Hirschmann Car Communication RMM-W-26187 RMM-W User Manual Mounting Instruction
Hirschmann Car Communication GmbH RMM-W Mounting Instruction
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3232977 |
| Application ID | zq1z7f+9w1DhpnkPmPfbcw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 112.69kB (1408630 bits) |
| Date Submitted | 2016-12-19 00:00:00 |
| Date Available | 2017-06-17 00:00:00 |
| Creation Date | 2016-12-19 15:14:31 |
| Producing Software | Microsoft® Word 2010 |
| Document Lastmod | 2016-12-19 15:14:31 |
| Document Title | Mounting Instruction |
| Document Creator | Microsoft® Word 2010 |
| Document Author: | Jens.Sarup@Emerson.com |
RMM-W RMM- W User Manual Emerson Commercial & Residential Solutions Transportation Solutions Axel Kiers Vej 5A 8270 Højbjerg, Denmark www.emerson.com T +45 7023 4444 F +45 7023 6044 RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Copyright Emerson All Rights Reserved Transportation Solutions Author: Jens Sarup Page 1 of 16 1 DECLARATION OF CONFORMITY Environmental Specifications, markings and certifications CE EMC Directive 2014/30/EC Low Voltage Directive 2014/35/EC RED Directive 2014/53/EC RoHS Directive 2011/65/EC WEE Directive 2002/96/EC Battery Directive 2006/66/EC 1.1 FCC and IC Rules This device complies with Part 15 of the FCC Rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device has been designed to operate with the antennas listed below, and having a maximum gain of 4 dBi (Cellular) and 6.25 dBi (Bluetooth Low Energy). Antennas not included in this list or having a gain greater than 4 dBi (Cellular) and 6.25 dBi (Bluetooth Low Energy) are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that permitted for successful communication. RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 2 of 16 Régulations FCC/IC Cet appareil respecte la partie 15 des regulations FCC. L’utilisation est sujette aux deux conditions suivantes: (1) cet appareil doit ne pas pouvoir causer d’ interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris celle risquant de causer une utilisation non-desirée. Cet appareil est en conformité avec les normes de spécification radio exemptés de licence de l’industrie canadienne. L’utilisation est sujette aux deux conditions suivantes: (1) cet appareil doit ne pas pouvoir causer d’ interférences, et (2) cet appareil doit accepter toute interférence, y compris celle risquant de causer une utilisation non-desirée de l’appareil. Cet équipement a été testé et respecte les limites pour un appareil numérique de classe B, selon la partie 15 de la réglementation FCC. Ces limites sont conçues afin de fournir une protection raisonnable contre toute interférence nocive au sein d’une installation résidentielle. Cet équipement peut générer, utiliser et émettre de l’énergie dans le champs des fréquences radio et, en cas d’installation et d’usage en accord avec les instructions, causer des interférences nocives à la communication radio. Cependant, la garantie qu’aucune interférence ne peut avoir lieu pour une installation particulière ne peut être apportée. Si cet équipement cause des interférences nocives à la réception radio ou TV, pouvant être mesurées en éteignant puis en rallumant l’équipement, l’utilisateur est encouragé à essayer de corriger les interférences en prenant l’une des mesures suivantes: Réorienter ou déplacer l’antenne de reception. Augmenter la distance de séparation entre l’équipement et le récepteur. Connecter l’équipement à une prise sur un circuit différent de celui sur lequel le récepteur est connecté. Demander conseil au vendeur ou à un technicien radio/TV expérimenté. Cet appareil a été concu afin d’opérer les antennes citées dans la liste figurant ci-dessous, et ayant un gain maximal de 4 dBi (mobile) et 6,25 dBi (Bluetooth Low Energy). Les antennes non-inclues dans cette liste ou ayant un gain supérieur à 4 dBi (mobile) et 6,25 dBi (Bluetooth Low Energy) sont strictement inderdites d’utilisation avec cet appareil. L’impédance d’antenne requise est de 50 ohms. Afin de réduire une éventuelle interférence radio avec d’autres utilisateurs, le type d’antenne ainsi que son gain doivent être choisis de telle manière que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas celle qui est permise pour qu’une communication soit possible. RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 3 of 16 WARNING! FCC and IC Radiation Exposure Statement: This device complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled environment under the following conditions: 1. This device should be installed and operated such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) & user’s/nearby person’s body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3. Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment. ATTENTION! Énoncé d’exposition à la radiation FCC et IC: 1. Cet équipement doit être installé et utilisé de manière à ce qu’une distance minimale de 20cm soit maintenue en permanence entre l’émetteur (antenne) et le corps de l’utilisateur/d’une personne à proximité. 2. Cet émetteur ne doit pas être colocalisé ou utilisé conjointement avec d’autres antennes ou émetteurs. 3. Tout changement ou modification n’ayant pas été expressement approuvé par le parti responsable de la mise en conformité peut entraîner une annulation de l’autorisation de l’utilisateur à opérer l’équipement. RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 4 of 16 Batteries: Rechargeable batteries Depending on variant the RMM-W device includes one or two rechargeable batteries. Generally, the device has been designed that no battery replacement by the operator is intended throughout the complete service life. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY ANY INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Batteries rechargeables En fonction de la variante considérée, l’appareil RMM-W peut inclure une ou deux batteries rechargeables. En général, l’appareil a été concu de telle manière à ce qu’aucun remplacement de batterie de la part de l’opérateur soit prévu au long de sa durée de vie complète. ATTENTION: RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR TOUT TYPE INCORRECT. SUIVRE LES INSTRUCTIONS AFIN DE DISPOSER DES BATTERIES USÉES. 1.2 Safety Warnings Caution contains Static Sensitive Device Attention Contient des composants sensibles à la décharge électrostatique (ESDS) RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 5 of 16 1.3 RMM-W RMM-W RMM-W RMM-W Variants single battery without BLE Double battery without BLE single battery with BLE Double battery with BLE RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W P/N 7916-001 P/N 7916-002 P/N 7916-003 P/N 7916-004 Transportation Solutions Author: Jens Sarup Page 6 of 16 Mounting Instruction Table of Contents DECLARATION OF CONFORMITY 1.1 1.2 1.3 FCC and IC Rules Safety Warnings Variants RMM-W CONTAINER TYPES 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Thermo King MP 3000 Thermo King MP4000 Daikin Decos II/III Daikin Zestia Carrier ML2i/ML3 Carrier ThinLine StarCool 10 11 12 13 14 15 DOCUMENT REVISION RECORD 16 RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 7 of 16 2 RMM-W The RMM-W is a remote wireless communication device designed for refrigerated containers. The RMM-W unit provides wireless technologies for fast data transfer, long distance communication and tracking. The RMM-W unit uses machine-to-machine cell phone technology to forward all exceptions such as alarms and power on/off events as they occur, and will provide full set of data at pre-set scheduled intervals to the Emerson - ProAct™ Server. The RMM-W is to be fastened with tape from 3M, specification of tape can be found on below link http://multimedia.3m.com/mws/media/1021181O/3m-acrylic-foam-tape-px5000.pdf Attention! In order to ensure proper and durable installation with adhesive tape it is mandatory to follow the Tape manufacturer’s Usage Guidelines for Installation. Surface conditioning and cleaning as well a the process window for temperature during installation have to be respected in any case. The guideline can be found on below link http://multimedia.3m.com/mws/media/999184O/3m-automotive-acrylic-foam-tape-generalinstructural-manual.pdf RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 8 of 16 3 3.1 CONTAINER TYPES Thermo King MP 3000 RMM-W RMM-W Antenna To be updated with further pictures as soon as connection board to controller is ready. RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 9 of 16 3.2 Thermo King MP4000 RMM-W RMM-W Antenna Antenna placement same as MP3000 RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 10 of 16 3.3 Daikin Decos II/III RMM-W mounted on isolated plate RMM-W Antenna RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 11 of 16 3.4 Daikin Zestia To be updated RMM-W RMM-W Antenna RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 12 of 16 3.5 Carrier ML2i/ML3 RMM-W RMM-W Antenna RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 13 of 16 3.6 Carrier ThinLine To be updated RMM-W Antenna RMM-W Antenna Optional if correct bracket installed from Carrier. RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 14 of 16 3.7 StarCool RMM-W RMM-W Antenna RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W Transportation Solutions Author: Jens Sarup Page 15 of 16 Document Revision Record Rev. Date Author 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 060616 060816 310816 071116 071116 151116 121216 191216 191216 191216 JES YS JES JES JES JES JES JES JES JES Brief description of change Pages affected Original issue TK Controller added FCC text included Declaration of conformity and battery handling included Variant included in the document French cautions added Additional French text added Additional FCC text added VHB tape information added Handling of VHB tape added RMM-W Mounting Instruction_V1.9.docx Updated: 2016-12-19 Project RMM-W All All All All All All All All All Transportation Solutions Author: Jens Sarup Page 16 of 16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 16 Language : en-US Tagged PDF : Yes Title : Mounting Instruction Author : Jens.Sarup@Emerson.com Subject : RMM-W Creator : Microsoft® Word 2010 Create Date : 2016:12:19 15:14:31+01:00 Modify Date : 2016:12:19 15:14:31+01:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools