESHOOTINGIf the product does not function properly, please see the below for trouble shooting.PROBLEM ACTIONWhen I turn on the product, it does not recognize the card with just the 3 LED indicators blinking.1) Check if the product is installed properly and works normally. - In the initial setup of the product or after it is initialized Set the operation mode and register the Master card and user cards as usual because the product is in the initial state. c SSA-S2000V modes available : Mode Number + ENT √ RF Only : 01 + ENT √ RF + P/W : 02 + ENT √ PIN Only : 03 + ENT √ RF or PIN : 05 + ENT d Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) e Enter the user card or PIN number and provide the password according to the mode f Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ For more information about registering the Master Card and the user card, refer to the initial setup section in the user manual.2) If this happens while the product is operating normally (with the Master Card and user card registered) Product malfunction c Power: OFF  ON d If the problem persists, perform the initialization process for the next step. √ For more information about initializing the product, refer to the initialization section in the user manual.3) If the problem persists after you have followed the procedures above, contact a designated service center.The product just switches to normal operation mode while I am registering a user in a set mode or confi gure the settings.1) If no key input is entered within 20 seconds in a set mode, the product will switch to normal operation mode automatically. (normal operation)
English _ 45TROUBLESHOOTINGPROBLEM ACTIONI can not register an additional user card (or PIN).1) Check if the product is installed properly and works normally. - In the initial setup of the product or after it is initializedSet the operation mode and register the Master card and user cards as usual because the product is in the initial state. c SSA-S2000V modes available : Mode Number + ENT √ RF Only : 01 + ENT √ RF + P/W : 02 + ENT √ PIN Only : 03 + ENT √ RF or PIN : 05 + ENT d Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) e Enter the user card or PIN number and provide the password according to the mode f Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ For more information about registering the Master Card and the user card, refer to the initial setup section in the user manual.2) If this happens when you try to register an additional card in normal operation mode - Register the user card only as the Master Card is already registered. c Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) d Command for an additional card registration according to the operation mode √ RF Only : 11 + ENT √ RF + P/W : 12 + ENT √ PIN Only : 13 + ENT √ RF or PIN : 15 + ENT e Enter the user card or PIN number and provide the password according to the mode f Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ For more information about registering the user card, refer to the additional user registration section in the user manual.3) If the problem persists after you have followed the procedures above, contact a designated service center.
46_ troubleshootingtroubleshootingPROBLEM ACTIONThe user card (or PIN) is not deleted.Check the operation status of the product1) Check if the product works properly. - If the product operates normally (and you have the Master Card or the PIN number) c If you have the card to delete √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ Enter the command to delete the user: 14 + ENT √ Enter another card to delete (if you have multiple cards to delete) √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) d If you have lost the card to delete. But you know the card number √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ Enter the command to enable the keypad input: 73 + ENT √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ Enter the command to delete the user: 14 + ENT √ Enter another card to delete and press ENT (if you have multiple cards to delete) √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ For more information about deleting the user card, refer to the user deletion section in the user manual. - If you have lost the Master Card (or PIN) c Registering or deleting the user card is not possible without the Master Card d Initializing the product √ For more information about initializing the product, refer to the initialization section in the user manual.2) If the problem persists after you have followed the procedures above, contact a designated service center.I lost the Master Card and could not register or delete the card or change the settings.1) You must initialize the product if you want to change the device settings without the Master Card (or PIN). (Initializing the product will restore all your settings regarding the Master Card and user cards to the factory default.) c Initialization using the external cable √ Turn off the product and detach it from the wall. √ Connect the orange line of the product to the orange line with the white stripes. √ Turn on the product and check the initial state (LED indicators blink with the increasing bell sound) √ Disconnect the two short-circuited lines and turn off the product2) If the problem persists after you have followed the procedures above, contact a designated service center.
English _ 47TROUBLESHOOTINGPROBLEM ACTIONSSA-S2000V can recognize a presented RF card but can not recognize the RF card number using the keypad.1) Check if the buzzer sounds when you press a key. - If you hear the buzzer sound c Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) d Enter the command to enable the keypad input: 73 + ENT e For more information, refer to the section of enabling or disabling the keypad input for a card number in the user manual. - If you hear the buzzer sound after a certain time c The keypad input will be suspended for one minute (default) if you enter unregistered numbers in 5 consecutive times (default). d To change the retry count for an unauthenticated access √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ Enter the command to set the retry count for an unauthenticated access 82 + ENT √ Enter a new retry count: two digits + ENT (ex. 10 + ENT  the retry count is 10.) √ For more information, refer to the retry count setting section in the user manual. e To change the keypad suspension time √ Master Card (or (PIN): 4 ~ 6 digits (Mode 03 or 05) + ENT) √ Enter the command to change the keypad suspension time: 60 + ENT √ Enter a new time: two digits + ENT (ex. 10 + ENT  the keypad input will be suspended for 10 minutes.) √ For more information, refer to the applicable section for the keypad suspension in the user manual. - If the buzzer stays inactive c Initialize the product.Initializing the product will restore all your settings regarding the Master Card and user cards to the factory default.2) If the problem persists after you have followed the procedures above, contact a designated service center.The Exit button does not work at all.1) Check if the Exit button is connected to SSA-S2000V properly. - Ensure that the Exit button is of the NO type.2) Check if the Exit button works normally. - Check the connection cable between the Exit button and SSA-S2000V for any disconnection or short-circuit. - Try to connect the two lines on the Exit button. c If SSA-S2000V responds when you press the Exit button √ Replace the Exit button  it is defective d If SSA-S2000V does not respond at all √ Initialize the product  the product malfunctions or is damaged.(Initializing will restore all data settings to the default.) √ For more information, refer to the initialization section in the user manual.3) If the problem persists after you have followed the procedures above, contact a designated service center.
48_ troubleshootingtroubleshootingPROBLEM ACTIONThe external reader can the RF card but the RF card data will not be transferred to SSA-S2000V or irrelevant data is transferred.1) Check if the external reader is connected to SSA-S2000V properly.2) Check if the external reader works normally. - Check the connection cable between the external reader and SSA-S2000V for any disconnection or short-circuit. - Check if there occurs a noise on the connection cable between the external reader and SSA-S2000V. c If you have to use a measuring device such as an oscilloscope or a multimeter, please consult with a qualifi ed technician. d Measure the Wiegand communication cable and check if the exit reader works properly.: Check the Wiegand output state of the external reader by referring to the user manual, and replace the reader if it shows an abnormal output. e If there occurs a noise on the Wiegand communication cable using the measuring device: Reinforce the GND line by using the shield line and space line as additional GND points.: Extend the Wiegand communication range along with the stable signal reception using the repeater f For more information, refer to the external reader connection section in the user manual.3) If the problem persists after you have followed the procedures above, contact a designated service center.The door lock does not operate at all.1) Check if the door lock is connected to SSA-S2000V properly.The connection method may differ depending on the type and operation mode (NO, NC) of the door lock.2) Check the status of the door lock - Check the connection cable between the door lock and SSA-S2000V for any disconnection or short-circuit. - Check if the door lock works normally. c If you have to use a measuring device such as an oscilloscope or a multimeter, please consult with a qualifi ed technician. d Remove the door lock from SSA-S2000V, and check the relay output of SSA-S2000V: Replace the door lock if the relay output of SSA-S2000V shows a normal state. e For more information, refer to the door lock connection section in the user manual.3) If the problem persists after you have followed the procedures above, contact a designated service center.
English _ 49product specifi cationsPRODUCT SPECIFICATIONSItem SSA-S2000VUser 512 Users Power / Current DC 12V / Max.180mAReader Port External Reder Port 1ea : 26bit Wiegand for ExitReading Time (Card) 30msDoor Open Time 00~99 Sec. (Default 3Sec.)Input Port 5ea : Exit Button, Door Sensor, Aux#1, #2, #3 Output Port 2ea : 2 Form-C Relay Output (COM, NO, NC) / DC12~18V, Rating Max.2A1ea : Chime Bell Output / DC5V, Rating Max.500mA1ea : TTL Output / DC5V, Rating Max.20mALED Indicator 3 LED Indicators (Red, Green and Orange) Beeper Piezo Buzzer Keypad 12 Key Touch Keypad with Back LightingOperating Temperature -30°C to +50°COperating Humidity 10% to 90% relative humidity non-condensing Color / Material Silver with Black/ Polycarbonate & Aluminum Die casting Dimension (W x H x D(mm))87.0 x 109.0 x 25.0Weight 440g ±10Correct disposal of batteries in this product(Applicable in the European Union and other European countries with separate battery return systems.)This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.Correct Disposal of This Product (Waste Electrical & Electronic Equipment)(Applicable in the European Union and other European countries with separate collection systems)This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.PRODUCT SPECIFICATIONS
P/No. : Z8100239101Awww.samsungsecurity.comwww.samsungtechwin.comSAMSUNG TECHWIN CO., LTD.Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745SAMSUNG TECHWIN EUROPE LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPSTEL : +44-1932-45-5300 FAX : +44-1932-45-5325SAMSUNG TECHWIN AMERICA Inc.1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195www.samsungcctvusa.comSALES NETWORK

Navigation menu