Heiman Technology HS1CAZ Smart Carbon Monoxide Sensor User Manual

Shenzhen Heiman Technology Co.,Ltd. Smart Carbon Monoxide Sensor

User Manual

Smart Carbon Monoxide SensorUser ManualClick “Add Device” on the APP interface, and enter the networking mode.Technical DataTipsInstallation InstructionInstallation DrawingProduct Introduction*Please read the user manual carefully before operation.The guide picture is for reference only. please in kind prevail1.Install  the  sensor  in  bedroom  and  living  area  or anywhere CO may leak, make sure each sleeping ar ea  ca n  hea r  sound  a larm  wh en  ch o o se installation position.2.Avoid  suppressing  or  falling  down  sensors,  keep sensors  away  from  humid,  high  voltage,   strong magnetic and children.3.Do not suggest install sensors in garage, kitchen, boiler and  places  where  sensor  may  false  alarm. Do not install in dirty, dusty or greasy places, oily, dust or household chemicals may damage internal sensor, and make sensor can not work normally.4.Sensors  can  support  wall  mounted  or  placing  on the table, household and travel essential.Screw the sensor into bracket, please remove  the double - sided  adhesive  membrane  on  the  installation base, and stick on the wall.Sensor Installation BaseAnticlockwise rotating  the bracket out  from the  installation  base,   then   remove    the battery insulating strip to make detector on power.*Please  replace  battery  correctly,  following  the battery posi negative electrode.   tive and  Green-  flash alternatively oncered-yellow-green LEDGreen,red and yellow LED flash alternatively onceRed LED flashYellow LED flash twice every 10 secondsGreen LED flash every 53 secondsRed LED flash every 53 secondsYellow LED flash twice4 beeps1 beep4 beeps2 beeps every 10 seconds1 beep every 53 seconds\4 beeps every 10 secondsStatus LED Indicator Alarm Please take following advices for reference if sensors can not work normally:1.Replace battery in time, if  voltage  too low and reach effective life  span. (Check table 1 for state reference)2.Please clean sensor if the fault resulted from dust or oil stain ( Check table 1for state reference).3.Make sure sensors screw into the base correctly.     Press test button on the product for 3 seconds,  shows  in  above picture,  till  alarm  happens  (  check  table  1  for  state  reference). Suggest test sensor at least once a week. Please pay attention once alarm happens.Installation Step1Installation Step2Installation Step3Installation Step4Chart1CR123A1, This product can not be used for detecting natural gas(methane),  propane,  butane  and  other combustible gas.2,  Clean  once  a  month,  users  may  use  household vacuum cleaner and soft brush when cleaning.3,  Do  not  use  cleanser  or  solvent  wipe  sensors, please avoid spraying air freshener, hair spray, oil paint or other aerosol near sensors.4,  Effective  working  life  span  is  5  years,  suggest replace every  5  years  no  matter  there  is  fault  or not. (Battery life span is 3 years).5, Please be attention when alarm happens. Shut-off valves  immediately,  opening  the  window,  make sure  indoor  airiness.  Besides  using  sensors correctly,  users  should  strengthen  the consciousness of fire protection.TestPreheatingAlarmMalfunctionLow  batteryNormal  working Expired  sensorStatus and battery replacement Troubleshooting  and testMinimum recommended installationAdditional recommended installationBedroom Bedroon BedroomLivingroomKitchenBasementGagrageAisleTo increase safety factors  in  single-layer house, suggest to install at least a sensor in each bedroom and install a sensor at 6m from chimney and  gas fixture.To increase safety factors in multi-layer house,  suggest to install at least a sensor in each bedroom, install  at least one sensor in basement. Please install a sensor at 6m from chimney and  gas fixture.Networking HoleLED IndicatorAccording to APP prompt, press the networking button 3 times in 1.5 seconds until green light flash, (the longest networking time is 30 seconds) APP interface p rompted, networking success.Select  device,  click  "delete"  on  APP,    then  press  the networking button 3 times in 1.5 seconds until the green light flashes  slowly  for  6  times,  which  indicates  network  is disconnected successfully        This  product  is  a  smart  carbon  monoxide sensor, adopts super low power consumption Z-wave   wireless networking technology,  used  for detecting  carbon monoxide. Sensor adopts high performance  electrochemical  sensor,  support sound and flash alarm, It has high stability, super low power consumption, little sensitivity drift and many  other  features.  Free  installation  design, support instant bonding.1.Working Voltage:DC3V(CR123A  Lithium Battery)2. St atic Current:≤20uA3.Alarm Current:≤60mA 4.Alarm Sound:85 dB/ 1m                   5.Alarm Sensitivity:30ppm 120mins alarm                                               50ppm 60-90mins alarm                                               100ppm 10-40mins alarm                                                300ppm 3mins alarm 6.Networking:Z-wave  Ad-Hoc Networking   7.Wireless Networking Distance:≥70m(open area)8.Working Temperature:-10℃ ~ +5 0℃9.Environment Humidity:≤ 95%RH10.Dimension:60* 60*49.2mm76 8 9 10 111 2 345HS1CA-Z
  FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •  Reorient or relocate the receiving antenna. •  Increase the separation between the equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help.  Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu