Hisense Broand Multimedia Technologies 001 Gigabit-Capable Passive Optical Network Single Family Unit User Manual

Hisense Broadband Multimedia Technologies Co.,Ltd Gigabit-Capable Passive Optical Network Single Family Unit User Manual

R66001_User manual_Rev1

Page 6 Page 5 7258G7257G WLANWIFI function is not active.WIFI function is active.ETH1-4 Management channel (OMCI) not active.Management channel (OMCI) active.POTSMGMTON Ethernet link is operational.Flashing Indicates data transmission / reception.OFF No Ethernet link or port is not equipped.ON Line is off hook (call active or in process).Flashing Slow Indicates ringing line.OFF Line is on hook (no call in process) or port is not equipped.Flashing Fast Software upgrade has failed.OFF Optical signal is present and operating nor-mally.ONOFFONFlashing Indicates data transmission / reception.OFFFunctions Select Model List Model 7259G 2POTS + 4GE + CATV + Return + WiFi 2POTS + 4GE + CATV + Return 2POTS + 4GE + CATV + WiFi 7253G 2POTS + 4GE + CATV 7281G 2POTS + 4GE + WiFi 7251G 2POTS + 4GE Indoor Type This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment to an outlet on a circuit dif- ferent from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Safety Caution Statement To satisfy FCC RF exposure requirement for mobile and base station transmission devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Environmental Requirements Rated Voltage: DC 12V Rated Current: 2A Operating Temperature: +5°C to +40°C Operating Relative Humidity: 5% to 85% Storage Temperature: -40°C to +60°C Storage Relative Humidity: 0% to 95% FCC Notice -2 The 72xxG North America edition is limited using channel 1-11. This limited operation can be only set by software and was done before the product down from the product line. All the products for North America marketing were embedded this limited before shipping. Customers have no way to choose the channel 12 & 13. FCC Notice -1
The 72xx SFU residential ONT delivers high quality Please adopt UL certificated UPSNOTICE: which meets Limited Power Source standard.Pins for the connector are Molex 46235-5002 OVERVIEW VoIP voice service, Ethernet data service for high- speed internet access and IPTV broadcast video plus – 2 POTS ports - provide voice telephone service – 4 LAN ports - provide Ethernet connectivity – WIFI ports - provide WIFI connectivity INSTALLATION The 72xx SFU ONT can be mounted vertically or hor- izontally on any flat surface. Unpack Unpack the unit and verify that it is free from shipping damage.: Desk Mount 1.) Set the unit on a flat surface considering the follo- wing: – within reach of the power source – no thermal obstructions – not in direct sunlight – user ability to monitor/operate the unit Wall Mount 1.) Use wall anchors or wood screws (if mounting to plywood mounted on a wall), spaced 5.125” apart center to center. Fiber Connection 1.) On the back left side of the unit is a fiber cover. Slide the fiber cover off as shown. Page 1 2.) With the fiber connector exposed, remove the dust plug, clean the fiber ends and terminate the SC equipped fiber. Danger! . Exposure to invisible LASER radiation may cause serious retinal dam- age or even blindness. Verify the optical source is disabled through the use of an optical power meter before handling optical fibers . 3.) Insert the fiber into the cover slot and slide the cover back onto the 72xx unit. Power 1.) Connect the 2.5mm DC power plug to the port labeled PWR. UPS 1.) The UPS alarms are con- nected via a MOLEX 43025-0800 connector. The pin orientation as viewed from the back as shown below. Page 2 POTS Connections 1.) Connect up to 2 phones to the ports labeled POTS1 and POTS2 identified below. LAN Connections 1.) Connect the computers/routers to the ports labeled ETH1 thru ETH4. CATV Connections 1.) Connect the television to the port labeled WIFI Connections 1.) Connect the Notebook computers/WIFI terminals to the SSID named “iphotonix- ONT” which can be changed manually. Page 3 PIN NAME ALM1 Power Input (+12 VDC) –2UPS Status: On Battery 13 UPS Status: Battery Missing 24Signal Return –5 Power 12V Return –6UPS Status: Replace Bettery 37 UPS Status: Low Battery 48No Connection (N/A) –video on demand services. They provide the follow- ing user features:(see Model List for exact features) CATV ports - provide CATV and Return service – – USB ports - provide data backups service – UPS ports - provide UPS service CATV. This port also supports Return se- rvice in some models. USB Connections 1.) Connect the flash-disk/portable hard disk to the port labeled USB on the left side of the units. USER CONTROLS The 72xx SFU ONT is equipped with an ON/OFF button. User functionality should be limited to this button LED Descriptions The 72xx SFU ONT has visual LED indicators to help the user determine the operational state of the unit. The LEDs are defined as follows: Page 4 PowerBatteryFAILON Unit is powered onOFF Unit is powered offON Battery is charged and unit is operating nor-mally on external power.Flashing Slow Unit is running off of battery power only. Check power supply to unit.Flashing Fast Battery is low and unit may turn off if exter-nal power is not restored.OFF Battery is missing or defective.ON Indicates Loss Of Signal (LOS). No optical signal is present.Flashing Slow Margnal signal indicates a weak optical sig-nal from carrier. Clean fiber connection per local procatice and check power with an opti-cal meter.

Navigation menu