HeathCo WLTRX5892 Video Security Light User Manual IC French Manual 5982 1

HeathCo LLC Video Security Light IC French Manual 5982 1

Exhibit D Users Manual per 2 1033 b3

THANK YOUWe appreciate the trust and condence you have placed in Deant through the purchase of this video motion security light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Deant!USE AND CARE GUIDEVIDEO MOTION SECURITY LIGHTQuestions, problems, missing parts? Before returning to the store, call Deant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday1-866-308-3976HOMEDEPOT.COMItem #1001814036Model #DFI-5892-WH
2Table of ContentsTable of Contents ......................................2Safety Information ....................................2Warranty ...................................................35-Year Limited Warranty ........................3Pre-Installation .........................................3Planning Installation ..............................3Specications ........................................3Tools Required .......................................4Hardware Included .................................5Package Contents ..................................5Installation ................................................6Operation...................................................8Care and Cleaning ..................................12Troubleshooting ......................................13Safety InformationPRECAUTIONS ƑPlease read and understand this entire manual before attempting to assemble, install, or operate this light xture. ƑThis light xture requires a 120-Volt AC power source. ƑSome codes require installation by a qualied electrician. ƑThis light xture must be properly grounded. ƑThis light xture should be installed outdoors to a wall or eave. ƑThe light xture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light xture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. ƑThe light xture/camera requires constant power to operate. Whenever the power is turned on to the light xture (either for the rst time or after a power outage), the light requires a 60-second boot-up period before the camera will be fully operational. ƑMany states regulate the use of security cameras and other recording devices. It is the purchaser’s sole responsibility to ensure compliance with all applicable laws and to provide any legally required notices. Check local laws regarding the use of any recording devices and cameras prior to installation.WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light xture.WARNING: Risk of re. Keep the lamp heads at least 2in. (51mm) from combustible materials.CAUTION: Burn hazard. Allow the light xture to cool before touching.NOTICE: Do not connect this light xture to a dimmer switch or timer. ƑThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ƑThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ƑCAN ICES-3 (B)/NMB-3(B)
3 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Warranty5-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.No service parts available for this product.Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.Pre-InstallationPLANNING INSTALLATIONBefore installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light xture.Estimated installation time: 30 minutesSPECIFICATIONSRange Up to 70 ft. (21.3 m) (Varies with surrounding temperature)PIR motion sensing angle Up to 180°Electrical load - LED 34 WattsLumens 2350Power requirements 120 VAC, 60 HzVideo resolution Hi: 1280 x 720 (720p), Med: 640 x 360, Low: 320 x 180Video frame rate Adjustable up to 25 fps (Default - 15 fps)Video viewing angle Up to 100°Operating temperature -13°F to +120°F (-25°C to +50°C)Mobile device requirements iPhone and Android compatible. See Homedepot.com for system requirements.
4Pre-Installation (continued)TOOLS REQUIREDPhillips screwdriver1/8 in. Flathead screwdriverWire strippers/cuttersCircuit tester Work gloves Silicone sealantLadder Safety goggles Mobile Device
5 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.HARDWARE INCLUDEDNOTE: Hardware shown to actual size. AA BB CC DD EE FRONT FF GGPart Description QuantityAA Rubber plug 1BB Mounting bracket screw 2CC Mounting bracket screw 2DD Large mounting bolt 1EE Small mounting bolt (pre-installed) 1FF Mounting bracket (not to scale) 1GG Mini screwdriver 1PACKAGE CONTENTSPart Description QuantityA Lamp head 2B Light xture 1C Motion sensor 1D Mounting plate 1E Camera 1CAEDBPre-Installation (continued)
6Installation1 Determining the mounting locationNOTE: The light xture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light xture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. ƑDetermine the mounting location – wall or eave mount. ƑPosition the lamp heads (A) in the general direction of the desired light coverage. ƑIf needed, rotate the motion sensor (C) so the text faces upward.Wall MountEave Mount180°THIS SIDE UP2 Removing the mounting plateNOTE: This xture comes with a mounting plate (D). It is pre-assembled on the light xture (B) for shipping.NOTE: The small mounting bolt (EE) is pre-installed in the light xture (B). Do not attempt to remove the small mounting bolt (EE). ƑUnscrew the small mounting bolt (EE) connecting the light xture (B) to the mounting plate (D) and remove the mounting plate (D).3 Installing the mounting bracketWARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light xture.NOTE: Six mounting bracket screws of various sizes are included. The installation will only require two. Discard the unused mounting bracket screws after installation. ƑRemove the existing light xture. ƑInstall the mounting bracket (FF) with the stamped word “FRONT” facing away from the junction box. Use the mounting bracket screws (BB or CC) that best t the junction box. ƑFirmly pull on the mounting bracket to verify it is securely mounted to the junction box. If necessary, use the screws that were removed from the existing light xture.FRONTFRONTEEDBBB or CCFFAC
7 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Installation (continued)4 Installing the mounting plate ƑRoute the junction box wires through the hole in the mounting plate (D). ƑPlace the mounting plate (D) against the junction box. ƑWhen mounting to a wall, the “UP” arrow must point upward. ƑWhen mounting to an eave, the “UP” arrow must point toward the building. ƑInsert the large mounting bolt (DD) through the mounting plate (D) hole located below the threaded hole, and thread it into the center hole of the mounting bracket (FF). Tighten the bolt (DD) securely. ƑFirmly pull on the mounting plate (D) to verify it is securely attached to the mounting bracket(FF).FRONTN (White/Blanc/Blanco)GNDTerreTierraUP/Haut/ArribaL (Black/Noir/Negro)UP/Haut/Arriba5 Making the electrical connections ƑInsert the junction box wires into the side of the terminal block and around the ground screw. Tighten terminal block screws using the mini-screwdriver (GG) and ground screw to secure the wires. ƑInsert the white wire from the junction box into the terminal marked “N (White)”. ƑInsert the black wire from the junction box into the terminal marked “L (Black)”. ƑConnect the bare or green ground wire from the junction box to the ground screw (marked with “GND”).N (White/Blanc/Blanco)GNDTerreTierraUP/Haut/ArribaL (Black/Noir/Negro)6 Mounting the light fixtureNOTICE: The two pins on the rear of the light xture must be inserted into the terminal block for the light to work. ƑAlign the bottom edge of the light xture (B) with the bottom edge of the mounting plate(D). Tilt the light xture (B) toward the mounting plate (D), making sure the light xture (B) is centered on the mounting plate (D). ƑTighten the small mounting bolt (EE) securely through the center of the mounting plate(D). Do not overtighten. ƑPush the rubber plug (AA) rmly into the mounting bolt hole on the light xture (B).EEAADBDDDDFF
8Installation (continued)7 Caulking around the light fixture ƑCaulk around the mounting plate (D) and mounting surface with silicone sealant (not included).Operation1 Adjusting the lamp headsWARNING: Risk of re. Keep the lamp heads at least 2in. (51mm) from combustible materials.CAUTION: Keep lamp heads 30° below horizontal to avoid water damage and electrical shock. ƑTurn the power on at the circuit breaker or fuse and turn on the wall switch. ƑIf needed, gently grasp the lamp heads (A) and tilt them up or down or side to side to adjust the light coverage area.180°THIS SIDE UP2 Rotating the sensor controls downward ƑRotate the motion sensor (C) so the text faces upward.180°THIS SIDE UPDCA
9 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Operation (continued)3 Downloading the mobile app ƑDownload the Noti™ mobile app. Search for the “Noti Video Solutions” app. ƑiOS Devices – Download the app from the App StoreSM. ƑAndroid Devices – Download the app from the Google Play™ store.4 Connecting the light to the mobile appNOTICE: The network password will be required to complete this process. ƑEnsure the power to the light is turned ON. Allow 60 seconds for system boot-up. ƑOn the mobile device, go to Settings > Wi-Fi and select “Noti_Video_SecurityXXXX” (“XXXX” represents the unique MAC address of each light xture) from the available Wi-Fi networks. ƑOnce connected, open the Noti app. The app will detect the new light. ƑSelect “Yes” to start the setup and the app will guide you through the remaining steps.NOTE: When creating a new Noti account, the username and password must be a minimum of 4 characters and a maximum of 12 characters. Alpha-numeric and/or special characters may be used.5 Viewing live videoThe Noti app provides live-stream video from the camera to a mobile device. ƑTap the name of the camera to be viewed. ƑWhile in the live-stream screen, the following options are available: ƑTap the video camera icon ( ) to start recording live video. Tap again to stop recording. ƑTap the camera icon ( ) to save a still image from the live-stream video. ƑTo return to the main app screen, tap the ( ) or “Back” button in the top left corner.NOTE: All videos and images will be saved to the mobile device currently being used to view the live-stream video.6 Understanding the motion detection processThis light has dual motion detection technologies. ƑThe light is controlled by a 180° PIR (passive infra-red) sensor. This sensor detects a temperature difference moving in front of it. When motion is detected after dark, the light will come on at the selected “Full Bright Intensity” level. ƑThe camera uses both the 180° PIR sensor as well as a 100° image sensor located within the camera software. The camera’s image sensor will not activate unless the PIR sensor rst detects a moving temperature difference within the detection zone. The camera will record motion day or night.
10Operation (continued)7 Using the event listTap the Events tab.An event is created each time the camera senses motion. ƑBasic Service – The event list will show the date and time the motion was detected. ƑPremium Service (available for an additional fee) – The event list will include the date, time, and video of the event each time motion was detected. The video of each event will also be available to download for 30 days.8 Receiving notificationsTap > Feature Settings > Notications to select the notication settings.If notications are turned on, an email and/or push notication is sent each time the camera senses motion. Tap on the notication to be taken to the live-view video screen (Basic service) or the Event video (Premium service).9 Adjusting the light settingsThe light settings allow you to adjust the full bright duration, the DualBrite® duration, and the percentages of light intensity.NOTE: Changes made to one light’s settings will not affect another light’s settings.Tap > Feature Settings > Light to select the light settings. ƑFull Bright Duration – This adjusts the amount of time the light will stay ON after all motion has stopped. ƑDualBrite Duration – This adjusts the amount of time the light stays ON at a reduced brightness level when no motion is detected. ƑFull Bright Intensity – This adjusts the intensity level of the light when motion is detected. ƑDualBrite Dimming Level – This adjusts the intensity level of the light when no motion is detected.10 Adjusting the camera settingsThe camera settings allow you to adjust the motion detection sensitivity, motion detection zones, and video quality.NOTE: Changes made to one camera’s settings will not affect another camera’s settings.NOTE: The higher the “Sensitivity” setting, the greater the possibility of false triggering. To reduce false triggering, select a lower setting.Tap > Feature Settings > Camera to select the camera settings. ƑMotion Detection – This adjusts the camera’s sensitivity to motion in its eld of view. ƑMotion Detection Zones – This adjusts the camera’s detection area to include or exclude zones in its eld of view. ƑAuto Adjust – Disabling this setting allows manual adjustments of the video’s quality settings. For best performance, leave the Auto Adjust ON.
11 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Operation (continued)11 Setting the sensor for testingNOTE: The light xture will operate during the day or night during testing. The light will stay on for 5 seconds after all motion is stopped.NOTE: The light requires a 60-second boot-up period before the camera will be fully operational.Tap > Feature Settings > Camera > Motion Detection to select the motion detection settings. The light xture will automatically enter “Test” mode whenever the “Motion Detection” option is selected. The light xture will remain in “Test” until one of the following actions occurs: ƑThe “Save” or “Cancel” option is selected. ƑNo movement during the testing process for 30 seconds. ƑThree minutes have passed without changing one of the on-screen settings.12 Adjusting the motion sensor detection zoneNOTE: The camera’s (E) detection zone is inside of the light’s detection zone. When the motion sensor (C) for the light is adjusted, the camera’s (E) motion sensor will also be adjusted.If motion is detected outside the camera’s detection zone, the light may turn on but the camera will not record an event. ƑPerform a “walk test”: walk in an arc across the front of the motion sensor (C). ƑWatch the light. The light will come on and the red LED will ash indicating motion has been detected. ƑStop, wait for the light to turn off, and then begin walking again. ƑContinue this process until the detection zone has been established. ƑIf needed, gently grasp the motion sensor (C) and move it from side to side or up and down to adjust the detection zone. ƑAdjust the “Motion Detection” sensitivity to High, Medium, or Low as needed.NOTE: The motion sensor (C) is more sensitive to motion moving across the front of the sensor. The motion sensor (C) is less sensitive to motion moving directly toward the front of the sensor.C and ECE
12Operation (continued)13 Adding multiple usersThe Noti system allows control of multiple users within an account.Tap > Advanced Settings > Manage Multiple Users. ƑTap the “Add Viewers” button and type the email address in the “To:” eld. ƑTap the “Send” button.NOTE: When adding multiple users, separate the email addresses with a semicolon.14 Adding system name and photoAdd a name and photo to represent the Noti system on the mobile device. The photo will be placed inside the blue circle icon next to the selected Noti system.Tap > Advanced Settings > System Name/Photo. ƑEnter a name for the Noti system. ƑSelect an existing photo and take a new photo to represent the Noti system.NOTE: The light settings and name are stored in the light xture. The photo is locally stored on the mobile device and is only visible on that device.15 Using manual modeManual mode overrides the motion sensor (C) and will turn the light on at the preset “Full Bright Intensity” level. This feature works day or night. The motion sensor (C) will reset to motion sensing mode at sunrise. ƑOn the main screen under the “Systems” tab, choose “ON”, “OFF”, or “AUTO” to control the lights for the selected Noti system.16 Deleting a Notifi systemTo delete a Noti system from an account: ƑTurn off the wall switch controlling the Noti system. ƑOn the main “Systems” screen, wait for the system to go ofine (the system name and image will turn gray). ƑOnce ofine, swipe the Noti system to be deleted to the left and tap the trashcan icon ( ). Care and Cleaning ƑTo prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only. ƑDo not use paints, solvents, or other chemicals on this light xture. They could cause a premature deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty. ƑDo not spray the light xture with a hose or power washer. ƑTo clean the camera lens, use a dry, microber cloth only.
13 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.TroubleshootingProblem Possible Cause SolutionThe light will not come on. ƑThe light switch is turned off. ƑTurn the light switch on. ƑThe fuse is blown or the circuit breaker is turned off. ƑReplace the fuse or turn the circuit breaker on. ƑThe light is not scheduled to come ON. ƑRecheck the light operation during the scheduled “DualBrite Duration” (after sunset). ƑThe circuit wiring is incorrect (if this is a new installation). ƑVerify the wiring is correct. ƑThe motion sensor is aimed in the wrong direction. ƑRe-aim the motion sensor to cover the desired area. ƑThe outside air temperature is close to the same as a person’s body heat. ƑIncrease the “Motion Detection” setting.The light comes on during the day. ƑThe light is scheduled to come ON. ƑAdjust the scheduled light operation in “DualBrite Duration.”The light comes on for no apparent reason. ƑThe motion sensor may be sensing small animals or automobile trafc. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. ƑThe “Motion Detection” setting is set too high. ƑDecrease the “Motion Detection” setting. ƑThe “DualBrite Duration” is operating at the preset “DualBrite Dimming Level” setting. ƑThe light xture is operating normally under these circumstances. The “DualBrite Duration” time is adjustable. ƑThe outside temperature is much warmer or cooler than a person’s body heat (summer or winter). ƑDecrease the “Motion Detection” setting. ƑThe light xture is wired through a dimmer or timer. ƑDo not use a dimmer or timer to control the light xture. Replace the dimmer or timer with a standard on/off wall switch.The lights stay ON too late in the “DualBrite Duration” setting. ƑThe “DualBrite Duration” OFF time is set to late. ƑAdjust the “DualBrite Duration” OFF time to the desired setting.The lights do not stay ON late enough in the “DualBrite Duration” setting. ƑThe “DualBrite Duration” OFF time is set to early. ƑAdjust the “DualBrite Duration” OFF time to the desired setting.
14Problem Possible Cause SolutionThe lights stay on continuously. ƑThe motion sensor may be picking up a heat source, such as an air vent, dryer vent, or brightly painted, heat-reective surface. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. ƑThe motion sensor is in manual mode. ƑTurn the manual mode option to Off or Auto. See Using manual mode on page 12. ƑThe light xture is wired through a dimmer or timer. ƑDo not use a dimmer or timer to control the light xture. Replace the dimmer or timer with a standard on/off wall switch. ƑThe light xture is on the same circuit as a motor, transformer, or uorescent bulb. ƑInstall the light xture on a circuit without motors, transformers, or uorescent bulbs.The lights ash on and off. ƑHeat or light from the lamp heads may be turning the motion sensor on and off. ƑReposition the lamp heads away from the motion sensor. ƑHeat is being reected from other objects and may be turning the motion sensor on and off. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. The light xture is not responding to the app. ƑThe light is ofine (the system name and image are gray). ƑEnsure the light has power. ƑEnsure the light is connected to the wi- router. ƑThe light is unable to connect to the wi- (the system name and image are gray). ƑTurn the power to the light off. Wait 30 seconds and turn the power on. Wait 60 seconds for the light to boot-up.The app is not nding the light xture. ƑThe light may have been deleted from the account. ƑReconnect the light to the app (see step 4, page 9).Motion notications are not being sent to the app. ƑNotications are turned off in the app. ƑTurn notications on in the app (see step 8, page 10). ƑMotion is not being detected inside the camera’s detection zone. ƑRe-aim the motion sensor to cover the desired area or increase the “Motion Detection” setting.Troubleshooting (continued)
Questions, problems, missing parts? Before returning to the store, call Deant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday1-866-308-3976HOMEDEPOT.COMRetain this manual for future use.Apple and the Apple logos are trademarks of Apple Inc., registered in the U.S., and other countries. App Store is a service mark of Apple Inc.Google Play is a trademark of Google Inc.Android is a trademark of Google Inc.Wi-Fi® is a registered trademark of Wi-Fi Alliance
THANK YOUWe appreciate the trust and condence you have placed in Deant through the purchase of this video motion security light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Deant!USE AND CARE GUIDEVIDEO MOTION SECURITY LIGHTQuestions, problems, missing parts? Before returning to the store, call Deant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday1-866-308-3976HOMEDEPOT.COMItem #1001814036Model #DFI-5892-WH
17 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Table of ContentsTable of Contents ......................................2Safety Information ....................................2Warranty ...................................................35-Year Limited Warranty ........................3Pre-Installation .........................................3Planning Installation ..............................3Specications ........................................3Tools Required .......................................4Hardware Included .................................5Package Contents ..................................5Installation ................................................6Operation...................................................8Care and Cleaning ..................................12Troubleshooting ......................................13Safety InformationPRECAUTIONS ƑPlease read and understand this entire manual before attempting to assemble, install, or operate this light xture. ƑThis light xture requires a 120-Volt AC power source. ƑSome codes require installation by a qualied electrician. ƑThis light xture must be properly grounded. ƑThis light xture should be installed outdoors to a wall or eave. ƑThe light xture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light xture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. ƑThe light xture/camera requires constant power to operate. Whenever the power is turned on to the light xture (either for the rst time or after a power outage), the light requires a 60-second boot-up period before the camera will be fully operational. ƑMany states regulate the use of security cameras and other recording devices. It is the purchaser’s sole responsibility to ensure compliance with all applicable laws and to provide any legally required notices. Check local laws regarding the use of any recording devices and cameras prior to installation.WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light xture.WARNING: Risk of re. Keep the lamp heads at least 2in. (51mm) from combustible materials.CAUTION: Burn hazard. Allow the light xture to cool before touching.NOTICE: Do not connect this light xture to a dimmer switch or timer. ƑThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ƑLe présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. ƑCAN ICES-3 (B)/NMB-3(B)
18Warranty5-YEAR LIMITED WARRANTYWHAT IS COVEREDThis product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date of purchase. Purchase receipt is required for all warranty claims.WHAT IS NOT COVEREDThis guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.No service parts available for this product.Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.Pre-InstallationPLANNING INSTALLATIONBefore installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light xture.Estimated installation time: 30 minutesSPECIFICATIONSRange Up to 70 ft. (21.3 m) (Varies with surrounding temperature)PIR motion sensing angle Up to 180°Electrical load - LED 34 WattsLumens 2350Power requirements 120 VAC, 60 HzVideo resolution Hi: 1280 x 720 (720p), Med: 640 x 360, Low: 320 x 180Video frame rate Adjustable up to 25 fps (Default - 15 fps)Video viewing angle Up to 100°Operating temperature -13°F to +120°F (-25°C to +50°C)Mobile device requirements iPhone and Android compatible. See Homedepot.com for system requirements.
19 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Pre-Installation (continued)TOOLS REQUIREDPhillips screwdriver1/8 in. Flathead screwdriverWire strippers/cuttersCircuit tester Work gloves Silicone sealantLadder Safety goggles Mobile Device
20HARDWARE INCLUDEDNOTE: Hardware shown to actual size. AA BB CC DD EE FRONT FF GGPart Description QuantityAA Rubber plug 1BB Mounting bracket screw 2CC Mounting bracket screw 2DD Large mounting bolt 1EE Small mounting bolt (pre-installed) 1FF Mounting bracket (not to scale) 1GG Mini screwdriver 1PACKAGE CONTENTSPart Description QuantityA Lamp head 2B Light xture 1C Motion sensor 1D Mounting plate 1E Camera 1CAEDBPre-Installation (continued)
21 HOMEDEPOT.COMPlease contact 1-866-308-3976 for further assistance.Installation1 Determining the mounting locationNOTE: The light xture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light xture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. ƑDetermine the mounting location – wall or eave mount. ƑPosition the lamp heads (A) in the general direction of the desired light coverage. ƑIf needed, rotate the motion sensor (C) so the text faces upward.Wall MountEave Mount180°THIS SIDE UP2 Removing the mounting plateNOTE: This xture comes with a mounting plate (D). It is pre-assembled on the light xture (B) for shipping.NOTE: The small mounting bolt (EE) is pre-installed in the light xture (B). Do not attempt to remove the small mounting bolt (EE). ƑUnscrew the small mounting bolt (EE) connecting the light xture (B) to the mounting plate (D) and remove the mounting plate (D).3 Installing the mounting bracketWARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light xture.NOTE: Six mounting bracket screws of various sizes are included. The installation will only require two. Discard the unused mounting bracket screws after installation. ƑRemove the existing light xture. ƑInstall the mounting bracket (FF) with the stamped word “FRONT” facing away from the junction box. Use the mounting bracket screws (BB or CC) that best t the junction box. ƑFirmly pull on the mounting bracket to verify it is securely mounted to the junction box. If necessary, use the screws that were removed from the existing light xture.FRONTFRONTEEDBBB or CCFFAC
22Installation (continued)4 Installing the mounting plate ƑRoute the junction box wires through the hole in the mounting plate (D). ƑPlace the mounting plate (D) against the junction box. ƑWhen mounting to a wall, the “UP” arrow must point upward. ƑWhen mounting to an eave, the “UP” arrow must point toward the building. ƑInsert the large mounting bolt (DD) through the mounting plate (D) hole located below the threaded hole, and thread it into the center hole of the mounting bracket (FF). Tighten the bolt (DD) securely. ƑFirmly pull on the mounting plate (D) to verify it is securely attached to the mounting bracket(FF).FRONTN (White/Blanc/Blanco)GNDTerreTierraUP/Haut/ArribaL (Black/Noir/Negro)UP/Haut/Arriba5 Making the electrical connections ƑInsert the junction box wires into the side of the terminal block and around the ground screw. Tighten terminal block screws using the mini-screwdriver (GG) and ground screw to secure the wires. ƑInsert the white wire from the junction box into the terminal marked “N (White)”. ƑInsert the black wire from the junction box into the terminal marked “L (Black)”. ƑConnect the bare or green ground wire from the junction box to the ground screw (marked with “GND”).N (White/Blanc/Blanco)GNDTerreTierraUP/Haut/ArribaL (Black/Noir/Negro)6 Mounting the light fixtureNOTICE: The two pins on the rear of the light xture must be inserted into the terminal block for the light to work. ƑAlign the bottom edge of the light xture (B) with the bottom edge of the mounting plate(D). Tilt the light xture (B) toward the mounting plate (D), making sure the light xture (B) is centered on the mounting plate (D). ƑTighten the small mounting bolt (EE) securely through the center of the mounting plate(D). Do not overtighten. ƑPush the rubber plug (AA) rmly into the mounting bolt hole on the light xture (B).EEAADBDDDDFF
23 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Installation (continued)7 Caulking around the light fixture ƑCaulk around the mounting plate (D) and mounting surface with silicone sealant (not included).Operation1 Adjusting the lamp headsWARNING: Risk of re. Keep the lamp heads at least 2in. (51mm) from combustible materials.CAUTION: Keep lamp heads 30° below horizontal to avoid water damage and electrical shock. ƑTurn the power on at the circuit breaker or fuse and turn on the wall switch. ƑIf needed, gently grasp the lamp heads (A) and tilt them up or down or side to side to adjust the light coverage area.180°THIS SIDE UP2 Rotating the sensor controls downward ƑRotate the motion sensor (C) so the text faces upward.NOTICE: All clearances must be maintained. See Safety Information on page 2.NOTICE: The Noti™ mobile app must be downloaded to operate the light xture. See Step 3 on page 9 for instructions.180°THIS SIDE UPDCA
24Operation (continued)3 Downloading the mobile app ƑDownload the Noti™ mobile app. Search for the “Noti Video Solutions” app. ƑiOS Devices – Download the app from the App StoreSM. ƑAndroid Devices – Download the app from the Google Play™ store.4 Connecting the light to the mobile appNOTICE: The network password will be required to complete this process. ƑEnsure the power to the light is turned ON. Allow 60 seconds for system boot-up. ƑOn the mobile device, go to Settings > Wi-Fi and select “Noti_Video_SecurityXXXX” (“XXXX” represents the unique MAC address of each light xture) from the available Wi-Fi networks. ƑOnce connected, open the Noti app. The app will detect the new light. ƑSelect “Yes” to start the setup and the app will guide you through the remaining steps.NOTE: When creating a new Noti account, the username and password must be a minimum of 4 characters and a maximum of 12 characters. Alpha-numeric and/or special characters may be used.5 Viewing live videoThe Noti app provides live-stream video from the camera to a mobile device. ƑTap the name of the camera to be viewed. ƑWhile in the live-stream screen, the following options are available: ƑTap the video camera icon ( ) to start recording live video. Tap again to stop recording. ƑTap the camera icon ( ) to save a still image from the live-stream video. ƑTo return to the main app screen, tap the ( ) or “Back” button in the top left corner.NOTE: All videos and images will be saved to the mobile device currently being used to view the live-stream video.6 Understanding the motion detection processThis light has dual motion detection technologies. ƑThe light is controlled by a 180° PIR (passive infra-red) sensor. This sensor detects a temperature difference moving in front of it. When motion is detected after dark, the light will come on at the selected “Full Bright Intensity” level. ƑThe camera uses both the 180° PIR sensor as well as a 100° image sensor located within the camera software. The camera’s image sensor will not activate unless the PIR sensor rst detects a moving temperature difference within the detection zone. The camera will record motion day or night.
25 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Operation (continued)7 Using the event listTap the Events tab.An event is created each time the camera senses motion. ƑBasic Service – The event list will show the date and time the motion was detected. ƑPremium Service (available for an additional fee) – The event list will include the date, time, and video of the event each time motion was detected. The video of each event will also be available to download for 30 days.8 Receiving notificationsTap > Feature Settings > Notications to select the notication settings.If notications are turned on, an email and/or push notication is sent each time the camera senses motion. Tap on the notication to be taken to the live-view video screen (Basic service) or the Event video (Premium service).9 Adjusting the light settingsThe light settings allow you to adjust the full bright duration, the DualBrite® duration, and the percentages of light intensity.NOTE: Changes made to one light’s settings will not affect another light’s settings.Tap > Feature Settings > Light to select the light settings. ƑFull Bright Duration – This adjusts the amount of time the light will stay ON after all motion has stopped. ƑDualBrite Duration – This adjusts the amount of time the light stays ON at a reduced brightness level when no motion is detected. ƑFull Bright Intensity – This adjusts the intensity level of the light when motion is detected. ƑDualBrite Dimming Level – This adjusts the intensity level of the light when no motion is detected.10 Adjusting the camera settingsThe camera settings allow you to adjust the motion detection sensitivity, motion detection zones, and video quality.NOTE: Changes made to one camera’s settings will not affect another camera’s settings.NOTE: The higher the “Sensitivity” setting, the greater the possibility of false triggering. To reduce false triggering, select a lower setting.Tap > Feature Settings > Camera to select the camera settings. ƑMotion Detection – This adjusts the camera’s sensitivity to motion in its eld of view. ƑMotion Detection Zones – This adjusts the camera’s detection area to include or exclude zones in its eld of view. ƑAuto Adjust – Disabling this setting allows manual adjustments of the video’s quality settings. For best performance, leave the Auto Adjust ON.
26Operation (continued)11 Setting the sensor for testingNOTE: The light xture will operate during the day or night during testing. The light will stay on for 5 seconds after all motion is stopped.NOTE: The light requires a 60-second boot-up period before the camera will be fully operational.Tap > Feature Settings > Camera > Motion Detection to select the motion detection settings. The light xture will automatically enter “Test” mode whenever the “Motion Detection” option is selected. The light xture will remain in “Test” until one of the following actions occurs: ƑThe “Save” or “Cancel” option is selected. ƑNo movement during the testing process for 30 seconds. ƑThree minutes have passed without changing one of the on-screen settings.12 Adjusting the motion sensor detection zoneNOTE: The camera’s (E) detection zone is inside of the light’s detection zone. When the motion sensor (C) for the light is adjusted, the camera’s (E) motion sensor will also be adjusted.If motion is detected outside the camera’s detection zone, the light may turn on but the camera will not record an event. ƑPerform a “walk test”: walk in an arc across the front of the motion sensor (C). ƑWatch the light. The light will come on and the red LED will ash indicating motion has been detected. ƑStop, wait for the light to turn off, and then begin walking again. ƑContinue this process until the detection zone has been established. ƑIf needed, gently grasp the motion sensor (C) and move it from side to side or up and down to adjust the detection zone. ƑAdjust the “Motion Detection” sensitivity to High, Medium, or Low as needed.NOTE: The motion sensor (C) is more sensitive to motion moving across the front of the sensor. The motion sensor (C) is less sensitive to motion moving directly toward the front of the sensor.C and ECE
27 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Operation (continued)13 Adding multiple usersThe Noti system allows control of multiple users within an account.Tap > Advanced Settings > Manage Multiple Users. ƑTap the “Add Viewers” button and type the email address in the “To:” eld. ƑTap the “Send” button.NOTE: When adding multiple users, separate the email addresses with a semicolon.14 Adding system name and photoAdd a name and photo to represent the Noti system on the mobile device. The photo will be placed inside the blue circle icon next to the selected Noti system.Tap > Advanced Settings > System Name/Photo. ƑEnter a name for the Noti system. ƑSelect an existing photo and take a new photo to represent the Noti system.NOTE: The light settings and name are stored in the light xture. The photo is locally stored on the mobile devaice and is only visible on that device.15 Using manual modeManual mode overrides the motion sensor (C) and will turn the light on at the preset “Full Bright Intensity” level. This feature works day or night. The motion sensor (C) will reset to motion sensing mode at sunrise. ƑOn the main screen under the “Systems” tab, choose “ON”, “OFF”, or “AUTO” to control the lights for the selected Noti system.16 Deleting a Notifi systemTo delete a Noti system from an account: ƑTurn off the wall switch controlling the Noti system. ƑOn the main “Systems” screen, wait for the system to go ofine (the system name and image will turn gray). ƑOnce ofine, swipe the Noti system to be deleted to the left and tap the trashcan icon ( ). Care and Cleaning ƑTo prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only. ƑDo not use paints, solvents, or other chemicals on this light xture. They could cause a premature deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty. ƑDo not spray the light xture with a hose or power washer. ƑTo clean the camera lens, use a dry, microber cloth only.
28TroubleshootingProblem Possible Cause SolutionThe light will not come on. ƑThe light switch is turned off. ƑTurn the light switch on. ƑThe fuse is blown or the circuit breaker is turned off. ƑReplace the fuse or turn the circuit breaker on. ƑThe light is not scheduled to come ON. ƑRecheck the light operation during the scheduled “DualBrite Duration” (after sunset). ƑThe circuit wiring is incorrect (if this is a new installation). ƑVerify the wiring is correct. ƑThe motion sensor is aimed in the wrong direction. ƑRe-aim the motion sensor to cover the desired area. ƑThe outside air temperature is close to the same as a person’s body heat. ƑIncrease the “Motion Detection” setting.The light comes on during the day. ƑThe light is scheduled to come ON. ƑAdjust the scheduled light operation in “DualBrite Duration.”The light comes on for no apparent reason. ƑThe motion sensor may be sensing small animals or automobile trafc. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. ƑThe “Motion Detection” setting is set too high. ƑDecrease the “Motion Detection” setting. ƑThe “DualBrite Duration” is operating at the preset “DualBrite Dimming Level” setting. ƑThe light xture is operating normally under these circumstances. The “DualBrite Duration” time is adjustable. ƑThe outside temperature is much warmer or cooler than a person’s body heat (summer or winter). ƑDecrease the “Motion Detection” setting. ƑThe light xture is wired through a dimmer or timer. ƑDo not use a dimmer or timer to control the light xture. Replace the dimmer or timer with a standard on/off wall switch.The lights stay ON too late in the “DualBrite Duration” setting. ƑThe “DualBrite Duration” OFF time is set to late. ƑAdjust the “DualBrite Duration” OFF time to the desired setting.The lights do not stay ON late enough in the “DualBrite Duration” setting. ƑThe “DualBrite Duration” OFF time is set to early. ƑAdjust the “DualBrite Duration” OFF time to the desired setting.
29 HOMEDEPOT.COM Please contact 1-866-308-3976 for further assistance.Problem Possible Cause SolutionThe lights stay on continuously. ƑThe motion sensor may be picking up a heat source, such as an air vent, dryer vent, or brightly painted, heat-reective surface. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. ƑThe motion sensor is in manual mode. ƑTurn the manual mode option to Off or Auto. See Using manual mode on page 12. ƑThe light xture is wired through a dimmer or timer. ƑDo not use a dimmer or timer to control the light xture. Replace the dimmer or timer with a standard on/off wall switch. ƑThe light xture is on the same circuit as a motor, transformer, or uorescent bulb. ƑInstall the light xture on a circuit without motors, transformers, or uorescent bulbs.The lights ash on and off. ƑHeat or light from the lamp heads may be turning the motion sensor on and off. ƑReposition the lamp heads away from the motion sensor. ƑHeat is being reected from other objects and may be turning the motion sensor on and off. ƑDecrease the “Motion Detection” setting or reposition the motion sensor. The light xture is not responding to the app. ƑThe light is ofine (the system name and image are gray). ƑEnsure the light has power. ƑEnsure the light is connected to the wi- router. ƑThe light is unable to connect to the wi- (the system name and image are gray). ƑTurn the power to the light off. Wait 30 seconds and turn the power on. Wait 60 seconds for the light to boot-up.The app is not nding the light xture. ƑThe light may have been deleted from the account. ƑReconnect the light to the app (see step 4, page 9).Motion notications are not being sent to the app. ƑNotications are turned off in the app. ƑTurn notications on in the app (see step 8, page 10). ƑMotion is not being detected inside the camera’s detection zone. ƑRe-aim the motion sensor to cover the desired area or increase the “Motion Detection” setting.Troubleshooting (continued)
Questions, problems, missing parts? Before returning to the store, call Deant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday1-866-308-3976HOMEDEPOT.COMRetain this manual for future use.Apple and the Apple logos are trademarks of Apple Inc., registered in the U.S., and other countries. App Store is a service mark of Apple Inc.Google Play is a trademark of Google Inc.Android is a trademark of Google Inc.Wi-Fi® is a registered trademark of Wi-Fi Alliance

Navigation menu