Hearth and Home Technologies RC200 Remote Control Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1141788
Application ID	33S6IGWgoNKXy/vJm1ZU4w==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	59.52kB (744036 bits)
Date Submitted	2009-07-20 00:00:00
Date Available	2009-07-20 00:00:00
Creation Date	2009-06-23 10:37:09
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2009-07-20 16:26:31
Document Title	User manual
Document Creator	Adobe InDesign CS2 (4.0.5)

RC200
IntelliFire Plus™ Multifunction Remote Control
Installation & Operating Instructions
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modification of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
• Read, understand and follow these instructions for safe
installation and operation.
Introduction
Installation of Remote Control Housing
CAUTION! Risk of Fire! DO NOT install damaged or
modified components. Warranty will be voided if damaged
or modified components are installed.
Kit components: One remote control, two #6 screws, two
wall anchors, one A23 battery and one AUX200 module (if
purchased retail).
1. Remove remote control components from packaging.
2. Remove battery cover from the back of the remote by
sliding it down and install A23 battery.
3. Secure the remote control housing on a flat wall surface using the two screws and wall anchors provided.
See Figure 1.
The RC200 multifunctional wireless wall control with
docking station is designed to control constant pilot feature, flame height, blower speed and to turn your gas
fireplace on and off. The RC200 remote control is only
for use with the Hearth & Home Technologies IntelliFire
Plus™ system (IPI).
Installation Precautions
This control is tested and safe when installed in accordance with this installation manual. Do not install any
components that may be damaged.
Do not modify, disassemble, or substitute any of the components included with this kit. Installation of this unit must
be done by a qualified service technician.
Placement of this remote control may affect performance.
An assessment of the space should be done prior to installation for optimum performance.
Figure 1. Mounting Remote Control Housing
4. Place remote control inside housing. See Figure 2.
Determine Location
Determine the location for the remote control. The selected
location should be in the same space as the gas fireplace
with visual sight of fireplace. The remote control must be
placed within 30 feet of the fireplace.
The RC200 is approved for interior installation and should
always be placed under weather resistant cover when used
in exterior applications.
Figure 2. Remote in Housing
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 • 6/09
5. Close the housing door and press the power button.
The red light illuminates if the batteries were properly
installed. See Figure 3.
Programming the RC200 to the Control Module
CAUTION! Risk of burns! DO NOT program the remote
control to the control module when fireplace is hot.
• Verify the ON/OFF/REMOTE switch is in the REMOTE
position. Control module will beep twice when ready.
See Figure 6.
• Using a small item (such as a paper clip) press and
release the learn button located near the ON/OFF/
REMOTE switch. See Figure 6.
RED LED
• Control module will beep once and LED will blink green
for 10 seconds.
• While the LED is blinking, press the power button on
the remote control. A double beep will come out of the
control module to indicate that it has been programmed
successfully.
Figure 3. Mounting Remote Control Housing
AUX200 Module Installation
• Control Module should be set in the OFF position before
any components are installed.
• Insert the 4 hole harness from the AUX200 module into
the 4 pin plug on the control module. See Figure 4.
AUX200
CABLE
NOTICE: Up to three remote controls can be programmed
into the control module. Simply press a button on the other
remote controls during the 10 second programming process
to add another remote into the system.
To clear memory in the control module, use a small item
(such as a paper clip) to press and release the LEARN
button. Control module will beep once and LED will blink
green for 10 seconds DO NOT press any buttons on the
remote during the ten seconds that the green LED blinks.
The memory will be cleared.
REMOTE POSITION
Figure 4. AUX 200 module installation
Fan Installation
• Insert the 3 prong plug from the fan into the receptacle
located in the AUX200 module. See Figure 5.
• Insert 3 prong plug from AUX200 module into REM/AUX
receptacle of fireplace junction box.
Figure 6. Programming RC200
FAN CORD
Figure 5. Plug Fan into AUX200 Module
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 • 6/09
Function Buttons
Menu
Select
Menu
Select
• Remove battery cover from the back of the remote by
sliding it down. Slide the child lock switch to enable or
disable the child lock feature. See Figure 7.
V the FLAME button to adjust the flame
Press
height. The flame height can be adjusted to 5
different settings: MAX, HIGH, MEDIUM, LOW,
MIN. Flame height will not be adjustable for first
ten seconds when fireplace is turned on. The
system remembers the previous flame height
setting and will automatically adjust to previous
Vsetting after 10 seconds.
Notice: No functions will be usable until child lock feature
is disabled.
Press the FAN button to adjust the fan speed.  
The FAN speed can be adjusted to 4 different
settings: HIGH, MED, LOW and OFF. The fan
has a timer built into the control module. After
the fireplace is turned ON the timer will wait for
7 minutes before turning on the fan. In addition,
the fan will remain on for 12 minutes after the
fireplace has been turned OFF. Whenever the
fan is turned ON, the FAN will start up on the
high setting for 10 seconds before adjusting to
the previous user setting.
Press the PILOT button to activate or deactivate
the constant pilot. The control module will beep
once indicating constant pilot has been activated. A double beep indicates the constant pilot
has been deactivated.
FLAME
SENSE
CONTROL MODULE
ORANGE
6V DC
SUPPLY
IGNITER
FLAME
MODULATION
WHITE
TO JUNCTION
BOX (120V)
Figure 7. Child Lock Switch
RC200 12V DC
(A23 X 1)
WHITE
Select
Menu
Setting the Child Lock
Select
Press the POWER button to turn the fireplace
ON and OFF. The fireplace will first ignite the pilot. Once the pilot flame is established the main
burner will be lit.
Menu
Notice: Whenever the fireplace is cycled from OFF to
ON, the main burner will light on high for 10 seconds before
returning to the previous user setting.
3 PRONG 120VAC
AUX200 MODULE
FAN
TO JUNCTION
BOX 120VAC
BATTERY PACK
6V DC (AA X 4)
ORANGE
(PILOT)
GREEN
(MAIN)
RED
BLACK
BROWN
BROWN/RED
OPTIONAL ON/OFF
SWITCH
GROUND
Figure 8. RC200 Wiring Diagram
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 • 6/09
Power Outage
• If fireplace battery backup system IS installed at time of
power outage, fireplace operation will not be interrupted.
• If fireplace battery backup system IS NOT installed at
time of power outage, fireplace will shut off.  To resume
fireplace operation, install battery backup.
WARNING! Risk of burns! In the event of a wall switch
malfunction, DO NOT attempt to turn off the fireplace
manually using the control module. The decorative front
will be hot and severe burns may occur. Call you dealer
for assistance.
Frequently Asked Questions/Troubleshooting
Symptom
Possible Cause
Remote control will not transmit
Control module will not take
commands from remote control
Batteries
Verify battery is functional and installed correctly.
Remote control is in
Child Lock mode
Disengage Child Lock mode.
Control module is in
“REMOTE” mode
Ensure module switch is set to REMOTE.
Control module and
remote control are not
programmed to each
other
The control module will beep when it successfully receives a command. If it does not beep, clear module
memory and reprogram wall switch.
Control module is
unplugged. In case of
power outage, backup
batteries are depleted or
missing
If red LED light comes on when power button is pressed,
verify that the control module is plugged in the fireplace
junction box located in the controls area.  Also verify that
the batteries are installed in the battery pack.
Fan does not turn on when
fireplace is started
Built in time delay
The fireplace must run for seven minutes in order for the
fan to engage.
Fan does not turn off when
fireplace turned off
Built in time delay
The fan will run for twelve minutes after the fireplace is
turned off.
Fireplace shuts down after
extended periods
Built-in timer
The fireplace will automatically shut down after nine
hours of continuous operation in REMOTE mode.
External wired wall
switch
The fireplace cannot be turned off by remote if an external wired wall switch is installed and in the ON position.
Turn external wall switch to OFF.
Control module failure
At control module, turn off fireplace by sliding the ON/
OFF/REMOTE switch to OFF. Warning! Risk of Fire!
Fireplace is hot. Use caution when accessing module.
Fireplace is on but will not shut off
with the remote control
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
Corrective Action
Please contact your Hearth & Home Technologies
dealer with any questions or concerns.
For the location of your nearest
Hearth & Home Technologies dealer,
please visit www.fireside.com.
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 • 6/09

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Modify, Annotate, Fill forms, Extract, Assemble, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2009:06:23 10:37:09-05:00
Metadata Date                   : 2009:07:20 16:26:31+08:00
Modify Date                     : 2009:07:20 16:26:31+08:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 10547 bytes, use -b option to extract)
Instance ID                     : uuid:6f7e8f47-034f-425e-b783-5f74e021e418
Document ID                     : adobe:docid:indd:4d851d08-4f77-11de-b6d9-a29c7d9d7953
Rendition Class                 : proof:pdf
Derived From Instance ID        : 4d851d07-4f77-11de-b6d9-a29c7d9d7953
Derived From Document ID        : adobe:docid:indd:c0911579-39ad-11de-b0eb-93e5b4221773
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 180.00, 180.00, 180.00, 180.00, 180.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 180.00, 180.00, 180.00, 180.00, 180.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:e0ed69ee-21ed-4334-8af1-cdb0f362e03f, uuid:13F8A935413ADE1188B4BB64B4290838, uuid:16F8A935413ADE1188B4BB64B4290838, uuid:895C5324623ADE1188B4BB64B4290838, uuid:8DF9B2EC2C3EDE11B044F739DEE3E2CD, uuid:835C5324623ADE1188B4BB64B4290838, uuid:ecb06144-53ad-4cf9-996f-c7b5bbef3d55, uuid:bd77517b-6a5c-4aa4-b7cb-b4de6b3e5f35, uuid:bd77517b-6a5c-4aa4-b7cb-b4de6b3e5f35, uuid:bd77517b-6a5c-4aa4-b7cb-b4de6b3e5f35, uuid:bd77517b-6a5c-4aa4-b7cb-b4de6b3e5f35
Manifest Reference Document ID  : uuid:E2D2ADA1F364DB11A22ECEF114089A9C, uuid:12F8A935413ADE1188B4BB64B4290838, uuid:15F8A935413ADE1188B4BB64B4290838, uuid:885C5324623ADE1188B4BB64B4290838, uuid:8CF9B2EC2C3EDE11B044F739DEE3E2CD, uuid:825C5324623ADE1188B4BB64B4290838, uuid:2B914960E633DE119489CB0B81371D30, uuid:2486CD477F39DE1187BA88F92E2FD158, uuid:2486CD477F39DE1187BA88F92E2FD158, uuid:2486CD477F39DE1187BA88F92E2FD158, uuid:2486CD477F39DE1187BA88F92E2FD158
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 4
Creator                         : Adobe InDesign CS2 (4.0.5)

EXIF Metadata provided by EXIF.tools