Harsper HP-420M PDP Monitor User Manual 0416 Maple NTSC Eng

Harsper Co., Ltd. PDP Monitor 0416 Maple NTSC Eng

Contents

User Manual 3 of 3

Monitor Installation
23
OWNER'S MANUAL
50" Speaker (Optional) Installion
• Match red to red, black to black of Speaker / TV.
• Always lift the monitor itself (not the speakers) when handling or moving the monitor after speakers have been installed.
Assemble the monitor to speaker with using the supporter hanger and bolt. As shown above A, assemble the a and b of
supporter hanger to the monitor with using the bolt(M4x8). Assemble the c, d and e to the speaker with using the
bolt(4x16). If the bolts are tightened too much, the product could be damaged.
Monitor Installation
24 OWNER'S MANUAL
Connecting Speakers to the Monitor using the speakers wires provided
2-Supporter Hanger
(Mount speakers to Monitor)
6-4 X 16 Bolts
(Attach Supporter Hanger to speakers)
8-M4 X 8 Bolts
(Attach Supporter Hanger to monitor)
2-Speaker Wires 2-Speaker Wire Holders
(for arranging the speaker wires)
Accessories
R
L
• Be sure monitor power is turned off before making any connections. Place the speakers in the position you want. Install
the speaker wires on the monitor and speaker. Be sure to connect the positive "+" wire to the "+" input and the negative
"-" wire to the "-" input. Connect left monitor input to left speaker and right monitor input to right speaker. Any extra
speaker wire length remaining can be bunched into the wire holders provided. (Caution: Once installed, the speaker wire
holders lock into position and can't be removed.)
Optional Extras
25
OWNER'S MANUAL
Table Stand
(Type United)
Table Stand
(Type Separated)
Fixed Wall Mount Bracket Side Mount Speaker
Watching TV
26 OWNER'S MANUAL
1
2
3
4
Connect the Antenna or CATV signal source to TV input. Press TV/VIDEO button on the Remote Control
and select TV on OSD.
Use CH+, CH- button or numeric button to change TV channel for your channel selection.
You can watch the previous channel by pressing PRE CH. Button on Remote Control.
Also, you can tune to cable service provided channels using the cable box. For further information
regarding cable TV service, contact cable TV service provider(s).
To watch TV (When the Interface board is installed.)
Watching VCR
27
OWNER'S MANUAL
Press TV/ Video button on the Remote Control and select Video Sources. (When connection with S-Video,
select the S-Video.)
Insert a video tape into the VCR and press the PLAY button on the VCR.
1
2
•No Signal
"No Signal" on display will disappear after 5 minutes, then the TV will go in to Sleep Mode (dark).
< To avoid picture noise (interference), leave an adequate distance (over 3m) between the VCR and monitor. >
When connecting the Plasma Monitor with external equipment, match the colors of connecting ports (Video -
yellow, Audio(L) - white, Audio(R) - red).
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma
Monitor.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting
a regular VCR to the Video input.
Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a
VCR 4:3 picture format or if a CH label is present.
To watch VCR (When the Interface board is installed.)
Watching DVD (Interlace)
28 OWNER'S MANUAL
Connect DVD video inputs to Y, PB, PR of COMPONENT (480i) (DVD INPUT) and audio inputs to Audio
sockets of AV INPUT.
How to connect (When the Interface board is installed.)
Component Input ports
You can get better picture quality if you connect DVD player with component input ports as below.
Video output ports of
DVD player
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
YPBPR
Component ports of the
Monitor
Turn on the DVD player.
Press TV / Video button on the remote control of the monitor to select Component.
1
2
How to use (When the Interface board is installed.)
Watching DVD (Progressive)
29
OWNER'S MANUAL
Turn on the DVD player or Settop Box.
Press TV / Video button on the remote control of the monitor to
select Component. (Select "DTV YPbPr")
1
2
How to use (When the Interface board is installed.)
•Connect normal 480i, DVD source, through normal YPbPr of Componect signal only.
•No Signal
"No Signal" on display will disappear after 5 minutes, then the TV will go in to Sleep Mode (dark).
•Normal DVD source is based on 480i, which should be through normal YPbPr of Component signal.
DVD/HDTV Watching through RGB Input for Progressive(480p, 720p, 1080i)
mode(YPbPr)
Connecting The PC
30 OWNER'S MANUAL
You can enjoy vivid picture and sound with connecting a PC with the Monitor.
Connecting a PC to the PDP
Connect a PC (15pin) cable between the Video Output jack on the PC and the RGB (480p, 720p, 1018i) in
(15p D-SUB) on the PDP.
Pin Configuration
15Pin Signal Cable (based on mate pin)
DVI Cable
To see the PC through DVI, Select
"Digital RGB" in your OSD.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
Pin No. Description
Displayable Monitor Specification
31
OWNER'S MANUAL
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
45.913
53.011
64.062
35.156
37.879
48.077
46.875
53.674
56.000
64.016
49.725
31.468
48.363
56.476
60.023
64.000
48.387
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
90.03
100.04
120.00
56.25
60.31
72.18
75.00
85.06
90.00
100.00
74.55
60.05
60.00
70.06
75.02
60.00
60.00
Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz)
•Synchronization input form : separate
•852 x 480 : 42" Native Resolution
Horizontal Polarity is Positive(+)
Vertical Polarity is Negative(-)
• 1366 x 768 : 50" Native Resolution
Horizontal Polarity is Positive(+)
Vertical Polarity is Negative(-)
•The PDP recognizes 640x480@60Hz signal as
480p DTV signal. (They has almost same
frequencies.) So the signal is expanded, please
try other signals like 640x480@75Hz.
•The PDP operates abnormally if a non-standard video
format is selected.
•Depending on the manufacturer, your PC screen might
appear differently (and depending on your particular
version of Windows).
Check your PC instruction book for information about
connecting your PC to a PDP.
• The PDP may operate abnormally if a non-standard video
signal.
• "Out of range" message box will appear when an
over-spec video signal is input. Change the video settings
of PC when the message is displayed.
640 x 350
640 x 400
640 x 480
800 x 600
832 x 624
852 x 480
1024 x 768
1280 x 1024
1366 x 768
OSD Structure
32 OWNER'S MANUAL
• OSD (On Screen Display) allows user to control or adjust various features and settings in accordance with his/her
preferences.
• Press the MENU/SET button on the Remote Control, you may see the OSD.
e.g.) OSD menu on the video background
PICTURE (TV & VIDEO)
33
OWNER'S MANUAL
Adjust Brightness, Contrast, Color, Hue, Sharpness, Temperature and Recall on OSD menu.
Press MENU/SET button to activate OSD.
Press MENU/SET button again to get into
PICTURE main menu.
BRIGHTNESS
Control the brightness of display by
using left and right button.
CONTRAST
Control the contrast of display.
COLOR
Control the color saturation of display.
HUE
Control the color appearance
from neutral to red or green or Blue.
1
2
Distinct Vague
Dark Bright
Decrease
Red Greenish
Increase
Saturation means the color tone in accordance with the difference of color concentration under red
color criteria.
Hue means that it is a difference of color toward Green or Red color direction.
PICTURE (TV & VIDEO)
34 OWNER'S MANUAL
SHARPNESS
Control the sharpness of image edge.
TEMPERATURE
Select the color temperature of screen
image from Warm, Cool and Normal.
RECALL
Go into PICTURE Menu, and select Recall then press set for all resets.
Warm Cold
•Screen Image retention : Do not display a still image (such as on a videogame or when hooking up a PC to this
Monitor) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as "screen burn". To avoid such image retention, refer to page 37 and 40 of this manual to
reduce the degree of brightness and contrast of this screen when displaying a still image.
Less sharp Sharp
PICTURE (PC)
35
OWNER'S MANUAL
Adjust Brightness, Contrast, Temperature and Geometry on OSD menu.
Press MENU/SET button to activate OSD.
Press MENU/SET button again to get into
PICTURE main menu.
BRIGHTNESS
Control the brightness of display.
CONTRAST
Control the contrast of display.
TEMPERATURE
Select the color temperature of
screen image from Warm,
Cool and Normal.
Temperature control by User
Value for Red, Green and Blue can be adjusted
when you choose User mode using ¥key.
1
2
Distinct Vague
Dark Bright
Warm Cold
PICTURE (PC)
36 OWNER'S MANUAL
GEOMETRY
Press MENU/SET button, you can see below picture.
Move where you want to adjust.
H-POSITION
Centering display image.
After selecting Position menu, you can
move the image using VOL -/+ buttons.
V-POSITION
Centering display image.
After selecting Position menu, you can
move the image using VOL -/+ buttons.
PHASE
Fine tuning of display accuracy on the
screen. Only available when you are in
PC/HD input mode.
H-SIZE
Adjust the horizontal size of display.
Only available when you are in PC/HD
input mode.
Auto Adjust
Automatically adjust picture position and eliminate any image shaking.
Mismatch Match
Mismatch Match
< on Analog RGB mode >
AUTO ADJUST is only available on Analog RGB mode.
SOUND (TV & VIDEO + PC)
37
OWNER'S MANUAL
Adjust the Volume, Balance, Sound Mode and AVC on OSD menu.
Press MENU/SET button to activate OSD.
Use DOWN button to go to SOUND main menu.
Press MENU/SET button again to get into
SOUND main menu.
VOLUME
Control the amount of volume of sound.
Ranges from 0 to 100
BALANCE
Control the left and right sound balance.
SOUND MODE
The sound mode feature allows you to choose
the best appropriate audio environment.
SOUND MODE - EQUALIZER
You can adjust the quality of the sound to
suit your taste on User mode.
AVC (Auto Volume Control)
AVC feature controls the volume level between
two different channels automatically.
1
2
3
MISC (TV & VIDEO + PC)
38 OWNER'S MANUAL
Image scaling, OSD display.
VIDEO SIZE(Aspect Ratio)
You can change the scaling size of video on MISC main menu and VIDEO SIZE sub menu or by pressing
V.SIZE button on Remote Control.
16 : 9
Fill the screen regardless of incoming aspect ratio.
4 : 3
Fit the screen with the same aspect ratio as signal source.
Letter Box
Expand letter box contents to full screen. But you will notify the display quality worse than original mode due
to the loss resolution caused by image expansion. (use only with letter box contents)
Zoom
Zooming more like a classical TV size, which is over-scanned.
OSD SHEET
Select the background pattern of OSD. "Opaque" and "Translucent" can be selected. "Opaque" set the
OSD background as solid color. "Translucent" set the OSD background as half transparent.
Changes the Transparency of
background color of OSD window.
OSD POSITION
Select OSD position among nine preset positions.
Opaque Translucent
Translucent
39
OWNER'S MANUAL
Image scaling, OSD display.
SET ID
If you intend to control more than 2 PDPs via PC, you can assign
ID number to each PDP from 1 to 99 by connecting with RS232C cable.
ADVANCED
You can control the burn protect function.
BURN PROTECT
Burn protection is to avoid displaying the same image
long time. To avoid displaying a static image long time,
image moves horizontally 2~3 pixel per 2 minutes.
The moving is repeated until PDP set be power-off.
(Default Value is "On".)
NATIVE MODE
When you use PDP as PC Monitor, Native Mode display all timing to 852 x 480 mode.
When you off NATIVE MODE, PDP display 640x480 mode except 848 x 480 mode.
•When Native Mode is On, 640x480 resolution change to 852x480 resolution.
MISC (TV & VIDEO + PC)
TIME
40 OWNER'S MANUAL
SLEEP : 30 min
➔
60 min
➔
90 min
➔
180 min
Select your desirable setting time to turn off the TV
automatically. 30 min, 60 min, 90 min, 180 min and
"Off" can be selected. The timer will start to count
down just after you select.
TIME SET
You can select the one among Off, Everyday and
Once by using Up and Down button.
TV SET-UP
41
OWNER'S MANUAL
MODE
Select "Air" or "Cable". If your TV set is connected antenna, select "AIR", If you TV set is connected to
the CABLE TV, select "CABLE"
AUTO CHANNEL
If you select "AUTO CHANNEL" , TV set will automatically scan available channel and add to permanent
channel list. If you want to "exit" auto channel scan, press exit key on IR Remote Control.
FINE TUNE
You can manually adjust the tuning precision by using this function.
MTS
Select the audio mode on TV broadcasting. "AUTO", "STEREO", "MONO", "L1" and "L2" can be selected.
If you select "AUTO", the "TV" set will select stereo mode if the channel broadcast in stereo mode, mono
mode otherwise. If you want to set sound mode as "MONO", the set will sounds as mono mode even if the
channel broadcasts with stereo mode. If the channel is broadcasting in Bi-lingual mode and if you want to
listen to secondary language, you should select "L2". The TV set will sounds with default language otherwise.
PIP (PC)
42 OWNER'S MANUAL
PIP works in Analog RGB, Digital RGB, and RTV YPbPr mode.
PIP(Picture in Picture) ON/OFF
Select ON/OFF the PIP mode.
You can choose ON/OFF mode
using VOL-/+ keys.
PIP SOURCE
Select the PIP video source.
After selecting video source menu,
you can change the source using
VOL-/+ keys.
(TV ➔AV1 ➔AV2 ➔SVIDEO ➔
COMPONENT)
AUDIO SOURCE
Select the audio source. When you select 'PIP' mode, you will hear PIP audio source.
When you select 'Main' mode, you will hear Analog RGB audio source. You can change the source
using VOL-/+ keys.
PIP POSITION
Select PIP position among nine preset positions.
•If you want to watch another source picture with PIP function during watching DVD, PC signal cannot be supported.
TV AV1
PIP
PIP
PIP
PIP
PIP
PIP
PIP
PIP
PIP
Hot Key Function By Remote Control
43
OWNER'S MANUAL
MUTE
To turn off the sound.
TV / VIDEO
Select the signal source from multiple input
source of TV, AV1, AV2, S-Video, Component,
Analog RGB and DTV YPbPr.(480p, 720p,
1080i input)
PIP
Activate PIP function on Analog RGB Mode.
V.SIZE
Change the image size setting, ie; 16:9, 4:3,
etc.
100
Press this button first for cable channels over
100.
PRE CH
Go back to previous TV channel.
STILL
Freeze Frame function, press once again for
reset.
PICTURE
The Picture mode feature allows you to choose
three different modes of picture settings.
CH INFO
You can information regarding the channel that
you select.
MTS
Change sound setting, ie; L1, L2, Mono, etc.
Fit Aspect
CATV 100
CATV3:
Mono
Still
Standard
CATV15
L1
Fill Screen
AM 11:07
Hot Key Function By Remote Control
44 OWNER'S MANUAL
Meu/Set
Activate the OSD window, enter the sub-menu.
CH+/CH-
Change the TV channel o TV mode up or
down.
EXIT
Exit from the currnet OSD menu or sub-menu.
VOL+/VOL-
Change the audio level, increase or decrease
and used for OSD navigation.
SOUND
The sound mode feature allows you to
choose the best appropriate audio
environment. ie. Stereo, Mono, Asp.
SLEEP
TV off time setting, push button for 30 min,
60 min, 90 min and 180 min.
TIME
Set the Time function.
BRIGHT
Press "Bright" button repeatedly to directly
choose one of five different setting modes;
Brightness, Contrast, Color and Sharpness
by pushes.
Refer to next page
CLOSED CAPTION
Push Closed Caption button to activate closed
caption menu. Use arrow control keys to
access 2 channels of Closed Captions and 2
channels of Text.
CH ERASE
Erase the TV channel preset.
CH ADD
Add the TV channel preset.
Flat
AM11:40
BRIGHTNESS
50
Manually
Manually
Hot Key Function By Remote Control
45
OWNER'S MANUAL
V-CHIP
Push V-Chip button to activate V-Chip function menu. Input 4digit password
(factory default password : 0000) And follow the directions.
MPAA RATING
Select the block level.
you can change the ‘SHOW’, ‘BLOCK’
by using VOLUME(¥) keys.
BLOCK CONTENT
(TV GUIDELINE CONTENT)
You can change the ‘SHOW’, ‘BLOCK’
by using VOLUME(¥) keys.
TV GUIDELINE
Select the TV guideline.
you can change the ‘SHOW’, ‘BLOCK’
by using VOLUME(¥) keys.
PASSWORD CHANGE
You can change the password.
(4 characters)
Specification
46 OWNER'S MANUAL
42-inch diagonal screen
Variable 4:3 / 16:9 image aspect ratios (4 modes)
16:9 Panoramic mode
853 x 480 physical pixels
1500:1 contrast ratio
Brightness : Peak 1000 cd/m
PC monitor support up to 1280 x 1024 60hz
181-Program Cable-Ready TV tuner (NTSC)
Advanced multi-window viewing :
Picture-In Picture(PIP) with four selectable window positions on PC mode
Multiple input compatible
Advanced Motion digital processor
Motion-Adaptive Deinterlace Processor
Digital progressive line scaling
3:2 Pull-Down for Film Scan Conversion
Digital 3D comb filter (NTSC)
PAL/ SECAM TV / CATV Tuner Module
Closed Caption decoding (NTSC)
Favorite program programming
Program lock / V-chip (NTSC)
High Definition Component Video inputs : 480 i/p, 720p, 1080i, via VGA adapter
Automatic frequency detection
Selectable color temp. settings : Warm, Cool, User
Miscellaneous
Built-in 7W(RMS) audio amplifier And external two speakers Optional
Audio output Line out (NTSC)
Quiet fan less operation
Front panel lock (via RS-232)
Function and Specification
2
* (NTSC) means only for NTSC model.
42" Plasma TV Display Panel
Specification
47
OWNER'S MANUAL
Accessories
Dimensions : (WxHx D) unit : mm
Weight:
Working Environment
Composite : RCA-pin x 1, Scart type x 1
Component video signal : YPbPr x 1(480i/576i)
S-video : Mini DIN 4-pin x 1
RGB input : D-sub 15-pin x 1(480p/576p, 720p, 1080i))
Audio input : RCA-pin Type(L/R) x 5 : Full support separated audio input
Speaker output : Cinch Conn Type(L/R) x 1(4cinch connectors type)
Audio system : Stereo
Control Ports : RS-232 D-sub 9-pin x1
DVI Input and DVI Cable / Optional
Full function remote control
Table stand / Optional
Side-mount Speakers / Optional
1035 x 635 x 95.3 (Main only)
1035 x 705 x 299 (With stand, without Speaker)
1235 x 705 x 299 (With stand and Speaker)
33kg (Main only)
34.8kg (With stand, without Speaker)
36.8kg (With stand and Speaker)
Power : AC 110 ~ 240V, 50/60Hz
Power Consumption : 380 Watts
Temperature
Operation : 0 c ~ 35 c (32 F ~ 90 F)
Storage : -15 c ~ 60 c (5 F ~ 140 F)
Humidity
Operation : 20 ~ 70%
Storage : 20 ~ 80%
Pressure
Operation : 800 ~ 1114hPa
Storage : 600 ~ 1114hPa
Connectivity:
42" Plasma TV Display Panel
Troubleshooting
48 OWNER'S MANUAL
Before you call a service technician, please scan this list of problems and possible solutions.
It may save you time and money.
No picture & No sound • Check whether the Monitor is turned on.
• Power cord inserted into wall outlet?
• Plug another product's power cord into the wall outlet where the
Monitor's power cord was plugged in.
Picture OK & No sound • Press the VOLUME() button.
• Check the audio input signal.
The remote control doesn't work • Check to see if there is any object between the Plasma Display
and the remote control causing obstruction.
• Check to see if the batteries are installed with the correct
polarities.
No or Poor color or Poor picture • Select Color in the Picture and press VOLUME () button.
• Keep a certain distance between the Monitor and the VCR.
• Activate any function to restore the brightness of the picture.
• Check to see that both the monitor and the source are
plugged in and turned on.
The image is too light or too dark • Adjust the Brightness or Contrast settings.
The image is too large or too small • Adjust the Size settings.
No output from one of the speakers • Adjust Balance in the Sound Menu.
Strange sound form the Monitor • Typical sound due to normal Monitor operation, Monitor is not
faulty.
Problem Quick Action for Possible Solution
49
OWNER'S MANUAL
2-Years Limited Warranty
Warranty Service is only available in the country of original purchase. This is an
important document. Attach your bill of sale to this card and keep it in a safe place.
Your bill of sale is your warranty.
Our warranty remains in effect for one year from the date of the first consumer purchase.
WHO IS PROTECTED BY THIS WARRANTY
Our warranty protects the original owner and all subsequent owners, provided that our product
was purchased from an authorized dealer.
Acopy of the original dated bill of sale must be presented whenever warranty service is required.
WHAT IS COVERED BY THIS WARRANTY
Except as specified below, the warranty covers all defects in material and workmanship. The
following are not covered: damage caused by accident, misuse, abuse, product modification or
neglect; damage occurring during shipment; damage from failure to follow instructions contained
in the instruction manual; damage resulting from the performance of repairs by someone not
authorized by us; damage by natural disaster such as lightening, flood etc.; damage caused by
installation of parts that do not conform to the specification; units used for other than home and
office use; units not used for their intended purpose; any claims based on misrepresentations by
the seller; products sold on an "as-is" or final sales basis; or the cost of installing, removing, or
reinstalling the unit. Our liability is limited to the repair or replacement, at our option, if any
defective product and shall not include incidental or consequential damages. We reserve the
right to replace a discontinued model. Any replacement units or parts may be new or rebuilt.
TO OBTAIN WARRANTY SERVICE
If you require warranty service, please return the product to your dealer.
Warranty Card
50 OWNER'S MANUAL
Memo
51
OWNER'S MANUAL
Memo
52 OWNER'S MANUAL
Memo
Manual Version : HMN 1.0 E

Navigation menu