Hobbico T4-2400 Radio Control System User Manual IYFT4 2400 UserManual

Download:
Mirror Download [FCC.gov]
Document ID	1018643
Application ID	7ot3DUNaFuZbDjyufAm4XQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.31kB (53920 bits)
Date Submitted	2008-10-21 00:00:00
Date Available	2008-10-21 00:00:00
Creation Date	2008-10-16 10:49:47
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2008-10-16 10:49:47
Document Title	Microsoft Word - IYFT4-2400_UserManual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	olic.huang

T4-2400 Transmitter operation Introduction
1. Electronic Specification
a. Operation frequency: 2402- 2480MHz, total 79 frequencies (the space of close
frequencies is 1 MHz)
b. FHSS transmitter mode
c. Output power≤4Mw
d. Channel: 4 proportional
e. Operation voltage: 4.8V
f. Operation current＜25mA
2. Using Guide
a. Power on the transmitter, the voltage of the battery no less than 4.8V, all the 3 LED s
(from left to right: red, yellow and green) illuminated; when the voltage of the battery
between 4.4V-4V, green light off; when the voltage below 4V, just the red light on, and
then we must charge the battery with the included charger. Please review the attached
circuit diagram of the charger.
b. As the diagram 1 shown, the top transmitter case has 2 control sticks, and their
performance as following:
Left stick,
Up and down, control the Throttle
Left and right, control the Rudder
Right stick,
UP and down, control the Elevator
Left and Right, control the Rudder
There are 4 trim levers near the 2 sticks, respectively trim the throttle, rudder, elevator
and aileron throw.
c.
There are 4 switches on the right bottom of the top case of the transmitter, respectively
for aileron, elevator, throttle and rudder reverse switches.
d. In the left corner, there is a trainer switch, when the 2 transmitters connected by a trainer
core with the trainer jack at the back of the transmitter; stir the trainer switch can make
the two transmitters have the trainer function.
e.
f.
As the diagram 2 shown, it the back sight diagrams of the transmitter, the charger jack on
the left side.
Diagram is showing the receiver, there are a code knob and a LED. First time to use this
radio, should be turn on the transmitter firstly, and then connect the receiver battery, and
press the code knob on the receiver for 5 seconds, then the LED of receiver be on.
Notes: while coding the transmitter and receiver, do not allow any other transmitter in the
same series to operate within the range of receiver.
FCC NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could
void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:10:16 10:49:47+08:00
Create Date                     : 2008:10:16 10:49:47+08:00
Format                          : application/pdf
Title                           : Microsoft Word - IYFT4-2400_UserManual.doc
Creator                         : olic.huang
Document ID                     : uuid:445a8846-3d6b-43bf-8fd5-59835b5c4b1d
Instance ID                     : uuid:3d09c8e3-06b0-4592-bead-08d7eaebeecc
Page Count                      : 3
Author                          : olic.huang

EXIF Metadata provided by EXIF.tools