Harris RF Communications Division XG-100P00 Unity Multiband Portable User Manual xg 100 ops

Harris Corporation RF Communications Division Unity Multiband Portable xg 100 ops

Contents

Manual 1

PUBLICATION NUMBER:DECEMBER 2009Rev. -10515-0372-4200UNITY™ XG-100PFull-SpectrumMultiband RadioOperation Manual
RHARRIS   CORPORATION   RF   COMMUNICATIONS   DIVISION1680 University Avenue    Rochester, New York  14610-1887   USATel: 585-244-5830. Fax: 585-242-4755.  http://www.harris.comPUBLICATION NUMBER: 10515-0372-4200DECEMBER 2009Rev. -Information and descriptions contained herein are the property of HarrisCorporation. Such information and descriptions may not be copied orreproduced by any means, or disseminated or distributed without theexpress prior written permission of Harris Corporation, RFCommunications Division, 1680 University Avenue, Rochester, NewYork 14610-1887.This manual is based on Firmware Version 1.0Copyright  2009 by Harris CorporationAll Rights ReservedUNITY™ XG-100PFULL-SPECTRUM MULTIBAND RADIOOPERATIONS MANUAL
This product was developed using GEOTRANS, a product of the National Geospatial Intelligence Agency and U.S. Army Engineering Research and Development Center. Use of this software does not indicate endorsement or approval of the product by the Secretary of Defense or the National Geospatial Intelligence Agency.This device made under license under one or more of the following US patents: 4,590,473; 4,636,791; 5,148,482; 5,185,796; 5,271,017; 5,377,229; 4,716,407; 4,972,460; 5,502,767; 5,146,697; 5,164,986; 5,185,795.The Advanced Multi-Band Excitation implementation 2 (AMBE+2) voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656,  #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs, alterations or substitutions of recommended parts made by the user to this equipment not approved by the manufacturer could void the user's authority to operate the equipment in addition to the manufacturer's warranty.This product conforms to the European Union Waste from Electric and Electronic Equipment (WEEE) Directive 2002/96/EC. Do not dispose of this product in a public landfill. This product should be taken to a recycling center at the end of its life.
XG-1005INTRODUCTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   11EQUIPMENT DESCRIPTION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12STORAGE GUIDELINES   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12BASIC SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   13ASSEMBLE THE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14REMOVING THE BATTERY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16REMOVING OPTIONAL BELT CLIP  . . . . . . . . . . . . . . . . . . . . . . . . . 16BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   17XG-100P CONTROLS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18TOP DISPLAY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20MAIN DISPLAY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21MENU NAVIGATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22BEFORE FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23POWER ON AND SET VOLUME   . . . . . . . . . . . . . . . . . . . . . . . . . . . 23SELECT CHANNEL BANK   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24SELECT CHANNEL USING KNOB  . . . . . . . . . . . . . . . . . . . . . . . . . . 24TURN ENCRYPTION ON OR OFF  . . . . . . . . . . . . . . . . . . . . . . . . . . 25SELECT ZONE USING MENUS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26MAKE AN INDIVIDUAL CALL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28MAKE A PRIORITY CALL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30SELECT A NEW TALKGROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31USE TALKAROUND TO BYPASS REPEATER   . . . . . . . . . . . . . . . . 33START SCAN   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35STOP SCAN   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37NUISANCE DELETE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38VIEW GPS INFORMATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40EMERGENCY OPERATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Receiving an Emergency Call  . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Declaring an Emergency Call  . . . . . . . . . . . . . . . . . . . . . . . . . . . 43ADVANCED OPERATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . .   45CREATE KEYS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Create Key in the KVL 3000 Plus  . . . . . . . . . . . . . . . . . . . . . . . . 46Create Keygroup in the KVL 3000 Plus . . . . . . . . . . . . . . . . . . . . 47
6XG-100LOAD KEYS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48LOAD KEYGROUPS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ZEROIZE ALL FROM RADIO   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52ZEROIZE KEYS USING KVL 3000 PLUS  . . . . . . . . . . . . . . . . . . . . . 53ZEROIZE KEYGROUPS USING KVL 3000 PLUS  . . . . . . . . . . . . . . 55ZEROIZE ALL FROM KVL 3000 PLUS  . . . . . . . . . . . . . . . . . . . . . . . 57ACTIVATE/VIEW MISSION PLAN   . . . . . . . . . . . . . . . . . . . . . . . . . . 58CH INFO MENU   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60SETTINGS MENU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Audio Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68GPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Bluetooth  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Clock Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Battery Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76SHORTCUT MENU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Start or Stop Scan (Shortcut Menu)   . . . . . . . . . . . . . . . . . . . . . . 80Monitor and Squelch Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Nuisance Delete   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Mute/Unmute Speaker   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Lock Keypad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Flip Top Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85SET UP SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Zone Scan vs Custom Scan  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Add New Scan List   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Edit Scan List   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Priority 1 Channel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Rename Scan List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Set or Remove Priority (PRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Delete Scan List   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Set Active Scan List   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95MESSAGE MENU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96UTILITY MENU   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   101PROGRAMMING VIA CPA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102EDIT CHANNEL   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102PROGRAMMABLE HOT KEY AND BUTTONS . . . . . . . . . . . . . . . . . 108
XG-1007REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   109MARINE FREQUENCIES   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   125
8XG-100This page intentionally left blank.
9The XG-100P has been tested and complies with the Federal Communications Commission (FCC) RF exposure limits for “Occupational Use Only.” In addition, this radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:•FCC Office of Engineering and Technology (OET) Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields•American National Standards Institute (ANSI) (C95.1 – 1992), Institute of Electrical & Electronics Engineers (IEEE) Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz•American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields – RF and MicrowaveWARNING - Before operating the XG-100P radio, read the safety and RF exposure guidelines contained in safety booklet, 10515-0372-4000, included with your radio.
10CHANNEL KNOBPOWER / VOLUME KNOBENCRYPTIONSWITCHBANK SELECTORPROGRAMMABLEHOT KEYPTT BUTTONPROGRAMMABLEBUTTONSSOFT KEYSSELECT/SHORTCUTBUTTONNAVIGATORKEYPAD**SOFT-KEYDISPLAYSCL-0372-4200-0007BSPEAKERMICROPHONE* FRONT DISPLAYEMERGENCY BUTTONINDICATOR LEDTOP DISPLAYANTENNACONNECTORBATTERYMICROPHONE*(REAR)*DUAL MICROPHONE SYSTEM USED FOR NOISE CANCELLATION** USEAS HOME KEY FORNAVIGATION  BACK TO MAIN SCREEN
Section PageEquipment Description  . . . . . . . . . . . . . . .12Storage Guidelines . . . . . . . . . . . . . . . . . .12INTRODUCTION 1
12XG-100INTRODUCTI ON1EQUIPMENT DESCRIPTIONYour XG-100P provides full-spectrum multiband coverage:•136 to 174 MHz, VHF, 1 watt, 2 watts, 3 watts, 6 watts output•380 to 520 MHz, UHF-Low, UHF-High, 1 watt, 2 watts, 3 watts, 5 watts output•762 to 870 MHz, 700/800 bands, 0.5 watt, 1 watt, 2 watts, 3 watts outputThe XG-100P has the following capabilities:•Project 25 (P25) Conventional•P25 Trunking (Future)•Analog FM•Advanced Encryption Standard, 256-bit (AES-256)/Digital Encryption Standard Output Feedback (DES-OFB) Encryption•Global Positioning System (GPS)•Bluetooth®For optional accessories, refer to Accessories. Additional accessories may have been added since publication of this manual; contact Harris for more information.STORAGE GUIDELINESStore your XG-100P and batteries in a clean, cool (not exceeding 86 °F [+30 °C]), dry and ventilated storage area.
Section PageAssemble the Radio . . . . . . . . . . . . . . . . .14Removing the Battery . . . . . . . . . . . . . . . .16Removing Optional Belt Clip . . . . . . . . . . .16BASICSETUP 2
14XG-100BASI C SE T UP2ASSEMBLE THE RADIOa. Make sure batteries are charged per the charger manual (refer to 10515-0372-4010, supplied with the charger).b. To attach optional clip, slide into groove in back of the radio above battery compartment.c. Lift clip, if installed, and slide top of battery into top of battery compartment at the rear of the radio.d. Press down on bottom side of battery until it snaps into place.Radio may need to be set for battery type (Battery Settings).CAUTION: Do not overtighten the antenna as damage could result.WARNING: Only use Harris charger approved for battery chemistry. Injury could occur from improper charger use.
15XG-100BASI C SET UP2CL-0372-4200-0002BATTERYBELT CLIP(OPTIONAL)ANTENNA
16XG-100BASI C SE T UP2REMOVING THE BATTERYTo remove, press and hold tab, lift battery clip, then pull battery up and out of the radio.REMOVING OPTIONAL BELT CLIPRemove the battery before removing the clip. To remove belt clip, press and hold tab towards top of battery, then slide out of groove in back of the radio.CL-0372-4200-0009CL-0372-4200-0008PRESS  TAB TO REMOVE CLIP
Section PageXG-100P Controls. . . . . . . . . . . . . . . . . . .18Top Display . . . . . . . . . . . . . . . . . . . . . . . .20Main Display . . . . . . . . . . . . . . . . . . . . . . .21Menu Navigation . . . . . . . . . . . . . . . . . . . .22Before First Time Use . . . . . . . . . . . . . . . .23Power On and Set Volume . . . . . . . . . . . .23Select Channel Bank  . . . . . . . . . . . . . . . .24Select Channel Using Knob  . . . . . . . . . . .24Turn Encryption On or Off . . . . . . . . . . . . .25Select Zone Using Menus . . . . . . . . . . . . .26Make an Individual Call. . . . . . . . . . . . . . .28Make a Priority Call. . . . . . . . . . . . . . . . . .30Select a New Talkgroup  . . . . . . . . . . . . . .31Use Talkaround to Bypass Repeater  . . . .33Start Scan . . . . . . . . . . . . . . . . . . . . . . . . .35Stop Scan . . . . . . . . . . . . . . . . . . . . . . . . .37Nuisance Delete . . . . . . . . . . . . . . . . . . . .38View GPS Information. . . . . . . . . . . . . . . .40Emergency Operation . . . . . . . . . . . . . . . .42BASICOPERATIONS 3
18XG-100BASIC OPERATI ONS3XG-100P CONTROLS1. CHANNEL KNOB2. POWER / VOLUME     KNOB3. ENCRYPTION    SWITCH5. BANK SELECTOR6. PROGRAMMABLE    HOT KEY7. PTT BUTTON8. PROGRAMMABLE    BUTTONS18. SOFT KEYS19. SELECT/SHORTCUT BUTTON20. NAVIGATOR21. KEYPAD**17. SOFT-KEY      DISPLAYSCL-0372-4200-0005B14. SPEAKER15. MICROPHONE* 16. FRONT DISPLAY11. EMERGENCY       BUTTON12. INDICATOR LED13. TOP DISPLAY10. ANTENNA      CONNECTOR9. BATTERY4. MICROPHONE*    (REAR)*DUAL MICROPHONE SYSTEM USED FOR NOISE CANCELLATION** USEAS HOME KEY FORNAVIGATION  BACK TO MAIN SCREEN
19XG-100BASIC OPERATI ONS3Table 1. XG-100P Controls, Indicators, and ConnectorsKey Control/Indicator Function1 Channel Knob Used to select one of 16 channels2 Power/Volume Knob Turn clockwise to power on radio and increase volume of audio heard in speaker. 3 Encryption Switch Selects between encrypted and unencrypted operation. Ø - EncryptionO - No Encryption4 Microphone (Rear) Used with microphone on the front of the radio to form a dual microphone system that is used for noise cancellation. Noise cancellation improves the quality of transmitted voice. 5 Bank Selector Used to select one of three banks: A, B, or C (Select Channel Bank). 6 Programmable Hot KeyUsed to select a commonly used function as an alternative to navigating menus. This is configured in the Communications Planning Application (CPA).7 Push-To-Talk (PTT) ButtonPress to transmit. Make sure PTT is enabled.8 Programmable ButtonsUsed to select a commonly used function as an alternative to navigating menus. These are configured in the CPA.9 Battery Battery - Refer to Assemble the Radio for battery connection and removal.10 Antenna Connector Provides Subminiature version A (SMA) antenna connector.11 Emergency Button Used to place radio in emergency mode (Emergency Operation). This button can be disabled by setting to unassigned in the CPA.12 Indicator Light Emitting Diode (LED)Indicates radio status.Red = actively transmitting.Green = actively receiving.13 Top Display Top display shows summary of status such as channel, battery, and scanning. This can be configured for viewing from the front or rear of the radio (Display Settings).14 Speaker Radio speaker which can be muted (Audio Settings). Volume can be adjusted using the Power/Volume knob.15 Microphone Used with microphone on the rear of the radio to form a dual microphone system that is used for noise cancellation. Noise cancellation improves the quality of transmitted voice.
20XG-100BASIC OPERATI ONS3TOP DISPLAYTop display can be oriented for viewing from the front or rear of the radio. Refer to Display Settings for configuration.16 Front Display Front display shows complete status and radio menus.17 Soft-Key Displays These are displays of menus that are accessed by pressing a soft-key directly below text (Menu Navigation)18 Soft Keys Accesses menus labeled in text directly above button (Menu Navigation).19 Select/Shortcut ButtonUsed to select menu highlighted by navigator. Also used for shortcut menu from main screen (Shortcut Menu).20 Navigator Provides up, down, left, right menu navigation. Also used for select and shortcut menu access.21 Keypad Used to enter text or numbers and to quickly access menus.You can use   as a home key to quickly navigate back to the main screen. Table 1. XG-100P Controls, Indicators, and Connectors (Continued)Key Control/Indicator FunctionCHANNEL NUMBER*BATTERY LEVELCL-0372-4200-0010ASCAN INDICATOR*APPEARS IN EMERGENCY!
21XG-100BASIC OPERATI ONS3MAIN DISPLAYThe main display appears after power up or after exiting from the menus. ACTIVITY AREA:RECEIVINGSCANNINGEMERGENCY2 SOFT KEY LABELSRECEIVINGTRANSMITTINGSTANDBYBATTERY LEVELSCANNING ENABLEDBLUETOOTH ENABLEDPOWERENCRYPTIONTALKAROUNDMONITORGPSNOISE CANCELSTATUS AREA:LOW BATTERY LEVELVERY LOW BATTERY LEVELTIME**HARRIS LOGO DISPLAYS IF GPS HAS NOT ACQUIRED AFTER POWER UPCL-0372-4200-0003BLUETOOTH PAIREDPTT DISABLEDRX ONLYTONES MUTEDBATTERY EXHAUSTEDALERTSPEAKER MUTEEMERGENCY
22XG-100BASIC OPERATI ONS3MENU NAVIGATIONCL-0372-4200-0006CPRESSTHEN SELECTSUBMENUMAINDISPLAYPRESS FOR CH INFOPRESS FOR MENU12356789PRESSTHEN SELECTKEYPAD 1 - 9 CAN ALSOBE USED FOR DIRECT ACCESS (EXAMPLE: PRESS 4 FOR ZONE)MAINMENU5
23XG-100BASIC OPERATI ONS3BEFORE FIRST TIME USEMake sure XG-100P has:•Fully charged battery•Antenna attached•Mission plan and radio programmed using the CPA•Keys are loaded•Mission plan is activated using radio menusPOWER ON AND SET VOLUMEThe power switch and volume control are within the same control.1. Turn   clockwise to power on XG-100P. 2. Set   to desired volume level.
24XG-100BASIC OPERATI ONS3SELECT CHANNEL BANKThe XG-100P can be programmed with up to 1250 channels, 48 channels per zone, with 16 channels in each of the three banks:•Bank A - Channel A1 - A16•Bank B - Channel B1 - B16•Bank C - Channel C1 - C16SELECT CHANNEL USING KNOB1. Use   to set bank.1. Use   to set channel 1 - 16.NEWBANKNEWCHANNEL
25XG-100BASIC OPERATI ONS3TURN ENCRYPTION ON OR OFFRefer to Create Keys and Load Keys.1. Use   to set encryption:•Ø - Encryption•O - No encryptionKey appears when encryption is used for channel that is digital and programmed to be encrypted. Analog channels do not show the encryption key.NOTE: When encryption is turned on and you use a digital channel not configured for encryption, the radio will not allow PTT. The screen displays CLEAR TX DENIED.When encryption is turned on and you use an analog channel not configured for encryption, the radio will PTT. The signal will be transmitted unencrypted.
26XG-100BASIC OPERATI ONS3SELECT ZONE USING MENUSA zone is a group of channels, and can be programmed by agency or geographical region. For example, a zone could be for fire, police, New York, Los Angeles, etc.1. At main display, use  for main menu.2. Use  to highlight and select ZONE or just press .A mission plan could have up to 64 zones, independent of banks or channels.3. Use  to view zone.134579826ZONE
27XG-100BASIC OPERATI ONS34. Use to highlight zone.5. Use   to select highlighted zone. If VIEW ZONES was selected, this screen appears allowing you to view the channels in the zone.6. Use   to scroll through the zones.7. Use   to select highlighted zone. New zone appears.ZONEZONENEW ZONEMAIN SCREEN
28XG-100BASIC OPERATI ONS3MAKE AN INDIVIDUAL CALLAn individual call is used to make a call to one radio as opposed to a group of radios. An individual call can only be made on digital channels. On the receiving radio, the calling station name will appear in the activity area.1. At main display, use   for main menu.2. Use  to highlight and select CALL or just press .3. Use  to highlight and select INDIVIDUAL CALL. 1345798265JK L
29XG-100BASIC OPERATI ONS34. Use to highlight and select individual.  5. Use PTT to make the call.  6. To end call, use   to select END CALL. INDIVIDUALTO BE CALLEDMAIN SCREEN
30XG-100BASIC OPERATI ONS3MAKE A PRIORITY CALLA priority call is used to make a call on the priority channel. Priority calls can only be made on digital channels.1. At main display, use   for main menu.2. Use  to highlight and select CALL or just press .3. Use  to highlight and select ENABLE for PRIORITY MODE. 4. Use   to return to main screen. 1345798265JK L
31XG-100BASIC OPERATI ONS3SELECT A NEW TALKGROUPA talkgroup is a group of radios that you would want to have private conversations with. These groups could be divided into areas such as state, region, county, or large special events. A talkgroup call can only be made on digital channels. On the receiving radio, the calling station name will appear in the activity area. 5. Use PTT to make the call. 1. At main display, use   for main menu.2. Use to highlight and select CALL or just press .PRIORITYCHANNELAPPEARSWHEN KEYEDMAIN SCREEN1345798265JK L
32XG-100BASIC OPERATI ONS33. Use  to highlight and select CHANGE TLKGRP. 4. Use  to highlight and select talkgroup.5. Use   to return to main screen. 6. Use PTT to make the call. TALKGROUPTO BE CALLEDMAIN SCREEN
33XG-100BASIC OPERATI ONS3USE TALKAROUND TO BYPASS REPEATERYou can bypass the repeater system to communicate directly with other radios on your current channel’s receive frequency. This is useful if you are out of range of a repeater or if a repeater is busy. You will need to be in range of the other radio.1. At main display, use   for main menu.2. Use to highlight and select CALL or just press .3. Use to change TALKAROUND MODE to ENABLED. 1345798265JK L
34XG-100BASIC OPERATI ONS3Talkaround icon appears. Calls will now be made on the receive frequency until you disable talkaround mode.TALKAROUNDENABLED
35XG-100BASIC OPERATI ONS3START SCANThis procedure assumes that the scan list has been added and is not in active scan. Refer to Set up Scan or Stop Scan.NOTE: For shortcut method of starting scan, refer to Start or Stop Scan (Shortcut Menu).1. At main display, use   for main menu.2. Use to highlight and select SCAN or just press .3. Use to highlight SCAN METHOD.4. Use to select ZONE SCAN or CUSTOM SCAN for scan method (Zone Scan vs Custom Scan).1345798262ABC
36XG-100BASIC OPERATI ONS35. Use to highlight START SCAN. Text changes to red STOP SCAN. Radio is scanning at this point. Additional scanning indications can be seen in the next step. 6. Use   to exit scan menu. SCANNINGDISPLAYMAIN SCREEN
37XG-100BASIC OPERATI ONS3STOP SCANThis procedure is used to stop an active scan. Refer to Start Scan.1. At main display, use   for main menu.2. Use to highlight and select SCAN or just press .3. Use to highlight STOP SCAN. 4. Use   to exit scan menu. 1345798262ABC
38XG-100BASIC OPERATI ONS3NUISANCE DELETEA channel can temporarily be deleted from the scan list if it is not a priority channel. The radio must be scanning for nuisance delete.1. At main display, use   for main menu.2. Use  to highlight and select SCAN or just press .3. Use  to highlight and select ZONE LISTS or CUSTOM LISTS.1345798262ABC
39XG-100BASIC OPERATI ONS3Custom scan configuration screens are shown here. Zone scan configuration is similar.4. Use   to highlight scan list.  indicates the active scan list.5. Use   to select OPTIONS. 6. Use   to highlight and select VIEW/EDIT. 7. Use   to highlight channel. 8. Use   to select OPTIONS. 9. Use   to highlight and select NUISANCE.Nuisance channel will not be scanned. Channel will return to scan list when you cycle radio power or activate mission plan.
40XG-100BASIC OPERATI ONS3VIEW GPS INFORMATIONYou can use the internal Global Positioning System (GPS) receiver to view your position and satellite information. Remember, GPS:•Signal is greatly diminished inside buildings, tunnels, heavily forested areas etc. •Requires unobstructed view of the sky.GPS may not work at all under some materials, especially metal.10. Use   to exit channel list.  11. Use   to exit zone or custom lists display. 1. At main display, use   for main menu.SCANNINGDISPLAYMAIN SCREEN
41XG-100BASIC OPERATI ONS32. Use to highlight and select GPS or just press .You can observe GPS status:•GPS TRACKING - GPS has acquired satellite signal. GPS time appears on top of display.•GPS SEARCHING - GPS has not acquired. Harris logo appears on top of display if GPS has not tracked after last power up of the radio.•LAST KNOWN POS - GPS acquired since power up has lost signal. Information displayed was from radio it was previously tracking.3. Use   to select NEXT.4. Use to highlight and select to view satellite information.134579826GPS STATUSGPS TIME** WHEN TRACKING
42XG-100BASIC OPERATI ONS3EMERGENCY OPERATIONThe XG-100P can be programmed to enable emergency mode. ‘Emergency’ text displays on dispatcher console if an emergency signal is received from another XG-100P on a digital channel. Receiving an Emergency CallWhen receiving an Emergency Call, an alert beep is present (if tones are enabled) and an emergency indication is displayed. When receiving an emergency on a digital channel, the Unit Identification (ID) appears in the activity area.While the emergency display is active, you can press the PTT to respond to the emergency caller.When receiving an emergency on an analog channel, the radio only indicates that it is receiving.
43XG-100BASIC OPERATI ONS3Declaring an Emergency Call1. Press .For digital channels, the radio transmits talkgroup or radio ID to dispatch console or receiving radio.The radio will go through transmit and receive cycles if configured.You can speak into the microphone while the radio is transmitting or press PTT to talk.2. To exit emergency, either power cycle the radio or select EXIT EMERGENCY from the call menu.
44XG-100BASIC OPERATI ONS3This page intentionally left blank.
Section PageCreate Keys  . . . . . . . . . . . . . . . . . . . . . . .46Load Keys . . . . . . . . . . . . . . . . . . . . . . . . .48Load Keygroups . . . . . . . . . . . . . . . . . . . .50Zeroize All from Radio  . . . . . . . . . . . . . . .52Zeroize Keys Using KVL 3000 Plus  . . . . .53Zeroize Keygroups Using KVL 3000 Plus.55Zeroize All from KVL 3000 Plus . . . . . . . .57Activate/View Mission Plan . . . . . . . . . . . .58CH INFO Menu . . . . . . . . . . . . . . . . . . . . .60Settings Menu . . . . . . . . . . . . . . . . . . . . . .62Shortcut Menu. . . . . . . . . . . . . . . . . . . . . .78Set up Scan  . . . . . . . . . . . . . . . . . . . . . . .85Message Menu . . . . . . . . . . . . . . . . . . . . .96Utility Menu . . . . . . . . . . . . . . . . . . . . . . . .97ADVANCEDOPERATIONS 4
46XG-100ADVANCED OPERATI ONS4CREATE KEYSRefer to the Motorola KVL 3000 Plus Key Variable Loader (KVL) User's Guide for advanced programming and setup instructions.Create Key in the KVL 3000 PlusYou can generate a single Type-3 key in the KVL 3000 Plus key loading device:a. Turn on the KVL 3000 Plus.b. Select KEYS.c. Select NEW.d. Enter a number between 00001 and 04095 or between 61440 and 65535 at Common Key References (CKR) prompt. The number must be unique on the KVL 3000 Plus.e. Choose DES-OFB or AES-256 as the algorithm.f. Select ACCEPT.g. Enter Key Identification (KID) from 0000 to FFFF. The number must be different for each key of a particular algorithm in the KVL 3000 Plus.h. Enter a 16-digit hexadecimal number as the Key value. DES-OFB keys are 16 digits while AES keys are 64 digits (32 bytes [256 bits]). Odd parity checks are made between every two digits for DES-OFB keys. Parity checks are not made for AES-256 keys.i. KVL 3000 Plus will display SLOT FILLED, press ENTER.j. A message is displayed when complete: KEY WAS CREATED SUCCESSFULLY.k. Refer to Load Keys for loading a key into the radio.
47XG-100ADVANCED OPERATIONS4Create Keygroup in the KVL 3000 PlusYou can generate a group of Type-3 keys in the KVL 3000 Plus:a. Turn on the KVL 3000 Plus.b. Select Esc.c. Select GROUPS.d. Select NEW.e. Enter a Group Name (up to seven characters).NOTEThe XG-100 can store both DES-OFB and AES-256 keys, however, only one type may be loaded at a time. A keyset must contain only DES-OFB or only AES-256 keys.f. Select CKRs from the programmed list until all desired CKRs are selected.g. Select DONE. Refer to Load Keys for loading a keyset into the radio.
48XG-100ADVANCED OPERATI ONS4LOAD KEYSType 3 Digital Encryption Standard Output Feedback (DES-OFB) and Advanced Encryption Standard, 256-bit (AES-256), encryption methods are supported. The Type 3 Encryption keys are loaded via a Motorola KVL 3000 Plus device using Telecommunications Industry Association (TIA)/Project P25 (P25) key fill device protocol. Make sure that valid keys have been created and stored in the KVL 3000 Plus before proceeding.1. Power on KVL 3000 Plus.2. Connect KVL 3000 Plus to side connector using a 12082-0400-A1 cable.3. Use  to highlight and select:•AES KEYS•DES KEYSSIDECONNECTOR
49XG-100ADVANCED OPERATIONS4At the KVL 3000 Plus:4. Select TARGET.5. Select LOAD.6. Select KEY.7. Using ◄or ►, select:•DES-OFB key•AES-256 key8. Press LOAD.9. Verify that the KVL 3000 Plus screen displays LOADED SUCCESSFULLY OK. 10. Select OK on the KVL 3000 Plus.11. Repeat for additional keys.12. Remove the KVL 3000 Plus cable from the radio.EscCtrlShiftBackPwr1 23A4 56 B7 89 CG FE D
50XG-100ADVANCED OPERATI ONS4LOAD KEYGROUPSMake sure that valid keygroups have been created and stored in the KVL 3000 Plus before proceeding.1. Power on KVL 3000 Plus.2. Connect KVL 3000 Plus to side connector using a 12082-0400-A1 cable.3. Use  to highlight and select:•AES KEYS•DES KEYSSIDECONNECTOR
51XG-100ADVANCED OPERATIONS4At the KVL 3000 Plus:4. Select TARGET.5. Select LOAD.6. Select GROUP.7. Using ◄or ►, select:•DES-OFB keygroups•AES-256 keygroups8. Press LOAD.9. Verify that the KVL 3000 Plus screen displays LOADED SUCCESSFULLY OK. 10. Select OK on the KVL 3000 Plus.11. Repeat for additional groups.12. Remove the KVL 3000 Plus cable from the radio.EscCtrlShiftBackPwr1 23A4 56 B7 89 CG FE D
52XG-100ADVANCED OPERATI ONS4ZEROIZE ALL FROM RADIOIt may be necessary to remove the keys because of compromise or expiration. 1. At main display, use   for main menu.2. Use  to highlight and select SECURITY or just press .3. Use  to highlight and select ZEROIZE KEYS.4. Use  to highlight and select YES if you want to remove the keys.134579826
53XG-100ADVANCED OPERATIONS4ZEROIZE KEYS USING KVL 3000 PLUSRefer to the KVL 3000 Plus User’s Guide for advanced instructions.5. Use to select OK.1. Power on KVL 3000 Plus.2. Connect KVL 3000 Plus to side connector using a 12082-0400-A1 cable.CAUTION: Ensure correct keyset is selected.3. Use to highlight and select:•AES KEYS•DES KEYSSIDECONNECTOR
54XG-100ADVANCED OPERATI ONS4At the KVL 3000 Plus:4. Select TARGET.5. Select ZERO.6. Select KEY.7. Using ◄or ►, select the key to remove from the radio.8. Press ZERO.9. Verify that the KVL 3000 Plus screen displays ZEROIZED SUCCESSFULLY OK. 10. Select OK on the KVL 3000 Plus.11. Repeat for additional keys.12. Remove the KVL 3000 Plus cable from the radio.13. Set  to O to remove all AES and DES keys.EscCtrlShiftBackPwr1 23A4 56 B7 89 CG FE D
55XG-100ADVANCED OPERATIONS4ZEROIZE KEYGROUPS USING KVL 3000 PLUSRefer to the Motorola KVL 3000 Plus User's Guide for advanced instructions.1. Power on KVL 3000 Plus.2. Connect KVL 3000 Plus to side connector using a 12082-0400-A1 cable.CAUTION: Ensure correct keyset is selected.3. Use to highlight and select:•AES KEYS•DES KEYSSIDECONNECTOR
56XG-100ADVANCED OPERATI ONS4At the KVL 3000 Plus:4. Select TARGET.5. Select ZERO.6. Select GROUP.7. Using ◄or ►, select the key to remove from the radio.8. Press ZERO.9. Verify that the KVL 3000 Plus screen displays ZEROIZED SUCCESSFULLY OK. 10. Select OK on the KVL 3000 Plus.11. Repeat for additional keys.12. Remove the KVL 3000 Plus cable from the radio.13. Set  to O to remove all AES and DES keys.EscCtrlShiftBackPwr1 23A4 56 B7 89 CG FE D
57XG-100ADVANCED OPERATIONS4ZEROIZE ALL FROM KVL 3000 PLUSRefer to the KVL 3000 Plus User's Guide for advanced programming and setup instructions.1. Power on KVL 3000 Plus.2. Connect KVL 3000 Plus to side connector using a 12082-0400-A1 cable.This appears on radio. All AES and DES keys are zeroized regardless of selection.At the KVL 3000 Plus:3. Select TARGET.4. Select ZERO.5. Select ALL.6. Select YES.7. Verify that the KVL 3000 Plus screen displays ZEROIZED SUCCESSFULLY OK. 8. Select OK on the KVL 3000 Plus.SIDECONNECTOREscCtrlShiftBackPwr1 23A4 56 B7 89 CG FE D
58XG-100ADVANCED OPERATI ONS4ACTIVATE/VIEW MISSION PLANMission plans contain radio programming information such as frequencies, channels, stations, and talkgroups. Up to 10 different mission plans can be stored in the radio, but only one can be activated at one time.9. Remove the KVL 3000 Plus cable from the radio.1. At main display, use   for main menu.2. Use  to highlight and select PROGRAM or just press .134579826
59XG-100ADVANCED OPERATIONS43. Use   to highlight and select mission plan.  indicates the active mission plan. 4. Use   to select OPTIONS. 5. Use   to highlight and select:•ACTIVATE PLAN to load the plan for use by the radio.•VIEW PLAN INFO - to view mission plan information.If plan is activated, radio displays series of screens indicating status, ending with a PLAN COMPLETE followed by name of plan.6. Use   to select OK.
60XG-100ADVANCED OPERATI ONS4CH INFO MENUThe Channel Information (CH INFO) menu displays information about the currently selected channel. If plan is being viewed, radio displays the plan’s filename and file size. Plan information appears if field was filled out in the CPA.7. Use   to select BACK.8. Repeatedly use   to exit menus.9. New plan appears if activated.1. At main display, use   for channel information menu.NEWPLANMAIN SCREEN
61XG-100ADVANCED OPERATIONS42. Use  to scroll through the programmed channel settings.3. Additional settings can be found by scrolling down.4. If a channel was programmed to allow editing by properly trained operator, you will be able to use the steps that follow.5. Use to select EDIT CHAN.6. Enter passwordNOTE: Password remains active until power cycle.Refer to Edit Channel.
62XG-100ADVANCED OPERATI ONS4SETTINGS MENUThe settings menu allows you to change global radio settings such as audio, display, and clock.1. At main display, use   for main menu.2. Use   to highlight and select SETTINGS or just press .3. Use   to highlight setting. 134579826
63XG-100ADVANCED OPERATIONS44. Additional settings can be found by scrolling down.5. Proceed to:•Audio Settings•Display Settings•GPS Settings•Bluetooth•Clock Settings•Battery Settings
64XG-100ADVANCED OPERATI ONS4Audio SettingsSet audio settings such as speaker mute, noise cancellation, PTT, etc.1. Enter Settings Menu.2. Use   to highlight and select AUDIO SETTINGS.
65XG-100ADVANCED OPERATIONS43. Use   to change settings as desired:•SPEAKER - Speaker audio can be muted or unmuted. The radio can be used with a wired lapel microphone.•NOISE CANCELLATION - Enable or disable noise cancellation. Noise cancellation reduces background noise during transmit. •PTT - Enable or disable Push-To-Talk (PTT). Disable to prevent accidental keying, such as when radio is in holster or you are getting into a car.•TONES - Enable or disable alert tones (Ta b l e 1 ).4. Use   to exit menu.
66XG-100ADVANCED OPERATI ONS4Table 1. Alert TonesTone Description Sound/DurationReady To Talk Tone Unencrypted (Analog FM or P25 digital)After a PTT is pressed, this control enables the radio to produce an audible indication (tone) for you to begin speaking into the microphone.Medium tone for 25 msReady to Talk Tone Encrypted P25 digitalAfter a PTT is pressed, this control enables the radio to produce an audible indication (tone) for you to begin speaking into the microphone.Medium tone for 25 msPTT Denied PTT not possible. Momentary tone is present:•Receive only•Key not found•PTT button disabled•Emergency button disabled•Emergency not supported for current channelLow tone for 75 ms
67XG-100ADVANCED OPERATIONS4Maximum transmit duration expiresMaximum transmit duration is exceeded.Low tone for 75 msLow Battery Alarm Alarm sounds upon initial detection of low battery and every 30 seconds thereafter. Tone stops upon detection of a battery charging state.Sequence of tones:•Medium tone for 50 ms•Silence for 60 ms•High tone for 50 msEmergency Call ReceivedRadio is receiving an emergency call or priority call.Low tone for 250 ms and High tone for 250 msTable 1. Alert TonesTone Description Sound/Duration
68XG-100ADVANCED OPERATI ONS4Display Settings1. Enter Settings Menu.2. Use   to highlight and select DISPLAY SETTINGS.
69XG-100ADVANCED OPERATIONS43. Use   to change settings as desired:•FRONT BACKLIGHT - Turn front display backlight on, off, or momentary.•FRONT BRIGHTNESS - Set brightness level of front display. A level of 0 does not turn off front display.•TOP ORIENTATION - Set orientation of top display to be viewed from radio FRONT, BACK or AUTO.When AUTO is used, the XG-100P changes top display to be viewed from back if an external microphone or speaker is attached. Otherwise, the display can be viewed from the front.•TOP BRIGHTNESS - Set brightness level of top display. A level of 0 turns off top display and indicator (TX/RX) LED.4. Use   to exit menu.
70XG-100ADVANCED OPERATI ONS4GPS Settings1. Enter Settings Menu.2. Use   to highlight and select GPS SETTINGS. 3. Use   to change settings as desired:•GPS - Enable or disable internal GPS.•LINEAR UNITS - Set unit of measurement of displayed linear units: STATUTE, METRIC, or NAUTICAL.•ANGULAR UNITS - Set unit of measurement of displayed linear units: CARDINAL, DEGREES, or MILS.•POSITION FORMAT- Set format of displayed position information: Latitude/Longitude Degrees Minutes Seconds (LAT/LONG DMS), LAT/LONG DM, or Universal Transverse Mercator (UTM).
71XG-100ADVANCED OPERATIONS4BluetoothBluetooth settings only appear if enabled in the CPA.4. Use   to exit menu. 1. Enter Settings Menu.2. Use   to highlight and select BLUETOOTH. 3. Use  to set ENABLED to YES. 4. Use   to select PAIRING MGMT. This is used to pair the radio with another bluetooth device.
72XG-100ADVANCED OPERATI ONS45. Make sure device being paired is powered on and set to pair with the XG-100P.If no devices are found and bluetooth is enabled, ADD NEW appears in the lower right corner. Otherwise, OPTIONS appears.6. Use  to ADD NEW or OPTIONS.If OPTIONS was selected, the options menu appears.7. Use   to highlight and select ADD NEW.Device being paired should be displayed.8. Use  to REFRESH device list if device does not appear.9. Use   to highlight and select device.
73XG-100ADVANCED OPERATIONS4For Bluetooth® 2.0 devices, a passkey screen appears.10. Enter unit ID.11. Use   to select OK. For Bluetooth® 2.1 devices, an accept/deny screen appears.12. Use   to select ACCEPT. Progress is then displayed.A message appears when pairing is complete.13. Use   to select OK.
74XG-100ADVANCED OPERATI ONS4Paired device is then displayed under pair devices list.14. Use   to select OPTIONS.15. Use   to highlight and select choices.If INFO was selected, the paired device information screen appears.16. Use   to exit menu.
75XG-100ADVANCED OPERATIONS417. Use   to highlight and select FRIENDLY NAME. This is the name of device being paired. The friendly name used by the CPA will overwrite this setting.18. Enter name for device.19. Use   to select OK.20. Use   to exit menu.
76XG-100ADVANCED OPERATI ONS4Clock SettingsBattery Settings1. Enter Settings Menu.2. Use   to highlight and select CLOCK SETTINGS.3. Use   to change settings as desired:•DISPLAY TIME - Set 12 or 24 hour time display format.•TIME ZONE - Set time zone relative to Universal Time Coordinated (UTC).4. Use   to exit menu. 1. Enter Settings Menu.2. Use   to highlight and select BATTERY SETTINGS.
77XG-100ADVANCED OPERATIONS4WARNING: Use only Harris approved batteries. Injury could occur from using incorrect battery.3. Use   to change settings as desired:•LITHIUM ION - For accurate battery indication on front and top displays, if battery attached to rear of radio is a Lithium-ION (Li-ION) type.•NIMH - For accurate indication on front and top displays, if battery attached to rear of radio is a Nickel Metal Hydride (Ni-MH) type.•PRIMARY LITHIUM - For accurate battery indication on front and top displays, if battery attached to rear of radio is clamshell containing disposable AA lithium batteries.
78XG-100ADVANCED OPERATI ONS4SHORTCUT MENUThe shortcut menu provides menus for quickly accessing commonly used functions.•ALKALINE - For accurate battery indication on front and top displays, if battery attached to rear of radio is clamshell containing disposable AA alkaline batteries.4. Use   to exit menu. 1. At main display, use   center button to display the shortcut menu.
79XG-100ADVANCED OPERATIONS42. Use , , , , , or  to select task:•1. START/STOP SCAN - Start or Stop Scan (Shortcut Menu) START SCAN appears if not scanning. STOP SCAN appears if scanning•2. START MONITOR - Monitor and Squelch Types. This is grayed out if radio is scanning.•3. NUISANCE DEL - Nuisance Delete. This is grayed out if not scanning•4. MUTE SPKR - Mute/Unmute Speaker•5. LOCK KEYPAD - Lock Keypad•6. FLIP TOP DISPLAY - Flip Top DisplayYou can also use   to scroll to the task.2ABC5JK L
80XG-100ADVANCED OPERATI ONS4Start or Stop Scan (Shortcut Menu)1. Enter Shortcut Menu.2. To start scan, use  to highlight and select START SCAN.START SCAN and NUISANCE DEL are grayed out in emergency mode. NUISANCE DEL is not grayed out when scanning.3. To stop scan, use  to highlight and select STOP SCAN.
81XG-100ADVANCED OPERATIONS4Monitor and Squelch TypesThe monitor function allows you to temporarily turn off selected squelch to monitor for traffic that may not normally break squelch. Squelch used depends on an analog or digital channel. For analog channels, there is:•Noise squelch - any received signal breaks squelch.•Continuous Tone Coded Squelch (CTCSS) - squelch is selective based on tone code.•Continuous Digital Coded Squelch (CDCSS) - squelch is selective based on tone code.For digital channels, there is:•Monitor squelch - any received digital signal breaks squelch.•Normal squelch - Received Network Access Code (NAC) breaks squelch.•Selective squelch - Received NAC and talkgroup Identification (ID) or unit ID breaks squelch.1. Enter Shortcut Menu.START MONITOR is grayed when radio is scanning.2. Use   to select START MONITOR. 3. Use   to toggle the monitor ON or OFF.
82XG-100ADVANCED OPERATI ONS4Nuisance DeleteYou can temporarily removed currently received channel from scan list. This choice is grayed out if the radio is not scanning.1. Enter Shortcut Menu.2. Use   to select NUISANCE DEL while receiving channel you wish to temporarily remove from scan list.
83XG-100ADVANCED OPERATIONS4Mute/Unmute Speaker You can mute or unmute the front panel speaker.1. Enter Shortcut Menu.2. Use   to select MUTE SPKR if speaker is not muted.3. Use   to select UNMUTE SPKR if speaker is muted.
84XG-100ADVANCED OPERATI ONS4Lock KeypadYou can lock the keypad to prevent accidental operations from incorrect keypad press.1. Enter Shortcut Menu.2. Use   to select LOCK KEYPAD. 3. Use   to unlock keypad. Make sure exact sequence of ◄,►, ▼, and ▲ are used. There must be no more than three seconds between key presses.Power cycling radio will not unlock the radio.
85XG-100ADVANCED OPERATIONS4Flip Top DisplayThe top display can be flipped to suit your viewing direction.SET UP SCANThese procedures are used to set up the scan list, home channels, and priority channels. Refer to Start Scan.1. Enter Shortcut Menu.2. Use   to select FLIP TOP DISPLAY. Top display toggles between front and rear display orientation.1. At main display, use   for main menu.2. Use   to highlight and select SCAN or just press .1345798262ABC
86XG-100ADVANCED OPERATI ONS4Zone Scan vs Custom ScanA zone scan list consists of all channels in a zone. The zone scan list is automatically created while generating a mission plan with the Communications Planning Application (CPA). A custom scan list can be created to include channels from different zones. Both zone and custom scan lists can be modified to include or exclude channels from different zones, except you cannot delete zone scan lists.3. Use  to highlight and select ZONE LISTS or CUSTOM LISTS.4. Proceed to:•Add New Scan List•Edit Scan List•Priority 1 Channel•Rename Scan List•Set or Remove Priority (PRI)•Delete Scan List•Set Active Scan List
87XG-100ADVANCED OPERATIONS4Add New Scan ListOnly a custom scan list can be added under CUSTOM SCAN CFG. 1. Enter Set up Scan.2. Use   to highlight ADD SCAN LIST.The radio holds a maximum of 10 scan lists at one time. ADD SCAN LIST option is removed once 10 scan lists are entered into the radio.3. Use   to highlight new scan list. 4. Use   to select OPTIONS. 5. Use   to highlight and select VIEW/EDIT. 6. Use   to highlight channel. 7. Use   to select OPTIONS.
88XG-100ADVANCED OPERATI ONS48. Use   to highlight EDIT SCAN LIST.9. Use   to select channel or zone.10. Use   to toggle channel selection in scan list.11. Alternatively, use   to select OPTIONS.12. Then use   to select ADD CHAN or DELETE CHAN.13. Use   to exit channel list. 14. Use   to exit scan list. GRAYED OUTIS NOT INSCAN LISTGRAYED OUTIS NOT INSCAN LIST
89XG-100ADVANCED OPERATIONS4Edit Scan ListCustom scan configuration screens are shown here. Zone scan configuration is similar.1. Enter Set up Scan.2. Use   to highlight scan list. 3. Use   to select OPTIONS. 4. Use   to highlight and select VIEW/EDIT. 5. Use   to highlight channel. 6. Use   to select OPTIONS.
90XG-100ADVANCED OPERATI ONS47. Use   to highlight EDIT SCAN LIST.8. Use   to select channel.9. Use   to toggle channel selection in scan list.10. Alternatively, use   to select OPTIONS.11. Then use   to select ADD CHAN or DELETE CHAN.12. Use   to exit channel list. 13. Use   to exit scan list. GRAYED OUTIS NOT INSCAN LISTGRAYED OUTIS NOT INSCAN LIST
91XG-100ADVANCED OPERATIONS4Priority 1 ChannelThe priority 1 channel is the channel that is currently selected using the channel knob on top of the radio.Rename Scan ListYou can rename a newly created or existing scan list. You cannot rename zone scan lists.1. Enter Set up Scan.2. Use   to highlight scan list. 3. Use   to select OPTIONS. 4. Use   to highlight and select RENAME LIST. 5. Use   to select OK.
92XG-100ADVANCED OPERATI ONS46. Use   to backspace (◄) over old name.7. Use keypad to enter text for new name. This uses cellphone style text entry (press 2 several times for A).8. When done, use   to select OK.9. Use   to exit channel list. 10. Use   to exit scan list.
93XG-100ADVANCED OPERATIONS4Set or Remove Priority (PRI)Priority (PRI) channels are scanned more often than non-priority channels. The priority 1 channel is the channel that is currently selected using the channel knob on top of the radio.Custom scan configuration screens are shown here. Zone scan configuration is similar.1. Enter Set up Scan.2. Use   to highlight scan list. 3. Use   to select OPTIONS. 4. Use   to highlight and select VIEW/EDIT. 5. Use   to highlight channel. 6. Use   to select OPTIONS.
94XG-100ADVANCED OPERATI ONS4Delete Scan ListYou cannot delete zone scan lists.7. Use   to highlight and select SET PRI. Priority channel appears with a P2.Priority channel can also be set in the channel list. Scan list is shown here.8. Use   to exit channel list.9. Use   to exit scan list. 1. Enter Set up Scan.2. Use   to highlight custom scan list. 3. Use   to select OPTIONS. 4. Use   to highlight and select DELETE LIST.
95XG-100ADVANCED OPERATIONS4Set Active Scan ListYou can set custom scan list as active using the options menu.5. Use   to exit channel list. 6. Use   to exit scan list. 1. Enter Set up Scan.2. Use   to highlight custom scan list. 3. Use   to select OPTIONS. 4. Use   to highlight and select SET ACTIVE. Icon appears to left of active list.5. Use   to exit channel list.
96XG-100ADVANCED OPERATI ONS4MESSAGE MENU6. Use   to exit scan list. 1. At main display, use   for main menu.2. Use   to highlight and select MESSAGE or just press .3. Observe messages in display.4. Use   to exit back to main screen.1345798268TUV
97XG-100ADVANCED OPERATIONS4UTILITY MENU1. At main display, use   for main menu.2. Use   to highlight and select UTILITY or just press .3. Use   to highlight and select SELF TEST to run a series of internal radio tests.Status screen appears while testing followed by a screen with passed or failed results.4. Use   to view details.134579826
98XG-100ADVANCED OPERATI ONS45. Use   to scroll through the test results.6. Use   to exit screen. 7. Use   to highlight and select RADIO INFO to view radio information such as software and firmware revisions.8. Observe radio information display.9. Use   to exit screen. 10. Use   to highlight and select BATTERY INFO.
99XG-100ADVANCED OPERATIONS411. Observe detailed information for the attached battery.12. Use   to exit screen. 13. Use   to exit main screen.
100XG-100ADVANCED OPERATI ONS4This page intentionally left blank.
Section PageProgramming Via CPA  . . . . . . . . . . . . . . .102Edit Channel . . . . . . . . . . . . . . . . . . . . . . .102PROGRAMMING 5
102XG-100PROGRAMMING5This section provides information on front panel programming. Programming can also be accomplished by creating a plan using a computer.PROGRAMMING VIA CPAThe Communications Planning Application (CPA) is to be used for the bulk of programming the XG-100P. Use USB cable, 10282-0410-A1.Using the CPA you can fully program the XP-100P, including the programmable button, switches and keys.EDIT CHANNELChannels can be edited from the Channel Information (CH INFO) menu display, if enabled using the CPA. Many of the displayed parameters can be modified here. Parameters change, depending on the channel being a digital, analog or dual channel. For receive, a dual channel allows you to receive both digital or analog signals. When transmitting on a dual channel, you can only transmit either a digital or analog signal, depending on how the channel is programmed.1. At main display, use   for channel information menu.2. Use  to scroll through the programmed channel settings.
103XG-100PROGRAM M ING53. Additional settings can be found by scrolling down.CAUTION: Only authorized users should attempt channel editing.If the active mission plan has been programmed to allow channel editing by a properly trained operator, you will be able to use the steps that follow.4. Use to select EDIT CHAN.Password protection is automatically enabled by default when the mission plan is programmed to allow channel editing.5. Enter the password programmed into the plan.NOTE: Password remains active until power cycle.6. Use to select OK.
104XG-100PROGRAMMING57. Use  to highlight and select RX FREQUENCY.8. Enter new receive frequency.9. Use   to select OK.10. Use   to cancel.11. For digital channel, modify remaining channel settings:•TX FREQUENCY - Transmit frequency.•TALKGROUP - Talkgroup name cannot be set here.•RX NAC - Network Access Code (NAC) radio uses for selective squelch in receive.•TX NAC - NAC radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).DIGITAL CHANNEL SHOWN
105XG-100PROGRAM M ING512. For analog channel, modify remaining channel settings:•TX FREQUENCY - Transmit frequency.•RX SQUELCH - Squelch type radio uses in receive.•RX TONE - Tone radio uses to break selective squelch on receiving radio (Monitor and Squelch Types).•RX CODE - Code radio uses to break selective squelch on receiving radio (Monitor and Squelch Types).•TX SQUELCH - Squelch type radio uses in transmit.•TX TONE - Tone radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).•TX CODE - Code radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).Channels configured with TX SQUELCH type of CDCSS A or CDCSS B use RXCODE and TXCODE.Channels configured with TX SQUELCH type of CTCSS use RXTONE and TXTONE.ANALOG CHANNEL SHOWN
106XG-100PROGRAMMING513. For dual channel, modify remaining channel settings:•TX FREQUENCY - Transmit frequency.•TALKGROUP - Talkgroup name cannot be set here.•RX NAC - NAC radio uses for selective squelch in receive.•RX SQUELCH - Squelch type radio uses in receive.•RXTONE - Tone radio uses to break selective squelch on receiving radio (Monitor and Squelch Types).•RX CODE - Code radio uses to break selective squelch on receiving radio (Monitor and Squelch Types).•TX NAC - NAC radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).•TX SQUELCH - Squelch type radio uses in transmit.DUAL CHANNEL SHOWN
107XG-100PROGRAM M ING5•TXTONE - Tone radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).•TX CODE - Code radio transmits to break selective squelch on receiving radio (Monitor and Squelch Types).Channels configured with TX SQUELCH type of CDCSS A or CDCSS B use RXCODE and TXCODE.Channels configured with TX SQUELCH type of CTCSS use RXTONE and TXTONE.14. Use   to exit menu.15. Use   to exit menu.NEWCHANNELSETTINGS
108XG-100PROGRAMMING5PROGRAMMABLE HOT KEY AND BUTTONSThe programmable hot key and buttons shown in XG-100P Controls are programmed using the CPA. You can program hot key and buttons for the following:•Backlight Toggle - Off, On, Momentary•Scan•Flip Top Display•Lock Keypad•Monitor•Nuisance Delete•Talkaround Mode•Speaker Mute•Next Zone Up•Next Zone Down
Section PageMarine Frequencies . . . . . . . . . . . . . 110Accessories . . . . . . . . . . . . . . . . . . . 123REFERENCE 7
110XG-100REFERENCE7MARINE FREQUENCIESRefer to Table 2 for a list of maritime frequencies per United States Coast Guard (USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department Fisheries and Oceans, August 2009:•United States (US)•International (Intl)•Canada (CA)Table 2. Marine FrequenciesChannel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)1 1 T: 156.05R: 160.65T: 160.65R: 156.05International: Public Correspondence, Port Operations1a T/R: 156.05 T/R: 156.05 US: Port Operations and Commercial, Vessel Traffic Service (VTS). New Orleans/Lower Mississippi area. 2 2 T: 156.10R: 160.70T: 160.70 R: 156.10International: Public Correspondence, Port Operations3 3 T: 156.15R: 160.75T: 160.75R: 156.15International: Public Correspondence, Port Operations4 T: 156.20 R: 160.80T: 160.80 R: 156.20International: Public Correspondence, Port Operations4a T/R: 156.20 T/R: 156.20 Canada: Department Fisheries Ocean (DFO)/Canadian Coast Guard only in British Columbia coast area. Commercial fishing in east coast area5 T: 156.25 R: 160.85T: 160.85 R: 156.25International: Public Correspondence, Port Operations
111XG-100REFERENCE75a 5a T/R: 156.25 T/R: 156.25 US: Port Operations or VTS in Houston, New Orleans and Seattle areas.6 6 6 T/R: 156.30 T/R: 156.30 US: Intership SafetyInternational: IntershipCanada: May be used for search and rescue communications between ships and aircraft.7 T: 156.35 R: 160.95T: 160.95 R: 156.35International: Public Correspondence, Port Operations7a 7a T/R: 156.35 T/R: 156.35 US: Commercial8 8 8 T/R: 156.40 T/R: 156.40 US: Commercial (Intership only)International: IntershipCanada: Also assigned for intership in the Lake Winnipeg area.9 9 9 T/R: 156.45 T/R: 156.45 US: Boater Calling. Commercial and Non-Commercial.International: Intership, Port OperationsCanada: Commercial - British Columbia coast area.May be used to communicate with aircraft and helicopters in predominantly maritime support operations.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
112XG-100REFERENCE710 10 10 T/R: 156.50 T/R: 156.50 US: Commercial International: Intership, Port OperationsCanada: Commercial - British Columbia coast area.May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations.11 11 11 T/R: 156.55 T/R: 156.55 US: Commercial. VTS in selected areas. International: Port OperationsCanada: VTS - British Columbia coast area.Also used for pilotage purposes.12 12 12 T/R: 156.60 T/R: 156.60 US: Port Operations. VTS in selected areas. International: Port OperationsCanada: VTS - British Columbia coast area.Also used for pilotage purposes.13 13 13 T/R: 156.65 T/R: 156.65 US: Intership Navigation Safety (Bridge-to-bridge). Ships >20m length maintain a listening watch on this channel in US waters. International: Intership, Port OperationsCanada: VTS - British Columbia coast area.Also used for pilotage purposes.14 14 14 T/R: 156.70 T/R: 156.70 US: Port Operations. VTS in selected areas. International: Port OperationsCanada: VTS - British Columbia coast area.Also used for pilotage purposes.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
113XG-100REFERENCE715 15 15 T/R: 156.75 T/R: 156.75 US: Environmental (Receive only). Used by Class C Emergency Position-Indicating Radio Beacons (EPIRBs). International: Intership, Port OperationsCanada: Port operations and Ship Movement - British Columbia coast area.All operations limited to 1-watt maximum power. May also be used for on-board communications.16 16 16 T/R: 156.80 T/R: 156.80 US: International Distress, Safety and Calling. Ships required to carry radio, US Coast Guard (USCG), and most coast stations maintain a listening watch on this channel.International: International Distress, Safety and CallingCanada: International Distress, Safety and Calling17 17 17 T/R: 156.85 T/R: 156.85 US: State Control International: Intership, Port OperationsCanada: Port operations and Ship Movement - British Columbia coast area.All operations limited to 1 watt maximum power. May also be used for on-board communications.18 T: 156.90 R: 161.50T: 161.50 R: 156.90International: Public Correspondence, Port Operations18a 18a T/R: 156.90 T/R: 156.90 US: Commercial Canada: Towing - British Columbia coast area.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
114XG-100REFERENCE719 T: 156.95 R: 161.55*T: 161.55* R: 156.95International: Public Correspondence, Port Operations19a 19a T/R: 156.95 T/R: 156.95 US: Commercial Canada: DFO/Canadian Coast Guard. Pacific Pilots - British Columbia coast area.20 20 20 T: 157.00 R: 161.60T: 161.60 R: 157.00US: Port Operations (Duplex) International: Public Correspondence, Port OperationsCanada: Port operations only with 1 watt maximum power.20a T/R: 157.00 T/R: 157.00 US: Port Operations21 T: 157.05 R: 161.65*T: 161.65* R: 157.05International: Public Correspondence, Port Operations21a 21a T/R: 157.05 T/R: 157.05 US: US Coast Guard onlyCanada: DFO/Canadian Coast Guard only.21b - - T/R: 161.6522 T: 157.10 R: 161.70T: 161.70 R: 157.10International: Public Correspondence, Port Operations22a 22a T/R: 157.10 T/R: 157.10 US: Coast Guard Liaison and Maritime Safety Information Broadcasts. Broadcasts announced on channel 16. Canada: For communications between Canadian Coast Guard and non-Canadian Coast Guard stations only.23 23 T: 157.15 R: 161.75T: 161.75 R: 157.15International: Public Correspondence, Port OperationsTable 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
115XG-100REFERENCE723a T/R: 157.15 T/R: 157.15 US: US Coast Guard only23b - - T/R: 161.75 Canada: Continuous Marine Broadcast (CMB) service.24 24 24 T: 157.20 R: 161.80T: 161.80 R: 157.20US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations25 25 25 T: 157.25 R: 161.85T: 161.85 R: 157.25US: Public Correspondence (Marine Operator) International: Public Correspondence, Port OperationsCanada: Also assigned for operations in the Lake Winnipeg area.25b T/R: 161.8526 26 26 T: 157.30 R: 161.90T: 161.90R: 157.30US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations27 27 27 T: 157.35 R: 161.95T: 161.95 R: 157.35US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations28 28 28 T: 157.40R: 162.00T: 162.00R: 157.40US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations28b - - T/R: 162.00 Canada: Continuous Marine Broadcast (CMB) service.60 60 T: 156.025 R: 160.625T: 160.625 R: 156.025International: Public Correspondence, Port Operations61 T: 156.075 R: 160.675T: 160.675 R: 156.075International: Public Correspondence, Port OperationsTable 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
116XG-100REFERENCE761a 61a T/R: 156.075 T/R: 156.075 Canada: DFO/Canadian Coast Guard only in British Columbia coast area.62 T: 156.125 R: 160.725T: 160.725 R: 156.125International: Public Correspondence, Port Operations62a T/R: 156.125 T/R: 156.125 Canada: DFO/Canadian Coast Guard only in British Columbia coast area.63 T: 156.175 R: 160.775T: 160.775 R: 156.175International: Public Correspondence, Port Operations63a 63a T/R: 156.175 T/R: 156.175 US: Port Operations and Commercial, VTS. New Orleans/Lower Mississippi area. Canada: Tow Boats - British Columbia coast area.64 64 T: 156.225 R: 160.825T: 160.825R: 156.225International: Public Correspondence, Port Operations64a 64a T/R: 156.225 T/R: 156.225 Canada: Commercial fishing only.65 T: 156.275 R: 160.875T: 160.875R: 156.225International: Public Correspondence, Port OperationsTable 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
117XG-100REFERENCE765a 65a T/R: 156.275 T/R: 156.275 US: Port Operations Canada: Search and rescue and antipollution operations on the Great Lakes. Towing on the Pacific Coast. Port operations only in the St. Lawrence River areas with 1 watt maximum power. Intership in inland Manitoba, Saskatchewan, and Alberta areas.66 T: 156.325 R: 160.925T: 160.925 R: 156.325International: Public Correspondence, Port Operations66a 66a T/R: 156.325 T/R: 156.325 US: Port Operations Canada: Port operations only in the St. Lawrence River/Great Lakes areas with 1 watt maximum power. 1 watt marina channel - British Columbia coast area.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
118XG-100REFERENCE767 67 67 T/R: 156.375 T/R: 156.375 US: Commercial. Used for Bridge-to-bridge communications in lower Miss. River. Intership only. International: Intership, Port OperationsCanada: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. Commercial fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta areas. Pleasure craft - British Columbia coast area.68 68 68 T/R: 156.425 T/R: 156.425 US: Non-Commercial International: Port OperationsCanada: For marinas, yacht clubs and pleasure craft.69 69 69 T/R: 156.475 T/R: 156.475 US: Non-Commercial International: Intership, Port OperationsCanada: Commercial fishing only - east coast area.Pleasure craft - British Columbia coast area.70 70 70 T/R: 156.525 T/R: 156.525 US: Digital Selective Calling (voice communications not allowed) International: Digital selective calling for distress, safety and callingCanada: Digital selective calling for distress, safety and calling71 71 71 T/R: 156.575 T/R: 156.575 US: Non-CommercialInternational: Port OperationsCanada: Ship Movement - British Columbia coast area.Marinas and yacht clubs - east coast and on Lake Winnipeg.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
119XG-100REFERENCE772 72 72 T/R: 156.625 T/R: 156.625 US: Non-Commercial (Intership only) International: IntershipCanada: May be used to communicate with aircraft and helicopters in predominantly maritime support operations.Pleasure craft - British Columbia coast area73 73 73 T/R: 156.675 T/R: 156.675 US: Port OperationsInternational: Intership, Port OperationsCanada: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. Commercial fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta areas.74 74 74 T/R: 156.725 T/R: 156.725 US: Port OperationsInternational: Port OperationsCanada: VTS and Ship Movement British Columbia coast area.75 75 75 T/R: 156.775 T/R: 156.775 International: Port OperationsCanada: Simplex port operation, ship movement and navigation related communication only.1 watt maximum.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
120XG-100REFERENCE776 76 76 T/R: 156.825 T/R: 156.825 International: Port OperationsCanada: Simplex port operation, ship movement and navigation related communication only.1 watt maximum.77 77 77 T/R: 156.875 T/R: 156.875 US: Port Operations (Intership only)International: IntershipCanada: Pilotage - British Columbia coast area; 25 watts. Port operations only in the St. Lawrence River/Great Lakes areas with 1 watt maximum power.78 T: 156.925 R: 161.525T: 161.525 R: 156.925International: Public Correspondence, Port Operations78a 78a T/R: 156.925 T/R: 156.925 US: Non-CommercialCanada: Fishing Industry - British Columbia coast area.79 T: 156.975 R: 161.575T: 161.575R: 156.975International: Public Correspondence, Port Operations79a 79a T/R: 156.975 T/R: 156.975 US: Commercial. Non-Commercial in Great Lakes onlyCanada: Fishing Industry - British Columbia coast area.80 T: 157.025 R: 161.625T: 161.625 R: 157.025International: Public Correspondence, Port Operations80a 80a T/R: 157.025 T/R: 157.025 US: Commercial. Non-Commercial in Great Lakes onlyCanada: Fishing Industry - British Columbia coast area.81 T: 157.075 R: 161.675T: 161.675 R: 157.075International: Public Correspondence, Port OperationsTable 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
121XG-100REFERENCE781a 81a T/R: 157.075 T/R: 157.075 US: US Government only - Environmental protection operationsCanada: DFO/Canadian Coast Guard use only.82 T: 157.125 R: 161.725T: 161.725 R: 157.125International: Public Correspondence, Port Operations82a 82a T/R: 157.125 T/R: 157.125 US: US. Government onlyCanada: DFO/Canadian Coast Guard use only.83 T: 157.175 R: 161.775T: 161.775R: 157.175International: Public Correspondence, Port Operations83a 83a T/R: 157.175 T/R: 157.175 US: US Coast Guard onlyCanada: DFO/Canadian Coast Guard and other Government agencies.83b - - T/R: 161.77584 84 84 T: 157.225 R: 161.825T: 161.825 R: 157.225US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations85 85 85 T: 157.275R: 161.875T: 161.875 R: 157.275US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations86 86 86 T: 157.325 R: 161.925T: 161.925R: 157.325US: Public Correspondence (Marine Operator) International: Public Correspondence, Port Operations87 87 87 T: 157.375 R: 161.975T: 161.975R: 157.375US: Automatic Identification System duplex repeaterInternational: Port OperationsCanada: Port operation and ship movement - east coast area.Pleasure craft - British Columbia coast area.Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
122XG-100REFERENCE787a T/R: 157.375 T/R: 157.375 US: Public Correspondence (Marine Operator) 87b T/R: 161.975 T/R: 161.975 Canada: Automatic Ship Identification and Surveillance System.88 88 T: 157.425 R: 162.025T: 162.025R: 157.425US: Commercial, Intership only. International: Port OperationsCanada: Port operation and ship movement - British Columbia coast area.88a T/R: 157.425 T/R: 157.425 US: Commercial, Intership only. Canada: Automatic Ship Identification and Surveillance System.88b T/R: 162.025 T/R: 162.025WX1WX1R: 162.55WX2WX2R: 162.4WX3WX3R: 162.475WX4R: 162.425WX5R: 162.45WX6R: 162.5WX7R: 162.525Table 2. Marine Frequencies (Continued)Channel FrequencyChannel UsageUS Intl CA Ship (MHz) Shore (MHz)
123XG-100REFERENCE7ACCESSORIESOnly use Harris approved accessories. Contact Harris for requirements not contained in this list:Standard Remote Speaker Microphone (RSM) - Rugged, submersible, 6 ft. (stretch length) coil cord, swivel clip, 3.5 mm earpiece interface, high/low volume control1-Bay Charger - Multi-chemistry battery charger, supports radio operation while charging6-Bay Charger - Multi-chemistry, multi-bay battery charge, 12 VDCLeather Carry Cases - Durable radio carry-cases selectable with swivel D-clip belt-loops or T-straps. Various styles available.Nylon Carry Cases - Nylon radio carry cases available in various styles and configurations.USB Cable - USB computer interface cable for use with the RF-6650P Communications Planning ApplicationKVL Cable - Adapter cable supports loading encryption keys with the Motorola KVL 3000 PlusAA Clamshell - Battery pack for use with AA-sized batteriesLithium Battery - Rechargeable Lithium-ION (Li-ION) battery pack (120882-0308-01)Antenna - Full-Spectrum, 136-870 MHz frequency coverage
124XG-100REFERENCE7This page intentionally left blank.
GLOSSARY G
126XG-100GLOSSARYG-A-AES Advanced Encryption StandardAES-256 Advanced Encryption Standard, 256-bitAMBE+2 Advanced Multi-Band Excitationimplementation 2 ANSI American National Standards Institute-B--C-CCelsiusCA CanadaCDCSS Continuous Digital Coded Squelch SystemCH INFO Channel InformationCKR Common Key ReferencesCMB Continuous Marine BroadcastCPA Communications Planning ApplicationCTCSS Continuous Tone Coded Squelch System-D-DES Digital Encryption StandardDES-OFB Digital Encryption Standard Output FeedbackDFO Department Fisheries Ocean-E-EPIRB Emergency Position-Indicating Radio Beacons-F-FFahrenheitFCC Federal Communications CommissionFM Frequency Modulation-G-GHz Giga (109) HertzGPS Global Positioning System-H-
127XG-100GLOSSARYG-I-ID IdentificationIEEE Institute of Electrical & Electronics EngineersINTL International-J--K-kHz kilo (103) HertzKID Key IdentificationKVL Key Variable Loader (Motorola KVL 3000 Plus)-L-LAT/LONG DMS Latitude/Longitude Degrees Minutes SecondsLED Light Emitting DiodeLi-ION Lithium-ION-M-MHz Megahertzmm Millimeterms milli (10-3) seconds-N-NAC Network Access CodeNi-MH Nickel Metal HydrideNOAA National Oceanic and Atmospheric Administration-O-OET Office of Engineering and Technology-P-P25 Project 25POS PositionPRI Priority (Channel)PTT Push-to-Talk-Q-
128XG-100GLOSSARYG-R-RSM Remote Speaker MicrophoneRX Receive-S-SMA Subminiature version A-T-TIA Telecommunications Industry AssociationTX Transmit-U-UHF Ultra High FrequencyUS United StatesUSCG United States Coast GuardUTC Universal Time CoordinatedUTM Universal Transverse Mercator -V-VDC Volts, Direct CurrentVHF Very High FrequencyVTS Vessel Traffic Service-W-WEEE Waste from Electric and Electronic Equipment-X--Y--Z-
INDEX-129XG-100INDEXISymbols(PRI), Set or Remove Priority ....... 93(Shortcut Menu), Start or Stop Scan 80Numerics1 Channel, Priority ...................... 913000 Plus, Create Key in the KVL .463000 Plus, Create Keygroup in the KVL ................................ 473000 Plus, Zeroize All from KVL ... 573000 Plus, Zeroize Keygroups Using KVL ............................ 553000 Plus, Zeroize Keys Using KVL ..................................... 53AAccessories ............................... 123Activate/View Mission Plan .......... 58Active Scan List, Set ................... 95Add New Scan List ..................... 87Advanced Operations ................. 45All from KVL 3000 Plus, Zeroize ... 57All from Radio, Zeroize ................ 52Assemble the Radio .................... 14Audio Settings ........................... 64BBank, Select Channel ................. 24Basic Operations ........................ 17Basic Setup ............................... 13Battery Settings .......................... 76Battery, Removing the ................. 16Before First Time Use ................. 23Belt Clip, Removing Optional ........ 16Bluetooth .................................. 71Buttons, Programmable Hot Key and ............................... 108Bypass Repeater, Use Talkaround to ........................ 33CCall, Declaring an Emergency ...... 43Call, Make a Priority .................... 30Call, Make an Individual .............. 28Call, Receiving an Emergency ...... 42CH INFO Menu ...........................60Channel Bank, Select ..................24Channel Using Knob, Select ......... 24Channel, Edit .............................102Channel, Priority 1 ...................... 91Clip, Removing Optional Belt ........16Clock Settings ............................76Controls, XG-100P ......................18CPA, Programming Via ................ 102Create Key in the KVL 3000 Plus ..46Create Keygroup in the KVL 3000 Plus .....................................47Create Keys ...............................46Custom Scan, Zone Scan vs ........86DDeclaring an Emergency Call ........43Delete Scan List .........................94Delete, Nuisance ........................38, 82Description, Equipment ................12Display Settings ..........................68Display, Flip Top .........................85Display, Main ..............................21Display, Top ...............................20EEdit Channel ..............................102Edit Scan List .............................89Emergency Call, Declaring an .......43Emergency Call, Receiving an ......42Emergency Operation ..................42Encryption On or Off, Turn ............25Equipment Description .................12FFirst Time Use, Before .................23Flip Top Display .......................... 85Frequencies, Marine ....................110GGlossary ....................................125GPS Information, View .................40GPS Settings ............................. 70Guidelines, Storage ..................... 12
XG-100INDEXINDEX-130IHHot Key and Buttons, Programmable .......................108IIndividual Call, Make an ...............28INFO Menu, CH ..........................60Information, View GPS .................40Introduction ................................11KKey and Buttons, ProgrammableHot .......................................108Key in the KVL 3000 Plus, Create ..46Keygroup in the KVL 3000 Plus, Create ..................................47Keygroups Using KVL 3000 Plus, Zeroize .................................55Keygroups, Load .........................50Keypad, Lock .............................84Keys Using KVL 3000 Plus, Zeroize .................................53Keys, Create ..............................46Keys, Load .................................48Knob, Select Channel Using .........24KVL 3000 Plus, Create Key in the ..46KVL 3000 Plus, Create Keygroup in the ....................................47KVL 3000 Plus, Zeroize All from ....57KVL 3000 Plus, Zeroize Keygroups Using ....................55KVL 3000 Plus, Zeroize Keys Using ....................................53LList, Add New Scan .....................87List, Delete Scan .........................94List, Edit Scan ............................89List, Rename Scan ......................91List, Set Active Scan ....................95Load Keygroups ..........................50Load Keys ..................................48Lock Keypad ..............................84MMain Display ...............................21Make a Priority Call .....................30Make an Individual Call ................28Marine Frequencies .....................110Menu Navigation .........................22Menu, CH INFO ..........................60Menu, Message ..........................96Menu, Settings ............................62Menu, Shortcut ...........................78Menu, Utility ...............................97Menu), Start or Stop Scan (Shortcut ...............................80Menus, Select Zone Using ............26Message Menu ...........................96Mission Plan, Activate/View ..........58Monitor and Squelch Types ..........81Mute/Unmute Speaker .................83NNavigation, Menu ........................22New Scan List, Add .....................87New Talkgroup, Select a ...............31Nuisance Delete .........................38, 82OOff, Turn Encryption On or ............25Operation, Emergency .................42Operations, Advanced .................45Operations, Basic ........................17Optional Belt Clip, Removing ........16or Off, Turn Encryption On ............25or Remove Priority (PRI), Set ........93or Stop Scan (Shortcut Menu), Start .....................................80PPlan, Activate/View Mission ..........58Plus, Create Key in the KVL 3000 ..46Plus, Create Keygroup in the KVL 3000 .....................................47Plus, Zeroize All from KVL 3000 ....57Plus, Zeroize Keygroups Using KVL 3000 ..............................55
INDEX-131XG-100INDEXIPlus, Zeroize Keys Using KVL 3000 .................................... 53Power On and Set Volume ........... 23Priority (PRI), Set or Remove ....... 93Priority 1 Channel ....................... 91Priority Call, Make a .................... 30Programmable Hot Key and Buttons ................................ 108Programming ............................. 101Programming Via CPA ................ 102RRadio, Assemble the ................... 14Radio, Zeroize All from ................ 52Receiving an Emergency Call ...... 42Reference ................................. 109Remove Priority (PRI), Set or ....... 93Removing Optional Belt Clip ........ 16Removing the Battery ................. 16Rename Scan List ...................... 91Repeater, Use Talkaround to Bypass ................................. 33SScan (Shortcut Menu), Start or Stop .................................... 80Scan List, Add New .................... 87Scan List, Delete ........................ 94Scan List, Edit ............................ 89Scan List, Rename ..................... 91Scan List, Set Active ................... 95Scan vs Custom Scan, Zone ........ 86Scan, Set up .............................. 85Scan, Start ................................ 35Scan, Stop ................................ 37Scan, Zone Scan vs Custom ........ 86Select a New Talkgroup ............... 31Select Channel Bank .................. 24Select Channel Using Knob ......... 24Select Zone Using Menus ............ 26Set Active Scan List .................... 95Set or Remove Priority (PRI) ........ 93Set up Scan ............................... 85Set Volume, Power On and .......... 23Settings Menu ............................62Settings, Audio ...........................64Settings, Battery .........................76Settings, Clock ...........................76Settings, Display .........................68Settings, GPS .............................70Setup, Basic ...............................13Shortcut Menu ............................ 78Speaker, Mute/Unmute ................83Squelch Types, Monitor and .........81Start or Stop Scan (Shortcut Menu) ..................................80Start Scan ..................................35Stop Scan ..................................37Stop Scan (Shortcut Menu), Start or ................................. 80Storage Guidelines ......................12TTalkaround to Bypass Repeater, Use ......................................33Talkgroup, Select a New ..............31Time Use, Before First .................23Top Display ................................20Top Display, Flip .........................85Turn Encryption On or Off ............25Types, Monitor and Squelch ......... 81Uup Scan, Set ..............................85Use Talkaround to Bypass Repeater ..............................33Use, Before First Time .................23Using Knob, Select Channel ......... 24Using KVL 3000 Plus, Zeroize Keygroups ............................55Using KVL 3000 Plus, Zeroize Keys ....................................53Using Menus, Select Zone ...........26Utility Menu ................................97VVia CPA, Programming ................102View GPS Information .................40Volume, Power On and Set ..........23
XG-100INDEXINDEX-132Ivs Custom Scan, Zone Scan .........86XXG-100P Controls .......................18ZZeroize All from KVL 3000 Plus .....57Zeroize All from Radio .................52Zeroize Keygroups Using KVL 3000 Plus ..............................55Zeroize Keys Using KVL 3000 Plus 53Zone Scan vs Custom Scan .........86Zone Using Menus, Select ............26
Ra. Harris Corporation, a Delaware Corporation, through its RF Communications Division (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer") that Equipment manufactured by or for the Seller shall be free from defects in material and workmanship, and shall conform to its published specifications. With respect to all non-Seller Equipment, Seller gives no warranty, and only the warranty, if any, given by the manufacturer shall apply.  Rechargeable batteries are excluded from this warranty but are warranted under a separate Rechargeable Battery Warranty (ECR-7048).b. Seller's obligations set forth in Paragraph C below shall apply only to failures to meet the above warranties occurring within the following periods of time from date of sale to the Buyer and are conditioned on Buyer's giving written notice to Seller within thirty (30) days of such occurrence:1. For fuses and non-rechargeable batteries, operable on arrival only.2. For parts and accessories (except as noted in B.1) sold by Seller's Service Parts Operation, ninety (90) days.3. For P7300, P7200, P7100IP, P5400, P5300, P5200, P5100, P3300, M7300, M7200 (including V-TAC), M7100 IP, M5300 and M3300 radios, two (2) years, effective 10/01/2007.4. For UnityTM XG-100P, three (3) years.5. For all other equipment of Seller's manufacture, one (1) year.c. If any Equipment fails to meet the foregoing warranties, Seller shall correct the failure at its option (i) by repairing any defective or damaged part or parts thereof, (ii) by making available at Seller's factory any necessary repaired or replacement parts, or (iii) by replacing the failed Equipment with equivalent new or refurbished Equipment. Any repaired or replacement part furnished hereunder shall be warranted for the remainder of the warranty period of the Equipment in which it is installed. Where such failure cannot be corrected by Seller's reasonable efforts, the parties will negotiate an equitable adjustment in price. Labor to perform warranty service will be provided at no charge during the warranty period only for the Equipment covered under Paragraph B.3 and B.4. To be eligible for no-charge labor, service must be performed at Seller's factory, by an Authorized Service Center (ASC) or other Servicer approved for these purposes either at its place of business during normal business hours, for mobile or personal equipment, or at the Buyer's location, for fixed location equipment. Service on fixed location equipment more than thirty (30) miles from the Service Center or other approved Servicer's place of business will include a charge for transportation.d. Seller's obligations under Paragraph C shall not apply to any Equipment, or part thereof, which (i) has been modified or otherwise altered other than pursuant to Seller's written instructions or written approval or, (ii) is normally consumed in operation or, (iii) has a normal life inherently shorter than the warranty periods specified in Paragraph B, or (iv) is not properly stored,
installed, used, maintained or repaired, or, (v) has been subjected to any other kind of misuse or detrimental exposure, or has been involved in an accident.e. The preceding paragraphs set forth the exclusive remedies for claims based upon defects in or nonconformity of the Equipment, whether the claim is in contract, warranty, tort (including negligence), strict liability or otherwise, and however instituted. Upon the expiration of the warranty period, all such liability shall terminate. The foregoing warranties are exclusive and in lieu of all other warranties, whether oral, written, expressed, implied or statutory. NO IMPLIED OR STATUTORY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY. IN NO EVENT SHALL THE SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARY DAMAGES.This warranty applies only within the United States.Harris Corporation Harris CorporationRF Communications Division RF Communications Division221 Jefferson Ridge Parkway 1680 University AvenueLynchburg, VA 24501 Rochester, NY 146101-800-528-7711 1-585-244-5830
RF Communications Division 1680 University Ave Rochester, NY USA 14610Tel: 585-244-5830. Fax: 585-242-4755 www.harris.com││

Navigation menu