Hisense Broand Multimedia Technologies 001 Gigabit-Capable Passive Optical Network Single Family Unit User Manual
Hisense Broadband Multimedia Technologies Co.,Ltd Gigabit-Capable Passive Optical Network Single Family Unit User Manual
R66001_User manual_Rev1
Flashing Fast Software upgrade has failed. OFF Optical signal is present and operating normally. ETH1-4 ON Ethernet link is operational. Flashing Indicates data transmission / reception. OFF No Ethernet link or port is not equipped. POTS ON Line is off hook (call active or in process). Flashing Slow Indicates ringing line. OFF Line is on hook (no call in process) or port is not equipped. MGMT ON Management channel (OMCI) active. OFF Management channel (OMCI) not active. WLAN ON WIFI function is active. Flashing Indicates data transmission / reception. OFF WIFI function is not active. Environmental Requirements Rated Voltage: Rated Current: Operating Temperature: Operating Relative Humidity: Storage Temperature: Storage Relative Humidity: DC 12V 2A +5°C to +40°C 5% to 85% -40°C to +60°C 0% to 95% Model List Model Functions 7259G 7257G 7258G 7253G 7281G 7251G Select 2POTS + 4GE + CATV + Return + WiFi 2POTS + 4GE + CATV + Return 2POTS + 4GE + CATV + WiFi 2POTS + 4GE + CATV 2POTS + 4GE + WiFi 2POTS + 4GE Page 5 FCC Notice -1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Safety Caution Statement To satisfy FCC RF exposure requirement for mobile and base station transmission devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Page 6 FCC Notice -2 The 72xxG North America edition is limited using channel 1-11. This limited operation can be only set by software and was done before the product down from the product line. All the products for North America marketing were embedded this limited before shipping. Customers have no way to choose the channel 12 & 13. Indoor Type PIN 2.) With the fiber connector exposed, remove the dust plug, clean the fiber ends and terminate the SC equipped fiber. Danger! . Exposure to invisible LASER radiation may cause serious retinal damage or even blindness. Verify the optical source is disabled through the use of an optical power meter before handling optical fibers OVERVIEW The 72xx SFU residential ONT delivers high quality VoIP voice service, Ethernet data service for highspeed internet access and IPTV broadcast video plus video on demand services. They provide the following user features:(see Model List for exact features) – – – – – – 2 POTS ports - provide voice telephone service 4 LAN ports - provide Ethernet connectivity WIFI ports - provide WIFI connectivity CATV ports - provide CATV and Return service USB ports - provide data backups service UPS ports - provide UPS service INSTALLATION The 72xx SFU ONT can be mounted vertically or horizontally on any flat surface. Unpack Unpack the unit and verify that it is free from shipping damage.: NAME ALM Power Input (+12 VDC) – UPS Status: On Battery UPS Status: Battery Missing Signal Return – Power 12V Return – UPS Status: Replace Bettery UPS Status: Low Battery No Connection (N/A) – Pins for the connector are Molex 46235-5002 NOTICE: Please adopt UL certificated UPS which meets Limited Power Source standard. USER CONTROLS The 72xx SFU ONT is equipped with an ON/OFF button. User functionality should be limited to this button 1.) Connect up to 2 phones to the ports labeled POTS1 and POTS2 identified below. LED Descriptions The 72xx SFU ONT has visual LED indicators to help the user determine the operational state of the unit. The LEDs are defined as follows: 3.) Insert the fiber into the cover slot and slide the cover back onto the 72xx unit. Power 1.) Connect the computers/routers to the ports labeled ETH1 thru ETH4. Desk Mount 1.) Set the unit on a flat surface considering the follo- ON Unit is powered on OFF Unit is powered off Battery wing: – – 1.) Connect the flash-disk/portable hard disk to the port labeled USB on the left side of the units. POTS Connections LAN Connections – – USB Connections within reach of the power source no thermal obstructions not in direct sunlight user ability to monitor/operate the unit CATV Connections Power Wall Mount 1.) Use wall anchors or wood screws (if mounting to plywood mounted on a wall), spaced 5.125” apart center to center. Fiber Connection 1.) Connect the 2.5mm DC power plug to the port labeled PWR. 1.) On the back left side of the unit is a fiber cover. Slide the fiber cover off as shown. UPS 1.) The UPS alarms are connected via a MOLEX 43025-0800 connector. The pin orientation as viewed from the back as shown below. Page 1 1.) Connect the television to the port labeled CATV. This port also supports Return service in some models. ON Battery is charged and unit is operating normally on external power. Flashing Slow Unit is running off of battery power only. Check power supply to unit. Flashing Fast Battery is low and unit may turn off if external power is not restored. OFF Battery is missing or defective. FAIL WIFI Connections 1.) Connect the Notebook computers/WIFI terminals to the SSID named “iphotonixONT” which can be changed manually. Page 2 Page 3 ON Indicates Loss Of Signal (LOS). No optical signal is present. Flashing Slow Margnal signal indicates a weak optical signal from carrier. Clean fiber connection per local procatice and check power with an optical meter. Page 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 Producer : GPL Ghostscript 8.15 Create Date : 2012:11:06 18:26:36 Modify Date : 2012:11:06 18:26:36 Title : Microsoft Word - User_Manual.doc Creator : PScript5.dll Version 5.2.2 Author : yuchingEXIF Metadata provided by EXIF.tools