Hewlett Packard Enterprise 550-10016-7 WLAN atbtg mini-PCI module User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	657795
Application ID	ArHY0CeRjd81Xshosl/xXA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.29kB (266080 bits)
Date Submitted	2006-05-15 00:00:00
Date Available	2006-05-15 00:00:00
Creation Date	2006-05-11 10:29:50
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2006-05-11 10:29:50
Document Title	Microsoft Word - CM9-C1 Installation Instructions.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	dwallace

CM9-C1 Installation
MODULAR USAGE
This device is intended only for installation into the Miltope
Cabin Access Point (CAP) under the following conditions:
1) The antenna must be installed such that 20 cm is
maintained between the antenna and users.
2) The transmitter module may not be co-located with any
other transmitter or antenna
3) The final product containing this device must be labeled
in a visible manner with the following; “ Contains FCC ID
RTP550-10016-7”
4) The end product user manual must contain the following
information in a prominent location; “Important Note: To
comply with FCC RF exposure requirements, the
antenna used for this transmitter must be installed to
provide a separation distance of at least 20cm from all
persons and must not be co-located or operated in
conjunction with any other antenna or transmitter.
5) This radio module is approved for use only in the Miltope
CAP (Cabin Access Point) which is deployed only in
aircraft and is professionally installed per FAA
regulations.
200 West Street
Waltham, MA 02451
USA
phone:
fax:
+1 781-684-0001
+1 781-684-0009
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC
Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or peripheral devices) any changes or
modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
200 West Street
Waltham, MA 02451
USA
phone:
fax:
+1 781-684-0001
+1 781-684-0009
CM9-C1 IMPORTANT OPERATION INFORMATION
This device has been designed to operate with the antennas listed below, and
having a maximum gain of 4.85 dBi@ 2.4 GHz, 5.0 dBi @ 5.25GHz and 4.0 dBi
@ 5.875GHz. Antennas not included in this list or having a gain greater than
those listed are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that permitted for successful communication.
Operation in the band 5.15-5.25GHz is restricted to indoor use only.
Approved antennas
The table below lists the antennas approved for use with the model CM9C1:
Manufacturer
Part #
2.4 GHz Gain
5.3 GHz Gain
5.7 GHz Gain
Miltope
901167-2
2.6 dBi
1.2 dBi
1.2 dBi
Indoor
Miltope
901563-2
4.85 dBi
5.0 dBi
4.0 dBi
Outdoor
Miltope
901167-1
3.5 dBi
3.5 dBi
3.5 dBi
Indoor
Miltope
901058-1
5.0 dBi
N/A
N/A
Gore
GSC10-82701-XX
-30 dBi
-30 dBi
-30 dBi
200 West Street
Waltham, MA 02451
USA
Location
Outdoor
phone:
fax:
Indoor
+1 781-684-0001
+1 781-684-0009

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c4430538-493a-4809-b057-1f9982ff0d04
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2006:05:11 10:29:50-04:00
Create Date                     : 2006:05:11 10:29:50-04:00
Document ID                     : uuid:65babfcf-71c9-4546-a61e-f5067ca7648e
Format                          : application/pdf
Title                           : Microsoft Word - CM9-C1  Installation Instructions.doc
Creator                         : dwallace
Author                          : dwallace

EXIF Metadata provided by EXIF.tools